aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Archer C50 cleanupHenryk Heisig2016-10-313-24/+54
| | | | | | | | | | | - setting read-only flag to important partitions - enabling PA to improve 2.4 GHz signal strength - add missing leds - rename colour led - add mac adress to 5GHz wlan interface - included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h> Signed-off-by: Henryk Heisig hyniu@o2.pl
* ramips: Add RTC driver to kernel for working hctosysRosen Penev2016-10-312-2/+3
| | | | | | | Build the RTC driver into the kernel, (and remove the optional module), in order to make hctosys working. (Currently the module is loaded after hctosys has failed previously) Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix PSG1218 LEDsXuefu Lin2016-10-263-5/+6
| | | | Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* switch to the new usbport LED triggerRafał Miłecki2016-10-1910-36/+36
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for Planex VR500.YuheiOKAWA2016-10-157-1/+112
| | | | | | | | | | | | SOC: MT7621A RAM: 256MiB NOR: MX25L51245G Non Wireless Router. Issue: soft reboot problem. SPI Flash do not exit 4byte address mode. Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
* ramips: use rfkill for wps button on wlan only boardsMathias Kresin2016-10-157-29/+8
| | | | | | | | | | | | | All of the touched boards don't have an ethernet port. Allow to use the wps button on these boards to enable the wireless radio after boot. The force enabled wireless for the DCH-M225 is removed. It is reckless to bring up an unencrypted wireless network by default these days. Using the wps button to bring up the radio seam to me the better approach. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use rootfs splitter and new image build code for BR-6475NDMathias Kresin2016-10-152-43/+11
| | | | | | | Use the edimax uImage splitter instead of the fixed size rootfs partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move edimax images to the new build codeMathias Kresin2016-10-153-32/+37
| | | | | | | | | | | | | | | | Images installed via TFTP recovery or the Edimax webinterface of the 3g-6200n(l) are writting with the edimax header to flash. Use only one image type for these boards. The migration to the factory only images need to be done via TFTP recovery. Use the same start address for the 3g-6200n(l) factory images as the stock firmware images. Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl and the patient testing of all changes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: improve edimax 6200n/nl supportMathias Kresin2016-10-154-12/+20
| | | | | | | | | | Assign the reset functionality to the wps/reset buttons. Use the wlan switch of the 6200n to enable/disable wlan. Add the internet led of the 6200nl and use the led for boot status indication Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix edimax 6200nl switch configMathias Kresin2016-10-152-2/+1
| | | | | | | | | | | | | With 3a9752bbd2bc00e407b5dcad21789720f40abf0e and later changes to ramips_set_preinit_iface() the default vlan config applied during preinit was changed. These changes were made without updating the default network config to ensure that vlan interfaces used for lan/wan are still configured. Fix the issue by using the default all LAN portmap and disabling not connected switch ports using portdisable device tree parameter. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: tag the CPU switch portMathias Kresin2016-10-151-1/+1
| | | | | | | | | | | | With de5102651501e51c036f88fe9c4dbf6974e5158a the explicit tagging of the CPU port was removed. This leads to a not working default network config, with vlans enabled but disabled CPU tagging, for boards where all switch ports are having the same role. In case the ports are having different roles set, tagging is is set implicit for the CPU port by ucidef_add_switch(). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove fixed lan/wan interface for switch configsMathias Kresin2016-10-151-1/+0
| | | | | | | | | | Don't set the lan/wan interface when using ucidef_add_switch. This results into a wan interface albeit all ports a annotated as lan ports. ucidef_add_switch takes care of setting the correct lan/wan interface according to the annotation of the ports. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zyxel NBG-419N2 (WAP3205v2)Klaus2016-10-046-0/+134
| | | | | | | | | | | applied bb-final-ramips-add-zyxel-nbg-419n2.patch from 123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65; see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905, modified slightly to fit to CC release and to new lede build system: image/rt305x.mk include file is used now changed NBG-419N2.dts format to fit style of other dts files Signed-off-by: Klaus <k-laus@quantentunnel.de>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-047-0/+136
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* kernel: update to v4.4.23Álvaro Fernández Rojas2016-09-301-3/+3
| | | | | | | Refresh patches for all targets that support kernel 4.4. compile/run-tested on brcm2708/bcm2710 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: update kernel 4.4 to version 4.4.22Stijn Segers2016-09-302-3/+3
| | | | | | Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx. Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ramips: Xiaomi MiWiFi Nano: fix status ledCezary Jackiewicz2016-09-292-2/+2
| | | | | | | - add status led for Xiaomi MiWiFi Nano - revert https://github.com/lede-project/source/commit/af1e70b4a730e91ce1668d506ebc5c1c8cf5abf5 , this should not be added. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips : add support for Newifi D1BangLang Huang2016-09-277-0/+178
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips : add support for PandoraBox D1BangLang Huang2016-09-277-1/+177
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-277-0/+136
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: fix DEVICE_PACKAGES of Ubiquiti EdgeRouter XMatthias Schiffer2016-09-261-1/+1
| | | | | | | kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on kmod-cfg80211. kmod-rt2800-pci should not be installed anyways. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: move /lib/ramips.sh include in /etc/init.d/bootcount into start()Matthias Schiffer2016-09-251-1/+2
| | | | | | Enabling the init script offline will print an error otherwise. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: do not "local" variables outside of a functionMartin Blumenstingl2016-09-241-1/+1
| | | | | | | | | Older busybox versions allowed using the local keyword outside of functions, whereas 1.25.0 (which was introduced in 06fa1c46fc32) do not allow this anymore (leading to the following error when executing the script: "file: local: line nn: not in a function"). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: update kernel 4.4 to version 4.4.21Álvaro Fernández Rojas2016-09-161-3/+3
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: fix wrong blocksizesMathias Kresin2016-09-153-3/+2
| | | | | | | | | | | | | | | | | | The D-Link DIR-860L B1 has a flash chip which doesn't support 4K sectors. Since the DIR-860L B1 was the only mt7621 board which had the 4k blocksize set, the 4K sector support is removed from the kernel config. I've checked the flash chips of all boards having set a 4K blocksize again. This time I searched harder to finding bootlogs instead of relying on wikis articles and/or the device tree source file. The Planex MZK-DP150N has an en25q32b instead of the mentioned one in the dts. Albeit the en25q32b supports 4K sectors, 4K support is not enabled in the driver. Change the blocksize for this board back to 64K. Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update kernel 4.4 to version 4.4.20Álvaro Fernández Rojas2016-09-154-5/+5
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: enable 4K sector support in kernel configMathias Kresin2016-09-134-0/+4
| | | | | | | | | | | | This is a follow up to 28110727f1d513a6c4c13aa87ecb606aa5d306eb "ramips: set blocksize for 4MB devices". I've missed to include the required changes of the kernel configs to enable 4K sector size support. The option is only enabled for targets having boards with 4k sector size flash chips. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: add KERNEL_SIZE to the default device varsMathias Kresin2016-09-131-1/+1
| | | | | This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes the underlying issue.
* build: drop UBI EOF marker from images by defaultFelix Fietkau2016-09-121-0/+1
| | | | | | | | Only add them where they are actually required. Should help with compatibility issues with stock U-Boot images that access UBI Signed-off-by: Felix Fietkau <nbd@nbd.name>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-2/+2
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: board.d merge redundant switch/interface configsMathias Kresin2016-09-101-11/+6
| | | | | | Fix alphabetical order distortions as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: set blocksize for remaining rt3883 devicesMathias Kresin2016-09-081-0/+4
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove old build code seama recipeMathias Kresin2016-09-031-32/+0
| | | | | | | Now that all seama images are using the new build code this seama recipe used with the old build code can be dropped. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: switch DIR-610 A1 to new image build codeMathias Kresin2016-09-081-3/+17
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: switch some rt3883 devices to new build codeMathias Kresin2016-09-031-25/+52
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move seama build recipe to MakefileMathias Kresin2016-09-033-18/+9
| | | | | | | The identical build step is defined twice. Move it to the parent Makefile to use only one version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: switch DIR-615 H1 to new image build codeMathias Kresin2016-09-021-11/+8
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add build recipe for senao headerMathias Kresin2016-08-171-0/+5
| | | | | | | Add it to the Makefile to allow a board which will be supported soon to use the recipe as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: set blocksize for 4MB devicesMathias Kresin2016-09-035-4/+39
| | | | | | | | | | | | | | | | | | | | | | | | Set the blocksize for devices having only 4MB of flash for ramips devices already using the new image build code. Informations about the used flash chip are gathered from the OpenWrt wiki, wikidevi, forums, OEM bootlogs or the compatible property in the device tree source file. The en25q32b from the AirLive Air3GII does not have 4k support in the kernel. For the following boards no information about the used flash chip could be found and a 64k blocksize is assumed: - Ralink V11ST-FE - Ralink AP-RT3052-V22RW-2X2 - MediaTek MT7628 EVB - MediaTek MT7621 EVB - UPVEL UR-326N4G - Buffalo WZR-AGL300NH Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: don't set the same max image size twiceMathias Kresin2016-09-043-50/+0
| | | | | | The ralink_default_fw_size_8M is already set for the default device. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: specify max image size in Kilobyte/MegabyteMathias Kresin2016-09-044-41/+22
| | | | | | Use the k and m unit suffix to be consistent with the blocksize. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: use k as unit suffix for blocksizeMathias Kresin2016-09-041-2/+2
| | | | | | | Use k as unit suffix for kilobyte to have a the same unit regardless of the used filesystem. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: mtd: backport Macronix sector size fixMathias Kresin2016-09-031-3/+3
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use lower case names for TEW-69xGR imagesMathias Kresin2016-09-091-4/+4
| | | | | | | Use lower case variant of the device name for to images to be consistent with all other images names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix wrong TARGET_DEVICESMathias Kresin2016-09-081-1/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix wrong device titleMathias Kresin2016-09-081-1/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Mercury MAC1200R v2Daniel Golle2016-09-096-0/+111
| | | | | | | | MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM reset button GPIO is still missing (anyone?) bootloader password is 'slp' Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* build: fix subtarget descriptionsFelix Fietkau2016-09-041-4/+4
| | | | | | Move Target/Description above the target.mk include Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix legacy initramfs imagesFelix Fietkau2016-09-031-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621: switch to 24kcJonas Gorski2016-08-231-1/+1
| | | | | | | | 1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly the same and will generate identical code, so there is no need to tune to 1004kc instead of 24kc. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>