aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/sunxi/image
Commit message (Collapse)AuthorAgeFilesLines
* sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmwareHauke Mehrtens2021-12-271-4/+4
| | | | | | | | The firmware for the rtl8723bs chip is now included in the rtl8723bu-firmware package. Fixes: 397dfe4a97e6 ("linux-firmware: Update to version 20121216") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: update nanopi neo air that use brcmfmac43430a0Michel Promonet2021-12-021-1/+1
| | | | | | | | Update wifi firmware used for nanopi neo air, with cypress-firmware-43430-sdio there is no wifi detected, as brcmfmac-firmware-43430a0-sdio allow to acces to wifi. Signed-off-by: Michel Promonet <michel.promonet@free.fr>
* sunxi: remove kmod-rtc-sunxi for unsupported devicesChukun Pan2021-11-291-10/+10
| | | | | | | | | | | | | | | | From driver source: { .compatible = "allwinner,sun4i-a10-rtc", .data = &data_year_param[0] }, { .compatible = "allwinner,sun7i-a20-rtc", .data = &data_year_param[1] }, The rtc-sunxi module only supports allwinner a10 and a20 SoCs, other SoCs in the cortexa7 and cortexa53 subtarget using the CONFIG_RTC_DRV_SUN6I driver which is compiled into the kernel binary, so remove this package for these unsupported devices. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* sunxi: add support for FriendlyARM NanoPi R1S H5Chukun Pan2021-10-301-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: Allwinner H5, Quad-core Cortex-A53 DDR3 RAM: 512MB Network: 10/100/1000M Ethernet x 2 USB Host: Type-A x 1 MicroSD Slot x 1 MicroUSB: for power input Debug Serial Port: 3Pin pin-header LED: WAN, LAN, SYS KEY: Reset Power Supply: DC 5V/2A Installation: Write the image to SD Card with dd. Note: 1. OpenWrt currently does not support LED_FUNCTION, change back to the previous practice (Consistent with NanoPi R1). 2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to change the phy-mode from rgmii to rgmii-id. So set phy-mode for 5.4 and 5.10 respectively. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* sunxi: bring up DSA b53 switch on Lamobo R1Daniel Golle2021-09-151-1/+5
| | | | | | | | | | | | | | | | | | | | | Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi BPi-R1 board which comes with such a switch IC. Remove old swconfig driver from target kernel config as the only board using it is now supported by the DSA driver. No changes to device tree are needed as upstream DTS already got a DSA switch definition and we are just using that upstream source. Update default network config of the Lamobo R1 to create lan bridge with all 4 lan ports. Introduce DEVICE_COMPAT_VERSION for the board to inform users about having the re-create their network configuration and add device alias as Bananapi BPi-R1 while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* linux-firmware: update to version 20210315 and trim down broadcom FWJosef Schlehofer2021-06-061-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In there linux-firmware repository located in kernel, there were removed old broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability (CVE-2019-15126), because Cypress released new versions and superseded by it. In OpenWrt, there is Makefile for cypress-firmware, which already provides the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio provides brcmfmac-firmware-43455-sdio [2]. Changelog between 2020118 and 20210315: 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 [1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c [2] https://github.com/openwrt/openwrt/blob/eeda8652f1655d4f9c11e9c9f51ddcd3377d119a/package/firmware/cypress-firmware/Makefile#L124 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* sunxi: add support for Banana Pi M2 BerryZoltan HERPAI2021-04-121-0/+10
| | | | | | | | | | | | | | | | | | CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz Memory: 1GB DDR3 Storage: SDcard, native SATA Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT USB: 4x USB 2.0 Installation: Use the standard sunxi installation to an SD-card. While the board is very similar to the M2 Ultra board (the V40 is the automotive version of the R40), as both the u-boot and kernel supports them separately, and some pins are different, let's add a separate device spec. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: add support for H6 boards and OrangePiOnePlusZoltan HERPAI2021-04-111-2/+15
| | | | | | | | | | | | | | | | | | | | Specifications: SoC Allwinner H6 @ 1.8 Ghz DRAM 1Gb LPDDR3 Power DC 5V @ 3A Video HDMI (Type 2.0A - full) Audio HDMI, on-board microphone Network 10/100/1000Mbps Ethernet (Realtek RTL8211) Storage microSD USB 1 USB2.0 Host, 1 USB2.0 OTG Debug Serial UART Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: enable wifi module on Pine64 boardsZoltan HERPAI2021-03-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi module, carrying an RTL8723BS. The wifi part is connected via SDIO, the BT part is connected via UART. The BT part requires additional code changes in the drivers so we'll skip that until 5.10. Aside from a DTS patch to enable the wifi module, add the required packages into the device definitions. [ 8.996970] RTL8723BS: module init start [ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40 [ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40 [ 9.014785] pnetdev = 000000009bdd5000 [ 9.047780] RTL8723BS: rtw_ndev_init(wlan0) [ 9.053349] RTL8723BS: module init ret =0 root@OpenWrt:/# iw list Wiphy phy0 wiphy index: 0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * monitor Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (no IR) * 2472 MHz [13] (20.0 dBm) (no IR) * 2484 MHz [14] (20.0 dBm) (no IR) Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* target: use SPDX license identifiers on scriptsAdrian Schmutzler2021-02-101-4/+1
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-104-16/+5
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: add support for linksprite pcDuino3 nano boardJiang Yongquan2021-01-271-0/+8
| | | | | | | | | | | | | | | | | | Specifications: - SoC: Allwinner A20 @ 1Ghz - DRAM: 1GiB DDR3 @ 408MHz (K4B4G1646Q-HYK0) - NAND: 4GB MLC NAND (H27UBG8T2BTR-BC) - Ethernet: 10/100/1000Mbps Ethernet (Realtek RTL8211E) Flash instructions: dd if=openwrt-sunxi-cortexa7-linksprite_pcduino3-nano-ext4-sdcard.img of=/dev/sdX Signed-off-by: Jiang Yongquan <woxwchc@foxmail.com> [Remove CONFIG_REALTEK_PHY from sunxi/cortexa53 config] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: drop empty kmod-ledtrig-* packagesSungbo Eo2021-01-151-9/+8
| | | | | | | | | | | | | | The following four led triggers are enabled in generic config. * kmod-ledtrig-default-on * kmod-ledtrig-heartbeat * kmod-ledtrig-netdev * kmod-ledtrig-timer Drop the packages and remove them from DEVICE_PACKAGES. There's no other package depending on them in this repo. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* sunxi: add support for Libre Computer ALL-H3-CC H5Roman Kuzmitskii2020-11-121-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: Allwinner H5, Quad-core Cortex-A53 Up to 1GHz - DDR3 RAM: 2GB - Network: 10/100M Ethernet x 1 - IR: x1 (Receive) - USB (Host) Type-A x3 - USB (OTG) Type-A x1 - MicroSD Slot x 1 - eMMC Slot x1 - MicroUSB power input - GPIO 40pin header - UART 3pin header - Leds: - librecomputer:blue:status - librecomputer:green:pwr - Buttons: - uboot button (used to enter fel mode) - power button (can trigger power on) - Power Supply via MicroUSB or GPIO 5V/2A Installation: - Write the image to SD Card with dd - Boot from the SD Card Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com> [Fixed Signed-off-by] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: add support for FriendlyARM NanoPi R1Jayantajit Gogoi2020-10-181-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz - DDR3 RAM: 512MB/1GB - Network: 10/100/1000M Ethernet x 1， 10/100M Ethernet x 1 - WiFi: 802.11b/g/n, with SMA antenna interface - USB Host: Type-A x2 - MicroSD Slot x 1 - MicroUSB: for OTG and power input - Debug Serial Port: 3Pin 2.54mm pitch pin-header - LED: nanopi:red:status nanopi:green:wan nanopi:green:lan - KEY: reset - Power Supply: DC 5V/2A Installation: - Write the image to SD Card with dd - Boot NanoPi from the SD Card Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
* sunxi: use wpad-basic-wolfssl for Sinovoip Banana Pi M2 UltraAdrian Schmutzler2020-10-151-1/+1
| | | | | | | | | The idea of commit a14f5bb4bd26 was to use wpad-basic-wolfssl consistently throughout the whole trunk, so use it here as well. Fixes: 50fdddae05f1 ("BPi-M2U kernel modules for onboard WiFi") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: Correct manufacturer name to SinovoipHal Martin2020-10-111-3/+4
| | | | | | | Sinovoip is the manufacturer of the BPi-M2U: http://www.banana-pi.org/m2u.html Signed-off-by: Hal Martin <hal.martin@gmail.com>
* sunxi: BPi-M2U kernel modules for onboard WiFiHal Martin2020-10-111-1/+2
| | | | Signed-off-by: Hal Martin <hal.martin@gmail.com>
* sunxi: add support for FriendlyArm ZeropiArturas Moskvinas2020-10-111-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specification CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz DDR3 RAM: 256MB/512MB Connectivity: 10/100/1000Mbps Ethernet USB Host: Type-A x 1 MicroSD Slot x 1 MicroUSB: for power input only Debug Serial Port: 4Pin, 2.54 mm pitch pin header Power Supply: DC 5V/2A PCB Dimension: 40 x 40 x 1.2mm Installation: Burn the image file to an SD Card with dd or any image burning tool Boot ZeroPi from the SD Card The following features are working and tested: Ethernet port 10/100/1000M Ethernet Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi) Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-4/+4
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: make dependency on kmod-usb-net selectiveAdrian Schmutzler2020-08-101-1/+1
| | | | | | | | A bunch of kernel modules depends on kmod-usb-net, but does not select it. Make AddDepends/usb-net selective, so we can drop some redundant +kmod-usb-net definitions for DEVICE_PACKAGES. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-114-11/+1
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: a53: add support for Olimex A64-Olinuxino eMMCPetr Štetiar2020-03-281-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit) RAM: 1GB or 2GB RAM DDR3L @ 672Mhz Flash: 0/4/16GB eMMC flash memory for storage and boot MicroSD card connector for cards up to 32GB Debug: serial UART debug header with 0.1" pins Wired connectivity: 10/100/1000Mbps GbE Ethernet Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and Bluetooth 4.0 module with built-in antenna (only available in the A64-OLinuXino-1G4GW) Flashing instructions: Standard sunxi SD card installation procedure - copy eMMC image to SD card, insert in into SD card slot on the device and boot. You should see something like following if the eMMC is detected correctly: mmcblk2: mmc2:0001 P1XXXX 3.60 GiB mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB Then flash SD card eMMC image straight into the mmcblk2 device: dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2 It also possible to boot from boot0 partition[1]: 1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40 otherwise the U-Boot will get stuck in bootloop 2. Configure eMMC to boot from boot0 partition inside U-Boot: mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0 3. echo 0 > /sys/block/mmcblk2boot0/force_ro 4. Write U-Boot from offset 0 (not offset 8k as with SD card) into boot0 partition dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0 Known issues: Wireless doesn't work properly via netifd. 1. https://linux-sunxi.org/index.php?title=Bootable_eMMC Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: add support for Olimex A64-OlinuxinoPetr Štetiar2020-03-281-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit) RAM: 1GB or 2GB RAM DDR3L @ 672Mhz Flash: 0/4/16GB eMMC flash memory for storage and boot MicroSD card connector for cards up to 32GB Debug: serial UART debug header with 0.1" pins Wired connectivity: 10/100/1000Mbps GbE Ethernet Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and Bluetooth 4.0 module with built-in antenna (only available in the A64-OLinuXino-1G4GW) Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert in into SD card slot on the device and boot. Known issues: Wireless doesn't work properly via netifd. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: image: make it DRYPetr Štetiar2020-03-281-24/+22
| | | | | | Replace same copy&pasted lines with the appropriate reusable bits. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-1/+1
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: make kmod-ata-core selected by dependent modulesupstreamless-old-masterSungbo Eo2020-03-112-13/+13
| | | | | | | | | | | | | | | | Currently kmod-ata-* will not get into images unless kmod-ata-core is added to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to "select", we do not have the issue anymore. Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES and similar variables, as it is now pulled by dependent modules such as: - kmod-ata-ahci - kmod-ata-ahci-mtk - kmod-ata-sunxi While at it, use AddDepends/ata for kmod-ata-pdc202xx-old. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* sunxi: remove SUNXI_UBOOT from DEVICE_VARSSungbo Eo2020-03-111-1/+1
| | | | | | | All SUNXI_UBOOT usages were removed in e018c4d7ab8b ("uboot-sunxi: clean up, switch to u-boot.mk"). Now drop the variable completely. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* sunxi: tidy up and sort alphabetically in image MakefilesAdrian Schmutzler2020-01-234-197/+135
| | | | | | | | | | This tidies up the image Makefiles for the sunxi target by: - Move the if-condition for the subtarget to the parent Makefile - Remove lots of unnecessary empty lines - Sort device definitions alphabetically - Harmonize line wrapping for DEVICE_PACKAGES Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: gen_sunxi_sdcard_img.sh: switch to /bin/shRosen Penev2019-12-311-1/+1
| | | | | | | | This has nothing that needs bash. Signed-off-by: Rosen Penev <rosenp@gmail.com> [add prefix to commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: rename SUNXI_SOC to SOCAdrian Schmutzler2019-12-204-38/+37
| | | | | | | This replaces SUNXI_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: add support for FriendlyARM Nano PI NEO Air dev boardRoman Bazalevsky2019-12-131-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: Allwinner H3 upto 1.2GHz 512MB DDR3 RAM 8GB on-board eMMC - mountable, can be used as boot with custom boot.scr microSD-card slot WiFi 802.11n (AP6212A) - working Bluetooth (AP6212A) - not working for now Micro-USB OTG + 2*USB headers UART 3.3V - working GPIO/I2C/SPI 2.54mm headers Standard sunxi SD-card installation procedure - copy image to SD card, insert in into slot and boot. First time you will need UART adapter to enable on-board wireless (or just build custom image with enabled WiFi). To boot from eMMC: - boot from SD - copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2) - mount eMMC boot partition and replace boot script on it - unmount, reboot To use i2c, spi and more uarts - replace dtb on boot partition with fixed one (use dtc or fdt-tools). Signed-off-by: Roman Bazalevsky <rvb@rvb.name> [rebase onto device name consolidation patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: construct DTS name from device node name and SOCAdrian Schmutzler2019-12-134-35/+45
| | | | | | | | | The device part in the SUNXI_DTS variable always corresponds to device node name. This is another redundancy that can be removed by calculating the DTS name from a newly introduced SUNXI_SOC variable and the node name. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: use vendor_device scheme for device definitionsAdrian Schmutzler2019-12-134-99/+69
| | | | | | | | | | | | This changes device definition to resemble the vendor_device scheme already present for the majority of device compatible strings. By doing this, we achieve several advantages at once: - Image names and node names are more consistent with other targets. - SUPPORTED_DEVICES can be set automatically for all but two cases. - Image names and node names are in line with DEVICE_TITLEs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: replace backticks by $(...) in gen_*_img.sh scriptsAdrian Schmutzler2019-09-291-1/+1
| | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [decapitalized patch subject at submitter's request] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: Add support for Banana Pi M2 UltraHal Martin2019-09-211-0/+10
| | | | | | | | | | | | | | | | | | CPU: Allwinner R40 Quad-Core Cortex-A7 @ 1.2GHz GPU: Mali 400 MP2 Memory: 2GB DDR3 onboard (shared with GPU) Onboard: Storage microSD card slot Onboard: Storage 8GB eMMC Onboard: Network 10/100/1000M Ethernet RJ45 Onboard: Network WiFi 802.11b/g/n 1x1 (AMPAK AP6212; brcmfmac) Onboard header: SPI, I2C, GPIO, UART USB: Two USB 2.0 Host, One USB 2.0 OTG Known issues: - WiFi doesn't work - eMMC not supported Signed-off-by: Hal Martin <hal.martin@gmail.com>
* sunxi: convert to multi-variable device titleLuis Araneda2019-07-103-33/+67
| | | | | | | Use data from the linux-sunxi community wiki to fill-in missing device information Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* sunxi: add support for Orange Pi PC PlusAleksander Jan Bajkowski2019-03-091-0/+10
| | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Storage 8 GB eMMC Onboard: Network 10/100M Ethernet RJ45 Onboard: Network WiFi 802.11 b/g/n (Realtek RTL8189FTV) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG Known issues: -Wifi diesn't work Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* sunxi: add support for Orange Pi OneAleksander Jan Bajkowski2019-02-261-0/+10
| | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 512MB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard header: SPI, I2C, GPIO, UART USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* sunxi: add support for Sinovoip Banana Pi M2 PlusPawel Dembicki2019-02-171-1/+11
| | | | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E) Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG Untested: Audio, Video Not working: Bluetooth Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-2/+2
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* sunxi: add support for Orange Pi ZeroJulian Haupt2018-10-071-0/+10
| | | | Signed-off-by: Julian Haupt <julian.haupt@hauptmedia.de>
* sunxi: build image/uboot for the NanoPi NEO2Jasper Scholte2018-09-221-0/+10
| | | | | | | | The NanoPi NEO2 is a small Allwinner H5 based board available with different DRAM configurations. This board is very similar to the NanoPi NEO PLUS2 Signed-off-by: Jasper Scholte <NightNL@outlook.com>
* sunxi: Added support for Xunlong Orange Pi PC2Antonio Silverio2018-08-091-0/+10
| | | | | | | | | | | | | | | | CPU: H5 High Performance Quad-core 64-bit Cortex-A53 GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL Memory: 1GB DDR3 (shared with GPU) Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB) Onboard Network: 1000M/100M Ethernet RJ45 USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode role by default in DTS Buttons: Power Button(SW4) Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI.. Signed-off-by: Antonio Silverio <menion@gmail.com>
* sunxi: add build for sopineFan Fan2018-03-231-0/+10
| | | | | | This will generate image for Pine64 Sopine board. Signed-off-by: Fan Fan <fkpwolf@gmail.com>
* sunxi: Add support for Xunlong Orange Pi PCVitalij Alshevsky2018-02-261-0/+10
| | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.3 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Network 10/100M Ethernet RJ45 Onboard header pinout: SPI, I2C, 1-WIRE USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG Buttons: Power Button(SW4) Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI.. Signed-off-by: Vitalij Alshevsky <v_alshevsky@tut.by>
* sunxi: Add Xunlong Orange Pi Zero PlusHauke Mehrtens2018-02-171-0/+11
| | | | | | | This is based on a patch from armbian: https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for NanoPi NEO Plus2 boardAntony Antony2018-02-171-0/+10
| | | | | | | | | | | | | | arm64: allwinner: h5: NanoPi NEO Plus2 DT support Add initial DT for NanoPi NEO Plus2 by FriendlyARM - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU - 1 GB DDR3 RAM - 8GB eMMC flash (Samsung KLM8G1WEPD-B031) - micro SD card slot - Gigabit Ethernet (external RTL8211E-VB-CG chip) - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module) - 2x USB 2.0 host ports & 2x USB via headers Signed-off-by: Antony Antony <antony@phenome.org>
* sunxi: add support for NanoPi M1 Plus boardLuis Araneda2017-11-171-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Backported devicetree from Kernel 4.13 with some additions to enable Ethernet and WiFi module The following features are working: - Ethernet - WiFi - eMMC and microSD slot - USB ports The following features are not working: * Bluetooth NanoPi M1 Plus key features - SoC: Allwinner H3, Quad-core Cortex-A7@1.2GHz - RAM: 1GB DDR3 - eMMC: 8GB - microSD slot - Ethernet 10/100/1000M - Wifi: AP6212 Signed-off-by: Luis Araneda <luaraneda@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 01:40:23 +0000