aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: Adjust SoC name of AVM Fritz!Box 4040Sven Eckelmann2018-03-233-2/+2
| | | | | | | The AVM Fritz!Box 4040 uses an IPQ4018 as SoC and not an IPQ4019. The DTS must be adjusted to reflect this. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Use constant to set gpio active low/highSven Eckelmann2018-03-237-8/+9
| | | | | | | | | The GPIO configuration in the DTS have as third parameter the active low/high configuration. This parameter is not easy to parse by humans when it is only set to 0/1. It is better to use the predefined constants GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Fix DTS status parameter valuesSven Eckelmann2018-03-234-47/+47
| | | | | | | | The "Devicetree Specification, Release v0.2 - 2.3.4 status" [1] only allows the "okay" value for an operational device. The "ok" value will be accepted by the kernel but should be avoided. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Provide prefered DTS config name for A42Sven Eckelmann2018-03-231-0/+1
| | | | | | | | The OpenMesh A42 will use the default config entry in the FIT when no other on is found but prefers the config@om.a42. This only becomes relevant when a Multi-FIT image is prepared for this device. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Remove SUPPORTED_DEVICES for A42Sven Eckelmann2018-03-231-1/+0
| | | | | | | The SUPPORTED_DEVICES will be defined automatically via Device/Default in ipq40xx. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* kernel: fix offloading connections with SNAT + DNATFelix Fietkau2018-03-231-0/+23
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix flow offload UDP handling issueFelix Fietkau2018-03-231-0/+48
| | | | | | Only run the TCP state check for TCP connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: b53: fix compilation on BCM47XXRafał Miłecki2018-03-211-0/+2
| | | | | | | | | This fixes: drivers/net/phy/b53/b53_priv.h:325:2: error: enumeration value '<board>' not handled in switch [-Werror=switch] errors. Fixes: 0de2213eeade7 ("kernel: b53: look for NVRAM's "robo_reset" entry on every platform") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: b53: look for NVRAM's "robo_reset" entry on every platformRafał Miłecki2018-03-211-6/+8
| | | | | | | | | | Since kernel 4.1 bcm47xx_nvram_gpio_pin() is now defined in a global header and can be safely called even on non-Broadcom platforms. This change makes b53 look for "robo_reset" on ARCH_BCM_5301X and slightly simplifies the code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kirkwood: fix initramfs boot warning on iconnectPaul Wassi2018-03-202-2/+20
| | | | | | | | | | The chosen dts configuration linux,initrd-* gives an error message on bootup of kirkwood-iconnect. Since initramfs/initrd is not used remove these options from the dts. Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kirkwood: switch to kernel 4.14Paul Wassi2018-03-201-1/+1
| | | | Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kirkwood: add kernel 4.14 supportPaul Wassi2018-03-2015-0/+1524
| | | | | | | | | Add patches for 4.14, undoing upstream changes for Linksys devices regarding DSA. Instead, the switchdev driver marvell,88e6171 is used. Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* mvebu: disable cpu idle on WRT1900ACv1Felix Fietkau2018-03-191-0/+10
| | | | | | | | | | | | | | | A regression seriously affecting the Linksys WRT1900ACv1 (Mamba) was introduced some time between the OpenWrt/LEDE v4.4 and v4.9 kernels. The root cause has not yet been identified, despite many attempts for more than a year. Disabling the SoC specific CPU idle support should mitigate this issue. The symptoms on an affected system are unwanted reboots at a variable frequency. In many cases almost immediately after boot, causing a bootloop. This effectively disables support for Mamba on OpenWrt with kernels > v4.4. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix DM200 boot with fake uImage headersThomas Nixon2018-03-181-0/+4
| | | | | | | | | | | | | | The latest bootloader versions load the firmware into memory and call `chk_dniimg` (defined in Netgear GPL release), which expects to find three consecutive block-aligned uImages. Add two fake uImage headers after the kernel to fool this check. This wastes up to 128k of space for alignment. The alternative would be to put the rootfs in a second uImage, but this would limit the firmware size to 0x710000 (the number of bytes loaded and verified by the bootloader) instead of 0x7b0000 (the size of the firmware partition). Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* lantiq: fix AVM initramfs imageValentin Spreckels2018-03-181-0/+1
| | | | | | Create an initramfs that can be used with the EVA bootloader. Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
* ar71xx: fix Fritz 300e initramfs imageMathias Kresin2018-03-181-0/+1
| | | | | | Create an initramfs that can be used with the EVA bootloader. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link TL-WR902AC v3Peter Lundkvist2018-03-186-0/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router based on MediaTek MT7628N + MT7650E. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet * MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment. Therefore 5Ghz won' work. Flash instruction: The only way to flash LEDE image in TL-WR902AC v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com> [drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-116-A1/2Pawel Dembicki2018-03-1810-1/+175
| | | | | | | | | | | | | | | | | | | | | | | | | The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC. Specification: MediaTek MT7620N (580 Mhz) 32 MB of RAM 8 MB of FLASH 802.11bgn radio 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) 2x external, non-detachable antennas UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1) 6x LED (GPIO-controlled), 2x button JBOOT bootloader Known issues: WAN LED is drived by uartl tx pin. I decide to use this pin as uartlite tx pin. Installation: Apply factory image via http web-gui. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mvebu: Disable internal RTC on Linksys devicesHauke Mehrtens2018-03-171-0/+28
| | | | | | | | | | The internal RTC does not work correctly on these Linksys boards based on Marvell SoCs. It is off by 3 minutes in 10 minutes running, this was reported by multiple users. On the Linksys Mamba device the device tree comment says that no crystal is connected to the internal RTC, this is probably also true for the other devices. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: Add Solidrun RTC init patch.Rosen Penev2018-03-171-0/+74
| | | | | | | | Some boards like the Turris Omnia have an RTC chip that does not get initialized. Initializing the RTC at the driver level helps get rid of bootloader hacks that write special register values. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu: Backport RTC trimming support.Rosen Penev2018-03-171-0/+143
| | | | | | This enables a higher precision mode for the RTC. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* sunxi: update Xunlong Orange Pi Zero Plus dts fileHauke Mehrtens2018-03-171-56/+48
| | | | | | This updates the DTS file to the version send upstream Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.27Stijn Segers2018-03-1717-96/+36
| | | | | | | | | | * Refreshed patches. * Deleted 812-pci-dwc-fix-enumeration.patch (was accepted upstream) Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: bump 4.4 to 4.4.121Koen Vandeputte2018-03-175-17/+17
| | | | | | | | | - Refreshed all patches - Only compile-tested Compile tested on: Gemini Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.87Koen Vandeputte2018-03-1711-17/+17
| | | | | | | | | - Refreshed all patches Compile tested on: ar71xx Runtime tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* generic: revert broken LED core patchMatthias Schiffer2018-03-171-0/+26
| | | | | | | | The patch breaks LED operation and has already been reverted in 4.4.121. 4.9.87 is still affected; revert it locally until the issue is sorted out upstream. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ipq40xx: fix GL.iNet GL-B1300Mathias Kresin2018-03-172-319/+0
| | | | | | | | | | | The deletion of the mdio node childs was meant for testing and were committed accidentally. Without the mdio nodes the network isn't initialised. While at it, remove the orphaned qcom-ipq4019-gl-b1300.dts as well. Fixes: FS#1439 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for Compex WPJ428Sven Eckelmann2018-03-176-1/+308
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ4028 * 256 MB of RAM * 32 MB of SPI NOR flash (mx25l25635e) * 128 MB of SPI NAND flash (gd5f1gq4ucy1g) * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2 fully software controllable GPIO-LEDs * 2 additional GPIO-LEDs which also affect the SIM card detection * 1x button (reset) * 1x GPIO buzzer * 1x USB (xHCI) * 1x NGFF (USB-only with Dual-SIM support, untested) * TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC) * 2x gigabit ethernet - phy@mdio4: + Manual: Ethernet port 0 + gmac0 (ethaddr) in original firmware + 802.3af POE (HV version) + 24v passive POE (LV version) - phy@mdio3: + Manual: Ethernet port 1 + gmac1 (eth1addr) in original firmware * DC Jack connector + 24-56V (HV version) + 12-24V (LV version) The SPI NAND flash isn't supported at the moment. The bootloader has to be updated before OpenWrt is installed to fix a reboot problem. The nor-ipq40xx-single.img from https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware has to be downloaded and the transfered in u-boot via TFTP set ipaddr 192.168.1.11 set serverip 192.168.1.10 ping ${serverip} tftpboot 0x84000000 nor-ipq40xx-single.img imgaddr=0x84000000 && source $imgaddr:script The sysupgrade image can be installed directly on flash using u-boot: sf probe tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin sf erase 0x00180000 +$filesize sf write 0x84000000 0x00180000 $filesize bootipq The initramfs image can be started using tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb set fdt_high 0x83000000 bootm 0x82000000 The used SIM card slot can be changed using # slot 1 (also enables orange LED) echo 1 > /sys/class/gpio/gpio3/value # slot 2 echo 0 > /sys/class/gpio/gpio3/value It can be checked whether a SIM card is inserted in the current slot and the red LED is subsequently on via: echo 2 > /sys/class/gpio/export cat /sys/class/gpio/gpio2/value Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: fix switch for Nexx devicesINAGAKI Hiroshi2018-03-171-5/+8
| | | | | | | | | | | | | | | | | There are 2 ethernet ports on Nexx WT1520 and WT3020. These ethernet ports are assigned as follows, and other ports cannot be used. - WT1520: - port0 -> lan - port4 -> wan - WT3020: - port0 -> wan - port4 -> lan I dropped ports that cannot be used. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: add support for Ubiquiti Litebeam M5Arne Zachlod2018-03-158-0/+78
| | | | | | | | | | | | | | | | | Specification: - SoC: Atheros AR9342 - Flash: 8 MiB - RAM: 64 MiB - UART: 1x UART on PCB - 115200 8N1 - Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A) Doesn't work: * Flash via TFTP with Ubiquiti Uboot Installation via vendor firmware: - upload factory image via webinterface Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ipq806x: add support for Compex WPQ864Christian Mehlis2018-03-156-13/+601
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: unset uboot build by defaultMathias Kresin2018-03-152-1/+2
| | | | | | | | Initialise the UBOOT variable by default. Otherwise it will be unintended inherit to following images if set and causes an uboot build where not required. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: make mtd patches apply againHauke Mehrtens2018-03-155-27/+27
| | | | | | | | | This makes some of the mtd patches apply again after some generic patches were changed. These problems where found by build bot. Fixes: ac9bcefa3b044 ("kernel: use V10 of mtd patchset adding support for "compatible" string") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add Cisco Meraki MR33 SupportChris Blake2018-03-1410-1/+861
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13Christian Lamparter2018-03-1410-2/+447
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix GL.iNet GL-B1300 supportMathias Kresin2018-03-144-6/+322
| | | | | | | | | | | | | | | | | | | | Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: remove block- and pagesize from FB4040David Bauer2018-03-142-24/+0
| | | | | | | | | | | | This removes the block- and pagesize from the FritzBox 4040 image description, fixing incorrectly working sysupgrade. With this commit, the default values for block- and pagesize are used. Signed-off-by: David Bauer <mail@david-bauer.net> [chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: OpenMesh A42 overhaulChristian Lamparter2018-03-143-88/+81
| | | | | | | | | | | Sort the soc entries in the dts by address and use dtc labels whenever possible. Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an IPQ4019. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix apss cpu overclocking spamChristian Lamparter2018-03-142-2/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's an interaction issue between the clk changes:" clk: qcom: ipq4019: Add the apss cpu pll divider clock node clk: qcom: ipq4019: remove fixed clocks and add pll clocks " and the cpufreq-dt. cpufreq-dt is now spamming the kernel-log with the following: [ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 761142857 (-34) This only happens on certain devices like the Compex WPJ428 and AVM FritzBox!4040. However, other devices like the Asus RT-AC58U and Meraki MR33 work just fine. The issue stem from the fact that all higher CPU-Clocks are achieved by switching the clock-parent to the P_DDRPLLAPSS (ddrpllapss). Which is set by Qualcomm's proprietary bootcode as part of the DDR calibration. For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked at round 533 MHz (ddrpllsdcc = 190285714 Hz). whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx/ipq806x: move qcom-dwc3 usb driver to genericMathias Kresin2018-03-142-66/+0
| | | | | | | If the a kernel package exists within multiple targets an error/warning is shown. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add targetJohn Crispin2018-03-1451-0/+25706
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: drop ipq40xx supportJohn Crispin2018-03-1448-15076/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* kernel: use V10 of mtd patchset adding support for "compatible" stringRafał Miłecki2018-03-1414-272/+548
| | | | | | | | | | | | | In the commit bde5e7a632ef0 ("kernel: backport mtd implementation for "compatible" in "partitions" subnode") patches that got accepted into l2-mtd.git were backported to the kernels 4.9 and 4.14. Unfortunately there was a regression report, patches were dropped and never reached 4.16. This commit replaces these pseudo-backports with the latest version that includes regression fix and futher changes that were requested. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7620n: add mdio node and disable port4 by defaultMathias Kresin2018-03-131-1/+8
| | | | | | | | | | | | | | | | | Revert the changes I applied to aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default"). The driver expects a node mdio-bus to be present, regardless of the actual node status. If the node is missing the driver fails to load with mtk_soc_eth 10100000.ethernet: no mdio-bus child node found Disable port4 by default again. If the port is enabled but not present, a "invalid port id 4" warning is shown during boot. Fixes: FS#1428 Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=n"John Crispin2018-03-131-3/+12
| | | | | | | | This reverts commit cff2dedebc665dc1d3d64d850afd0124c6d35eaa. This patch causes build issues Signed-off-by: John Crispin <john@phrozen.org>
* kernel: b53: drop support for old location of bcm47xx_nvram.hRafał Miłecki2018-03-131-3/+1
| | | | | | | | In kernels 4.0 and older that header file was located in some subdir of arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so that code isn't needed anymore. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=nAndré Draszik2018-03-131-12/+3
| | | | | | | | | | | | | | | If CONFIG_GPIO_SYSFS=n, compilation fails with drivers/built-in.o: In function `gpio_export_with_name': include/asm-generic/gpio.h:128: undefined reference to `__gpiod_export' This is because the stub in that case has the wrong name, _gpiod_export() - note the missing underscore (_) at the start. Fix the stub, and add the correct prototype for the real implementation. Signed-off-by: André Draszik <git@andred.net>
* swconfig: convert swdevs_lock from spinlock to mutexFelix Fietkau2018-03-121-3/+3
| | | | | | Should fix some sleep-while-atomic issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: merge a pending fix for HFSC warnings/slowdowns (fixes FS#1136)Felix Fietkau2018-03-119-9/+267
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: unroll MIPS r4k cache blast functionFelix Fietkau2018-03-103-7/+180
| | | | | | | | | | | Optimize the compiler output for larger cache blast cases that are common for DMA-based networking. On ar71xx, I measured a routing throughput increase of ~8% Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com> Signed-off-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 20:20:18 +0000