| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
| |
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL930x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL839x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL838x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
| |
Increase the maximum ring buffer length in order to improve
performance on RTL839x devices.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
|
| |
On RTL83xx enable learning of the MAC source address of the CPU port
from outgoing packets. Add documentation on bit fields. On RTL93xx
enable port-mask usage and the use of internal priority, these
SoCs automatically learn the MAC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
Remove the storm control and attack warnings from the IRQ handler
of the Ethernet driver. There was no consequence to the detection
and the kernel can also handle at least the attacks itself.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
| |
This enlarges the size of the TX ring buffer, which prevents warnings
when the buffer runs out of space.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.
To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
|
|
|
|
|
|
|
| |
Deleted (upstreamed):
bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
| |
Patches automatically refreshed.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
|
| |
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On the devices with PoE support, the secondary UART (uart1) on the SoC
is used to communicate between the SoC and controller.
Enable the secondary UART on the following devices:
- D-Link DGS-1210-10P
- Netgear GS110TPP v1
- Netgear GS310TP v1
- ZyXEL GS1900-8HP v1/v2
- ZyXEL GS1900-10HP
- ZyXEL GS1900-24HP v2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
| |
Use physical addresses instead of virtual address in dts files.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
| |
The new backported GPIO driver supports interrupt, so use gpio-keys
instead of gpio-keys-polled for keys connected to the internal GPIO
controller.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch includes the following changes:
- adjust mapping for the new driver
- GPIO 24 -> GPIO 0
- GPIO 47 -> GPIO 0 (+ disabling system LED)
- disable pins in the invalid range
(out of the range 0-31 of the new driver)
- are these pins on the external RTL8231 (&gpio1)?
- GPIO 67 (-> GPIO 3 on &gpio1?)
- GPIO 94 (-> GPIO 30 on &gpio1?)
- drop "indirect-access-bus-id" property from gpio0 node in device dts
files
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
dsa_to_port function in 5.10 returns dsa_port from the port list in
dsa_switch_tree, but the tree is built when the switch is registered
by dsa_register_switch and it's null in rtl83xx_mdio_probe.
So, we need to use dsa_to_port after the registration of the switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
| |
This patch adds a pinctrl-single pinmux node to allow disabling system
LED and enabling GPIO 0 (old driver: GPIO 24).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch fixes the following errors when compiling:
- dsa_switch_alloc is removed[1]
- a parameter "enum dsa_tag_protocol mprot" is added to dsa_tag_protocol
in dsa_switch_ops (include/net/dsa.h)
- several paramters are added to "phylink_mac_link_up" in dsa_switch_ops
(include/net/dsa.h)
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "struct switchdev_trans *trans" is added to
port_vlan_filtering in dsa_switch_ops (include/net/dsa.h)
[1]: https://lore.kernel.org/lkml/20191020031941.3805884-17-vivien.didelot@gmail.com/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch fixes the following errors when compiling:
- "unsigned int txqueue" is added as an additional parameter of
ndo_tx_timeout in net_device_ops (include/linux/netdevice.h)
- "mac_link_state" in phylink_mac_ops (include/linux/phylink.h)
is renamed to "mac_pcs_get_state" and changed the return value
to void from int
- several parameters are added to "mac_link_up" in phylink_mac_ops
(include/linux/phylink.h) and the order of the parameters is
changed
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "phy_interface_t *interface" is added to of_get_phy_mode
(drivers/of/of_net.c) and returns the state instead of phy mode
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
| |
Add a "soc" node as a simple-bus to rtl838x.dtsi and rtl930x.dtsi.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the
following backported drivers:
- gpio-realtek-otto (5.13)
- spi-realtek-rtl (5.12)
- irq-realtek-rtl (5.12)
And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10.
Currently, the upstreamed driver doesn't support the GPIO controller on
RTL930x SoC.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
the following changes are included in this patch:
- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.
The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
This patch adjusts config-5.10 by running kernel_menuconfig.
Note:
- disable psb6970 phy driver (unused in realtek target?)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
| |
This patch refresh all patches in patches-5.10/ to adjust for Kernel
5.10.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
| |
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.
platform-$(CONFIG_RTL838X) += rtl838x/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
| |
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In Kernel 5.10, "help" must be used instead of "---help---".
this patch fixes the following errors:
drivers/net/dsa/rtl83xx/Kconfig:7: syntax errorgit
drivers/net/dsa/rtl83xx/Kconfig:6: unknown statement "---help---"
drivers/net/dsa/rtl83xx/Kconfig:7:warning: ignoring unsupported character '.'
drivers/net/dsa/rtl83xx/Kconfig:7: unknown statement "This"
drivers/net/ethernet/Kconfig:170: syntax error
drivers/net/ethernet/Kconfig:169: unknown statement "---help---"
drivers/net/ethernet/Kconfig:170:warning: ignoring unsupported character '.'
drivers/net/ethernet/Kconfig:170: unknown statement "Say"
drivers/net/phy/Kconfig:331: syntax error
drivers/net/phy/Kconfig:330: unknown statement "---help---"
drivers/net/phy/Kconfig:331: unknown statement "Supports"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
| |
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
| |
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch backports "gpio-realtek-otto" driver to Kernel 5.10.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Note: GPIO mapping is changed in the upstreamed driver.
old - new
24 - 0
25 - 1
26 - 2
27 - 3
28 - 4
29 - 5
30 - 6
31 - 7
16 - 8
17 - 9
18 - 10
19 - 11
20 - 12
21 - 13
22 - 14
23 - 15
8 - 16
9 - 17
10 - 18
11 - 19
12 - 20
13 - 21
14 - 22
15 - 23
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.
And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
| |
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
| |
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch copies the following files from 5.4 to 5.10:
- config-5.4 -> config-5.10
- files-5.4/ -> files-5.10/
- patches-5.4/ -> patches-5.10/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
| |
A superflus ')' character has slipped into commit 91a52f22a1. Remove it
to fix build.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
| |
This reverts commit b7ee0786b56d1088c195fe7c1cdb1ad7d20c9245.
With the previous commit "realtek: remove rtl83xx vlan 1 special cases"
this is no longer required.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
|
|
|
|
|
|
|
|
|
|
|
|
| |
On reset, the PVID of all ports is set to 1; if this is reset to 0,
the special cases for VLAN 1 are no longer required.
port_vlan_add is called with vid=0 when the DSA port interfaces are
enabled with no VLAN; previously the VLAN was not configured in this
case, relying on VLAN 1 being present, but with the PVID set to 0,
configuring VLAN 0 as normal works as expected.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
|
|
|
|
|
|
|
|
|
|
| |
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is
configured. Do not use the standard failsafe configuration for DSA
accessing the default port directly, but configure a switch on the lan1
interface instead.
This will add the VLAN ID 1 configuration to the switch:
$ bridge vlan show
port vlan-id
lan1 1 PVID Egress Untagged
switch 1 PVID Egress Untagged
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes the buffer and packet length calculations for Ethernet TX on
the RTL8380 SoC when CRC calculation offload is enabled.
CRC-offload is always done by the SoC, but additional CRC
calculation was previously done also by the kernel.
It also fixes detection of the DSA tag for packets on RTL8390
SoCs for ports > 28.
v2 has correct whitespace
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
|
|
|
|
|
|
|
| |
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
|
| |
This adds the CPU port to the unknown multicast flooding port mask,
which fixes the VLAN issues introduced by the multicast group patches
Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3]
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
|