aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/realtek/dts
Commit message (Collapse)AuthorAgeFilesLines
* realtek: add dtsi for RTL930X SoCsBirger Koblitz2021-01-261-0/+182
| | | | | | Add a default dtsi to support RTL930X SoCs. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add support for the RTL8390 and RTL9300 SoC IRQsBirger Koblitz2021-01-261-5/+4
| | | | | | | | This adds support for the RTL8390 and RTL9300 SoCs it also cleans up unnecessary definitions in mach-rtl83xx.h and moves definitions relevant for irq routing to irq.h Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: use vendor-specific magic for ZyXELBjørn Mork2021-01-241-1/+2
| | | | | | | | | | | | | | The stock firmware of the ZyXEL GS1900 series use a non-standard u-image magic. This is not enforced by the stock u-boot, which is why we could boot images with the default magic. The flash management application of the stock firmware will however verify the magic, and refuse any image with another value. Convert to vendor-specific value to get flash management support in stock firmware, including the ability to upgrade to OpenWrt directly from stock web UI. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: mtdsplit_uimage: replace "netgear, uimage" parserBjørn Mork2021-01-221-1/+2
| | | | | | | | | | | | | | | | | | | The "netgear,uimage" parser can be replaced by the generic parser using device specific openwrt,ih-magic and openwrt,ih-type properties. Device tree properties for the following devices have not been set, as they have been dropped from OpenWrt with the removal of the ar71xx target: FW_MAGIC_WNR2000V1 0x32303031 FW_MAGIC_WNR2000V4 0x32303034 FW_MAGIC_WNR1000V2_VC 0x31303030 FW_MAGIC_WPN824N 0x31313030 Tested-by: Sander Vanheule <sander@svanheule.net> # WNDR3700v2 Tested-by: Stijn Segers <foss@volatilesystems.org> # WNDR3700v1 Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: mtdsplit_uimage: replace "allnet, uimage" parserBjørn Mork2021-01-221-1/+2
| | | | | | | Convert users to the generic "openwrt,uimage" using device specific "openwrt,ih-magic" properties, and remove "allnet,uimage". Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: add support for ZyXEL GS1900-8HP v1 and v2Stijn Segers2021-01-082-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support. There are two versions on the market (v1 & v2) which share similar specs (same flash size and flash layout, same RAM size, same PoE+ power envelope) but have a different case and board layout that they each share with other GS1900 siblings. The v1 seems to share its PCB and case with non-PoE GS1900-8; as such, adding support for the GS1900-8 would probably be trivial. The v2 seems to share its casing and platform with its already supported bigger brother, the GS1900-10HP - its board looks the same, except for two holes where the GS1900-10 has its SFP ports. Like their 10 port sibling, both devices have a dual firmware layout. Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to manipulate the PoE+, one needs the rtl83xx-poe package [1]. After careful consideration it was decided to go with separate images for each version. Specifications (v1) ------------------- * SoC: Realtek RTL8380M 500 MHz MIPS 4KEc * Flash: Macronix MX25L12835F 16 MiB * RAM: Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM * Ethernet: 8x 10/100/1000 Mbit * PoE+: Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x) * UART: 1 serial header with populated standard pin connector on the left side of the PCB, towards the bottom. Pins are labeled: + VCC (3.3V) + TX + RX + GND Specifications (v2) ------------------- * SoC: Realtek RTL8380M 500 MHz MIPS 4KEc * Flash: Macronix MX25L12835F 16 MiB * RAM: Samsung K4B1G0846G 128 MiB DDR3 SDRAM * Ethernet: 8x 10/100/1000 Mbit * PoE+: Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant) * UART: 1 angled serial header with populated standard pin connector accessible from outside through the ventilation slits on the side. Pins from top to bottom are clearly marked on the PCB: + VCC (3.3V) + TX + RX + GND Serial connection parameters for both devices: 115200 8N1. Installation ------------ Instructions are identical to those for the GS1900-10HP and apply both to the GS1900-8HP v1 and v2 as well. * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-10HP is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot off the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin Signed-off-by: Stijn Segers <foss@volatilesystems.org> [merge PoE case, keep device definitions separate, change all those hashes in the commit message to something else so they don't get removed when changing the commit ...] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: remove model prefix from LED label for ZyXEL GS1900Adrian Schmutzler2021-01-081-1/+1
| | | | | | This is used as fixed status LED, so no migration is needed. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: introduce shared DTSI for GS1900 seriesStijn Segers2021-01-082-208/+153
| | | | | | | | | | | The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar Realtek RTL8380M platform. Create a common DTSI in preparation for GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi. Signed-off-by: Stijn Segers <foss@volatilesystems.org> [drop redundant includes, use &mdio directly, do not replace SFP ports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: ZyXEL: spell as done by manufacturerStijn Segers2021-01-071-1/+1
| | | | | | | ZyXEL spells its own name all uppercase with just the Y lowercase. Adapt the realtek target to follow this (other OpenWrt targets already do so). Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* realtek: move memory node to device DTSStijn Segers2021-01-076-5/+25
| | | | | | | | | Move the memory out of the rtl838x.dtsi and into the device family DTSI or device DTS if applicable. This aligns with upstream practice. Signed-off-by: Stijn Segers <foss@volatilesystems.org> [add missing block for dgs-1210-10p, move block below chosen node] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: remove duplicate '/dts-v1/;' identifierAdrian Schmutzler2021-01-072-2/+0
| | | | | | | The identifier is already present in rtl838x.dtsi, and adding it twice is not only redundant but actually wrong. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: fix SFP ports on the dlink 10port switchJohn Crispin2020-12-022-2/+14
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: add zyxel_gs1900-10hp supportJohn Crispin2020-12-021-0/+282
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: update the tree to the latest refactored versionJohn Crispin2020-11-267-0/+959
* rename the target to realtek * add refactored DSA driver * add latest gpio driver * lots of arch cleanups * new irq driver * additional boards Signed-off-by: Bert Vermeulen <bert@biot.com> Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 01:20:36 +0000