aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/realtek/dts-5.10
Commit message (Collapse)AuthorAgeFilesLines
* realtek: netgear-gs110tpp: Add system LEDsSander Vanheule2021-12-271-0/+33
| | | | | | | | The GS110TPP has an RGB LED used for system status indication. Expose all three components as separate GPIO LEDs connected via the device's RTL8231. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: netgear-gigabit: Enable RTL8231Sander Vanheule2021-12-271-2/+4
| | | | | | | | | | | | | | | | Since the move to 5.10, there are now two GPIO drivers. The gpio0 node refers to the internal GPIOs, so the indirect-access-bus-id is no longer relevant for that node. Set indirect-access-bus-id to the correct value (31) on the correct node (gpio1) and enable the device. Cc: Raylynn Knight <rayknight@me.com> Cc: Michael Mohr <akihana@gmail.com> Cc: Stijn Segers <foss@volatilesystems.org> Cc: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Bjørn Mork <bjorn@mork.no>
* realtek: netgear-gigabit: Add gpio-restart nodeSander Vanheule2021-11-281-0/+6
| | | | | | | | | | | | | | | | The Netgear GS110TPP v1 switch cannot reliably perform cold reboots using the system's internal reset controller. On this device, and the other supported Netgear switches, internal GPIO line 13 is connected to the system's hard reset logic. Expose this GPIO on all systems to ensure restarts work properly. Cc: Raylynn Knight <rayknight@me.com> Cc: Michael Mohr <akihana@gmail.com> Cc: Stijn Segers <foss@volatilesystems.org> Cc: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Bjørn Mork <bjorn@mork.no>
* realtek: add missing GPIO irq propertiesSander Vanheule2021-11-281-0/+4
| | | | | | | | | The internal GPIO controller on RTL838x is also an IRQ controller, which requires the 'interrupt-controller' and '#interrupts-cells' properties to be present in the device tree. Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: Add and enable watchdog nodeSander Vanheule2021-11-242-1/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add and enable the Realtek Otto WDT peripheral found on these SoCs. Default all devices to use standard (cold) reboot and "soc" resets. Devices that require the PLL value fixup before restarting, should pick the "cpu" or "software" reset mode. These devices also need to provide a custom reboot mode, by adding the reboot argument to the kernel command line: WDT reset mode | kernel reboot mode ----------------+--------------------------------------- soc | reboot=cold (default if not specified) cpu | reboot=warm software | reboot=software Preferrably, these devices should use an alternative restart method like gpio-restart to provide reliable restarts. Note that watchdog restarts are not yet exposed, since the _machine_restart override is still present. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Add Lexra bus clockSander Vanheule2021-11-242-8/+13
| | | | | | | | | | | | | | | | | The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the Lexra bus. This bus can provide a clock signal to these peripherals, but no clock driver is currently available. Instead, use a fixed-clock to provide the clock frequency, and update the dependent peripherals. Lexra bus clock frequencies: - RTL838x: 200MHz - RTL839x: 200MHz - RTL930x: 175MHz Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Consolidate bootargsSander Vanheule2021-11-248-26/+2
| | | | | | | | | | All current devices use identical bootargs, so let's move that to the common devicetree includes. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: enable uart1 on the devices with PoE support in 5.10INAGAKI Hiroshi2021-09-267-0/+28
| | | | | | | | | | | | | | | | On the devices with PoE support, the secondary UART (uart1) on the SoC is used to communicate between the SoC and controller. Enable the secondary UART on the following devices: - D-Link DGS-1210-10P - Netgear GS110TPP v1 - Netgear GS310TP v1 - ZyXEL GS1900-8HP v1/v2 - ZyXEL GS1900-10HP - ZyXEL GS1900-24HP v2 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: use physical addresses in soc dtsi in 5.10INAGAKI Hiroshi2021-09-262-12/+12
| | | | | | Use physical addresses instead of virtual address in dts files. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: use gpio-keys instead of "-polled" if SoC GPIO is used in 5.10INAGAKI Hiroshi2021-09-262-4/+2
| | | | | | | | The new backported GPIO driver supports interrupt, so use gpio-keys instead of gpio-keys-polled for keys connected to the internal GPIO controller. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: update GPIO bindings in the dts files in dts-5.10INAGAKI Hiroshi2021-09-266-33/+29
| | | | | | | | | | | | | | | | | | | this patch includes the following changes: - adjust mapping for the new driver - GPIO 24 -> GPIO 0 - GPIO 47 -> GPIO 0 (+ disabling system LED) - disable pins in the invalid range (out of the range 0-31 of the new driver) - are these pins on the external RTL8231 (&gpio1)? - GPIO 67 (-> GPIO 3 on &gpio1?) - GPIO 94 (-> GPIO 30 on &gpio1?) - drop "indirect-access-bus-id" property from gpio0 node in device dts files Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: add pinmux node of LED_GLB_CTRL to rtl838x.dtsi in dts-5.10INAGAKI Hiroshi2021-09-261-0/+16
| | | | | | | This patch adds a pinctrl-single pinmux node to allow disabling system LED and enabling GPIO 0 (old driver: GPIO 24). Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: add "soc" node to soc dtsi in dts-5.10INAGAKI Hiroshi2021-09-262-129/+147
| | | | | | Add a "soc" node as a simple-bus to rtl838x.dtsi and rtl930x.dtsi. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: update soc dtsi in 5.10 for backported driversINAGAKI Hiroshi2021-09-262-6/+41
| | | | | | | | | | | | | | | this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the following backported drivers: - gpio-realtek-otto (5.13) - spi-realtek-rtl (5.12) - irq-realtek-rtl (5.12) And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10. Currently, the upstreamed driver doesn't support the GPIO controller on RTL930x SoC. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: cleanup and update soc dtsi in 5.10INAGAKI Hiroshi2021-09-262-28/+11
| | | | | | | | | | the following changes are included in this patch: - node is enabled by default, drop 'status = "okay"' - adjust order of "compatible" lines and "reg" lines - add a new blank line before fixed-link node in rtl830x.dtsi Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: copy dts directory for Kernel 5.10INAGAKI Hiroshi2021-09-2621-0/+1707
This patch adds "dts-5.10" directory to use backported drivers. There are several specification changes in the new drivers, so there are some compatibility issues in using dts/dtsi files for 5.4. The old DTS files are moved to "dts-5.4", so their corresponding kernel version is obvious as well. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [change "dts" to "dts-5.4", adjust Makefile] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-16 21:48:54 +0000