aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add Unielec U7621-06 32M build targetIgnas Poklad2023-01-052-0/+90
| | | | | | | | | Add 32M build target Rest of the details as per commit 46ab81e405d2 ("ramips add support for UniElec U7621-06") Signed-off-by: Ignas Poklad <ignas2526@gmail.com>
* ramips: enable Wi-Fi LED support for Afoundry EW1200Shiji Yang2023-01-041-2/+14
| | | | | | Add LED properties to PCIe node to enable Wi-Fi LED support. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: enable Wi-Fi LED support for Zbtlink ZBT-WE1326Shiji Yang2023-01-041-2/+14
| | | | | | Add LED properties to PCIe node to enable Wi-Fi LED support. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add basic support for tp-link er605-v2Nikolay Martynov2023-01-044-0/+213
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port. The board has headers to attach console. In order for them to work two solder bridges near those pads need to be made. The defice has the following partition table: ``` 0x000000000000-0x000000080000 : "u-boot" 0x000000080000-0x000000100000 : "u-boot-env" 0x000000100000-0x000000140000 : "factory" 0x000000140000-0x000007e00000 : "firmware" 0x000007e00000-0x000008000000 : "panic-ops" ``` `firmware` partition contains UBI volumes. Unfortunately I accidentally wiped partition and I no longer have access to it. `firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot. It also contains various configuration partitions that include device info and MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes. U-boot has `mtkupgrade` command that just overrides data on firmware partitions. Firmware file provided by TP-Link cannot be used with that command. U-boot also has 'recovery' http server. Unfortunately I was not able to make it work with manufacturer's firmware. Manufacturer's firmware essentially contains multiple UBI volumes along with 'partition table'. Unfortunately I no longer can properly run manufacturer's firmware so I cannot at the moment try to a support for building 'factory' images. This patch adds support for initramfs image as well as sysupgrade image. This seems to be pretty standard MT7621 board otherwise. Things that work: * network * leds * usb * factory MAC detection Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
* ramips: add missing LEDs to Asus RT-AX53UMarian Sarcinschi2023-01-043-3/+19
| | | | | | | | | | | | | | | | This patch adds the missing LEDs to Asus RT-AX53U. Based on PR #10400 and patch provided in #11068 - enable the two LEDs controlled by mt7915e for wireless; - add label to power LED so it works properly and fix formatting; - add the USB LED; - switch LEDs are best left to be controlled by hardware for now. Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com> Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Co-Authored-By: Hartmut Birr <e9hack@gmail.com> Tested-by: Felix Baumann <felix.bau@gmx.de> Tested-by: Marian Sarcinschi <znevna@gmail.com> Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
* kernel: bump 5.15 to 5.15.86John Audia2023-01-033-22/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1] ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2] bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3] Manually rebased: ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4] Added patch/backported: ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a 4. Quilt gave this output when I applied the patch to rebase it: % quilt push -f Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch patching file arch/mips/ralink/Kconfig patching file drivers/pci/controller/Kconfig patching file drivers/pci/controller/Makefile patching file drivers/staging/Kconfig patching file drivers/staging/Makefile patching file drivers/staging/mt7621-pci/Kconfig patching file drivers/staging/mt7621-pci/Makefile patching file drivers/staging/mt7621-pci/TODO patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt patching file drivers/staging/mt7621-pci/pci-mt7621.c Hunk #1 FAILED at 1. Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch 1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej patching file drivers/pci/controller/pcie-mt7621.c Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh) Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c but upstream's version was not an exact match. I opted to delete that file. 5. Suggestion by hauke: https://github.com/torvalds/linux/commit/19098934f910b4d47cb30251dd39ffa57bef9523 "This patch is in upstream kernel, but it was backported to the old staging driver in kernel 5.15." Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: enable BBT on NAND in I-O DATA devicesINAGAKI Hiroshi2022-12-302-0/+10
| | | | | | | | | | | This patch enables MediaTek NAND BBT on I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.). [WN-AX2033GR] Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [WN-AX1167GR2, WN-DX1167R, WN-DX1200GR, WN-DX2033GR] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Refresh patchesHauke Mehrtens2022-12-291-2/+2
| | | | | | The patch was not applying cleanly any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for read/write uboot env to Asus RX-AX53UFelix Baumann2022-12-281-2/+11
| | | | | | | | | | | | | | | | | | Add support for read/writing uboot env by renaming the second partition to its stock label "nvram" and remove the deemed unnecessary "read-only". Split the first partition "u-boot" in two, in order to allow `fw_setenv` safe write-access to the uboot environment variables. This implements hauke's request from [1]. Based on the patch provided by Shiji Yang. [1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224 Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Signed-off-by: Felix Baumann <felix.bau@gmx.de> [ improve commit title and description, fix some whitespace problem ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: Fix drivers/pwm/pwm-mediatek-ramips.c compileHauke Mehrtens2022-12-231-2/+4
| | | | | | | The pwmchip_remove() function returns void now. Fix a compile problem in the drivers/pwm/pwm-mediatek-ramips.c driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Move CONFIG_PWM_IMG and CONFIG_PWM_MEDIATEK to generic configurationHauke Mehrtens2022-12-231-1/+0
| | | | | | | In the build of the ramips/mt76x8 target the user gets asked about these two configuration options, add them to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for Linksys E5400 and clonesJulien Dusser2022-12-183-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350 with the same hardware, but software speed limitations in vendor firmwares. Specification: * SoC: MT7628AN (580 MHz) * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * UART: * 115200, 8N1, 3.3V (real u-boot speed: 119050) * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND) Flash Layout: 0x0000000-0x0030000 : "Bootloader" 0x0030000-0x0040000 : "Config" 0x0040000-0x0050000 : "Factory" 0x0050000-0x0ff0000 : "Kernel" 0x0ff0000-0x1000000 : "CBTinfo" MAC address: LAN: factory 0x28 WAN: LAN + 1 2.4G: LAN + 2 5G: LAN + 3 Installation: 1. Connect to UART, use LF as EOL (not CRLF) 2. Set IP address - Press 4 during boot - setenv serverip <TFTPSERVER_IP> - setenv ipaddr <DEVICE_IP> - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin - saveenv - reset 3. Load Openwrt Kernel image from TFTP: - Press 1 during boot - IP and filename should be already set 4. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Julien Dusser <julien.dusser@free.fr>
* ramips: add support for SNR-CPE-W4N-MT routerAlexey Bartenev2022-12-174-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General specification: - SoC Type: MediaTek MT7620N (580MHz) - ROM: 8 MB SPI-NOR (W25Q64FV) - RAM: 64 MB DDR (M13S5121632A) - Switch: MediaTek MT7530 - Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) - Wireless 2.4 GHz: b/g/n - Buttons: 1 button (RESET) - Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5 - Power: 12 VDC, 1.0 A Flash by the native uploader in 2 stages: 1. Use the native uploader to flash an initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by "Administration/Management/Firmware update/Choose File" in vendor's web interface (ip: 192.168.1.10, login: Admin, password: Admin). Wait ~160 seconds. 2. Flash a sysupgrade image via the initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin file by "System/Backup/Flash Firmware/Flash image..." in LuCI web interface (ip: 192.168.1.1, login: root, no password). Wait ~240 seconds. Flash by U-Boot TFTP method: 1. Configure your PC with IP 192.168.1.131 2. Set up TFTP server and put the openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin image on your PC 3. Connect serial port (57600 8N1) and turn on the router. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.131) ==:192.168.1.131 Input Linux Kernel filename () ==: openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Bartenev <41exey@proton.me>
* ramips: improve support for SIM SIMAX1800T and Haier HAR-20S2U1Shiji Yang2022-12-172-11/+13
| | | | | | | | | | | | | | 1. Use ARTIFACTS to build factory image. This change allows users to generate initramfs factory image using OpenWrt ImageBuilder. 2. Override the default bootargs property defined in "mt7621.dtsi". Although we use the "bootargs-override" property to set bootargs, the default "bootargs" property will still be written into the device tree, so it is better to override it. Tested on SIM SIMAX1800T Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: improve support for H3C TX180x series devicesShiji Yang2022-12-171-0/+8
| | | | | | | | | | | 1. Explicitly declare gpio pin groups to ensure that gpio works properly. 2. Override bootargs in device tree to avoid modifying u-boot envs during initial installation. Tested on H3C TX1801 Plus Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Etisalat S3Mikhail Zhilkin2022-12-135-3/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1x USB3.0 Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface under admin account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following line: <PARAMETER name="Password" type="string" value="<your router serial \ is here>" writable="1" encryption="1" password="1"/> 5. Insert the following line after and save: <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where ETxxxxxxxxxx is the serial number from the backplate label) 9. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 12. Connect to the router using SSH shell under SuperUser account 13. Run in SSH shell: sh 14. Make a mtd backup (optional, see related section) 15. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 16. Login to the router web interface under admin account 17. Remove dots from the OpenWrt factory image filename 18. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:50 | | WAN | label + 11 | *:5b | | 2g | label + 2 | *:52 | | 5g | label + 3 | *:53 | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Co-authored-by: Karim Dehouche <karimdplay@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* kernel: bump 5.10 to 5.10.157John Audia2022-12-111-2/+2
| | | | | | | | | | | | | | | Manually rebased: backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch Removed upstreamed: pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.82John Audia2022-12-111-1/+1
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.81John Audia2022-12-111-2/+2
| | | | | | | | | | | | | | | | | | | | Manually rebased: backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1] Removed upstreamed: pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2] All other patches automatically rebased 1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk> 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-073-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: define loadaddr for all UniFi devicesDavid Bauer2022-12-071-0/+2
| | | | | | | | Define the load-address for the DTB of all Ubiquiti UniFi devices using FIT images. From the GPL code we can assume these boards are affected by the same relocating issue with the vendor bootloader. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7621: enable lzma-loader for netis WF2881Joonhyuk Song2022-12-061-1/+2
| | | | | | Fixes boot loader LZMA decompression issues (LZMA ERROR 1) Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
* ramips: mt7621: mikrotik 760igs (hEX S) fix SFPJohn Thomson2022-12-061-0/+1
| | | | | | | | | | | | | This device uses an AR8031/AR8033 chip to convert SoC gmac1 RGMII to 1000base-x or sgmii for the SFP fibre cage. The SFP cage requires phy-mode rgmii-rxid, and without it will not recieve any packets: ethtool -S sfp rx_fcs_errors will increase when packets should be being received, but no other _rx counters will change. Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GRINAGAKI Hiroshi2022-12-051-19/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use ARTIFACTS to generate initramfs-based factory image of I-O DATA WN-AX1167GR instead of redundant recipe which generate on KERNEL_INITRAMFS. Note: WN-AX1167GR has 2x OS images on stock firmware. stock log: flash manufacture id: c2, device id 20 18 MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" 1st image is "Kernel" and 2nd is "app" when booted from 1st image. In OpenWrt, those 2x partitions are combined to "firmware" with undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff). The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so check-size for initramfs-factory image needs to be called with the size. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for HiWiFi HC5611Senis John2022-12-045-0/+44
| | | | | | | | | | | | | | | | | | | | | | | CPU: MediaTek MT7628AN @ 575 MHz Flash: 16 MB RAM: 128 MB Ethernet: 10/100Mbps x 1 Wlan: 300 Mbps USB: USB 2.0 x 1 LED: red/green x 1 Button: reset x 1 1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh 2. Upload the openwrt firmware to the router via SCP 3. Login the router via SSH 4. Run `mtd -r write path_to_firmware.bin firmware` I have tested on my device. - The LED will display RED on power-on, After system start completed, trun GREEN - Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device - USB can working under official u-boot Signed-off-by: Senis John <thank243@gmail.com>
* ramips: mt7621: enable lzma-loader for ZyXEL WAP6805Bjørn Mork2022-12-031-1/+2
| | | | | | | Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover". Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622Felix Fietkau2022-11-251-2/+2
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for Keenetic KN-3010Maxim Anisimov2022-11-203-0/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT. Specification: - System-On-Chip: MT7621DAT - CPU/Speed: 880 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100/1000 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn - Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac - 4x LED, 2x button, 1x mode switch Notes: - The device supports dual boot mode - The firmware partitions were concatinated into one - The FN button led indicator has been reassigned as the 2.4GHz wifi indicator. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin" to "KN-3010_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* treewide: uniform vendor name for ASUSMoritz Warning2022-11-165-18/+18
| | | | | | | Their own website (https://www.asus.com) always uses the upper case style name. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* ramips: Add support for D-Link DIR-3060 A1Ivaylo Ivanov2022-11-134-0/+253
| | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1/ Use the provided emergency web GUI to upload and flash a new firmware to the device Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
* ramips: add support for Amped Wireless B1200EXDaniel Fuchs2022-11-137-32/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is almost identical to the already supported Edimax EW-7476RP5, the only differences are: - There is no mode selection slider switch on this device - The two wireless LEDs are green instead of blue - Model name in the CSYS header is RN10 Additional changes: - Moved WiFi LEDs and the slider switch to the individual dt files - Added ieee80211-freq-limit to the mt7612e radio to properly disable 2.4GHz band on this radio Device specifications: SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS/RESET LED: - WiFi 5G (green) - WiFi 2.4G (green) - Signal Strength (green) - Power (green) - WPS (green) - LAN (green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the WPS button 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: Upload the sysupgrade image via the default web interface Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
* ramips: add support for Rostelecom RT-SF-1Mikhail Zhilkin2022-11-135-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 ZigBee: 3.0, EFR32 MG1B232GG Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Remove dots from the OpenWrt factory image filename 2. Login to the router web interface 3. Update firmware using web interface with the OpenWrt factory image 4. If OpenWrt is booted, then no further steps are required. Enjoy! Otherwise (Stock firmware has booted again) proceed to the next step. 5. Update firmware using web interface with any version of the Stock firmware 6. Update firmware using web interface with the OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+------------+ | use | address | example | +-----+------------+------------+ | LAN | label | *:72, *:d2 | | WAN | label + 11 | *:7d, *:dd | | 2g | label + 2 | *:74, *:d4 | | 5g | label + 3 | *:75, *:d5 | +-----+------------+------------+ The label MAC address was found in Factory 0x21000 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create common dtsi for Sercomm Dxx routersMikhail Zhilkin2022-11-132-225/+240
| | | | | | | | | | | This commit adds common dtsi for the following Sercomm devices with 256 MB NAND: Beeline Smartbox TURBO (Sercomm DF3) Rostelecom RT-SF-1 (Sercomm DKG) Also fixed typo ("Container" mtd name should be with a capital). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIOMartin Dziura2022-11-131-5/+1
| | | | | | | This is explicitly intended by the official documentation at https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout Signed-off-by: Martin Dziura <m.dziura@tum.de>
* ramips: fix MAC address assignment for rt1800, e7350Arne Zachlod2022-11-131-0/+1
| | | | | | | | previous commit ffa4b5283b introduced a bug which broke the MAC address assignment for belkin,rt1800 and linksys,e7350. Fixes: ffa4b5283b39 ("ramips: add support for Mikrotik LtAP-2HnD") Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ramips: add support for Cudy WR1300 v2Óscar García Amor2022-11-123-4/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7613BE - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS - Power: DC 12V 1A tip positive Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
* ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1Szabolcs Hubai2022-11-121-4/+1
| | | | | | | | | | | | | | Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating "uimage-lzma-loader". While reviewing my original submission of commit ce1957100411 David suggested to use $(Device/uimage-lzma-loader), but due to the specific needs of the vendor bootloader that simple oneliner didn't work. The new $(Device/seama-lzma-loader) is for those SEAMA capable bootloaders. Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: rt3883: use seama-lzma-loader for D-Link DIR-645Szabolcs Hubai2022-11-121-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the support topic [0] of the GitHub issue #10634 it was found out (based on boot logs) that the uimage-lzma-loader (commit 09faa73c53bd) never worked, as an earlier workaround (commit 6fba88de1913) negated the recipe: 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 .raspi_read: from:50000 len:c .raspi_read: from:50000 len:1fa000 ................................We have SEAMA, Image Size = 2072512 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022 [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5 [ 0.000000] printk: bootconsolde [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is D-Link DIR-645 [ 0.000000] Initrd not found or empty - disabling initrd Using the new seama-lzma-loader it's able to boot OpenWrt 22.03 and OpenWrt SNAPSHOT too: 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 .raspi_read: from:50000 len:c .raspi_read: from:50000 len:48b004 .........................................................................We have SEAMA, Image Size = 4763588 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80000000... [ 0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022 [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is D-Link DIR-645 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 The OKLI Loader is unable to read the flash on this SoC: Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000) 0: https://forum.openwrt.org/t/136435 Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645") Fixes: 09faa73c53bd ("ramips: rt3883: use lzma-loader for DIR-645") Tested-by: Glenn Fowler <gfowler1@outlook.com> Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: define lzma-loader recipe for SEAMA devicesSzabolcs Hubai2022-11-121-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define "Device/seama-lzma-loader" recipe for SEAMA devices to help contributors avoid doing recipe mistakes. In a forum topic [0] I was under the impression that the good old uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device. It was found out, that the uimage-lzma-loader never worked because the KERNEL variable was overriden earlier (also an LZMA ERROR 1 related commit, 6fba88de1913), and the "use lzma-loader" fix (commit 09faa73c53bd) didn't catch that to include the "loader-kernel" part. I contributed an LZMA ERROR 1 fix (commit ce1957100411) for the SEAMA device D-Link DIR-860L B1, where I had to duplicate the whole uimage-lzma-loader recipe because of the special needs of the vendor bootloader. This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to avoid duplication. It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to boot from flash, and it's compatible with D-Link DIR-645 too. It repacks lzma-loader with lzma for kernel (without uImage), because these weird hacked vendor bootloaders accepts only LZMA compressed kernels from flash: We have SEAMA, Image Size = 4759794 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK It uses uImage header for initramfs kernel to be little bit verbose. 0: https://forum.openwrt.org/t/136435/10 Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: add support for Mikrotik LtAP-2HnDArne Zachlod2022-11-126-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS receiver and two mPCIe slots. Specifications: * SoC: MT7621A * RAM: 128 MiB Nanya NT5CC64M16GP-DI * Flash: 16 MiB winbond W25Q128JV * WLAN: * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas, with RF switches for external connectors) * Ethernet: 1 Gbps, single port * USB Host: USB 2.0 Speeds * Serial: 115200 baud * LEDs: Power, System, GPS, 5* RSSI * mPCIe: * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host) * miniPCIe slot 2: USB 2.0 and 3.0 * SIM Cards: * Slot 1 Connected to mPCIe slot 1 * Slot 2 and 3 connected to mPCIe slot 2 via switch * GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14 gpios are exposed to /sys/class/gpio: * usb-select: swithes USB 2.0 interface between external port and internal mPCIe slot 1 default is the external USB interface * gps-reset: resets the GPS interface chip * sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2 * gps-ant-select: switches GPS antenna between internal antenna and SMA connected antenna * lte-reset: resets mPCIe slot 2 Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* kernel: more fixes for mtk_eth_soc performance optimizationFelix Fietkau2022-11-101-2/+2
| | | | | | | | - fix features sync between netdevs - fix crash in dsa_switch_rcv Fixes: ceb1451c10c1 ("kernel: add mediatek soc ethernet performance improvements") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add mediatek soc ethernet performance improvementsFelix Fietkau2022-11-091-4/+4
| | | | | | | | - implement multiqueue via qdma hardware shaper to deal with ports with different speeds - implement hardware DSA untagging - add NETIF_F_ALL_TSO to reduce unnecessary segmentation Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: define loadaddr for U6 Lite DTBDavid Bauer2022-11-081-0/+1
| | | | | | | | | | | | | The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always setting fdt_high to 0xffffffff when invoking the bootubnt command. Work around this issue by loading the DTB to a valid,aligned address, so the bootloader does not have to relocate the FDT automatically. Note: The device does read the kernel before invoking bootm on the FIT image to 0x86000000. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: gl-mt1300: downclock SPI to 50MHzMichael Lyle2022-11-071-2/+1
| | | | | | | | | | | | | | | The SPI max frequency was set to 80MHz, considerably higher than the vendor clocks it in their firmware (10MHz). Multiple users reported jffs2 corruption/instability in GitHub issue #10461. My unit has a W25Q256; datasheet specifies maximum SPI frequency for read command of 50MHz. Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read; and @MPannen1979 for identifying the problem. Fixes: #10461 Signed-off-by: Michael Lyle <mlyle@lyle.org>
* ramips: fix TP-Link RE200 v3/v4 LEDsSungbo Eo2022-11-075-11/+54
| | | | | | | | | | | | Set power LED to gpio 43 instead of 44 for v3 and v4. Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`). Tested by the author of the initial v3 and v4 commit. Reported-by: Richard Fröhning <misanthropos@gmx.de> Tested-by: Richard Fröhning <misanthropos@gmx.de> Signed-off-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ramips: add support for TP-Link MR600 V2(EU)Linos Giannopoulos2022-11-054-0/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation etc. and can reportedly achieve higher bandwidth with it. - Specifications: * SoC: Mediatek MT7621DAT 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (GD25Q128C) * LTE Modem: Qualcomm MDM9240 * WiFi 5GHz: Mediatek MT7613BEN * WiFi 2.4GHz: Mediatek MT7603EN * Ethernet: MT7530, 4x 1000Base-T. * UART: Serial console (115200 8n1), J1(GND:3) * Buttons: Reset, WPS. * LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2, Signal3 - MAC Addresses: OEM firmware configuration: 54:af:97:xx:xx:7b : 2.4G 54:af:97:xx:xx:7a : 5G 54:af:97:xx:xx:7c : LTE 54:af:97:xx:xx:7b : LAN (label) 54:af:97:xx:xx:7c : WAN - Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to openwrt.img Configure the TFTP server to listen at 192.168.0.5/24. 3. Connect to the serial console. Attach power and interrupt the boot procedure when prompted (type `tpl`). Credentials are admin / 1234 4. Configure U-Boot for booting OpenWrt from ram $ tftpboot $ bootm 5. Transfer the OpenWrt sysupgrade image to the device. - LTE: In order to setup the wwan0 interface: 1. Add a `qmi` proto interface under `/etc/config/network`, e.g.: ``` config interface 'wwan0' option device '/dev/cdc-wdm0' option proto 'qmi' option pincode 'XXXX' option apn 'your_isp_apn' ``` 2. Add `wwan0` interface to the `wan` firewall zone 3. `/etc/init.d/network restart` Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
* ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1Shiji Yang2022-11-057-4/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Zbtlink ZBT-WG1602-V04Alexander Horner2022-11-054-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Description heavily based on commit 7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have been removed Completed with great help from \x on IRC. Thanks, \x! Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN (UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe slots with USB and SIM only and another one which is a pure miniPCIe slot as well as five Gigabit Ethernet ports (4xLAN + WAN). Specification: * SoC: MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB * Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2) * WLAN 5GHz: MT7662E (.11nac, MIMO 2x2) * WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios * miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus * WWAN Ants: detachable x4 * External storage: microSD (SDXC) slot * USB: 3.0 Type-A port * LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1 power indicator) * Button: 1 (reset) * UART: console (115200 baud) * Power: DC jack (12 V / 2.5 A) Additional HW information: * SoC USB port 1 is shared by internal miniPCIe slot and external Type-A USB port, USB D+/D- lines are toggled between ports using a GPIO controlled DPDT switch. Installation: The kernel image can be installed directly onto the device via a browser to 192.168.1.1 using the built in firmware recovery Web UI available. It can be accessed by pushing the reset button in, applying power and holding the reset button for approximately 10 seconds. When the kernel image has been flashed, you can access LuCI and upload the sysupgrade as normal. Signed-off-by: Alexander Horner <ahorner@programmer.net>
* ramips: add support for Youku X2Shiji Yang2022-11-054-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: MT7620AN + MT7612EN RAM: 128 MiB DDR2 Flash: 16 MiB (Winbond W25Q28FVFG) WLAN: 2.4G + 5G LAN: LAN ports *2 WAN: WAN port *1 USB: USB2.0 *1 SD Card: MicroSD *1 Buttons: Reset *1 LEDs: ethernet *3, system, usb, wlan2g, wlan5g MAC Address: use address source label 54:36:9b:xx:xx:ac lan lan 54:36:9b:xx:xx:ac factory.0x0028 wan 54:36:9b:xx:xx:ad factory.0x002e wlan2g 54:36:9b:xx:xx:ae factory.0x0004 wlan5g 54:36:9b:xx:xx:af factory.0x8004 Installation: 1. Apply initramfs-kernel.bin in stock firmware Web UI. 2. Install sysupgrade.bin on OpenWrt and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: improve compatibility for Youku YK-L2 and YK-L1 seriesShiji Yang2022-11-054-2/+10
| | | | | | | | | | | | | | Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install initramfs-kernel.bin from the stock firmware Web UI. At the same time, this change makes it possible to boot OpenWrt with the official u-boot. Notice: Since the stock firmware is based on OpenWrt and the configuration will be retained by default during the upgrade process, so we must use initramfs-kernel.bin to do a initial installation. After the system restarts, install sysupgrade.bin and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-29 21:57:38 +0000