aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/rockchip/armv8
Commit message (Collapse)AuthorAgeFilesLines
* rockchip: remove unused config symbolsDavid Bauer2020-11-041-2/+0
| | | | | | | | Remove MDIO and I2C bitbangig support from the kernel. These functionalities are currently not used by any board in the target. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: clean up XATTR config symbolsPaul Spooren2020-10-091-1/+0
| | | | | | | | | | | | | Extended attributes are required for overlayfs and have hence been long ago enabled for jffs2, but should be enabled unconditionally for all other filesystems which may potentially serve as overlayfs' upper directory. Previously it was inconsistently added in multiple targets. Add symbols to generic kernel config and remove all *_XATTR symbols from target configs. Signed-off-by: Paul Spooren <mail@aparcar.org> [keep things as they are for squashfs, improve commit message] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* rockchip: enable Realtek PHY supportDavid Bauer2020-10-031-0/+1
| | | | | | | The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the Realtek specific PHY driver to correctly configure internal delays. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: remove useless echo in 40-net-smp-affinityAdrian Schmutzler2020-08-171-1/+1
| | | | | | The command in the $() brackets will already provide the same output. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Move CONFIG_IONIC to generic kernel configHauke Mehrtens2020-08-101-1/+0
| | | | | | | It is deactivated everywhere, just set this in the generic config. Acked-by: Yousong Zhou <yszhou4tech@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rockchip: enable rockchip-thermalDavid Bauer2020-07-291-1/+1
| | | | | | | | | Enable the rockchip-thermal driver to allow reading the temperature of the SoC. Tested on NanoPi R2S Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: distribute net interruptsDavid Bauer2020-07-281-0/+30
| | | | | | | | | | | | This adds a hotplug script for distributing interrupts of eth0 and eth1 across different cores. Otherwise the forwarding performance between eth0 and eth1 is severely affected. The existing SMP distribution mechanic in OpenWrt can't be used here, as the actual device IRQ has to be moved to dedicated cores. In case of eth1, this is in fact the USB3 controller. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: add NanoPi R2S supportDavid Bauer2020-07-283-6/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3328 ARM64 (4 cores) 1GB DDR4 RAM 2x 1000 Base-T 3 LEDs (LAN / WAN / SYS) 1 Button (Reset) Micro-SD slot USB 2.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card using dd. MAC-address ----------- The vendor code supports reading a MAC address from an EEPROM connected via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC address in binary at offset 0xfa. However, my two units didn't come with such an EEPROM soldered on. The EEPROM should be placed between the SoC and the GPIO pins on the board. (U10) Generating rendom MAC addresses works around this issue. Otherwise, all boards running the same image have identical MAC addresses. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: don't disable timer LED triggerDavid Bauer2020-07-131-1/+0
| | | | | | | | The timer LED trigger is enabled in all targets (except for lantiq xway-legacy). It's necessary for the OpenWrt preinit LED pattern to work. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: use downstream GPIO button implementationDavid Bauer2020-07-131-1/+0
| | | | | | | | Use the OpenWrt netlink GPIO button implementation to forward button presses to procd. This is necessary to make failsafe-mode access using a button possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: add support for Pine64 RockPro64Tobias Mädel2020-04-205-0/+643
This adds the new rockchip target and support for RockPro64 RK3399 Flash: 16 MiB SPI NOR RAM: 2 GiB/4 GiB LPDDR4 SoC: RK3399 USB: 2x USB 2.0, 1x USB 3.0, 1x USB-C Ethernet: 1x GbE PCIe: PCIe 2.0, 4 lanes Storage: eMMC or SD card Optional SDIO wifi/bt module The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector, 6 ARM64 cores (4 little, 2 big), plenty of RAM and storage. By default the single Gigabit-Ethernet port is configured as the LAN port. Installation of the firware is possible by dd'ing the image to an SD card or the eMMC flash. Serial: 3v3 1500000 8n1 U-boot is build from the mainline tree and integrated into the images. Required ATF to build u-boot is downloaded from a CI build bot. Signed-off-by: Tobias Mädel <t.maedel@alfeld.de> Tested-by: Tobias Schramm <t.schramm@manjaro.org>