aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/x86/base-files
Commit message (Collapse)AuthorAgeFilesLines
* Revert "gpio-cdev: add nu801 userspace driver"Christian Lamparter2021-10-101-1/+1
| | | | | | | | | | | This reverts commit f536f5ebddd9c532a08ac4a9be3ef0c02f7bfeb8. As Hauke commented, this causes builder failures on 5.4 kernels. This revert includes changes to the mx100 kernel modules dependency as well as the uci led definitions. Tested-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: add support for Meraki MX100Chris Blake2021-10-103-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit will add support for the Meraki MX100 in OpenWRT. Specs: * CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T * Memory: 4GB DDR3 1600 ECC * Storage: 1GB USB NAND, 1TB SATA HDD * Wireless: None * Wired: 10x 1Gb RJ45, 2x 1Gb SFP UART: The UART header is named CONN11 and is found in the center of the mainboard. The pinout from Pin 1 (marked with a black triangle) to pin 4 is below: Pin 1: VCC Pin 2: TX Pin 3: RX Pin 4: GND Note that VCC is not required for UART on this device. Booting: 1. Flash/burn one of the images from this repo to a flash drive. 2. Take the top off the MX100, and unplug the SATA cable from the HDD. 3. Hook up UART to the MX100, plug in the USB drive, and then power up the device. 4. At the BIOS prompt, quickly press F7 and then scroll to the Save & Exit tab. 5. Scroll down to Boot Override, and select the UEFI entry for your jumpdrive. Note: UEFI booting will fail if the SATA cable for the HDD is plugged in. The issue is explained under the Flashing instructions. Flashing: 1. Ensure the MX100 is powered down, and not plugged into power. 2. Take the top off the MX100, and unplug the SATA cable from the HDD. 3. Using the Mini USB female port found by the SATA port on the motherboard, flash one of the images to the system. Example: `dd if=image of=/dev/sdb conv=fdatasync` where sdb is the USB device for the MX100's NAND. 4. Unplug the Mini USB, hook up UART to the MX100, and then power up the device. 5. At the BIOS prompt, quickly press F7 and then scroll to the Boot tab. 6. Change the boot order and set UEFI: USB DISK 2.0 as first, and USB DISK 2.0 as second. Disable the other boot options. 7. Go to Save & Exit, and then select Save Changes and Reset Note that OpenWRT will fail to boot in UEFI mode when the SATA hard drive is plugged in. To fix this, boot with the SATA disk unplugged and then run the following command: `sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg` Once the above is ran, OpenWRT will boot when the HDD is plugged into SATA. The reason this happens is the UEFI implementation for the MX100 will always set anything on SATA to HD0 instead of the onboard USB storage, so we have to accomidate it since OpenWRT's GRUB does not support detecting a boot disk via UUID. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: add upgrade support to diag.shChris Blake2021-06-101-0/+4
| | | | | | | | | Similar to how this is done in the diag.sh found in the base-files package, we should blink our status LED (if we have one) during the upgrade process. This follows the same blink pattern as seen at ./package/base-files/files/etc/diag.sh#L36 Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: add Roqos Core RC10 ethernet interfacesTomasz Maciej Nowak2021-06-061-0/+3
| | | | | | | | | | | | | | | | | | | eth0 -> single NIC (i211at) eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U) Notes UART is exposed on J4 connector, pinout starting from pin marked 1: 1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC? baud: 115200, parity: none, flow control: none The board is setup by coreboot with UEFI. To enter setup screen hold ESC key on boot. The 5-LED multicolor matrix is attached on first I2C device named "Synopsys DesignWare I2C adapter" at address 0x60. Controlling values are stored in /opt/roqos/etc/rcLED.conf of original firmware. Remember to backup the original firmware, there are no downloadable copies. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* x86/base-files: add support for Sophos SG/XG-105Stan Grishin2021-03-262-0/+11
| | | | | | | This adds detection of the Sophos SG-105 and Sophos XG-105 models and assignment of ethernet ports these models have to LAN/WAN. Signed-off-by: Stan Grishin <stangri@melmac.net>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* x86: add led driver for PC Engines APU1Andreas Eberlein2021-02-203-5/+9
| | | | | | | | | This driver adds the LED support for the PC Engines APU1. This integrates the Linux kernel driver and includes a patch to support newer firmware versions. Also the default LED configuration is updated to use the correct devices. Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
* x86: upgrade: make code comment appear as log linesYousong Zhou2020-11-111-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | The comment content can be useful for readers of both the log and code Previously when dd command "records in/out" messages are not filtered like now with get_image_dd, it's not clear that these messages are for extracting boot sectors. E.g. Before == upgrade: Reading partition table from bootdisk... 37+26 records in 37+26 records out == upgrade: Reading partition table from image... After == upgrade: Reading partition table from bootdisk... == upgrade: Extract boot sector from the image 37+26 records in 37+26 records out == upgrade: Reading partition table from image... Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* x86: upgrade: use get_image_ddYousong Zhou2020-11-111-5/+5
| | | | | | | Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140 Reported-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com> Reviewed-By: Philip Prindeville <philipp@redfish-solutions.com>
* x86: upgrade: use v function for writting logsYousong Zhou2020-11-111-8/+8
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* x86: fix touching bootloader "upgraded" markYousong Zhou2020-11-021-1/+1
| | | | | | | | | | | | | | The mount point is "/tmp/boot", the path in the boot partition is "/boot/grub/upgraded". Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader upgrade") Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade") Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140 Reported-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-164-5/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* x86: fix grub-bios-setup fail during sysupgrade李国2020-04-091-1/+1
| | | | | | | | | | grub-bios-setup requires two images (boot.img and core.img), but they are missing. This make an error during sysupgrade: Upgrading bootloader on /dev/sda... grub-bios-setup: error: cannot open `/tmp/boot/boot/grub/boot.img': No such file or directory. Signed-off-by: 李国 <uxgood.org@gmail.com>
* x86: generate EFI platform bootable images李国2020-03-313-9/+24
| | | | | | | | | | | | | | | | | Add EFI platform bootable images for x86 platforms. These images can also boot from legacy BIOS platform. EFI System Partition need to be fat12/fat16/fat32 (not need to load filesystem drivers), so the first partition of EFI images are not ext4 filesystem any more. GPT partition table has an alternate partition table, we did not generate it. This may cause problems when use these images as qemu disk (kernel can not find rootfs), we pad enough sectors will be ok. Signed-off-by: 李国 <uxgood.org@gmail.com> [part_magic_* refactoring, removed genisoimage checks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: add preinit hook for bootloader upgradeTomasz Maciej Nowak2020-03-012-1/+21
| | | | | | | | | | | | | | | | This commit fills the void for current OpenWrt installations which will be still on old bootloader version even after "x86: add bootloader upgrade on sysupgrade", since it performs bootloader upgrade only on sysupgrade. To keep all OpenWrt deploynents on the same GRUB version, add preinit hook, which will perform upgrade of the bootloader on first boot after sysupgrade. It's temporary solution and should be deleted, when the first release including this hook will no longer be supported by OpenWrt team. We can assume that all installations should be on current bootolader version and from there sysupgrade routine will be sufficient. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: add bootloader upgrade on sysupgradeTomasz Maciej Nowak2020-03-011-0/+24
| | | | | | | | | | | | | | Currently bootloader always stays on the same version as when first written to boot medium (not true if partition layout changed, which will trigger sysupgrade process to write full disk image). That creates inconveniences as it always stays with same features or/and bugs. Users wishing to add support to additional modules or new version, would need to write the whole image, potentially destroying previous system configuration. To fix these, this commit adds additional routine to sysupgrade which upgrades unconditionally the bootloader to the latest state provided by OpenWrt. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-051-1/+1
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: when copying a backup file always specify dest nameRafał Miłecki2019-09-051-1/+1
| | | | | | | $CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz. This change makes code more generic and allows refactoring $CONF_TAR. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: don't hardcode "sysupgrade.tgz" file nameRafał Miłecki2019-09-051-2/+2
| | | | | | | | 1) Add BACKUP_FILE and use it when copying an archive to be restored after sysupgrade (on the next preinit). 2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: pass "save_partitions" option to the "sysupgrade" methodRafał Miłecki2019-08-221-1/+1
| | | | | | | This explicitly lets stage2 know if partitions should be preserved. No more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* x86: fix missing led variable warning during bootPetr Štetiar2019-06-251-0/+2
| | | | | | | | Fixes following warning during the boot: WARNING: Variable 'led' does not exist or is not an array/object Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "base-files: add console to inittab"Alexander Couzens2019-05-251-1/+0
| | | | | | | This reverts commit cde52cb4866fe8cf4a19bb2bb32ff7802e542e19. When using OpenWrt in qemu, the shell is unsuable Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* base-files: add console to inittabPaul Spooren2019-05-211-0/+1
| | | | | | | | | | | When running OpenWrt inside an LXC container no shell is opend as LXC defaults to a virtual /dev/console. This patch allows to enter a shell after starting the container via `lxc-start`, without it is only posible to access a shell on tty1 via `lxc-console`. Signed-off-by: Paul Spooren <mail@aparcar.org>
* x86: make sysupgrade.tgz reachable againTomasz Maciej Nowak2018-12-031-1/+1
| | | | | | | | | Moving binding mount before check for saved sysupgrade configuration made it unreachable. Fix it by moving binding mount after the check. Fixes: f78b2616 (x86: mount writable bootfs) Reported-by: Lucian Cristian <luci@powerneth.ro> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* Revert "x86: add intel microcode entries to grub config"John Crispin2018-11-271-4/+2
| | | | | | This reverts commit 546fced2a23557e95dd34246744c3aa6cad92fe6. Signed-off-by: John Crispin <john@phrozen.org>
* Revert "x86: add amd microcode entries to grub config"John Crispin2018-11-271-0/+12
| | | | | | This reverts commit a822283c7e56bb3b409712e0eb9af5a91aac247d. Signed-off-by: John Crispin <john@phrozen.org>
* x86: add amd microcode entries to grub configTomasz Maciej Nowak2018-11-261-12/+0
| | | | | | | | Create initrd enries for x86 images, that'll load amd microcode as early as possible. Also remove the preinit script responsible for late load of microcode. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: add intel microcode entries to grub configTomasz Maciej Nowak2018-11-261-2/+4
| | | | | | | | | Create initrd enries for x86 images, that'll load intel microcode as early as possible. To achieve that the test module for grub is enabled which provides shell-like conditionals. Also restrict the late load of microcode to AMD processors. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: mount writable bootfsTomasz Maciej Nowak2018-11-261-8/+4
| | | | | | | Mount boot file system with rw option to allow installation of packages which install files to /boot directory. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: Add APU3 reference to x86 board.dKristian Evensen2018-05-182-2/+2
| | | | | | | | | | | There is a new APU-model available, APU3. The device is configured in the same way as the APU1 and APU2, so the same LED/network setup can be used. I considered changing the case to pc-engines-apu*, but I chose to follow the existing pattern and add the full board name. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* x86: add preinit hook to reload microcodeZoltan HERPAI2018-02-111-0/+10
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* x86: preinit: use board_name on Sm Super ServersPhilip Prindeville2018-01-041-1/+8
| | | | | | | | | Supermicro puts "Super Server" into their product_name DMI value for a whole slew of products, making this value about as useful as not having been filled in at all. Instead, fall back on the board_name instead. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* x86: preinit: make name rewrite into reusable functionPhilip Prindeville2018-01-041-6/+10
| | | | | | | | There might be other places (such as vendor-supplied preinit scripts) where we wish to take a DMI name and clean it up in a consistent way, so make the sed command into a function. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* treewide: use only board_name function to get nameMathias Kresin2017-07-152-6/+2
| | | | | | | | | | | | Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree compatible string directly. Always use the board_name function to get the board name. The admswconfig package still reads /proc/cpuinfo directly. The code looks somehow broken and the whole adm5120 which uses this package looks unmaintained. Leave it as it is for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: populate boardname and model earlierMathias Kresin2017-07-151-0/+0
| | | | | | | | | | | | | For targets using the generic board detection and board specific settings in diag.sh, the board name is still unset at the time the set_state() provided by diag.sh is called by 10_indicate_preinit. Change the execution order to ensure the boardname is populated before required the first time. Do the target specific board detection as early as possible, directly followed by the generic one to allow a seamless switch to the generic function for populating /tmp/sysinfo/. Signed-off-by: Mathias Kresin <dev@kresin.me>
* Add missing APU1 reference to x86 board.dKristian Evensen2017-06-062-2/+2
| | | | | | | | | | | | x86 board.d only contains a case for the APU2, not the APU1. This causes, for example, network configuration not to be created correctly. Even though the APU1 seems to reaching EOL, there a still a lot of them out there. The APU1 and APU2 is configured in the same way and this patch should also be considered for stable, as the error also exists there. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* x86: sysupgrade: explicitly rescan disk after writing partition tableMatthias Schiffer2017-05-291-0/+6
| | | | | | | This should ensure that the kernel partition can be mounted in platform_copy_config when its size has changed. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* x86: sysupgrade: refactor platform_do_upgradeMatthias Schiffer2017-05-291-33/+36
| | | | | | | By returning early when no upgrade device can be found and handling the SAVE_PARTITIONS=0 case differently, we can get rid of two levels of if. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* x86: sysupgrade: move partition table change check to platform_check_imageMatthias Schiffer2017-05-291-4/+25
| | | | | | | The staged sysupgrade will prevent us from using ask_bool in platform_do_upgrade; therefore, the check is moved to platform_check_image. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* x86: keep /boot mounted for kexecDaniel Golle2017-05-051-4/+7
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* x86: Add board configs for the PC Engines APU2Chris Blake2017-02-152-0/+8
| | | | | | | | This adds the default LED and network settings for the PC Engines APU2 when running under the x86 target. [dwmw2: Change Ethernet port setup] Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: Enable DIAG LED on GeosDavid Woodhouse2017-02-152-1/+79
| | | | | | | | | Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's do it by using the LED configuration instead of hard-coding it for each board type. And try using /bin/board_detect to do the default behaviour, on the first boot where the config hasn't yet been generated. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* x86: Move Traverse Geos configs into x86 base-filesChris Blake2017-02-152-0/+45
| | | | | | | | | | This change moves the files in 657418d to the root of the x86 target. This is done in preperation for adding more devices under other subtargets. CC: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: fix sysupgrades on disks with 4k block sizeFelix Fietkau2017-01-251-9/+2
| | | | | | | Even when the disk uses 4k blocks, the partition table still uses units of 512 byte sectors. Always use ibs=512 for the offsets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86/generic: add xen DomU supportFelix Fietkau2017-01-161-0/+1
| | | | | | Copy the relevant config options from the xen_domu subtarget Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: export x86 platform upgrade functions to common.shYousong Zhou2017-01-052-96/+5
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* x86: move sysupgrade.tgz only if it existsYousong Zhou2017-01-051-3/+6
| | | | | | | | To squash error messages at boot time mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* x86: use sysfs DMI information to populate sysinfoJo-Philipp Wich2016-06-061-0/+28
| | | | | | | | | | | | | | | | | | Use the DMI data available in sysfs to extract manufacturer and model info and write it to /tmp/sysinfo/. The data will be picked up by board_detect and can be used by e.g. LuCI to display a more appropriate model description. On an APU board the files will contain the following values: # cat /tmp/sysinfo/model PC Engines APU # cat /tmp/sysinfo/board_name pc-engines-apu Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* x86: generalize partition discovery for sysupgradeJo-Philipp Wich2016-05-242-25/+54
| | | | | | | | | | | | | | | Generalize the partition discovery in sysupgrade in order to fix sysupgrade and config backup/recovery on MMC block devices which use a different naming scheme compared to mtdblock or sd* devices. The change also adds the find applet to the ramdisk utilities so that upgrade code can rely on it. The commit is based on the initial submission by Russell Senior at http://patchwork.ozlabs.org/patch/625440/ . Signed-off-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* image / basefiles: make console password configurableJohn Crispin2016-04-181-2/+2
| | | | | Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> Signed-off-by: John Crispin <john@phrozen.org>