aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: disable unsupported background-radarDavid Bauer2022-05-292-0/+6
| | | | | | | | The UniFi 6 Lite as well as the Tenbay T-MB5EU do not have the third background-radar chain. For the Tenbay, the connector is present, however no antenna is connected to it. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-164-0/+379
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add led_source for Asus RT-AC1200 devicesTamas Balogh2022-05-151-0/+1
| | | | | | | | | | | | | | | this adds the mediatek,led_source dts binding for Asus RT-AC1200 devices' dtsi, for correct switch LED behavior. The dts-binding is introduced in commit: 65dc9e0980255b15402c45b840f239b85be59b3d Without this, we only have constantly very fast blinking LEDs, which don't react on any traffic or LAN events at all. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: fix booting on Samknows SK-WB8Piotr Dymacz2022-05-131-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #9824 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: bump 5.15 to 5.15.36Rui Salvaterra2022-05-091-2/+2
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-093-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add i2c in dts for GL-MT300N-V2Ptilopsis Leucotis2022-05-051-0/+4
| | | | | | | | According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/ GL-MT300N-V2 have I2C interface on GPIO4, GPIO5. Adding I2C in device tree make possible using I2C on this device. Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
* ramips: ethernet: ralink: add led_source dts-bindingTamas Balogh2022-05-011-10/+17
| | | | | | | | | | | | | | | | | | | | this adds the new dts-binding "mediatek,led_source" currently for MT7628AN and MT7688 built-in switches, which is documented as a 3-bit field configuring the switch LEDs for various control schemes from 0 to 3. Normally this is not needed, but e.g. for Asus RT-AC1200-V2 it is a must to set it to the anyway undocumented value of 4, to have the switch LEDs react correctly on link/act events. This is an MT7628DAN device, but I doubt this is a speciality of this particular SoC. Also added the RT305X_ESW_LED_OFF value to LED states. Did also rename the register RT5350_EWS_REG_LED_POLARITY to RT5350_EWS_REG_LED_CONTROL, which is the correct name. Also making use of defines for some hardcoded values. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: zbt-wg2626: Fix the LAN ports namesAlban Bedel2022-05-011-4/+4
| | | | | | | The current names don't match with the labels on the case, reverse the LAN ports order so they match. Signed-off-by: Alban Bedel <albeu@free.fr>
* ramips: zbt-wg2626: Add the reset gpio for PCIe port 1Alban Bedel2022-05-011-0/+3
| | | | | | | | | | | | | The 2.4GHz interface doesn't come up properly with the log showing: mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) As seen on other MT7621 boards this is caused by a missing reset GPIO. The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO list to also reset the 2.4GHz interface on port 1. Signed-off-by: Alban Bedel <albeu@free.fr>
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-04-303-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: create shared DTSI for Wavlink WN53XAX devicesDavide Fioravanti2022-04-302-184/+207
| | | | | | | Most of the definitions for WN531A6 will be shared with WN533A8 in a future commit, so put them in a shared DTSI. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-04-234-1/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-04-234-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* ramips: add support for OrayBox X3ARay Wang2022-04-175-0/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: mt7621: make u_env partition r/w for Linksys EA7xxx devicesRussell Morris2022-04-161-1/+0
| | | | | | | | Make u_env partition read/write - currently cannot write to it, which blocks fw_setenv. This in turn breaks features like Advanced Reboot, which rely on setting the environment variable boot_part (1 or 2). Signed-off-by: Russell Morris <rmorris@rkmorris.us>
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-165-131/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-163-0/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-163-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* kernel: bump 5.15 to 5.15.33Rui Salvaterra2022-04-091-21/+21
| | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch [1] generic/backport-5.15/730-v5.16-hv-utils-add-PTP_1588_CLOCK-to-Kconfig-to-fix-build.patch [2] generic/pending-5.15/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch [3] generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch [4] Manually rebased: generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch ramips/patches-5.15/710-at803x.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d29cda15cab086d82d692de016f7249545d4b6b4 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8 [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=ed750e22e44366e264bcdf7b1cf0713f08f7980a [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=0fe94b84c43cfea867e1721606185e8686d7d32f Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [Refresh patches again] [Remove generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: move some symbols to generic configAleksander Jan Bajkowski2022-04-091-8/+0
| | | | | | | | | | | | | | | | | | | This commit add some enabled symbols to generic config. LTO is only supported by clang compiler and therefore should be disabled in the generic config instead of duplicating this symbol in each target. CONFIG_LTO_NONE do this job. The second group of symbols is enabled by the options available in the generic config and is therefore added here: * CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX, * CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL, * CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET. The other symbols are disabled and should be in the generic config. This commit also removes these symbols from subtargets. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: bump 5.10 to 5.10.109John Audia2022-03-301-2/+2
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: fix kernel module build errors on linux 5.15Felix Fietkau2022-03-282-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add linux 5.15 support for mt7621Felix Fietkau2022-03-2743-2/+6804
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add patches for MT7622 WED (wireless ethernet dispatch)Felix Fietkau2022-03-271-2/+2
| | | | | | This series also contains other improvement for hardware flow offload support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix wifi mac address of HiWiFi series devicesShiji Yang2022-03-263-0/+55
| | | | | | | | | | | | | | | | | | For HiWiFi series devices, label_mac can be read from bdinfo partition, and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's label_mac start with D4:EE) For example: label D4:EE:07:32:84:88 lan D4:EE:07:32:84:88 wan D4:EE:07:32:84:89 wlan2g D4:EE:07:32:84:88 wlan5g D0:EE:07:32:84:88 Tested on HiWiFi HC5661. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: skip bbt scan on mt7621Felix Fietkau2022-03-251-1/+1
| | | | | | reduces unnecessary flash reads and speeds up boot time Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: enable support for mtk_bmt in the nand flash driverFelix Fietkau2022-03-251-0/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621_nand: initialize ECC_FDMADDRFelix Fietkau2022-03-251-0/+4
| | | | | | This is needed for the ECC controller to access FDM data Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621_nand: reduce log verbosityStijn Tintel2022-03-251-1/+1
| | | | | | | | | Avoid flooding the log with the message below by increasing the log level to debug: mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: move mt7621_nand driver to filesStijn Tintel2022-03-252-1356/+1353
| | | | | | | | | | | The patch was rejected by upstream. The mtk_nand driver should be modified to support the mt7621 flash controller instead. As there is no newer version to backport, or no upstream version to fix bugs, let's move the driver to the files dir under the ramips target. This makes it easier to make changes to the driver while waiting for mt7621 support to land in mtk_nand. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for D-Link DIR-878 R1Igor Nazarov2022-03-192-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) - Switch: 1 WAN, 4 LAN (Gigabit) - Buttons: Reset, WiFi Toggle, WPS - LEDs: Power, Internet, WiFi 2.4G WiFi 5G The R1 revision is identical to the A1 revision except - No Config2 Parition, therefore - factory partition resized to 64k from 128K - Firmware partition offset is 0x50000 not 0x60000 - Firmware partitions size increased by 64K - Firmware partition type is "denx,uimage", not "sge,uimage" - Padding of image creation "uimage-padhdr 96" removed Installation: Update to the last D-Link firmware through web-ui before OpenWRT installation then follow the instructions to patch your device using D-Link FailsafeUI. - D-Link FailsafeUI: Power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing, then jack into any lan port and manually assign a static IP address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2) and go to http://192.168.0.1 Flash with the factory image. Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-196-0/+252
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Netgear WN3100RPv2Rodolphe de Saint Léger2022-03-166-155/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* Revert "ramips: add support for Netgear WN3000RPv3"Sungbo Eo2022-03-166-186/+155
| | | | | | | | | This reverts commit 7bc20cb6143e089fae6ad4b173fc42b55bdbecfe. It adds support for Netgear WN3100RPv2, but the commit title is wrong. It will be re-added with the correct title. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Netgear WN3000RPv3Rodolphe de Saint Léger2022-03-166-155/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: Add support for D-Link DWR-961 A1Pawel Dembicki2022-03-168-172/+273
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-961 A1 Wireless Router is based on the MT7620A SoC. It's a merge of two Amit boards: DWR-960 with ethernet part of Lava LR-25G001. ROMID it's taken from Telenor branded version and it works with tested device. Images from D-Link site for this router are from DWR-953 and it have ROMID DLK6E2424001. I don't know if it's mistake on web-site or if it's will require different image. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612 mpcie card) - 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem cat 6 - UART (J5) header on PCB (57600 8n1) - 13x LED, 2x button - JBOOT bootloader Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: Apply pinctrl DTS changes to TL-WPA8631PJoe Mullally2022-03-131-9/+13
| | | | | | | | | Applies changes from 7774b86019 to new device committed later. Fix some whitespace in the DTS. Use standard model name format in DTS. Fixes: 6c743c3006f9 ("ramips: Add support for TP-Link TL-WPA8631P v3") Signed-off-by: Joe Mullally <jwmullally@gmail.com> Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: update WLAN MAC address of JCG Y2Chukun Pan2022-03-131-0/+4
| | | | | | | | MAC addresses on OEM firmware: 04:xx:xx:xx:xx:c8 factory 0x4 wlan2g 06:xx:xx:xx:xx:c8 [not on flash] wlan5g Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: update WLAN MAC address of Phicomm K2PChukun Pan2022-03-132-2/+13
| | | | | | | The wireless mac address difference of this machine is similar to that of D-Link DIR-853-R1, so use the same practice. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: Add support for Dual-Q H721Dawsen Gao2022-03-132-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dual-Q H721 is a router platform board, it is the smaller model of the U7621-06. The device has the following specifications: MT7621AT (880 MHz) 256 of RAM (DDR3) 16 MB of FLASH (MX25l12805d SPI) 5x 1 Gbps Ethernet (MT7621 built-in switch) 1x M.2 (NGFF) 3.7V 3A max for 5G M.2 Modem work at USB3.0 mode 1x Minipcie 3.7V 3A max for LTE Modem work at USB2.0 Mode 2x Minipcie for WIFI card 4x Lan+1x Wan 10/100M/1000M RJ45 port 14x LEDs (1x GPIO-controlled) 1x reset button 1x UART header (4-pins) 1x mico SD-card reader 1x DC jack for main power (5~27 V) The following has been tested and is working: Ethernet switch miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) miniSIM slot (works with normal size simcard) sysupgrade reset button micro SD-card reader Installation: This board has no locked down bootloader. The seller can be asked to install openwrt, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. Signed-off-by: Dawsen Gao <dawsen_gao@163.com> [change author name (used SoB one), add ethernet pinctrl, apply sorting to device recipe] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: allow USB power control on TP-Link MR3020v3Dmitry Chigiryov2022-03-091-1/+12
| | | | | | | | | | | | | By switching EPHY_LED4_N_JTRST_N from EPHY_LED4_N to GPIO#39 we can control USB port power an all current revisions of MR3020v3. It was not a thing on some first revisions, pin was unused. But for now on all current MR3020v3 boards EPHY_LED4_N_JTRST_N pin is connected to USB power key. Also it was not used as EPHY indicator on any revision of the board. Signed-off-by: Dmitry Chigiryov <dmitry.chigiryov@ya.ru> [changed author address (used SoB one)] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix DEVICE_VENDOR for unbranded devicesSungbo Eo2022-03-095-9/+9
| | | | | | | | | | | | | | | In commit ee66fe4ea9a6 ("ramips: convert DEVICE_TITLE to new variables"), DEVICE_VENDOR of some unbranded devices were set incorrectly: * WR512-3GN is not a dev board from Ralink. * "XDX-RN502J" is the whole model name and should be not split. This patch sets their DEVICE_VENDOR to "Unbranded", and changes their DTS model properties accordingly. Ref: d0bf15f23595 ("ramips: add support for A5-V11 board (resubmit)") Ref: 9085b05d9e71 ("ramips: rt305x: support for wr512-3gn-like routers") Ref: 0e486d2fd297 ("ramips: add support for unbranded XDX-RN502J board") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7621: add support for Zbtlink ZBT-WG1608Kim Namu2022-03-094-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim Namu <namu@theseed.io>
* ramips: add support for Asus RT-AC1200Ray Wang2022-03-093-26/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: add support for Renkforce WS-WN530HP3-ABirger Koblitz2022-03-083-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Renkforce WS-WN530HP3-A ceiling- mountable Wireless Access Point, which is powered over PoE. Hardware: - SoC: Mediatek MT7621DAT - RAM: 128MiB on SoC - Flash: 16MiB GigaDevice GD25Q128C - 2.4Ghz Wifi: Mediatek MT603EN - 5GHz Wifi: MT613BEN - Ethernet: - 1x 1GBit WAN port, passive PoE capable - 2x 1GBit LAN ports LEDs: 1x Bi-Color LED (red/blue) Buttons: 1x Reset Button, 1x Power Button Installation: Power on the access point and immedately press the reset button for 10 seconds. Connect web-browser to 192.168.10.1 and upload sysupgrade image. Flash uploaded image and wait about 2 minutes for reboot. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
* ramips: use parser_trx for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-062-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WCR-1166DS uses trx-fomatted firmware and the custom magic number (0x5C436F74, "\Cot") is required for OpenWrt installation from OEM WebUI. But the current mtdsplit_trx doesn't support the custom magic number and fail to parse and split to kernel and rootfs when the factory image is flashed. Then, the kernel fails to mount rootfs automatically and panics. Before the commit fddc78bc116bc043fb5cd92dbc45cfd054c21af8, mtdsplit_trx was patched in ramips target and the device-specific magic number was supported only for WCR-1166DS[1]. But the patch was not inherited to the later version of the kernel and deleted by the above commit, then, the custom magic number support was broken. [1]: https://github.com/openwrt/openwrt/blob/05d6e92594c507dcd1f4be6c1bcb2282fe1abe1f/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch#L27 log (factory image): [ 1.165312] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 1.195782] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.205353] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.217938] Creating 7 MTD partitions on "spi0.0": [ 1.227436] 0x000000000000-0x000000030000 : "u-boot" [ 1.238427] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.250123] 0x000000040000-0x000000050000 : "factory" [ 1.261306] 0x000000050000-0x000000810000 : "firmware" [ 1.282051] 0x000000810000-0x000000fd0000 : "firmware2" [ 1.293594] 0x000000fd0000-0x000000fe0000 : "glbcfg" [ 1.304719] 0x000000fe0000-0x000000ff0000 : "board_data" ... [ 1.452424] /dev/root: Can't open blockdev [ 1.460619] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 1.475434] Please append a correct "root=" boot option; here are the available partitions: [ 1.491986] 1f00 192 mtdblock0 [ 1.491989] (driver?) [ 1.504938] 1f01 64 mtdblock1 [ 1.504941] (driver?) [ 1.517885] 1f02 64 mtdblock2 [ 1.517888] (driver?) [ 1.530831] 1f03 7936 mtdblock3 [ 1.530834] (driver?) [ 1.543777] 1f04 7936 mtdblock4 [ 1.543781] (driver?) [ 1.556724] 1f05 64 mtdblock5 [ 1.556727] (driver?) [ 1.569672] 1f06 64 mtdblock6 [ 1.569675] (driver?) [ 1.582617] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 1.598976] Rebooting in 1 seconds.. This patch fixes this issue by using parser_trx with specifying custom magic number in dts instead of mtdsplit_trx. log (fixed factory image): [ 1.202044] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 1.225369] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.235015] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.247603] Creating 7 MTD partitions on "spi0.0": [ 1.257106] 0x000000000000-0x000000030000 : "u-boot" [ 1.269447] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.281192] 0x000000040000-0x000000050000 : "factory" [ 1.294208] 0x000000050000-0x000000810000 : "firmware" [ 1.305774] 2 trx partitions found on MTD device firmware [ 1.316540] Creating 2 MTD partitions on "firmware": [ 1.326399] 0x00000000001c-0x000000214754 : "linux" [ 1.336063] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only [ 1.357070] 0x000000214754-0x0000007c0000 : "rootfs" [ 1.366994] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.386368] mtd: device 5 (rootfs) set to be root filesystem [ 1.398700] 1 squashfs-split partitions found on MTD device rootfs [ 1.411027] 0x000000520000-0x0000007c0000 : "rootfs_data" [ 1.422841] 0x000000810000-0x000000fd0000 : "firmware2" [ 1.436282] 0x000000fd0000-0x000000fe0000 : "glbcfg" [ 1.447408] 0x000000fe0000-0x000000ff0000 : "board_data" ... [ 1.611216] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: switch parser of trx for mt76x8 subtargetINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | | | | This patch enable parser_trx and disable mtdsplit_trx for mt76x8 subtarget. The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget and the parser need to be switched to parser_trx to use the custom magic number in the header for WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update MAC address configuration for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-2/+2
| | | | | | | | This patch converts MAC address configuration of Buffalo WCR-1166DS in 02_network to use the generic function of OpenWrt. And also, add label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: increase spi frequency for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | Use higher frequency than current and up the speed to access to the flash on WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-18 05:22:33 +0000