aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/realtek
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.10 to 5.10.119John Audia2022-06-071-1/+1
| | | | | | | | | | | Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in. Patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800, x86/64 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit cd634afe6cb6565eb6865931c8d73d97cab3600a)
* realtek: add gpio-restart for D-Link DGS-1210-28Luiz Angelo Daros de Luca2022-06-071-0/+6
| | | | | | | | | A GPIO assert is required to reset the system. Otherwise, the system will hang on reboot. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit a2817ce96f17db3a5af77837ae5733b47182ae0d)
* realtek: add reset button for D-Link DGS-1210-28Luiz Angelo Daros de Luca2022-06-071-0/+18
| | | | | | | | Tested in a DGS-1210-28 F3, both triggering failsafe and reboot. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit b85f59b726442621efb95153ff60b8767723feca)
* realtek: add support for ZyXEL GS1900-24ERaylynn Knight2022-06-062-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24E * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE * Ethernet: 24x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Switch: 1 Power switch on rear of device * Power 120-240V AC C13 * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin file and select open so File Path is updated with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24E is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> (cherry picked from commit b515ad10a6e1bd5c5da0ea95366fb19c92a75dea)
* realtek: add support for ZyXEL GS1900-16Raylynn Knight2022-05-172-0/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-16 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE * Ethernet: 16x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 16 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J12) with populated standard pin connector on the right back of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin file amd select open so File Path is update with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-16 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> [removed duplicate patch title, align RAM specification] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 580723e86ae53f14273ff8c3a0ebf5d15b4ce1f1)
* kernel: bump 5.10 to 5.10.114John Audia2022-05-172-2/+2
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 8592df67f40b3afdee68e36dc3820187ec0f98fc)
* realtek: do not reset SerDes on link changeBirger Koblitz2022-05-142-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not reset the RTL930x SerDes on link changes, instead set up the SDS with internal PHYs for the SFP+ ports only. This fixes the 8 1GBit ports on the Zyxel XGS1250 which do not work without this patch. A complete SerDes reset was performed on all SerDes links. For copper 1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There is however no support for setting up the XGMII link on RTL9300/RTL9310, thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit ports. No SerDes reset should be done for these links. The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely different. All these modes need to be suitably RX calibrated and the pre- main and post- amplifiers set up properly for TX. The 10GBit SFP+ fiber links are recalibrated instead of reset, which e.g. is necessary when someone pulls a module out and puts another in. This makes swapping out 10GBit fiber modules possible. 1GBit modules are not yet supported, nor any modules with an internal phy. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [rewrite commit message based on discussion] Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit d1b824650f1ee694ec2dbdd2f4f9ec64e650cf86)
* realtek: Trap all frames with switch as destination to CPU-portBirger Koblitz2022-05-141-0/+9
| | | | | | | | | | | | | This fixes a bug where frames sent to the switch itself were flooded to all ports unless the MAC address of the CPU-port was learned otherwise. Tested-by: Wenli Looi <wlooi@ucalgary.ca> Tested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [fix code formatting] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 98bb26f9f762408e42bd8a906f0eb01c41ada10a)
* realtek: add ZyXEL GS1900-24HP v1 supportMartin Kennedy2022-04-193-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HP v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 24 ethernet port PoE status LEDs * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * PoE: * Management MCU: ST Micro ST32F100 Microcontroller * 6 BCM59111 PSE chips * 170W power budget * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a TI or SIPEX 3232C for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HP v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com> [Add info on PoE hardware to commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit a5ac8ad0ba9df50bdd0dda1dc26cf36f83006893)
* realtek: Fix tc default packageHauke Mehrtens2022-03-291-1/+1
| | | | | | | | | | | The tc package does not exits any more, it was split into tc-tiny, tc-full and tc-bpf. Include tc-bpf by default into realtek images. This increases the compressed image size by about 232KBytes. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 34fb36e165d5b6e6e37d33b4b0da789a8f1430bb)
* realtek: Use firewall4Hauke Mehrtens2022-03-291-1/+1
| | | | | | | | | | | | | | | | | | | | The realtek target is not a router, but basic device, see DEVICE_TYPE. The basic device type does not come with firewall by default, see include/target.mk for details. The realtek target extended DEFAULT_PACKAGES manually with firewall. This changes the defaults to take firewall4 and nftables instead of firewall and iptables. This also adds the additional package kmod-nft-offload. The only difference to the router type is the missing ppp, ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package. This increases the compressed image size by about 422KBytes. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 469030659c5cb140bdbff1b3d8fc9691f98f984b)
* realtek: Remove dnsmasq and odhcpd-ipv6only from defaultHauke Mehrtens2022-03-291-1/+1
| | | | | | | | | | | | Do not include the dnsmasq and odhcpd-ipv6only package by default any more. These services are not needed on a switch. If someone needs this it is still possible to use opkg or image builder to add them. This decreases the compressed image size by about 165KBytes. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 2acebbdcaafbdfd3f677052c28bc0af04c6b5ab8)
* kernel: bump 5.10 to 5.10.106John Audia2022-03-191-2/+2
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* realtek: add support for Panasonic Switch-M8eG PN28080KINAGAKI Hiroshi2022-03-133-0/+338
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on RTL8380M. Specification: - SoC : Realtek RTL8380M - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x8 + 1 - port 1-8 : TP, RTL8218B (SoC) - port 9 : SFP, RTL8380M (SoC) - LEDs/Keys : 7x / 1x - UART : RS-232 port on the front panel (connector: RJ-45) - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) - 9600n8 - Power : 100-240 VAC, 50/60 Hz, 0.5 A - Plug : IEC 60320-C13 - Stock OS : VxWorks based Flash instruction using initramfs image: 1. Prepare the TFTP server with the IP address 192.168.1.111 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to the TFTP directory 3. Download the official upgrading firmware (ex: pn28080k_v30000.rom) and place it to the TFTP directory 4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys 5. Execute the following commands and boot with the OpenWrt initramfs image rtk network on tftpboot 0x81000000 bootm 6. Backup mtdblock files to the computer by scp or anything and reboot 7. Interrupt the U-Boot and execute the following commands to re-create filesystem in the flash ffsmount c:/ ffsfmt c:/ this step takes a long time, about ~ 4 mins 8. Execute the following commands to put the official images to the filesystem updatert <official image> example: updatert pn28080k_v30000.rom this step takes about ~ 40 secs 9. Set the environment variables of the U-Boot by the following commands setenv loadaddr 0xb4e00000 setenv bootcmd bootm saveenv 10: Download the OpenWrt initramfs image and boot with it tftpboot 0x81000000 0101A8C0.img bootm 11: On the initramfs image, download the sysupgrade image and perform sysupgrade with it sysupgrade <imagename> 12: Wait ~ 120 seconds to complete flashing Note: - "Switch-M8eG" is a model name, and "PN28080K" is a model number. Switch-M8eG has an another (old) model number ("PN28080"), it's not a Realtek based hardware. - Switch-M8eG has a "POWER" LED (Green), but it's not connected to any GPIO pin. - The U-Boot checks the runtime images in the flash when booting and fails to execute anything in "bootcmd" variable if the images are not exsisting. - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock firmware and it includes the stock images, configuration files and checksum files. It's unknown format, can't be managed on the OpenWrt. To get the enough space for OpenWrt, move the filesystem to the head of "fs_reserved" partition by execution of "ffsfmt" and "updatert". - On the other devices in the same series of Switch-M8eG PN28080K, the INT pin on the PCA9555 is not connected to anywhere. Back to the stock firmware: 1. Delete "loadaddr" variable and set "bootcmd" to the original value on U-Boot: setenv loadaddr setenv bootcmd 'bootm 0x81000000' on OpenWrt: fw_setenv loadaddr fw_setenv bootcmd 'bootm 0x81000000' 2. Perform reset or reboot on U-Boot: reset on OpenWrt: reboot Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sander Vanheule <sander@svanheule.net>
* realtek: enable pca953x driver for rtl838x subtargetINAGAKI Hiroshi2022-03-131-0/+3
| | | | | | | | | | The system status LED on Panasonic Switch-M8eG PN28080K is connected to a PCA9539PW. To use the LED as a status LED of OpenWrt while booting, enable the pca953x driver and built-in to the kernel. Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Sander Vanheule <sander@svanheule.net>
* realtek: add ZyXEL GS1900-24 v1 supportMartin Kennedy2022-03-132-0/+137
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24 v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a SIPEX 3232EC for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on > Since the GS1900-24 v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com>
* realtek: add support for I-O DATA BSH-G24MBINAGAKI Hiroshi2022-03-072-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA BSH-G24MB is a 24 port gigabit switch, based on RTL8382M. Specification: - SoC : Realtek RTL8382M - RAM : DDR2 128 MiB (Nanya NT5TU128M8HE-AC) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G) - Ethernet : 10/100/1000 Mbps x24 - port 1-8 : RTL8218B - port 9-16 : RTL8218B (SoC) - port 17-24 : RTL8218B - LEDs/Keys : 2x, 1x - UART : pin header on PCB - JP2: 3.3V, TX, RX, GND from rear side - 115200n8 - Power : 100 VAC, 50/60 Hz - Plug : IEC 60320-C13 Flash instruction using sysupgrade image: 1. Boot BSH-G24MB normally 2. Connect BSH-G24MB to the DHCP enabled network 3. Find the device's IP address and open the WebUI and login Note: by default, the device obtains IP address from DHCP server of the network 4. Open firmware update page ("ファームウェア アップデート") 5. Rename the OpenWrt sysupgrade image to "bsh-g24mb_v100.image" and select it 6. Press apply ("適用") button to perform update 7. Wait ~150 seconds to complete flashing Note: - BSH-G24MB has a power-related LED ("電源"), but it's not connected to the GPIO of the SoC or RTL8231 and cannot be controlled. Instead of it, use system status LED on other than running-state. - "sys_loop" LED indicates system status and loop-detection status in stock firmware. - BSH-G24MB has 2x os-image partitions named as "RUNTIME"/"RUNTIME2" in 16 MiB SPI-NOR flash and the size of image per partition is only 6848 KiB. The secondary image is never used on stock firmware, so also use it on OpenWrt to get more space. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: net: dsa: configure better brport flags when ports leave the bridgeBjørn Mork2022-03-061-0/+148
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ensures that the DSA driver sets exactly the same default flags as the bridge when a port joins or leaves. Without this we end up with a confusing flag mismatch, where DSA and bridge ports use different sets of flags. This is critical as the "learning" mismatch will be harmful to the network, causing all traffic to be flooded on all ports. The original commit was buggy, trying to set the flags one-by-one in a loop. This was not supported by the API and the end result was that all but the last flag were cleared. This bug was implicitly fixed upstream by commit e18f4c18ab5b ("net: switchdev: pass flags and mask to both {PRE_,}BRIDGE_FLAGS attributes"). This is a minimum temporary stop measure fix for the critical lack of "learning" only. The major API change associated with a full v5.12+ backport is neither required nor wanted. A simpler fix, moving the call to dsa_port_bridge_flags() out of the loop, has therefore been merged into this modified backport. Fixes: afa3ab54c03d ("realtek: Backport bridge configuration for DSA") Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Stijn Tintel <stijn@linux-ipv6.be> [fix typos in commit message] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 5.10 to 5.10.102John Audia2022-03-012-2/+2
| | | | | | | | | | | | | | | Removed upstreamed: bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* realtek: remove debugging code from timerSander Vanheule2022-02-201-15/+3
| | | | | | | Remove some (dead) debugging code from the Realtek timer to clean up the sources of this driver. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: use DT provided address for timersSander Vanheule2022-02-202-24/+24
| | | | | | | | | | | | | | | The I/O base address for the timers was hardcoded into the driver, or derived from the HW IRQ number as an even more horrible hack. All supported SoC families have these timers, but with hardcoded addresses the code cannot be reused right now. Request the timer's base address from the DT specification, and store it in a private struct for future reference. Matching the second interrupt specifier, the address range for the second timer is added to the DT specification. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: clean up RTL930x timer DT nodeSander Vanheule2022-02-201-3/+1
| | | | | | | | | | | | | | The Realtek timer node for RTL930x doesn't have any child nodes, making the use of '#address-cells' quite pointless. It is also not an interrupt controller, meaning it makes no sense to define '#interrupt-cells'. The I/O address for this node is also wrong, but this is hidden by the fact that the driver associated with this node bypasses the usual DT machinery and does it's own thing. Correct the address to have a sane value, even though it isn't actually used. Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: ZyXEL GS1900-48: fix system LED polaritySander Vanheule2022-02-201-1/+1
| | | | | | | | | When driven by a GPIO pin, the system LED needs to be configured as active high. Otherwise the LED switches off after booting and initialisation. Fixes: 47f5a0a3eed5 ("realtek: Add support for ZyXEL GS1900-48 Switch") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: ZyXEL GS1900-48: drop status from gpio1Sander Vanheule2022-02-201-2/+0
| | | | | | | | The default value for a DT node's status property is already "okay", so there's no need to specify it again. Drop the status property to clean up the DTS. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: use higher priority for timer interruptsSander Vanheule2022-02-201-1/+1
| | | | | | | | | | | | | | The assigned output index for the event timers was quite low, lower even than the ethernet interrupt. This means that high network load could preempt timer interrupts, possibly leading to all sorts of strange behaviour. Increase the interrupt output index of the event timers to 5, which is the highest priority output and corresponds to the (otherwise unused) MIPS CPU timer interrupt. Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: move RTL8231 definitions to board filesSander Vanheule2022-02-204-21/+23
| | | | | | | | | | | | | | The RTL8231 is an external chip, and not part of the SoC. That means it is more appropriate to define it in the board specific (base) files, instead of the DT include for the SoC itself. Moving the RTL8231 definition also ensures that boards with no GPIO expander, or an alternative one, don't have a useless gpio1 node label defined. Tested on a Netgear GS110TPPv1. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: fix node addresses for RTL839xSander Vanheule2022-02-201-3/+3
| | | | | | | | | | The address in some node names doesn't match the actual offset specified in the DT node. Update the names to fix this. While fixing the node names, also drop the unused node labels. Fixes: 0a7565e53653 ("realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231 node") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: consolidate bootargs againSander Vanheule2022-02-205-11/+3
| | | | | | | | | | | | | | | | | Bootargs for devices in the realtek target were previously consolidated in commit af2cfbda2bf5 ("realtek: Consolidate bootargs"), since all devices currently use the same arguments. Commit a75b9e3ecb61 ("realtek: Adding RTL930X sub-target") reverted this without any argumentation, so let's undo that. Commit 0b8dfe085180 ("realtek: Add RTL931X sub-target") introduced the old bootargs also for RTL931x, without providing any actual device support. Until that is done, let's assume vendors will have done what they did before, and use a baud rate of 115200. Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: fix locking bug in rtl838x_hw_receive()Birger Koblitz2022-02-181-3/+4
| | | | | | | | | | | | | | A Locking bug in the packet receive path was introduced with PR #4973. The following patch prevents the driver from locking after a few minutes with an endless flow of [ 1434.185085] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000f8 [ 1434.208971] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc [ 1434.794800] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc [ 1435.049187] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
* realtek: add RTL8231 chip detectionSander Vanheule2022-02-171-1/+14
| | | | | | | | | | | | | | | | | | | | | | When initialising the driver, check if the RTL8231 chip is actually present at the specified address. If the READY_CODE value does not match the expected value, return -ENXIO to fail probing. This should help users to figure out which address an RTL8231 is configured to use, if measuring pull-up/-down resistors is not an option. On an unsuccesful probe, the driver will log: [ 0.795364] Probing RTL8231 GPIOs [ 0.798978] rtl8231_init called, MDIO bus ID: 30 [ 0.804194] rtl8231-gpio rtl8231-gpio: no device found at bus address 30 When a device is found, only the first two lines will be logged: [ 0.453698] Probing RTL8231 GPIOs [ 0.457312] rtl8231_init called, MDIO bus ID: 31 Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: always require SMI bus ID for RTL8231Sander Vanheule2022-02-171-17/+16
| | | | | | | | | | | | | | | The SMI bus ID for RTL8231 currently defaults to 0, and can be overridden from the devicetree. However, there is no value check on the DT-provided value, aside from masking which would only cause value wrap-around. Change the driver to always require the "indirect-access-bus-id" property, as there is no real reason to use 0 as default, and perform a sanity check on the value when probing. This allows the other parts of the driver to be simplified a bit. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: use automatic GPIO numbering for RTL8231Sander Vanheule2022-02-171-1/+1
| | | | | | | | | Set the gpio_chip.base to -1 to use automatic GPIO line indexing. Setting base to 0 or a positive number is deprecated and should not be used. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: fix RTL8231 gpio countSander Vanheule2022-02-171-1/+1
| | | | | | | | | | The RTL8231's gpio_chip.ngpio was set to 36, which is the largest valid GPIO index. Fix the allowed number of GPIOs by setting ngpio to 37, the actual line count. Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: rtl83xx-phy: abstract and document PHY featuresDaniel Golle2022-02-171-114/+135
| | | | | | | | | | | | | Replace magic values with more self-descriptive code now that I start to understand more about the design of the PHY (and MDIO controller). Remove one line before reading RTL8214FC internal PHY id which turned out to be a no-op and can hence safely be removed (confirmed by INAGAKI Hiroshi[1]) [1]: https://github.com/openwrt/openwrt/commit/df8e6be59a1fbce3f8c6878fe7440a129b1245d6#r66890713 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: fix locking issuesBirger Koblitz2022-02-172-26/+22
| | | | | | | Fixe a coupld of locking issues found by applying lock debugging to the code. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: switch to use generic MDIO accessor functionsDaniel Golle2022-02-176-473/+1238
| | | | | | | | Instead of directly calling SoC-specific functions in order to access (paged) MII registers or MMD registers, create infrastructure to allow using the generic phy_*, phy_*_paged and phy_*_mmd functions. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: implement Clause-45 MDIO write on rtl931xDaniel Golle2022-02-172-26/+65
| | | | | | | | | * Add missing Clause-45 write support for rtl931x * Switch to use helper functions in all Clause-45 access functions to make the code more readable. * More meaningful/unified debugging output (dynamic kprintf) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: backport Clause-45 MDIO helper functionsDaniel Golle2022-02-171-0/+53
| | | | | | | | Import commit ("c6af53f038aa3 net: mdio: add helpers to extract clause 45 regad and devad fields") from Linux 5.17 to allow making the MDIO code in the ethernet driver more readable. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: add support for port led configuration on RTL93XXBirger Koblitz2022-02-176-8/+175
| | | | | | | | | Using the led-set attribute of a port in the dts we allow configuration of the port leds. Each led-set is being defined in the led-set configuration of the .dts, giving a specific configuration to steer the port LEDs via a serial connection. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add support for the RTL8221B PHYBirger Koblitz2022-02-172-0/+18
| | | | | | | | | The RTL8221B PHY is a newer version of the RTL8226, also supporting 2.5GBit Ethernet. It is found with RTL931X devices such as the EdgeCore ECS4125-10P Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add specific PHY polling options to support the Zyxel XGS1250/XGS1210Birger Koblitz2022-02-172-14/+101
| | | | | | | | | | Both the Aquantia AQR113c and the RTL8226 PHYs in the Zyxel XGS1250 and the Zyxel XGS1210 require special polling configuration settings in the RTL930X_SMI_10GPHY_POLLING_REGxx_CFG configuration registers. Set them. Additionally, for RTL 1GBit phys set the RTL930X_SMI_PRVTE_POLLING_CTRL bits in the poll mask. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Fix link status detection on RTL9302 for SFP modulesBirger Koblitz2022-02-172-3/+23
| | | | | | | For SFP slots on the RTL9302, the link status is not correctly detected. Use the link media status instead. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add RTL931X sub-targetBirger Koblitz2022-02-177-1/+517
| | | | | | | | We add the RTL931X sub-target with kernel configuration for a dual core MIPS InterAptive CPU. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add HW support for RTL931X for PIE, L2 and STP agingBirger Koblitz2022-02-172-52/+1188
| | | | | | | | We add HW support routines for the RTL931X SoC family for handling the Packet Inspection Engine, L2 table handling and STP aging. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Store and Restore MC memberships for port enable/disableBirger Koblitz2022-02-172-55/+86
| | | | | | | | | We need to store and restore MC memberships in HW when a port joins or leaves a bridge as well as when it is enabled or disabled, as these properties should not change in these situations. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Copy all BPDUs to the kernelBirger Koblitz2022-02-174-8/+140
| | | | | | | | In order to receive STP information at the kernel level, we make sure that all Bridge Protocol Data Units are copied to the CPU-Port. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add L2 aging configuration functions for all SoC familiesBirger Koblitz2022-02-176-19/+58
| | | | | | | | Instead of a generic L2 aging configuration function with complex logic, we implement an individual function for all SoC types. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realted: Add DSA bridge offload configurationBirger Koblitz2022-02-174-1/+139
| | | | | | | | Add functionality to enable or disable L2 learning offload and port flooding for RTL83XX. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Backport bridge configuration for DSABirger Koblitz2022-02-171-0/+144
| | | | | | | | | Adds the DSA API for bridge configuration (flooding, L2 learning, and aging) offload as found in Linux 5.12 so that we can implement it in our drivver. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add Link Aggregation (aka trunking) supportBirger Koblitz2022-02-178-15/+369
| | | | | | | | | This adds LAG support for all 4 SoC families, including support ofr the use of different distribution algorithm for the load- balancing between individual links. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 23:10:13 +0000