aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix ethernet MAC address of ASUS RT-AC57UAdrian Schmutzler2019-09-091-1/+1
| | | | | | | This backports the only non-cosmetic fix from 6640e1c3681b ("ramips: clean and improve MAC address setup in 02_network"). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix duplicate network setup for dlink, dir-615-h1Adrian Schmutzler2019-09-091-1/+0
| | | | | | | | | | | | | | | In 555ca422d1cb ("ramips: fix D-Link DIR-615 H1 switch port mapping"), port setup for dir-615-h1 was changed without removing the old one. This was working as the new one was triggered earlier than the old one. (In the meantine, changed sorting during ramips rename patches actually inversed that order.) Anyway, just remove the wrong case now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit e35e4a996e26f17b69d200505ecea78af96a2704)
* ramips: remove duplicate case for MAC setup of freestation5Adrian Schmutzler2019-09-091-1/+0
| | | | | | | | | | | | | ARC FreeStation5 is present twice in MAC address setup. >From older commits/changes, it is not possible to reconstruct the correct choice only by reading the annotations. Thus, remove the second case and keep the first one, so behavior stays the same (as nobody seems to have complained about it). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit ad4eb2241b33b05b0942a3fa7ed2e53fb6e84386)
* mt7620: disable image generation for Nexx WT3020 (4MB)Hauke Mehrtens2019-09-081-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file openwrt-19.07-snapshot-r10495-db5164d3d0-ramips-mt7620-wt3020-4M-squashfs-factory.bin is too big Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-09-071-4/+4
| | | | | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 8b4bc7abe073489a3595eeb2d81818852319c148) [rmilecki: dropping ARGV without this change broke sysupgrade] Fixes: 6ac62c4b6cae ("base-files: don't set ARGV and ARGC")
* ramips: fix network setup for various NETGEAR boardsDavid Bauer2019-09-071-11/+6
| | | | | | | | | | | | | | | | | There are currently the following issues present for the Netgear R6220, R6350 and WNDR3700 v5: - LAN and WAN MAC-addresses are inverted - WAN MAC-address is off. It are +2 compared to the LAN MAC-address (R6350 only) - Switchport order is inverted in LuCi This commit fixes both these issues by assigning correct MAC-addresses to LAN and WAN interfaces and defining the switchports with the correct labels. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 13937a16d40693df67d3d39faa3a80644bdb7abf)
* ramips: use phy trigger for various Netgear boardsDavid Bauer2019-09-073-1/+2
| | | | | | | | | | This commit switches the default trigger for the WiFi LED from a netdev trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED to work, even when the wireless interface is not named "wlan0" without modifiying the LED settings. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit fa46c9b208fe3833f085e9f6ddf7c492b16f6c34)
* ramips: disable badblock shifting for MT7621 NANDDavid Bauer2019-09-071-1/+1
| | | | | | | | | | | | | | | | | | The MediaTek MT7621 NAND driver currently intransparently shifts NAND pages when a block is marked as bad. Because of this, offsets for e.g. caldata and MAC-addresses seem to be off. This is, howeer, not a task for the mtd NAND driver, as the flash translation layer is tasked with this. This patch disables this badblock shifting. This fix was originally proposed by Jo-Philipp Wich at https://bugs.openwrt.org/index.php?do=details&task_id=1926 Fixes FS#1926 ("MTD partition offset not correctly mapped when bad eraseblocks present") Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 527832e54bf3bc4d699a145ae66f34230246f0a9)
* ramips: add support for ASUS RT-AC57UDavid Bauer2019-07-213-4/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 14e0e4f138e35c3e2a15cc3a836c939547ee053b)
* mt7620: disable image generation for Netgear EX2700Petr Štetiar2019-07-201-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: add IRQ for GPIO nodeChuanhong Guo2019-06-271-0/+3
| | | | | | | This makes interrupt-based gpio-keys working. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 110daa16e44bb53941a18396ab6a7d9fdd1fa362)
* kernel: bump 4.14 to 4.14.128Koen Vandeputte2019-06-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-122-4/+4
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: Remove redundant LED-casesKristian Evensen2019-06-101-68/+32
| | | | | | | 01_leds has several redundant LED-cases. This commit cleans up the file by merging these cases into shared cases. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TOTOLINK LR1200Chuanhong Guo2019-06-053-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7628DAN (MT7628AN with 64MB built-in RAM) - Flash: 8M SPI NOR - Ethernet: 5x 10/100Mbps - WiFi: 2.4G: MT7628 built-in 5G: MT7612E - 1x miniPCIe slot for LTE modem (only USB pins connected) - 1x SIM slot Flash instruction: U-boot has a builtin web recovery page: 1. Hold the reset button while powering it up 2. Connect to the ethernet and set an IP in 192.168.1.0/24 range 3. Open your browser and upload firmware through http://192.168.1.1 Note about the LTE modem: If your router comes with an EC25 module and it doesn't show up as a QMI device, you should do the following to switch it to QMI mode: 1. Install kmod-usb-serial-option and a terminal software (e.g. minicom or screen). All 4 serial ports of the modem should be available now. 2. Open /dev/ttyUSB3 with the terminal software and type this AT command: AT+QCFG="usbnet",0 3. Power-cycle the router. You should now get a QMI device recognized. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1Pawel Dembicki2019-06-051-0/+5
| | | | | | | | | Support for D-Link DWR-118 A1 was added before LEDs feature in mt76x0e driver. This fixes the 5GHz WiFi LED which was previously inverted. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: ethernet: remove unused SIOCETHTOOL ioctl handlingPetr Štetiar2019-06-051-12/+1
| | | | | | | | | | | | | This ioctl is currently routed through generic interface code. dev_ioctl dev_ethtool __ethtool_get_link_ksettings phy_ethtool_ioctl Cc: Felix Fietkau <nbd@nbd.name> Cc: John Crispin <john@phrozen.org> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: create R6220 dtsi and improve WNDR3700v5 supportJan Hoffmann2019-05-316-207/+166
| | | | | | | | | | | | | | | | | | The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and having a different casing. This adds a new cleaned up R6220.dtsi with the common bits for both devices. Both devices now have feature parity. Performed cleanup: * generic DTS node names * regulator for usb power * added missing pinctrl groups * use switch port instead of VLAN as trigger for WAN LED Fixes for WNDR3700v5: * all LEDS work * correct ethernet MAC addresses Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Xiaomi Mi Router 4A (100M Edition)Markus Scheck2019-05-313-0/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - SoC: MediaTek MT7628AN - Flash: 16MB (Winbond W25Q128JV) - RAM: 64MB - Serial: As marked on PCB, 3V3 logic, baudrate is 115200 - Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN) - WIFI0: MT7628AN 2.4GHz 802.11b/g/n - WIFI1: MT7612EN 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable power-LED (two-colored, yellow/blue) Non-programmable internet-LED (shows WAN-activity) - Buttons: Reset INSTALLATION: 1. Connect to the serial port of the router and power it up. If you get a prompt asking for boot-mode, go to step 3. 2. Unplug the router after > Erasing SPI Flash... > raspi_erase: offs:20000 len:10000 occurs on the serial port. Plug the router back in. 3. At the prompt select option 2 (Load system code then write to Flash via TFTP.) 4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the Server-IP. 5. Connect your computer to LAN1 and assign it as 192.168.1.2/24. 6. Rename the sysupgrade image to test.bin and serve it via TFTP. 7. Enter test.bin on the serial console and press enter. Signed-off-by: Markus Scheck <markus@mscheck.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added mt76 compatible]
* ramips: add CUDY WR1000 supportDavide Fioravanti2019-05-314-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas Specifications: MT7628 (580 MHz) 64 MB of RAM (DDR2) 8 MB of FLASH 2T2R 2.4 GHz (MT7628) 2T2R 5 GHz (MT7612E) 3x 10/100 Mbps Ethernet (2 LAN + 1 WAN) 2x external, non-detachable antennas (5dbi) UART header on PCB (57600 8n1) 7x LED, 2x button Known issues: The Power LED is always ON, probably because it is connected directly to power. Flash instructions ------------------ Load the ...-factory.bin image via the stock web interface. Openwrt upgrade instructions ---------------------------- Use the ...-sysupgrade.bin image for future upgrades. Revert to stock FW ------------------ Warning! This tutorial will work only with the following OEM FW: WR1000_EU_92.122.2.4987.201806261618.bin WR1000_US_92.122.2.4987.201806261609.bin If in the future these firmwares will not be available anymore, you have to find the new XOR key. 1) Download the original FW from the Cudy website. (For example WR1000_EU_92.122.2.4987.201806261618.bin) 2) Remove the header. dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64 3) XOR the new file with the region key. FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this: xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767.. Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!): https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false) 4) Check the resulting decrypted image. Check if bytes from 0x20 to 0x3f are: 4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Alternatively, you can use u-boot's tool dumpimage tool to check if the decryption was successful. It should look like: # dumpimage -l stock-firmware.bin Image Name: Linux Kernel Image Created: Tue Jun 26 10:24:54 2018 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB Load Address: 80000000 Entry Point: 8000c150 5) Flash it via forced firmware upgrade and don't "Keep Settings" CLI: sysupgrade -F -n stock-firmware.bin LuCI: make sure to click on the "Keep settings" checkbox to disable it. You'll need to do this !TWICE! because on the first try, LuCI will refuse the image and reset the "Keep settings" to enable. However a new "Force upgrade" checkbox will appear as well. Make sure to do this very carefully! Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added wifi compatible, spiffed-up the returned to stock instructions]
* ramips: unify JCG helper command definitionDavide Fioravanti2019-05-312-5/+6
| | | | | | | This patch makes the JCG helper command definition available for every rampis target Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for Telco Electronics X1Nicholas Smith2019-05-184-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 256MB DDR3 Flash: 16MB SPI-NOR WiFi: 2.4GHz: MT7603 @ PCIe0 WiFi: 5.8GHz: MT7612 @ PCIe1 Modem: Sierra Wireless MC74xx Interfaces: GBE RJ45 x5 mPCIe x2 UART x1 I2C x1 JTAG x1 UIM x1 LEDs x6 Flash instructions: Flash from within the factory bootloader, firmware web interface or CLI using sysupgrade -F -n Signed-off-by: Nicholas Smith <mips171@icloud.com>
* ramips: add factory image for WNDR3700v5Jan Hoffmann2019-05-183-17/+24
| | | | | | | | | This uses the existing rules for Sercomm factory images and moves them to the ramips image Makefile, so they can be used in all subtargets. The new factory image for WNDR3700v5 can be flashed using nmrpflash. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for HILINK HLK-7628NLiu Yu2019-05-184-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 128 MB Flash: 32 MB WIFI: 802.11n/g/b 20/40 MHz Ethernet: 5 Port ethernet switch UART: 2x Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART0 line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. 5. After firmware is started connect via ethernet at 192.168.1.1 Signed-off-by: Liu Yu <f78fk@live.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-175-1/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-176-1/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.118Koen Vandeputte2019-05-131-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch Altered: - 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: fix R6120 factory imageDavid Bauer2019-05-111-1/+1
| | | | | | | | | | | The factory firmware omits the JFFS2 end-marker while flashing via web-interface. Add a 64k padding after the marker fixes this problem. When the end-marker is not present, OpenWRT won't save the overlayfs after initial flash. Reported-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7620: fix dependenciesDeng Qingfang2019-05-111-1/+1
| | | | | | | | | | | | | MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies according to original Kconfig and lsmod output This will remove some unnecessary packages from MT7620 target to save some space Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 characters per line in the commit message]
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-144-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-133-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix pinctrl to allow hardware i2c on WRTNODE2RDaniel Golle2019-04-111-1/+11
| | | | | | | | Instead of assigning I2C pins as GPIOs by default, leave it up to the user whether to install kmod-i2c-mt7621 and use them for hardware I2C instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: correct DTS for Belkin F9K1109v1 to include switch definitionKip Porterfield2019-04-061-0/+11
| | | | | | | | | Add switch definition for the rtl8367b switch to the DTS/DTSi for the Belkin F9K1109v1 that was mistakenly omitted from the initial commit. Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1) Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ramips: backport mt7621-spi from linux-next-20190329Chuanhong Guo2019-04-061-261/+213
| | | | | | | | | | | | | Upstream driver has gone through a series of cleanup and was moved from drivers/staging into drivers/spi. Backport it to replace our messy driver. Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de> [LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module] Tested-by: Rosen Penev <rosenp@gmail.com> Tested-by: Tian Xiao bo <peterwillcn@gmail.com> [Newifi-D2 MediaTek MT7621 ver:1 eco:3] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: enable R6120 USB powerDavid Bauer2019-04-062-1/+16
| | | | | | | Enable the USB power for the Netgear R6120. Otherwise, no power is supplied to an attached USB device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-063-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* ramips: implement vlan rx offload on MT7621Felix Fietkau2019-04-033-4/+11
| | | | | | Avoids the overhead of software VLAN untagging in the network stack Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add missing SPDX identifier for EX6150David Bauer2019-03-311-0/+1
| | | | | | | This adds the SPDX license identifier for the NETGEAR EX6150. It was missed when submitting the original patch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Increase GB-PC1 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | The specific flash chip used (W25Q256FVEM) accepts 50MHz for read requests and higher for others. 104MHz for fast reads. ramips seems to be limited to 80MHz based on testing with higher values (no speedup). Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s [test done with backported upstream v4.19 driver[1], for numbers on stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI frequency to 80MHz` commit message] 1. https://github.com/openwrt/openwrt/pull/1578 Signed-off-by: Rosen Penev <rosenp@gmail.com> [expanded note about spi driver version] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Increase GB-PC2 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The flash chip on the board (Spansion S25FL256SAIF00) is rated to support at least 50MHz for normal read requests according to the datasheet. 133MHz for fast reads. However, ramips seems to be limited to 80MHz. >From testing this, higher values do not improve speeds. time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.82s to 14.09s. boot speed is also faster: [ 66.884087] procd: - init - vs [ 48.976049] procd: - init - Since spi speed was requested: [ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000 CPU is 900MHz: [ 0.000000] CPU Clock: 900MHz Signed-off-by: Rosen Penev <rosenp@gmail.com> [fixed commit message by adding missing 0 in the spi-mt7621 clock output] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add Netgear EX6150David Bauer2019-03-293-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621 RAM: 64M (Winbond W9751G6KB-25) FLASH: 16MB (Macronix MX25L12835F) WiFi: MediaTek MT7662E bgn 2SS WiFi: MediaTek MT7662E nac 2SS BTN: ON/OFF - Reset - WPS - AP/Extender toggle LED: - Arrow Right (blue) - Arrow Left (blue) - WiFi 1 (red/green) - WiFi 2 (red/green) - Power (green/amber) - WPS (Green) UART: UART is present as Pads on the backside of the PCB. They are located on the other side of the Ethernet port. 3.3V - GND - TX - RX / 57600-8N1 3.3V is the nearest one to the antenna connectors Installation ------------ Update the factory image via the Netgear web-interfaces (by default: 192.168.1.250/24). You can also use the factory image with the nmrpflash tool. For more information see https://github.com/jclehner/nmrpflash Signed-off-by: David Bauer <mail@david-bauer.net> [merge conflict in 02_network, flash@0 node rename, wlan DTS triggers] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ZyXEL Keenetic StartVladimir Kot2019-03-294-0/+132
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: RT5350F - CPU Frequency: 360 MHz - Flash Chip: Winbond 25Q32 (4096 KiB) - RAM: 32768 KiB - 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) - 1x external, non-detachable antenna - UART (J1) header on PCB (57800 8n1) - Wireless: SoC-intergated: 2.4GHz 802.11bgn - USB: None - 3x LED, 2x button Flash instruction: 1. Configure PC with static IP 192.168.1.2/24 and start TFTP server. 2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin" to "kstart_recovery.bin" and place it in TFTP server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. 4. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Vladimir Kot <vova28rus@gmail.com> [fixed git commit author and whitespace issues in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for WIZnet WizFi630S boardTobias Welz2019-03-293-0/+204
| | | | | | | | | | | | | | | | | | | | The WIZnet WizFi630S board is in the miniPCIe form factor. SoC: Mediatek MT7688AN RAM: 128MB Flash: 32Mb WiFi: 2.4GHz Ethernet: 3x 100Mbit USB: 1 (USB 2.0) serial ports: 2 (1x full, 1xlite) Flash and recovery instructions: Use the factory installed u-boot boot loader. It is available on UART2 (115200,8,n,1). Then get the sysupgrade image from a tftp server. Signed-off-by: Tobias Welz <tw@wiznet.eu> [whitespace and device name in makefile fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.108Koen Vandeputte2019-03-271-2/+2
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0033-i2c-bcm2835-Add-debug-support.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: allow packets with ttl=0Felix Fietkau2019-03-241-2/+2
| | | | | | | Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0. This trips up the TTL=0 check in the PPE if enabled. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-245-0/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkdlinkfw: add kernel image offsetPawel Dembicki2019-03-242-33/+23
| | | | | | | | Some boards with JBOOT have partiton between bootloader and kernel image. This patch add possibility to change kernel partition start address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix wrong i2s clock unit from kHz to MHzQin Wei2019-03-241-1/+1
| | | | | | | | | | | clk_get_rate returns the current clock rate in Hz for a clock source so if we divide it by 1M, then we get frequency in MHz and not kHz. Signed-off-by: Qin Wei <support@vocore.io> [added missing commit message, and fixed author with SoB from PR message] Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Speed up eeprom read/writeAdrian Schmutzler2019-03-211-2/+2
| | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 23:11:36 +0000