aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7621: enable lzma-loader for ZyXEL WAP6805Bjørn Mork2022-12-031-1/+2
| | | | | | | Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover". Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622Felix Fietkau2022-11-251-2/+2
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for Keenetic KN-3010Maxim Anisimov2022-11-203-0/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT. Specification: - System-On-Chip: MT7621DAT - CPU/Speed: 880 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100/1000 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn - Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac - 4x LED, 2x button, 1x mode switch Notes: - The device supports dual boot mode - The firmware partitions were concatinated into one - The FN button led indicator has been reassigned as the 2.4GHz wifi indicator. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin" to "KN-3010_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* treewide: uniform vendor name for ASUSMoritz Warning2022-11-165-18/+18
| | | | | | | Their own website (https://www.asus.com) always uses the upper case style name. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* ramips: Add support for D-Link DIR-3060 A1Ivaylo Ivanov2022-11-134-0/+253
| | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1/ Use the provided emergency web GUI to upload and flash a new firmware to the device Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
* ramips: add support for Amped Wireless B1200EXDaniel Fuchs2022-11-137-32/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is almost identical to the already supported Edimax EW-7476RP5, the only differences are: - There is no mode selection slider switch on this device - The two wireless LEDs are green instead of blue - Model name in the CSYS header is RN10 Additional changes: - Moved WiFi LEDs and the slider switch to the individual dt files - Added ieee80211-freq-limit to the mt7612e radio to properly disable 2.4GHz band on this radio Device specifications: SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS/RESET LED: - WiFi 5G (green) - WiFi 2.4G (green) - Signal Strength (green) - Power (green) - WPS (green) - LAN (green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the WPS button 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: Upload the sysupgrade image via the default web interface Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
* ramips: add support for Rostelecom RT-SF-1Mikhail Zhilkin2022-11-135-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 ZigBee: 3.0, EFR32 MG1B232GG Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Remove dots from the OpenWrt factory image filename 2. Login to the router web interface 3. Update firmware using web interface with the OpenWrt factory image 4. If OpenWrt is booted, then no further steps are required. Enjoy! Otherwise (Stock firmware has booted again) proceed to the next step. 5. Update firmware using web interface with any version of the Stock firmware 6. Update firmware using web interface with the OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+------------+ | use | address | example | +-----+------------+------------+ | LAN | label | *:72, *:d2 | | WAN | label + 11 | *:7d, *:dd | | 2g | label + 2 | *:74, *:d4 | | 5g | label + 3 | *:75, *:d5 | +-----+------------+------------+ The label MAC address was found in Factory 0x21000 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create common dtsi for Sercomm Dxx routersMikhail Zhilkin2022-11-132-225/+240
| | | | | | | | | | | This commit adds common dtsi for the following Sercomm devices with 256 MB NAND: Beeline Smartbox TURBO (Sercomm DF3) Rostelecom RT-SF-1 (Sercomm DKG) Also fixed typo ("Container" mtd name should be with a capital). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIOMartin Dziura2022-11-131-5/+1
| | | | | | | This is explicitly intended by the official documentation at https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout Signed-off-by: Martin Dziura <m.dziura@tum.de>
* ramips: fix MAC address assignment for rt1800, e7350Arne Zachlod2022-11-131-0/+1
| | | | | | | | previous commit ffa4b5283b introduced a bug which broke the MAC address assignment for belkin,rt1800 and linksys,e7350. Fixes: ffa4b5283b39 ("ramips: add support for Mikrotik LtAP-2HnD") Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ramips: add support for Cudy WR1300 v2Óscar García Amor2022-11-123-4/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7613BE - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS - Power: DC 12V 1A tip positive Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
* ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1Szabolcs Hubai2022-11-121-4/+1
| | | | | | | | | | | | | | Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating "uimage-lzma-loader". While reviewing my original submission of commit ce1957100411 David suggested to use $(Device/uimage-lzma-loader), but due to the specific needs of the vendor bootloader that simple oneliner didn't work. The new $(Device/seama-lzma-loader) is for those SEAMA capable bootloaders. Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: rt3883: use seama-lzma-loader for D-Link DIR-645Szabolcs Hubai2022-11-121-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the support topic [0] of the GitHub issue #10634 it was found out (based on boot logs) that the uimage-lzma-loader (commit 09faa73c53bd) never worked, as an earlier workaround (commit 6fba88de1913) negated the recipe: 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 .raspi_read: from:50000 len:c .raspi_read: from:50000 len:1fa000 ................................We have SEAMA, Image Size = 2072512 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022 [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5 [ 0.000000] printk: bootconsolde [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is D-Link DIR-645 [ 0.000000] Initrd not found or empty - disabling initrd Using the new seama-lzma-loader it's able to boot OpenWrt 22.03 and OpenWrt SNAPSHOT too: 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 .raspi_read: from:50000 len:c .raspi_read: from:50000 len:48b004 .........................................................................We have SEAMA, Image Size = 4763588 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80000000... [ 0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022 [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is D-Link DIR-645 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 The OKLI Loader is unable to read the flash on this SoC: Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000) 0: https://forum.openwrt.org/t/136435 Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645") Fixes: 09faa73c53bd ("ramips: rt3883: use lzma-loader for DIR-645") Tested-by: Glenn Fowler <gfowler1@outlook.com> Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: define lzma-loader recipe for SEAMA devicesSzabolcs Hubai2022-11-121-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define "Device/seama-lzma-loader" recipe for SEAMA devices to help contributors avoid doing recipe mistakes. In a forum topic [0] I was under the impression that the good old uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device. It was found out, that the uimage-lzma-loader never worked because the KERNEL variable was overriden earlier (also an LZMA ERROR 1 related commit, 6fba88de1913), and the "use lzma-loader" fix (commit 09faa73c53bd) didn't catch that to include the "loader-kernel" part. I contributed an LZMA ERROR 1 fix (commit ce1957100411) for the SEAMA device D-Link DIR-860L B1, where I had to duplicate the whole uimage-lzma-loader recipe because of the special needs of the vendor bootloader. This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to avoid duplication. It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to boot from flash, and it's compatible with D-Link DIR-645 too. It repacks lzma-loader with lzma for kernel (without uImage), because these weird hacked vendor bootloaders accepts only LZMA compressed kernels from flash: We have SEAMA, Image Size = 4759794 Verifying Checksum ... Uncompressing SEAMA linux.lzma ... OK It uses uImage header for initramfs kernel to be little bit verbose. 0: https://forum.openwrt.org/t/136435/10 Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: add support for Mikrotik LtAP-2HnDArne Zachlod2022-11-126-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS receiver and two mPCIe slots. Specifications: * SoC: MT7621A * RAM: 128 MiB Nanya NT5CC64M16GP-DI * Flash: 16 MiB winbond W25Q128JV * WLAN: * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas, with RF switches for external connectors) * Ethernet: 1 Gbps, single port * USB Host: USB 2.0 Speeds * Serial: 115200 baud * LEDs: Power, System, GPS, 5* RSSI * mPCIe: * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host) * miniPCIe slot 2: USB 2.0 and 3.0 * SIM Cards: * Slot 1 Connected to mPCIe slot 1 * Slot 2 and 3 connected to mPCIe slot 2 via switch * GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14 gpios are exposed to /sys/class/gpio: * usb-select: swithes USB 2.0 interface between external port and internal mPCIe slot 1 default is the external USB interface * gps-reset: resets the GPS interface chip * sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2 * gps-ant-select: switches GPS antenna between internal antenna and SMA connected antenna * lte-reset: resets mPCIe slot 2 Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* kernel: more fixes for mtk_eth_soc performance optimizationFelix Fietkau2022-11-101-2/+2
| | | | | | | | - fix features sync between netdevs - fix crash in dsa_switch_rcv Fixes: ceb1451c10c1 ("kernel: add mediatek soc ethernet performance improvements") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add mediatek soc ethernet performance improvementsFelix Fietkau2022-11-091-4/+4
| | | | | | | | - implement multiqueue via qdma hardware shaper to deal with ports with different speeds - implement hardware DSA untagging - add NETIF_F_ALL_TSO to reduce unnecessary segmentation Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: define loadaddr for U6 Lite DTBDavid Bauer2022-11-081-0/+1
| | | | | | | | | | | | | The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always setting fdt_high to 0xffffffff when invoking the bootubnt command. Work around this issue by loading the DTB to a valid,aligned address, so the bootloader does not have to relocate the FDT automatically. Note: The device does read the kernel before invoking bootm on the FIT image to 0x86000000. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: gl-mt1300: downclock SPI to 50MHzMichael Lyle2022-11-071-2/+1
| | | | | | | | | | | | | | | The SPI max frequency was set to 80MHz, considerably higher than the vendor clocks it in their firmware (10MHz). Multiple users reported jffs2 corruption/instability in GitHub issue #10461. My unit has a W25Q256; datasheet specifies maximum SPI frequency for read command of 50MHz. Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read; and @MPannen1979 for identifying the problem. Fixes: #10461 Signed-off-by: Michael Lyle <mlyle@lyle.org>
* ramips: fix TP-Link RE200 v3/v4 LEDsSungbo Eo2022-11-075-11/+54
| | | | | | | | | | | | Set power LED to gpio 43 instead of 44 for v3 and v4. Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`). Tested by the author of the initial v3 and v4 commit. Reported-by: Richard Fröhning <misanthropos@gmx.de> Tested-by: Richard Fröhning <misanthropos@gmx.de> Signed-off-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ramips: add support for TP-Link MR600 V2(EU)Linos Giannopoulos2022-11-054-0/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation etc. and can reportedly achieve higher bandwidth with it. - Specifications: * SoC: Mediatek MT7621DAT 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (GD25Q128C) * LTE Modem: Qualcomm MDM9240 * WiFi 5GHz: Mediatek MT7613BEN * WiFi 2.4GHz: Mediatek MT7603EN * Ethernet: MT7530, 4x 1000Base-T. * UART: Serial console (115200 8n1), J1(GND:3) * Buttons: Reset, WPS. * LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2, Signal3 - MAC Addresses: OEM firmware configuration: 54:af:97:xx:xx:7b : 2.4G 54:af:97:xx:xx:7a : 5G 54:af:97:xx:xx:7c : LTE 54:af:97:xx:xx:7b : LAN (label) 54:af:97:xx:xx:7c : WAN - Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to openwrt.img Configure the TFTP server to listen at 192.168.0.5/24. 3. Connect to the serial console. Attach power and interrupt the boot procedure when prompted (type `tpl`). Credentials are admin / 1234 4. Configure U-Boot for booting OpenWrt from ram $ tftpboot $ bootm 5. Transfer the OpenWrt sysupgrade image to the device. - LTE: In order to setup the wwan0 interface: 1. Add a `qmi` proto interface under `/etc/config/network`, e.g.: ``` config interface 'wwan0' option device '/dev/cdc-wdm0' option proto 'qmi' option pincode 'XXXX' option apn 'your_isp_apn' ``` 2. Add `wwan0` interface to the `wan` firewall zone 3. `/etc/init.d/network restart` Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
* ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1Shiji Yang2022-11-057-4/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Zbtlink ZBT-WG1602-V04Alexander Horner2022-11-054-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Description heavily based on commit 7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have been removed Completed with great help from \x on IRC. Thanks, \x! Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN (UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe slots with USB and SIM only and another one which is a pure miniPCIe slot as well as five Gigabit Ethernet ports (4xLAN + WAN). Specification: * SoC: MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB * Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2) * WLAN 5GHz: MT7662E (.11nac, MIMO 2x2) * WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios * miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus * WWAN Ants: detachable x4 * External storage: microSD (SDXC) slot * USB: 3.0 Type-A port * LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1 power indicator) * Button: 1 (reset) * UART: console (115200 baud) * Power: DC jack (12 V / 2.5 A) Additional HW information: * SoC USB port 1 is shared by internal miniPCIe slot and external Type-A USB port, USB D+/D- lines are toggled between ports using a GPIO controlled DPDT switch. Installation: The kernel image can be installed directly onto the device via a browser to 192.168.1.1 using the built in firmware recovery Web UI available. It can be accessed by pushing the reset button in, applying power and holding the reset button for approximately 10 seconds. When the kernel image has been flashed, you can access LuCI and upload the sysupgrade as normal. Signed-off-by: Alexander Horner <ahorner@programmer.net>
* ramips: add support for Youku X2Shiji Yang2022-11-054-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: MT7620AN + MT7612EN RAM: 128 MiB DDR2 Flash: 16 MiB (Winbond W25Q28FVFG) WLAN: 2.4G + 5G LAN: LAN ports *2 WAN: WAN port *1 USB: USB2.0 *1 SD Card: MicroSD *1 Buttons: Reset *1 LEDs: ethernet *3, system, usb, wlan2g, wlan5g MAC Address: use address source label 54:36:9b:xx:xx:ac lan lan 54:36:9b:xx:xx:ac factory.0x0028 wan 54:36:9b:xx:xx:ad factory.0x002e wlan2g 54:36:9b:xx:xx:ae factory.0x0004 wlan5g 54:36:9b:xx:xx:af factory.0x8004 Installation: 1. Apply initramfs-kernel.bin in stock firmware Web UI. 2. Install sysupgrade.bin on OpenWrt and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: improve compatibility for Youku YK-L2 and YK-L1 seriesShiji Yang2022-11-054-2/+10
| | | | | | | | | | | | | | Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install initramfs-kernel.bin from the stock firmware Web UI. At the same time, this change makes it possible to boot OpenWrt with the official u-boot. Notice: Since the stock firmware is based on OpenWrt and the configuration will be retained by default during the upgrade process, so we must use initramfs-kernel.bin to do a initial installation. After the system restarts, install sysupgrade.bin and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: bump 5.15 to 5.15.77John Audia2022-11-051-1/+1
| | | | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.153John Audia2022-11-051-1/+1
| | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: add support for YunCore FAP690Volodymyr Puiul2022-10-315-1/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI NOR - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 1x 1GiE via MT7530 - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Bootloader: U-Boot - Buttons: - SW1 - no label on the box, combined with led - Led: Status. RGB controlled by - GPIO 14 - green color - GPIO 15 - red color - GPIO 16 - blue color Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise it will not boot. MAC addresses as verified by OEM firmware: vendor source LAN factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
* ramips: add support for YunCore FAP640Volodymyr Puiul2022-10-303-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Power: 802.11af/at PoE; - Bootloader: U-Boot - Buttons: - Reset - LEDs: - Status - RGB controlled by - GPIO 14 LOW - green color - GPIO 15 LOW- red color - GPIO 16 LOW - blue color - WAN - gren color, controlled by switch GPIO 12 LOW - LAN1 - gren color, controlled by switch GPIO 9 HIGH - LAN2 - gren color, controlled by switch GPIO 6 LOW - LAN3 - gren color, controlled by switch GPIO 3 LOW - LAN4 - gren color, controlled by switch GPIO 0 LOW Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise router will not boot. MAC addresses with OEM firmware: vendor source lan factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
* ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4CShiji Yang2022-10-232-1/+13
| | | | | | The blue WAN LED connected to GPIO37 is missing, so re-add it. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix WAN mac address allocation for Unielec 01 and 06 modelsDavid Bentham2022-10-233-6/+15
| | | | | | | | | | | | | | | | | | | | | | Manufacturer has predetermined mac address values for lan and wan ports. This change keeps inline with other mt7621 devices mac address allocation from factory mtd partition. Example from hexdump output: 0xe000 0x6 (lan) - 0xe006 0x6 (wan) 0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff Previous change had created an overlapping mac address situation as it would increment by one based on the lan mac address location found in the factory partition, which would sometimes increment to the same as the mt7603 wifi chip. Tested on Unielec u7621-01 model Signed-off-by: David Bentham <db260179@gmail.com>
* ramips: rt3883: enable lzma-loader for Belkin F9K1109v1Robert Senderek2022-10-231-1/+1
| | | | | | | Fixes boot loader LZMA decompression issues Fixes: #10968 Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
* ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1Alex Khodin2022-10-231-0/+1
| | | | | | | | Fixes boot loader LZMA decompression issues. Without this change the board end up in a boot loop. Signed-off-by: Alex Khodin <mxktz1@gmail.com>
* ramips: add A-040W-Q alternative name for MSG1500 X.00Chukun Pan2022-10-231-0/+2
| | | | | | | The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are exactly the same, both of which are customized by operators. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic configAleksander Jan Bajkowski2022-10-2112-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should be enabled on target or subtarget based on SoC architecture. Fixes warning: $ make kernel_oldconfig CONFIG_TARGET=subtarget ... .config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state .... Summary: - ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture. If it is disabled then the processor operates in LITTLE_ENDIAN mode (default), - ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This option should be enabled after OpenWRT moves to kernel 6.x. After refreshing the kernel, the symbol disappears, - ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN, - MIPS - enabled relevant symbols, - POWERPC - enabled CONFIG_CPU_BIG_ENDIAN, - UML - Symbols are not defined for this architecture, - X86 - always little endian. Symbols are not defined for this architecture. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ramips: kndrt31r19: set up wan interface by defaultAndrey Butirsky2022-10-191-1/+7
| | | | | | The only WAN port of the device is it's modem, so set it up as such Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* build: move Build/edimax-header to image-commands.mkINAGAKI Hiroshi2022-10-191-5/+0
| | | | | | | | | | To use from the following devices in ath79 target, move edimax-header to image-commands.mk. - ELECOM WRC-300GHBK2-I - ELECOM WRC-1750GHBK2-I/C Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-196-0/+6
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mt7621: netgear_ex6150: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #10645 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: use lzma-loader on JCG Q20Du Cai2022-10-091-0/+1
| | | | | | Fixes the LZMA uncompression issue on JCG Q20. Signed-off-by: Du Cai <caidu@smail.nju.edu.cn>
* kernel: bump 5.15 to 5.15.72John Audia2022-10-091-1/+1
| | | | | | | | | | | | | | | | | Removed upstreamed: generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch[1] bcm53xx/patches-5.15/082-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[2] All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 Run-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 (RB5009UG+S+IN) 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=5de02ab84aeca765da0e4d8e999af35325ac67c2 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=ab5c5787ab5ecdc4a7ea20b4ef542579e1beb49d Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: fix switch setup for ASUS RT-AX53UMatthias Schiffer2022-10-032-5/+1
| | | | | | | The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface corresponding to the non-existing port. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: add support for SNR SNR-CPE-ME2-LiteAlexey Kosmakov2022-10-022-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR SNR-CPE-ME2-Lite is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4 GHz 2T2R (MediaTek MT7603E) 5 GHz 2T2R (MediaTek MT7613BE) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction via WEB (firmware 1.10.4 and later) 1. Boot SNR-CPE-ME2-Lite normally with "Router" mode 2. Access to "http://192.168.1.1/" and open "Administration -> Management" page 3. Select the OpenWrt factory image in "Firmware update" section and click "Update" button 4. Wait ~120 seconds to complete flashing Flash instruction via TFTP (all version): 1. Boot SNR-CPE-ME2-Lite to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Kosmakov <a.kosmakov@nagtech.ru>
* ramips: enable LZMA loader to fix Linksys RE6500 bootMark King2022-10-021-0/+1
| | | | | | | | | | | At some point after 21.02.3 and before 22.03.0, the size limits of the Linksys RE6500 were reached and prevent booting from the 22.03.0 release or builds of current SNAPSHOT. This patch allows builds of master to boot again and has been tested on my device. Fixes: #8577 Signed-off-by: Mark King <mark@vemek.co>
* ramips: add led driver to UniFi FlexHD defaut package setDaniel Golle2022-09-301-1/+1
| | | | | | | Add kmod-leds-ubnt-ledbar to the packages selected by default on the UniFi FlexHD access point. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: move ubnt ledbar driver to a separate packageFelix Fietkau2022-09-302-2/+0
| | | | | | | Simplifies the tree by removing a non-upstream kernel patch and related kconfig symbols Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: update MAC address configuration for Buffalo WSR-1166DHPKazuhiro Ito2022-09-281-2/+2
| | | | | | | | | | | | Convert MAC address and label_mac configuration of Buffalo WSR-1166DHP to use the generic function of OpenWrt. Apply commit 770cfe9 for WCR-1166DS to WSR-1166DHP too. Tested on the device and MAC address is kept before and after this change. Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
* kernel: pick patches for MediaTek Ethernet from linux-nextDaniel Golle2022-09-221-2/+2
| | | | | | | | | | | | | | | | | | | Pick patches with several fixes and improvements, preparation for upcoming WED (TX) [1] as well as basic XDP support [2] with MediaTek's Filogic SoCs to the mtk_eth_soc driver. Also pick follow-up patch fixing Ethernet on MT7621 [3]. Tested on Bananapi BPi-R3 (MT7986), Bananapi BPi-R64 (MT7622), Bananapi BPi-R2 (MT7623), MikroTik RouterBoard M11G (MT7621). [1]: https://patchwork.kernel.org/project/netdevbpf/list/?series=662108&state=* [2]: https://patchwork.kernel.org/project/netdevbpf/list/?series=675368&state=* (the first part of the series adding wed nodes to mt7986a.dtsi was applied to the copy of mt7986a.dtsi in our tree) [3]: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=5e69163d3b9931098922b3fc2f8e786af8c1f37e Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7621-dts: change phy-mode of gmac1 to rgmiiArınç ÜNAL2022-09-181-1/+1
| | | | | | | Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-29 05:31:35 +0000