aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: ase: enable USB and wirelessMathias Kresin2017-10-041-2/+4
| | | | | | | | | | Add the missing USB related kernel config options to target config. Enable wireless as well, wireless is supported via USB. Fixes compile/packaging errors with the libertas wireless kernel module. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ase: fix SPI supportMathias Kresin2017-10-043-1/+2
| | | | | | | | | | Do not disable SPI in the subtarget, otherwise the SPI driver can not be used. Disable SPI by default and enable it in the board specific device tree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: select PCI support in subtargetsMathias Kresin2017-10-044-8/+23
| | | | | | | | | | | | | | | | AmazonSE and Falcon do not have support for PCI and it can't be unselected in the subtarget kernel config. This way the enabled PCI support is inherit from the higher level config to the subtarget. If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and all packages depending on this config symbol will be build and at least some of them fail due to missing pci functions. The issue can be observed if all kmods and all non-shared packages are build. Fix the issue by enabling PCI support only in subtargets with PCI support. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ase: cleanup kernel configMathias Kresin2017-10-041-2/+0
| | | | | | | | The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or global kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xway: cleanup kernel configMathias Kresin2017-10-041-29/+0
| | | | | | | | | | CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch to the upstreamed driver. All other removed subtarget kernel config options are already set by the target specific or global kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: cleanup kernel configMathias Kresin2017-10-041-3/+8
| | | | | | | | | | | CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel. CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch to the upstreamed driver. Add autoselected dependecies to the kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: fix sorting of kernel configMathias Kresin2017-10-041-6/+6
| | | | | | | Use the kconfig script to sort the kernel config. It makes further changes more obvious. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop obsolete kernel config optionsMathias Kresin2017-10-042-4/+0
| | | | | | | | | | | CONFIG_GPIO_DEVRES was removed with kernel commit f9c22ec6c1c5 ("gpio: Remove GPIO_DEVRES option") during kernel 4.9 development. CONFIG_HAVE_BPF_JIT was removed with kernel commit 6077776b5908 ("bpf: split HAVE_BPF_JIT into cBPF and eBPF variant") during kernel 4.7 development. Signed-off-by: Mathias Kresin <dev@kresin.me>
* sunxi: add Orange Pi R1 supportHauke Mehrtens2017-10-012-0/+206
| | | | | | | | | | | | | | | The following features are working and tested: * both Ethernet ports * MMC * LED The following features are not working: * Wifi (There is a crappy driver we could port) * SPI flash (I haven't looked into this) I haven't tried out the rest. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: owl-loader: fix compile warningHauke Mehrtens2017-10-011-1/+1
| | | | | | | | | | | | | check if the config option CONFIG_LANTIQ is defined. This fixes the following warning: CC [M] drivers/misc/owl-loader.o drivers/misc/owl-loader.c: In function 'ath9k_pci_fixup': drivers/misc/owl-loader.c:92:5: warning: "CONFIG_LANTIQ" is not defined [-Wundef] #if CONFIG_LANTIQ ^ Fixes: e9401a2335cc ("kernel: owl-loader for delayed Atheros ath9k fixup") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: H3: add device tree changes for H3 EthernetHauke Mehrtens2017-10-015-0/+229
| | | | | | | This adds the device tree changes needed to make the GMAC stmmac driver working for the Allwinner H3 SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: A64: add device tree changes for A64 EthernetHauke Mehrtens2017-10-016-0/+241
| | | | | | | This adds the device tree changes needed to make the GMAC stmmac driver working for the Allwinner A64 SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: backport the stmmac driver from kernel 4.13Hauke Mehrtens2017-10-017-0/+13682
| | | | | | | | | | | This adds support for the GMAC which is use in the A64 and other Allwinner chips by backporting the changes from the kernel versions 4.13. Some commits are not backported which are adding support for newly introduced APIs which are not available in kernel 4.9. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update 4.4 to 4.4.89Kevin Darbyshire-Bryant2017-09-293-19/+19
| | | | | | | Refresh patches. Compile & run tested on ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ar71xx: unify CONFIG_CMDLINEFelix Fietkau2017-09-284-4/+1
| | | | | | | Booting from jffs2 directly is no longer supported, use rootfstype=squashfs consistently for all subtargets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: reduce napi_weight in the ethernet driver.Rosen Penev2017-09-281-1/+1
| | | | | | Currently dmsg a weight of 128 which is above the kernel limit of 64. Silence the warning. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: add MT29F2G08ABAE NAND flash supportRoman Yeryomin2017-09-281-1/+2
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: improve Xiaomi Mi Router 3G supportKevin Darbyshire-Bryant2017-09-284-26/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit improves support for the Xiaomi Mi Router 3G originally added in commit 6e283cdc0da25928f8148805ebef7f8f2b769ee8 Improvements: - Remove software watchdog as hardware watchdog now working as per commit 3fbf3ab44f5cebb22e30a4c8681b13341feed6a6 for all mt7621 devices. - Reset button polarity corrected - length of press determines reboot (short press) vs. reset to defaults (long press) behaviour. - Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit link and blink on activity. Green LEDs driven directly by switch indicating any link speed and tx activity. - USB port power on/off GPIO exposed as 'usbpower' - Add access to uboot environment settings for checking/setting uboot boot order preference from user space. Changes: - Front LED indicator is physically made of independent Yellow/Amber, Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel indicator, hence the colour behaviour is similar to an RGB LED. RGB LEDs are not supported at this time because they produce colour results that do not then match colour labels, e.g. enabling 'mir3g:red' and 'mir3g:blue' would result in a purple indicator and we have no such label for purple. The yellow, red & blue LEDs have been split out as individual yellow, red & blue status LEDs, with yellow being the default status LED as before and with red's WAN and blue's USB default associations removed. - Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan layout. eth0.1 is LAN, eth0.2 is WAN - Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet leakage between kernel switch init and uci swconfig uboot behaviour & system 'recovery' uboot expects to find bootable kernels at nand addresses 0x200000 & 0x600000 known by uboot as "system 1" and "system 2" respectively. uboot chooses which system to hand control to based on 3 environment variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed last_success represents a preference for a particular system and is set to 0 for system 1, set to 1 for system 2. last_success is considered *if* and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either* failed flags are set then uboot will attempt to hand control to the non failed system. If both failed flags are set then uboot will check the uImage CRC of system 1 and hand control to it if ok. If the uImage CRC of system is not ok, uboot will hand control to system 2 irrespective of system 2's uImage CRC. NOTE: uboot only ever sets failed flags, it *never* clears them. uboot sets a system's failed flag if that system's was selected for boot but the uImage CRC is incorrect. Fortunately with serial console access, uboot provides the ability to boot an initramfs image transferred via tftp, similarly an image may be flashed to nand however it will flash to *both* kernels so a backup of stock kernel image is suggested. Note that the suggested install procedure below set's system 1's failed flag (stock) thus uboot ignores the last_success preference and boots LEDE located in system 2. Considerable thought has gone into whether LEDE should replace both kernels, only one (and which one) etc. LEDE kernels do not include a minimal rootfs and thus unlike the stock kernel cannot include a method of controlling uboot environment variables in the event of rootfs mount failure. Similarly uboot fails to provide an external mechanism for indicating boot system failure. Installation - from stock. Installation through telnet/ssh: - copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it from LEDE download site to /tmp - switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if wgetted from LEDE download site - run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1 - run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0 - run: nvram set flag_try_sys1_failed=1 - run: nvram commit - run: reboot Recovery - to stock. Assuming you used the above installation instructions you will have a stock kernel image in system 1. If it can be booted then it may be used to perform a stock firmware recovery, thus erasing LEDE completely. From a 'working' LEDE state (even failsafe) Failsafe only: - run: mount_root - run: sh /etc/uci-defaults/30_uboot-envtools Then do the steps for 'All' All: - run: fw_setenv flag_try_sys2_failed 1 - run: reboot The board will reboot into system 1 (stock basic kernel) and wait with system red light slowly blinking for a FAT formatted usb stick with a recovery image to be inserted. Press and hold the reset button for around 1 second. Status LED will turn yellow during recovery and blue when recovery complete. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: RT5350F-OLINUXINO: enable ttyS1Zoltan Gyarmati2017-09-281-1/+16
| | | | | | | | | The RT5350F's second UART pins are available on the base module and on the EVB as well, so enable it in the device tree. In order to keep the origian serial port numbering (ttyS0 is the serial console), aliases added for the UART devices. Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
* ramips: RT5350F-OLINUXINO: enable i2cZoltan Gyarmati2017-09-281-0/+4
| | | | | | | The RT5350F i2c pins is available on the base module and on the EVB as well, so enable it in the dts. Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
* ramips: RT5350F-OLINUXINO: invert WiFi LED polarityZoltan Gyarmati2017-09-281-0/+1
| | | | | | | The polarity of WLAN_ACT LED on the base module needs to inverted in order to be 'on' when the WiFi interface is active Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
* ramips: introduce RT5350F-OLINUXINO.dtsiZoltan Gyarmati2017-09-283-140/+76
| | | | | | | | | | The RT5350F-OLINUXINO(-EVB).dts files' content are nearly the same, so to avoid code duplication this patch creates RT5350F-OLINUXINO.dtsi file which covers the base board's features. The corresponding RT5350F-OLINUXINO.dts just includes the new .dtsi and the RT5350F-OLINUXINO-EVB.dts adds the EVB specific GPIO config. Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
* ramips: add 'lwlll' portmap to mt7530 switchKevin Darbyshire-Bryant2017-09-281-1/+7
| | | | | | | | | | | The Xiaomi Mi Router 3G uses this deranged vlan portmap. Add support so that packets are not leaked across all switch ports when reset. Fix a whitespace nit while we're here. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [fix wrong pvids order] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: fix failsafe mode networkingKevin Darbyshire-Bryant2017-09-281-2/+7
| | | | | | | | | | Disable VLANs on mt7621 boards with mt7530 switches on failsafe entry. Allows failsafe networking to work correctly. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [fixed default case syntax error] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update 4.9 to 4.9.52Stijn Tintel2017-09-281-1/+1
| | | | | | | | Refresh patches. Compile-tested on x86/64. Runtime-tested on x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* Revert "brcm47xx: Fix sysupgrade with E1200v1"Hauke Mehrtens2017-09-251-1/+0
| | | | | | | | | | This reverts commit 31e9445b7e614f54daa0caf3148e223d088311ab. "Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code can not detect this device. Stefan Lippers-Hollmann also found a typo in this patch "cybetran" instead of "cybertan". Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: Fix sysupgrade with E1200v1Rosen Penev2017-09-241-0/+1
| | | | | | Entry was missing for some reason. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* sunxi: add Olimex A20-OLinuXino-LIME2-eMMCLucian Cristian2017-09-241-0/+10
| | | | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> [replaced u-boot patch with original version from u-boot git] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: don't scrimp on memory on big ironPhilip Prindeville2017-09-242-4/+10
| | | | | | | | | x86_64 platforms typically don't lack memory, so don't needlessly economize memory if fq_codel on capable platforms. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> [Add a comment to the patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix missing mediatek wdtKevin Darbyshire-Bryant2017-09-222-2/+2
| | | | | | | | | | | | | | | mediatek MT7621 soc watchdog DTS id was renamed from "mtk,mt7621-wdt" to "mediatek,mt7621-wdt" when driver upstreamed to kernel 4.5 Update mt7621.dtsi & mt7628an.dtsi definitions to match upstreamed kernel. Restores hardward watchdog functionality on mt7621 devices under linux 4.9 Tested on: MIR3G Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: update 4.9 to 4.9.51Stijn Tintel2017-09-2012-37/+37
| | | | | | | | | | | | Refresh patches. Compile-tested on octeon and x86/64. Runtime-tested on octeon and x86/64. Fixes the following CVEs: - CVE-2017-14106 - CVE-2017-14497 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* at91: Add UBI parameters for sama5d4.Sandeep Sheriker Mallikarjun2017-09-201-1/+6
| | | | | | Add UBIFS_OPTS & UBINIZE_OPTS parameters for sama5d4 Xplained board. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: Add SAMA5D4 deviceSandeep Sheriker Mallikarjun2017-09-202-0/+11
| | | | | | | Add support for SAMA5D4 with target device as at91-sama5d4_xplained in SAMA5 subtarget and build images for SAMA5D4 Xplained board. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: Add SAMA5D2 deviceSandeep Sheriker Mallikarjun2017-09-202-0/+11
| | | | | | | Add support for SAMA5D2 with target device as at91-sama5d2_xplained in SAMA5 subtarget and build images for SAMA5D2 Xplained board. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: Install zImage.Sandeep Sheriker Mallikarjun2017-09-201-0/+6
| | | | | | Installing zImage to bin folder of device target. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: Renaming subtarget sama5d3 to sama5Sandeep Sheriker Mallikarjun2017-09-205-8/+8
| | | | | | | | | Renaming at91 subtarget sama5d3 to sama5 and using at91-sama5d3_xplained as a target device in sama5 subtarget.This will enable to add other sama5d2 & sama5d4 target devices in sama5 subtraget.This will avoid code duplication when sama5d2 & sama5d4 added as different subtarget. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* sunxi: add Olimex A20-OlinuXino-LIME2Lucian Cristian2017-09-181-0/+10
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* sunxi: Add A64 support with cortex53 subtargetHauke Mehrtens2017-09-185-1/+135
| | | | | | | | | | | | This adds initial support for the A64 Allwinner SoC to LEDE. It will be build in the new cortexa53 subtarget. Currently it only supports the pine64 and the image is able to boot on this SoC. Camera, Ethernet, HDMI and other parts are currently not working. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Backport patches from kernel 4.11 for A64Hauke Mehrtens2017-09-1814-0/+640
| | | | | | | This backports some more patches from kernel 4.11 adding more devices to the device tree of the A64 SoC. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Backport patches needed for A64Hauke Mehrtens2017-09-1825-0/+4665
| | | | | | | | This backports multiple patches from kernel 4.10 which are adding missing support for the A64 and the pine64 board. These are the device tree files, the pinctlk and the clock driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: split into cortex A8 and A7 subtargetHauke Mehrtens2017-09-188-151/+223
| | | | | | Now we can activate some compiler optimizations for the cortex A7. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: fix build of rtc package when module not availableHauke Mehrtens2017-09-181-2/+2
| | | | | | | If the Kconfig option CONFIG_RTC_DRV_SUNXI is not selected this package should be be build. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for kernel 4.9Hauke Mehrtens2017-09-184-1/+689
| | | | | | | Most of the patches were backpoprts from the mainline kernel and are integrated upstream now. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: add some config optionsHauke Mehrtens2017-09-181-0/+10
| | | | | | These are needed for the sunxi target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rb532: drop 4.4 supportStijn Tintel2017-09-184-268/+0
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* rb532: add myself as maintainerRoman Yeryomin2017-09-181-0/+1
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: switch to 4.9Roman Yeryomin2017-09-181-1/+1
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: add support for 4.9Roman Yeryomin2017-09-1810-0/+675
| | | | | | | | Includes latest korina fixes. Signed-off-by: Roman Yeryomin <roman@advem.lv> [rewrite commit message (subject <= 50 characters)] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* rb532: set lan interface type to brigdeRoman Yeryomin2017-09-181-0/+1
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: increase kernel size limitRoman Yeryomin2017-09-181-1/+1
| | | | | | | | This is required to support kernel 4.9. Signed-off-by: Roman Yeryomin <roman@advem.lv> [rewrite commit message (subject <= 50 characters)] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 05:16:19 +0000