aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for Netgear R6350NOGUCHI Hiroshi2018-12-165-2/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear R6350 is a wireless router, aka Netgear AC1750. Specification: - SoC: Mediatek MT7621AT (2 CPU cores, 4 threads) - RAM: 128MiB (Nanya NT5CC64M16GP-DI) - ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI) - Wireless: for 11b/g/n (upto 300Mbps): MT7603 for 11a/ac (upto 1450Mbps) : MT7615, is not avaliable now - Ethernet LAN speed: up to 1000Mbps - Ethernet LAN ports: 4 - Ethernet WAN speed: up to 1000Mbps - Ethernet WAN ports: 1 - USB ports: 1 (USB 2.0) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 2 - serial ports: unknown Installation through telnet: - Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port on the router. - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug (login if required, default: admin password) - You will see "Debug Enabled!" - Telnet 192.168.1.1 and login with "root" - ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for example. - cd /mnt/shares/myUdisk - mtd_write write rootfs.bin Rootfs - mtd_write write kernel.bin Kernel - reboot recovery when bricked: nmrpflash can be used to recover to the netgear firmware if a broken image was flashed. The SC_PART_MAP partition suggests that an on flash partition table exists. After implementing a partition parser/builder for the sercom partition format, the definitions don't match the flash layout used by the stock firmware. It either means the partition format has not yet been completely understood or it isn't used by the stock firmware. For now, use fixed partitions instead. Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [apply latest ramips changes and document the on flash partition map issues] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb packagesMathias Kresin2018-12-151-4/+16
| | | | | | | | | Add the usb drivers for all boards with enabled ochi/ehci node in the dts file. Fixes: FS#1987 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: remove unnecessary usb packagesMathias Kresin2018-12-151-3/+3
| | | | | | These are either installed as dependency or not required at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb ohci driverMathias Kresin2018-12-151-6/+6
| | | | | | | Add the USB 1.1 driver for all boards not having a fixed USB 2.0 device attached to the USB bus. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: several fixes for HC5x61Deng Qingfang2018-12-156-25/+43
| | | | | | | | | | | | | | | | | | | | | - Mark other partitions as read-only for HC5x61 - Only enable USB and PCIe for HC5761/HC5861 HC5661 doesn't have a USB port, and there is nothing attached to its PCIe. - Fix HC5761 switch ports HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports. - Fix HC5861 5GHz radio HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN. - Fix HC5761/HC5861 WiFi LEDs After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1. - Fix HC5x61 image size It should be 15872k (0xf80000) Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: disable CONFIG_MTD_SPLIT_FIRMWARERafał Miłecki2018-12-131-1/+0
| | | | | | | It's no longer needed as all mt7621 devices use DT binding (supported by upstream mtd code) for specifying "firmware" part format explicitly. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7621: specify "firmware" partition format for remaining devicesRafał Miłecki2018-12-134-0/+4
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: drop old image validation codeMathias Kresin2018-12-121-329/+1
| | | | | | | Due to the enforced image metadata we ensure that the correct image is uploaded. Checks based on a magic arn't required any more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: enforce image metadata verificationMathias Kresin2018-12-121-0/+1
| | | | | | | Now that we got rid of all legacy images, we can enforce image metadata verification. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3Mathias Kresin2018-12-127-448/+0
| | | | | | | | | | | | Beside one exception, no one took care of these two remaining boards still using the legacy image build code during the last two years. Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken. The Sitecom WL-341 v3 image build code looks pretty hackish and broken. It's questionable if the legacy image works as all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use new image build code for D-Link DCS-930 familyMathias Kresin2018-12-122-33/+16
| | | | | | | | | | | | Drop the factory images and the firmware tool to create them. They don't work any more, since the factory image has an uImage header covering the whole kernel + rootfs. This way the uImage splitter will not be able to find the rootfs and the kernel will panic later on. The factory images were most likely added at a time the board had distinct partitions for kernel and rootfs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.87Koen Vandeputte2018-12-101-29/+0
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0008-MIPS-ralink-Fix-mt7620-nd_sd-pinmux.patch Compile-tested: cns3xxx, imx6 Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.86Koen Vandeputte2018-12-103-11/+4
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: fix firmware compatible string for dir860l-b1Russell Senior2018-12-081-1/+1
| | | | | | | | In commit d70ec3008d4cd0540a9f6c88fb7e786107f1679a, a firmware compatible string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately, this was the wrong string. It needs "seama" instead. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ramips: fix dtc compiler warningsMathias Kresin2018-12-0611-38/+38
| | | | | | | | | | | | | | | | | The latest dtc compiler considers nodes named i2c or spi as the respective bus: /pinctrl/i2c: incorrect #address-cells for I2C bus /pinctrl/spi: incorrect #address-cells for SPI bus Rename the node to fix the false positives. Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get rid of the following warning: SPI bus unit address format error, expected "n" Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt76x8: select only the matching mt76 driverChen Minqiang2018-12-062-3/+9
| | | | | | | | | | | | | | | | | | | | | Select the matching mt76 driver for the PCI wireless of the following devices: - HiWiFi HC5861B - Mercury MAC1200R v2.0 - Netgear AC1200 R6120 - Buffalo WCR-1166DS - ZyXEL Keenetic Extra II - Wavlink WL-WN575A3 Because every device has selected the corresponding mt76 driver, we can include kmod-mt7603 instead of the mt76 metapackage, which used for the wireless of the mt7628 and mt7688 WiSoC. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> [select kmod-mt7603 as target default package, add wireless driver for WL-WN575A3] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: disable sdhc for HC5661AChuanhong Guo2018-12-062-5/+0
| | | | | | | | | | | | | Currently OpenWrt doesn't support switching MT7628 into AP mode (which is done by writing some undocumented registers in MTK SDK) Without doing so, enabling SD breaks 4 FE ports and the SD controller doesn't work since SD pins aren't configured correctly. Disable SDHC on HC5661A to recover the 4 FE ports. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [drop the sdhci node completely] Signed-off-by: Mathias Kresin <dev@kresin.me>
* apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic ↵Petr Štetiar2018-12-061-45/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | diag.sh I wanted to add status LEDs support to my imx6 based board and have found out, that I could use diag.sh script found in ramips platform, which seems to be also shared in a few other platforms: 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh And @chunkeey suggested to me, that I can also add lantiq, ipq806x and apm821xx to the list of platforms which could share this generic diag.sh. I've extended the base diag.sh in a way, that if it detects any of the DTS LED aliases, then it would use the generic DTS set_led_state code. The code in platform's diag.sh has moved to base-files package in this commit: base-files: diag.sh: Make it more generic towards DTS so it could be reused Signed-off-by: Petr Štetiar <ynezz@true.cz> Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
* ramips: fix Netgear EX3700/EX3800 wireless driver selectionMathias Kresin2018-12-041-1/+1
| | | | | | Fix the typo to select kmod-mt76x2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A1Pawel Dembicki2018-12-036-0/+215
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: select only the matching mt76 driverChen Minqiang2018-12-032-25/+28
| | | | | | | | | | | | | Because every device has selected the corresponding mt76 driver, we can now disable the mt76 metapackage by default to make sure that other devices (those don't need mt76) avoid selecting unwanted packages. We can find the hardware specifies and determine the dependencies on these sites: https://wikidevi.com/wiki/ https://openwrt.org/toh/hwdata/ Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: drop mt76 driver for boards without mt76 wirelessChen Minqiang2018-12-031-4/+4
| | | | | | | These boards don't have a mt76 wireless at all and don't need any of the mt76 family drivers. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: disable PCIe if nothing is attachedMathias Kresin2018-12-034-16/+0
| | | | | | | | All boards neither expose the PCIe as Mini-PCIe nor have anything attached to the PCIe Bus. Disable PCIe for those by dropping the node from the dts files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add missing pci wifi nodes to dts filesChen Minqiang2018-12-033-0/+24
| | | | | | | | | These devices has pci wifi but not defined in dts: HC5761 HC5861 TINY-AC Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: merge relocate compile into build recipeMathias Kresin2018-11-302-10/+5
| | | | | | | Compile the loader if the relocate-kernel image recipe is used and get rid of the legacy build code to do so. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: specify "firmware" partition format in JBOOT devicesPawel Dembicki2018-11-305-3/+8
| | | | | | | | | | | | | Specify firmware partition format by compatible string. List of devices: -DWR-116-A1 -DWR-118-A2 -DWR-512-B -DWR-921-C1 -LR-25G001 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for MTC Wireless Router WR1201Valentín Kivachuk2018-11-305-0/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTC Wireless Router WR1201 is the OEM name of the board. It is also sold rebranded as STRONG Dual Band Gigabit Router 1200. Specification: - SoC: MediaTek MT7621A (880 MHz) - Flash: 16 MiB - RAM: 128 MiB - Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN) - Ethernet speed: 10/100/1000 - Ethernet ports: 4+1 - 1x USB 3.0 - 1x microSD reader - Serial baud rate of Bootloader and factory firmware: 57600 The OEM webinterface writes only as much bytes as listed in the uImage header field to the flash. Also, the OEM webinterface evaluates the name field of uImage header before flashing (the string "WR1201_8_128") To flash via webinterface, is mandatory to use first initramfs.bin and after (from the OpenWrt) the sysupgrade.bin Some notes: - Some microSD will not work: mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: card claims to support voltages below defined range mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
* ramips: specify "firmware" partition formatINAGAKI Hiroshi2018-11-29246-0/+246
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specify firmware partition format by compatible string. formats in ramips: - denx,uimage - tplink,firmware - seama It's unlikely but the firmware splitting might not work any longer for the following boards, due to a custom header: - EX2700: two uImage headers - BR-6478AC-V2: edimax-header - 3G-6200N: edimax-header - 3G-6200NL: edimax-header - BR-6475ND: edimax-header - TEW-638APB-V2: umedia-header - RT-N56U: mkrtn56uimg But it rather looks like the uImage splitter is fine with the extra header. The following dts are not touched, due to lack of a compatible string in the matching firmware splitter submodule: - CONFIG_MTD_SPLIT_JIMAGE_FW DWR-116-A1.dts DWR-118-A2.dts DWR-512-B.dts DWR-921-C1.dts LR-25G001.dts - CONFIG_MTD_SPLIT_TRX_FW WCR-1166DS.dts WSR-1166.dts - CONFIG_MTD_SPLIT_MINOR_FW RBM11G.dts RBM33G.dts - CONFIG_MTD_SPLIT_LZMA_FW AR670W.dts - CONFIG_MTD_SPLIT_WRGG_FW DAP-1522-A1.dts Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: unifiy sysupgrade file extensionsMathias Kresin2018-11-292-8/+7
| | | | | | | Use .bin as file extension where possible. The user doesn't need to that sysupgrade images for NAND boards are tarballs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove duplicate image build variablesMathias Kresin2018-11-291-4/+1
| | | | | | | Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: bdcom-wap2100: Change DTS license to GPL-2.0-or-later OR MITPetr Štetiar2018-11-291-0/+1
| | | | | | | | Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix MTD EEPROM offset for TL-WR840N v5Felix Fietkau2018-11-291-1/+1
| | | | | | | The previous offset was invalid and pointed to the end of the partition, which was causing issues with mt76 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: bdcom-wap2100: Enable mt7610e 5GHz radioPetr Štetiar2018-11-282-1/+13
| | | | | | | | | | | | The 5GHz radio of this device uses an mt7610e PCI-E chip, which has been recently started to be supported. mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 mt76x0e 0000:01:00.0: ASIC revision: 76100002 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: bdcom-wap2100: Set firmware partition format to denx,uimagePetr Štetiar2018-11-281-0/+1
| | | | | | | | | | | Specify firmware partition format to denx,uimage in compatible DTS property. 2 uimage-fw partitions found on MTD device firmware Creating 2 MTD partitions on "firmware": 0x000000000000-0x00000017f72b : "kernel" 0x00000017f72b-0x000000f70000 : "rootfs" Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: bdcom-wap2100: Fix boot failure by adding partitions compatible propertyPetr Štetiar2018-11-281-0/+1
| | | | | | | | | | | | | | Flash partitions were moved under partition table node, but addition of compatible property was omitted which lead to following boot failure: VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 Please append a correct "root=" boot option; here are the available partitions: 1f00 16384 mtdblock0 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support) Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix switch port order for HuaWei HG255DDavid Yang2018-11-281-1/+1
| | | | | | The order of port marks and LEDs is reversed according to the board. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: mt7620: add DIR-810L's mt7610e 5 GHz radioRoger Pueyo Centelles2018-11-282-1/+10
| | | | | | | | | | The 5 GHz radio of this device uses an mt7610e pci-e chip, which has been recently added support. Tested on the actual device as AP and client, TCP throughput ~90 Mbps U/D. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for UniElec U7621-06-512M-64M variantNishant Sharma2018-11-284-0/+102
| | | | | | | | | | | | | | | | | | | | | | Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash. Additional specs are below: CPU: MT7621 (880Mhz) Bootloader: Ralink U-Boot Flash: 64MB - U-Boot identifies as Macronix MX66L51235F - kernel identifies as MX66L51235l (65536 Kbytes) RAM: 512MB Rest of the details as per commit 46ab81e405d2 ("ramips add support for UniElec U7621-06") Signed-off-by: Nishant Sharma <nishant@unmukti.in> [use generic board detection, add firmware partition compatible, extend firmware partition to use all of the remaining flash space, add a maximum image size matching the firmware partition size] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use generic board detection for Unielec u7621-06Mathias Kresin2018-11-284-13/+11
| | | | | | | | Use the generic board detection for the board instead of the target specific one. Mark the sysupgrade image compatible with the former used userspace boardname to allow an upgrade from earlier versions. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Wavlink WL-WN570HA1Thomas Vincent-Cross2018-11-285-0/+154
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN570HA1, a dual-band PoE wireless router with the following specifications: - CPU: MediaTek MT7688AN 580MHz - Flash: 8MB - RAM: 64MB - Ethernet: 1x 10/100Mbps - 2.4 GHz: 802.11b/g/n SoC, 1T1R, 27 dBm - 5 GHz: 802.11a/n/ac MT7610E, 1T1R, 25 dBm - Antennas: 2x external (1 per radio), detachable - LEDs: 3 programmable + Wi-Fi, WAN/LAN, Power - Buttons: Reset Flashing instructions: Factory U-boot launches a TFTP client if reset button is pressed during power-on. Rename the sysupgrade file and configure TFTP as follows: - Client (WL-WN570HA1) IP: 192.168.10.101 - Server IP: 192.168.10.100 - Filename: firmware.bin Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au> [use generic board detection, add firmware partition compatible] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix alphabetic ordering of skylab skw92aRussell Senior2018-11-271-1/+1
| | | | | | Fix the alphabetic ordering of skylab skw92a in ramips_setup_interfaces. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ramips: fix RavPower WD03 SoC dtsi includeMatthias Badaire2018-11-271-1/+1
| | | | | | | | | The RavPower WD03 is a mt7620n based baord. With the change applied, I2C should work now with the RavPower WD03. Signed-off-by: Matthias Badaire <mbadaire@gmail.com> [reworded commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix GB-PC1/PC2 build errorMathias Kresin2018-11-262-10/+0
| | | | | | | | | | With ed25e3ac02d9 ("ramips: fix some clocks in mt7621.dtsi") the cpuclock node was dropped from the mt7621.dtsi without removing the references to this node from the GB-PC1/PC2 dts files. Remove them now, to fix the build error. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Lava LR-25G001 invalid led namesMathias Kresin2018-11-261-6/+4
| | | | | | | | | | It has to be <board>:<colour>:<function> and is expected exactly this way by the userspace scripts. While at it, fix some whitespace issues in the dts file and rename the flash node as required upstream. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rt2880: fix pci cells definitionMathias Kresin2018-11-261-2/+2
| | | | | | | Set the correct number of cells to fix "property has invalid length" dtc compiler warnings. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: improve BDCOM WAP2100-SK supportMathias Kresin2018-11-266-46/+47
| | | | | | | | | | | | | | | | | | | | | Use the generic board detection instead of the target specific one as all recent additions are doing. Setup the USB led via devicetree (a58535771f11) and include the required driver by default. Merge the led userspace setting with an existing identical case. Use the wps led for boot status indication. Move the partitions into a partition table node (6031ab345df8) and drop needless labels. Drop misplaced cells properties (53624c1702e6). Cleanup the pinmux and only switch pins to gpio functions which a referenced as gpio in the dts. Match the maximum image size with the size of the firmware partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add Sanlinking Technologies D240 pinmux quirkMathias Kresin2018-11-261-0/+16
| | | | | | | | | | | | | | The sd function of the nd_sd group configures two of the groups pins as gpios. The pins are used as PCIe reset/power. Due to the driver load order, the pins are configured way to late if triggered by the sd-card driver. To not introduce another kind of driver load order dependency and configure the pins as early as possible, means during pinmux driver load. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ralink: fix mt7620 nd_sd pinmuxMathias Kresin2018-11-261-0/+29
| | | | | | | | | In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are configured as GPIOs. If they are blocked by the sd function, they can't be used as GPIOs. Reported-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: revert fix rt3883 pci pinmuxMathias Kresin2018-11-261-1/+1
| | | | | | | | | | | | | | | This reverts commit dcdc6d9dadf2f97253f7891dacdd5b581d7914b4. Even if described this way in the datasheet, it causes a bootloop on a RT-N56U (v1): of-flash 1c000000.nor-flash: do_map_probe() failed for type cfi_probe of-flash 1c000000.nor-flash: do_map_probe() failed VFS: Cannot open root device “(null)” or unknown-block(0,0): error -6 Fixes: FS#1930 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: improve Skylab SKW92A supportMathias Kresin2018-11-266-21/+15
| | | | | | | | | | | | | | | | Use the generic board detection instead of the target specific one as all recent additions are doing. Add the wireless led according the gpio number from the datasheet. Rename the board part of the leds to match the name used for the compatible string. Finally, do not hijack the wps led for boot status indication longer than necessary. Merge userspace config into existing cases. Include the manufacture Name in the dts model string. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-26 20:11:58 +0000