aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/x86
Commit message (Collapse)AuthorAgeFilesLines
* [x86] add missing kvm_guest kernel optionsJohn Crispin2012-09-051-0/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33319 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] set xen images to gzip compression, fixes #11970John Crispin2012-08-151-0/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33192 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Fix hard reset of alix/soekris hardware under heavy NIC loadJo-Philipp Wich2012-08-091-0/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following patch corrects a hard reset that occurs on alix and soekris net5501 hardware. Specifically, this is an issue with the via rhine NIC driver. Under periods of extreme load, the via rhine driver can cause a reset of the entire system. When this happens no output is seen on the console, the device simply reboots. This was reported in the following ticket: Consistent crash on Soekris NET5501 https://dev.openwrt.org/ticket/11882 I was able to reproduce the problem locally with numerous alix 2d13 platforms. Under heavy 64 byte frame size load from a Smartbits traffic generator, the alix hardware will hard reset in under 5 minutes. The same hardware, under the same load, on FreeBSD 9.0 does not reset. The patch below backports most of the via rhine changes from kernel 3.5. With OpenWrt trunk being on kernel 3.3.8, it seemed prudent to bring these changes in to avoid this serious issue. I've tested this heavily in my test environment and was able to keep the device stable under load for extended periods of time without any resets. Also, a nice side effect of this change is that it significantly raises the performance the platform. Without this patch the alix 2d13 can move approximately 29,000 packets per second at 64 byte frame sizes. After this patch the alix can move 52,000 packets per second at 64 byte frame sizes. I put this patch under the x86 patches as those are the only platforms with via rhine hardware that I'm aware of. If it needs to go some place else please let me know. Thanks, Adam Signed-off-by: Adam Gensler <openwrt@kristenandadam.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33072 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] make kmod-fb dependent on DISPLAY_SUPPORT and update targets ↵Florian Fainelli2012-07-251-0/+1
| | | | | | accordingly git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32869 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] move leds modules back to target modules.mkFlorian Fainelli2012-07-251-0/+32
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32851 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] move i2c modules back to target modules.mkFlorian Fainelli2012-07-251-0/+34
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32850 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] move more x86-specific modules back to target modules.mkFlorian Fainelli2012-07-251-0/+175
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32848 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] move x86 specific ide/pata modules to x86' modules.mkFlorian Fainelli2012-07-251-0/+73
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32846 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] Fix sysupgrade for squashfs, jffs2 and ext4 imagesVasilis Tsiligiannis2012-06-192-16/+55
| | | | | | | * use 'fsync' with 'dd' for image writing * save config to boot partition git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32465 3c298f89-4303-0410-b956-a3cf2f4a3e73
* optimize kernel config for kvm_guestJo-Philipp Wich2012-06-181-1/+3
| | | | | | | | | | This patch enables few extra kernel options for the kvm_guest subtarget: - Tickless kernel to avoid timer ticks in idle guests, reduces CPU usage - Enable paravirtualization steal time support Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32436 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [kvm_guest] remove inittab overrideJo-Philipp Wich2012-06-181-5/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32422 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] use ttyS0 @ 115200 baud as default for KVM guestsJo-Philipp Wich2012-06-151-3/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32384 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [kernel] bump to 3.3.8John Crispin2012-06-051-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32055 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.3 to 3.3.7Gabor Juhos2012-05-231-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31848 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: remove support for old kernelsGabor Juhos2012-05-1816-1916/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31804 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: remove subtarget specific LINUX_VERSION overridesGabor Juhos2012-05-1810-11/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31803 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/ep80579: switch to 3.3Gabor Juhos2012-05-182-0/+12
| | | | | | | Also fix build errors in the ep80579-drivers package. Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31802 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/olpc: switch to 3.3Gabor Juhos2012-05-182-0/+123
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31784 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: image: select bootscript images by default for OLPCGabor Juhos2012-05-181-0/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31783 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/thincan: switch to 3.3Gabor Juhos2012-05-172-0/+16
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31765 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/xen_domu: switch to 3.3Gabor Juhos2012-05-172-0/+76
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31764 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/kvm_guest: switch to 3.3Gabor Juhos2012-05-172-0/+77
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31763 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/generic: switch to 3.3Gabor Juhos2012-05-172-0/+113
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31762 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/alix2: switch to 3.3Gabor Juhos2012-05-162-1/+26
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31753 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/net5501: switch to 3.3Gabor Juhos2012-05-162-1/+20
| | | | | | Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31752 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: sync 3.3 configsGabor Juhos2012-05-162-17/+16
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31751 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: sync 3.2 configsGabor Juhos2012-05-163-14/+14
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31750 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: sync 2.6.39 configsGabor Juhos2012-05-166-106/+104
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31749 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux: move certain disabled symbols to the generic configsGabor Juhos2012-05-157-44/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * CONFIG_ARCH_DMA_ADDR_T_64BIT * CONFIG_ARCH_HAS_ILOG2_U32 * CONFIG_ARCH_HAS_ILOG2_U64 * CONFIG_ARCH_PHYS_ADDR_T_64BIT * CONFIG_ARCH_SUPPORTS_MSI * CONFIG_GENERIC_CPU_DEVICES * CONFIG_HWMON_DEBUG_CHIP * CONFIG_I2C_PXA_PCI * CONFIG_LEDS_GPIO * CONFIG_MINIX_FS_NATIVE_ENDIAN * CONFIG_MLX4_CORE * CONFIG_POWER_SUPPLY * CONFIG_POWER_SUPPLY_DEBUG * CONFIG_QUOTACTL * CONFIG_SDIO_UART * CONFIG_SENSORS_K10TEMP * CONFIG_SENSORS_SCH56XX_COMMON * CONFIG_SENSORS_VIA_CPUTEMP * CONFIG_SERIO_AMBAKMI * CONFIG_SERIO_I8042 * CONFIG_SERIO_LIBPS2 * CONFIG_SERIO_PCIPS2 * CONFIG_SERIO_RAW * CONFIG_SERIO_SERPORT * CONFIG_SPI_BITBANG * CONFIG_SPI_GPIO git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.3 to 3.3.6Gabor Juhos2012-05-141-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31709 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.3 to 3.3.5Gabor Juhos2012-05-071-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31645 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.3 to 3.3.4Gabor Juhos2012-04-301-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31541 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.3 to 3.3.3Jonas Gorski2012-04-241-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31460 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.2 to 3.2.16Jonas Gorski2012-04-242-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31459 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: restore config-default, it is needed for 2.6.39Gabor Juhos2012-04-231-0/+379
| | | | | | Reported-by: Thomas Heil <heil@terminal-consulting.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31452 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: remove 2.6.32 supportGabor Juhos2012-04-214-502/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31415 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: x86: also update subtarget kernel versionsJonas Gorski2012-04-173-3/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31338 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [geos] bump to Linux v3.3.1Jo-Philipp Wich2012-04-161-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31314 3c298f89-4303-0410-b956-a3cf2f4a3e73
* PATCH: Disable console terminal in Grub for alix2 targetJo-Philipp Wich2012-04-121-1/+1
| | | | | | | | | | | The alix2 target has the VGA console for grub enabled by default. This prevents the grub menu from appearing on bootup. It is disabled by default for the other embedded x86 platforms. This patch corrects that behavior for the alix2 target. Signed-off-by: Adam Gensler <openwrt@kristenandadam.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31270 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] add missing Kernel symbol spotted by buildbotJo-Philipp Wich2012-04-101-4/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31232 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.2 to 3.2.14Jonas Gorski2012-04-091-25/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31222 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] geos: add 'tc' and kmod-sched for bondingFlorian Fainelli2012-03-271-2/+2
| | | | | | | | The Geos2 includes 2 ADSL+ interfaces, and as such it needs to have the TEQL scheduler for bonding. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31094 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Disable keyboard for x86 default config - revoke patch 30966 Jens Muecke2012-03-211-3/+0
| | | | | | | | This was already fixed by commit 30309 and is part of generic x86 target. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31052 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] alix2: add require crypto kmods (#10410)Jo-Philipp Wich2012-03-181-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30980 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Enable keyboard for x86Jens Muecke2012-03-171-0/+3
| | | | | | | | | This is required for qemu like descripted in here http://wiki.openwrt.org/doc/howto/qemu git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30966 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] enable RTC_CLASS for Linux 3.2 and 3.3Jo-Philipp Wich2012-02-252-0/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30717 3c298f89-4303-0410-b956-a3cf2f4a3e73
* config: deprecated symbol CONFIG_LEDS_GPIO_PLATFORMJo-Philipp Wich2012-02-244-2/+2
| | | | | | | | | | | | CONFIG_LEDS_GPIO_PLATFORM went away a while ago. http://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=commit;h=2bcc7ed5b83b0a59c6976476e8788675038fb11b Also, most platforms comment out CONFIG_LEDS_GPIO but not x86 for some reason. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30708 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] Disable by default padding of imagesVasilis Tsiligiannis2012-02-161-1/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30590 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] Allow gzipping of squashfs images with padded jffs2 partitionVasilis Tsiligiannis2012-02-161-0/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30589 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] GZip only ext4 and padded imagesVasilis Tsiligiannis2012-02-162-4/+7
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30588 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 00:59:34 +0000