aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-214-3/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add #pwm-cells property to MT76x8 dtsMicke Prag2019-03-181-0/+1
| | | | | | | To be able to configure pwms the pwm driver needs to know the number off cells in the "pwms" property. For this platform this is 2. Signed-off-by: Micke Prag <micke.prag@telldus.se>
* kernel: bump 4.14 to 4.14.106Koen Vandeputte2019-03-181-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: HC5861 drop unused gpio group define in dtsChen Minqiang2019-03-131-7/+0
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for Xiaomi Mi Router 3 ProOzgur Can Leonard2019-03-135-2/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: CPU: MediaTek MT7621AT (2x880MHz) RAM: 512MB DDR3 FLASH: 256MB NAND WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!) WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!) USB: 1x 3.0 ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000 LED: Power/Status BTN: RESET UART: 115200 8n1 Partition layout and boot: Stock Xiaomi firmware has the MTD split into (among others) - kernel0 (@0x200000) - kernel1 (@0x600000) - rootfs0 - rootfs1 - overlay (ubi) Xiaomi uboot expects to find kernels at 0x200000 & 0x600000 referred to as system 1 & system 2 respectively. a kernel is considered suitable for handing control over if its linux magic number exists & uImage CRC are correct. If either of those conditions fail, a matching sys'n'_fail flag is set in uboot env & a restart performed in the hope that the alternate kernel is okay. If neither kernel checksums ok and both are marked failed, system 2 is booted anyway. Note uboot's tftp flash install writes the transferred image to both kernel partitions. Installation: Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in kernel0 for ease of recovery, and install OpenWRT into kernel1 and after. The installation file for OpenWRT is a *squashfs-factory.bin file that contains the kernel and a ubi partition. This is flashed as follows: nvram set flag_try_sys1_failed=1 nvram set flag_try_sys2_failed=0 nvram commit dd if=factory.bin bs=1M count=4 | mtd write - kernel1 dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0 reboot Reverting to stock: The part of stock firmware we've kept in kernel0 allows us to run stock recovery, which will re-flash stock firmware from a *.bin file on a USB. For this we do the following: fw_setenv flag_try_sys1_failed 0 fw_setenv flag_try_sys2_failed 1 reboot After reboot the LED status light will blink red, at which point pressing the 'reset' button will cause stock firmware to be installed from USB. Issues: OpenWRT currently does not have support for the MT7615 wifi chips. There is ongoing work to add mt7615 support to the open source mt76 driver. Until that support is in place, there are closed-source kernel modules that can be used. See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170 Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [02_network remaps, Added link to notes]
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-114-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: rework network settings for HC5861Chen Minqiang2019-03-062-18/+14
| | | | | | | dts: disable port4 and leave it ephy mode because it connect to nothing switch port5 connected to GE port we use it as wan port Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: export chip version and pkgDaniel Golle2019-03-061-0/+19
| | | | | | | | | | | Similar to the (currently unused) mt7620_get_eco() function, introduce mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to probe for the type of WiSoC. This is ugly and probably unacceptable for upstream, however, it should help to evaluate which of those hacks are actually really needed, enumerate the possible values and label them in a more meaningful way than currently done in the vendor driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Belkin F9K1109v1Kip Porterfield2019-03-025-0/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz - RAM: 64Mb - Flash: 8MB (SPI-NOR) - Ethernet: 10/100/1000 Mbps - WLAN Wireless 1: SoC-integrated : 2.4/5 GHz Wireless 2: 2.4 GHz RT3092L - LED: 2x USB, WAN, LAN - Key: WPS, reset - Serial: 4-pin header, (57600,8,N,1), 3.3V TTL, GND, RX, TX, V - J12 marking on board - USB ports: 2 x USB 2.0 Flashing instructions: Option 1 (from bootloader web) - Hold reset button on the back of router when plugging in power (for at-least 10 seconds after plugged in) - Connect to a Lan port - Set computer IP to 10.10.10.3 - Go to http://10.10.10.123 in a web browser - Click the Browse... Button and select the *squashfs.sysupgrade.bin file then click APPLY Option 2 (from the stock admin web) - Go to firmware upgrade - Upload the **factory** image *initramfs.bin first - Boot into openwrt - From Luci web in openwrt upload the *squashfs.sysupgrade.bin Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added v1 to the compatible identifier, added pciid for the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi to prepare for a possible F9K1103 patch]
* ramips: add TP-Link TL-WR802N-v4 supportMarcel Jost2019-02-283-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N-v4. https://openwrt.org/toh/tp-link/tl-wr802n Specification: - MT7628N (580 MHz) - 64 MB RAM - 8 MB FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet - 1x LED Flash instruction: The only way to flash the image in TL-WR802N v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 10 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Marcel Jost <majo@icutech.ch>
* ramips: use generic board detection for Wavlink WL-WN575A3Thomas Vincent-Cross2019-02-284-17/+15
| | | | | | Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices. Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: various Wavlink WL-WN575A3 fixesThomas Vincent-Cross2019-02-281-4/+3
| | | | | | | | | * assign pinmux groups to gpio function for LEDs/buttons * rename flash node to be more generic in line with other device nodes * remove useless/incorrect eeprom property from wmac node * correct base mac address for embedded switch Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: change status LED for Buffalo WHR-G300NINAGAKI Hiroshi2019-02-141-6/+5
| | | | | | | | | | | Buffalo WHR-G300N has a LED for power status indication, but it is not connected to the GPIO and cannot be controlled by the kernel. So, WHR-G300N uses "ROUTER" LED as the system status LED instead. This commit changes it to use "DIAG" LED insted of "ROUTER" like WHR-G301N in ath79 target. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: various Netgear R6120 fixesDavid Bauer2019-02-143-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls the WAN LED. Renames the LED accordingly in the device-tree. Removes the 5GHz WLAN LED trigger. Adds the correct WAN port LED trigger. ---- Currently, the MAC address for the Netgear R6120 is read from the NVRAM partition. The offset for the MAC address however is not consistent across devices or firmware versions. Switch to using the factory partition like all other Netgear devices do. ---- The LAN ports of the R6120 are labled in reverse on the casing. Adjust LuCI switchport numbering accordingly. ---- The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset is bigger than the partition itself). Fixes poor performance on 2.4 and 5 GHz. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-144-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-143-3/+3
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: drop m25p,chunked-io from dtsChuanhong Guo2019-02-0562-62/+0
| | | | | | | | This option was a spi nor hack which is dropped in commit bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead") Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
* ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVBDeng Qingfang2019-02-052-0/+9
| | | | | | This enables MT7610E of the EVB Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add kmod-mt76x2 to WeVo 11AC NASJu Se Hoon2019-02-051-1/+1
| | | | | | | | The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB. Signed-off-by: Ju Se Hoon <joosahoon@gmail.com> [renamed author from Albis-dev to real name, editted commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: dts: Unify naming of gpio-led nodesPetr Štetiar2019-02-05243-243/+243
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* ramips: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-02-05241-241/+241
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* kernel: bump 4.14 to 4.14.97Koen Vandeputte2019-02-011-1/+1
| | | | | | | | | | | | Refreshed all patches. Adapted patches: - 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: rb750gr3: License DTS as GPL-2.0-or-later OR MITAnton Arapov2019-02-011-0/+1
| | | | | | | | | | | | | Adding license in order to fully satisfy dts checklist: - https://openwrt.org/submitting-patches#dts_checklist Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Thibaut <hacks@slashdirt.org> Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Chuanhong Guo <gch981213@gmail.com> Acked-by: Andrew Yong <me@ndoo.sg> Acked-by: Alex Maclean <monkeh@monkeh.net>
* ramips: fix D-Link DIR-615 H1 switch port mappingMirko Parthey2019-01-301-0/+1
| | | | | | | Reuse a device-specific switch port mapping which also applies to the D-Link DIR-615 H1. Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
* ramips: move wifi related interrupts off the main core on SMP systemsFelix Fietkau2019-01-291-0/+31
| | | | | | Improves LAN<->WLAN bridging/routing performance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.14 to 4.14.96Koen Vandeputte2019-01-282-2/+2
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed patches: - 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: Fix kmod-regmap splitHauke Mehrtens2019-01-271-1/+1
| | | | | | | | Two regmap dependencies were wrong, this patch fixes them. This was detected by the build bots. Fixes: fd5c16870169 ("kernel: Build: Split kmod-regmap") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Build: Split kmod-regmapHauke Mehrtens2019-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | This reduces the needed modifications to the mainline Linux kernel and also makes the regmap package work with an out of tree kernel which does not have these modifications. The regmap-core is only added when it is really build as a module. The regmap-core is normally bool so it cannot be built as a module in an unmodified kernel. When it is selected by on other kernel module it will always be selected as build in and it also does not show up in $(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module. When it is not in $(LINUX_DIR)/modules.builtin the build system expects it to be built as a .ko file. Just check if the module is really there and only add it in that case. This splits the regmap package into multiple packages, one for each bus type. This way only the bus maps which are really needed have to be added. This also splits the I2C, SPI and MMIO regmap into separate packages to not require all these subsystems to build them, on an unmodified upstream kernel this also causes problems in some situations. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
* ramips: rt3883: drop jimage supportMathias Kresin2019-01-261-1/+0
| | | | | | The splitter isn't required by any of the boards in the subtarget. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: disable CONFIG_MTD_SPLIT_FIRMWAREMathias Kresin2019-01-265-5/+0
| | | | | | | It's no longer needed as all mt7621 devices use DT binding (supported by upstream mtd code) for specifying "firmware" part format explicitly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: specify "firmware" partition format for remaining devicesRafał Miłecki2019-01-263-0/+3
| | | | | | | | | It results in calling the right MTD parser directly instead of trying them one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> [use the lzma splitter for the AR670W] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Archer C50 v4David Bauer2019-01-266-1/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link Archer C50 v4. It uses the same hardware as the v3 variant, sharing the same FCC-ID. CPU: MediaTek MT7628 (580MHz) RAM: 64M DDR2 FLASH: 8M SPI WiFi: 2.4GHz 2x2 MT7628 b/g/n integrated WiFI: 5GHz 2x2 MT7612 a/n/ac ETH: 1x WAN 4x LAN LED: Power, WiFi2, WiFi5, LAN, WAN, WPS BTN: WPS/WiFi, RESET UART: Near ETH ports, 115200 8n1, TP-Link pinout Create Factory image -------------------- As all installation methods require a U-Boot to be integrated into the Image (and we do not ship one with the image) we are not able to create an image in the OpenWRT build-process. Download a TP-Link image from their Wesite and a OpenWRT sysupgrade image for the device and build yourself a factory image like following: TP-Link image: tpl.bin OpenWRT sysupgrade image: owrt.bin > dd if=tpl.bin of=boot.bin bs=131584 count=1 > cat owrt.bin >> boot.bin Installing via Web-UI --------------------- Upload the boot.bin via TP-Links firmware upgrade tool in the web-interface. Installing via Recovery ----------------------- Activate Web-Recovery by beginning the upgrade Process with a Firmware-Image from TP-Link. After starting the Firmware Upgrade, wait ~3 seconds (When update status is switching to 0%), then disconnect the power supply from the device. Upgrade flag (which activates Web-Recovery) is written before the OS-image is touched and removed after write is succesfull, so this procedure should be safe. Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1. When active, all LEDs but the WPS LED are off. Remeber to assign yourself a static IP-address as DHCP is not active in this mode. The boot.bin can now be uploaded and flashed using the web-recovery. Installing via TFTP ------------------- Prepare an image like following (Filenames from factory image steps apply here) > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1 > dd if=tpl.bin of=tmp.bin bs=131584 count=1 > dd if=tmp.bin of=boot.bin bs=512 skip=1 > cat boot.bin >> tp_recovery.bin > cat owrt.bin >> tp_recovery.bin Place tp_recovery.bin in root directory of TFTP server and listen on 192.168.0.66/24. Connect router LAN ports with your computer and power up the router while pressing the reset button. The router will download the image via tftp and after ~1 Minute reboot into OpenWRT. U-Boot CLI ---------- U-Boot CLI can be activated by holding down '4' on bootup. Dual U-Boot ----------- This is the first TP-Link MediaTek device to feature a split-uboot design. The first (factory-uboot) provides recovery via TFTP and HTTP, jumping straight into the second (firmware-uboot) if no recovery needs to be performed. The firmware-uboot unpacks and executed the kernel. Web-Recovery ------------ TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 / TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition before beginning to write and removes it afterwards. If the router boots with this flag set, bootloader will automatically start Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT factory image can be written. By doing the same while performing sysupgrade, we can take advantage of the Web-recovery in OpenWRT. It is important to note that Web-Recovery is only based on this flag. It can't detect e.g. a crashing kernel or other means. Once activated it won't boot the OS before a recovery action (either via TFTP or HTTP) is performed. This recovery-mode is indicated by an illuminated WPS-LED on boot. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix support for MX25L25635F flashDeng Qingfang2019-01-264-6/+80
| | | | | | | | | | | | | | | | | | | Patch picked from commit 82618062cf7e This enables 4B opcodes for MX25L25635F, to fix the reboot crash issue (FS#1120) At least 3 devices are using this flash - GeHua GHL-R-001 - Youku YK1 - Newifi D1 Now the MX25L25635F can be correctly detected without breaking MX25L25635E [ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes) [ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0 [ 3.068748] Creating 4 MTD partitions on "spi0.0": Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
* ramips: adjust Netgear R6120 model nameDavid Bauer2019-01-262-2/+2
| | | | | | | Adjust the model string and device title to match other Netgear routers in the ramips target. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix two-way hash and auto ageout on MT7621HsiuWen Yen2019-01-231-17/+18
| | | | | | | | | | | | | | | | | | | | | | | | Current code directly writes the FOE entry to hash_val+1 position when hash collision occurs. However, it is found that this behavior will cause the cache and the hardware FOE table to be inconsistent. For example, there are three flows, and their hashed values are all equal to 100. The first flow is written to the position of 100. The second flow is written to the position of 100+1. Then, the logic of the current code will also write the third flow to 100+1. At this time, the cache has flow 1 and 2; and the hardware FOE table has flow 1 and 3, where these two parts store different contents. So it is necessary to check whether the hash_val+1 is also occupied before writing. If hash_val+1 is also occupied, we won’t bind th third flow to the FOE table. Addition to that, we also cancel the processing of foe_entry removal because the hardware has auto age-out ability. The hardware will periodically iterate through the FOE table to find out the time-out entry and set it as INVALID. Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
* ramips: fix firmware splitter for edimax based boardsMathias Kresin2019-01-194-4/+4
| | | | | | Use the correct splitter for board with the edimax header. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mksercommfw: overhaul image creationMathias Kresin2019-01-151-9/+14
| | | | | | | | | | | | | | | | | | | | Move the zip compression into a build recipe. Pad the image using the existing build recipes as well to remove duplicate functionality Change the code to append header and footer in two steps. Allow to use a fixed filename as the netgear update image does. Use a fixed timestamp within the zip archive to make the images reproducible. Due to the changes we are now compatible to the gnu89 c standard used by default on the buildbots and we don't need to force a more recent standard anymore. Beside all changes, the footer still looks wrong in compare to the netgear update image. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.91Koen Vandeputte2019-01-074-9/+9
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: whitespace cleanup inside hnat driverJohn Crispin2019-01-071-6/+8
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add two-way hashing scheme for MT7621HsiuWen Yen2019-01-071-0/+11
| | | | | | | | | | Sometimes the tuples might be hashed to the same FOE entry. When this hash collision problem occurs, some of the connections will not be bound and consequently the CPU idle rate cannot reach 100%. Therefore, two-way hashing is adopted to alleviate this problem. Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
* ramips: cleanup the RB750Gr3 supportAnton Arapov2019-01-053-24/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | Always enable the pwr led and use the usr led for boot status indication. Rename nodes in the dts, to match what is recommend in the devicetree specification. Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io which isn't required on mt7621. Use the BTN_0 keycode for the mode button. This board doesn't have any wireless. Use a more descriptive label for the reset button and the GPIO enabling the usb vcc supply. Use the beeper kernel module for the buzzer. Fix the pinmux to switch only pins used as GPIOs to the GPIO function. Add support for the PoE enable GPIO to the userspace. The PoE power status can be read via GPIO7. Since OpenWrt doesn't have support for reading inputs from userspace, prepare only the pinmux for the GPIO. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add RB750Gr3 native supportAnton Arapov2019-01-055-31/+48
| | | | | | | | | | | | | | | | | This patch adds support of MikroTik RouterBOARD 750Gr3, without the need to reflashing the bootloader. Installation through RouterBoot follows the usual MikroTik method https://openwrt.org/toh/mikrotik/common Since the image isn't compatible with RouterBOARD 750Gr3 installations which have replaced the bootloader, the former used userspace boardname is not added to the SUPPORTED_DEVICES, to prevent a brick while trying to upgrade to the image with native support. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix spaces vs. tabsPaul Wassi2018-12-311-1/+1
| | | | | | Fix spaces vs. tabs issues in ath79 and ramips. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* build: move seama commands to image-commands.mkMathias Kresin2018-12-301-12/+0
| | | | | | Move it to image-commands.mk to get rid of duplicate recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: consolidate seama image build codeMathias Kresin2018-12-305-57/+31
| | | | | | | | Create a common template which has the required image build code defined. Add some new variables to pass individual parts to the seama recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for GeHua GHL-R-001Deng Qingfang2018-12-294-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | Specs SoC: MT7621AT RAM: 512MiB Flash: 32MiB MX25L25635F SPI NOR 2.4G: MT7603EN 5G: MT7612EN Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs USB 3.0 LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet. The last two ones are controlled by GPIO UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board. UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip. The stock u-boot uses UARTLITE1 by default. Baud rate is 57600 Flash instruction 1. telnet 192.168.9.1 2317, username is "root" and password is "admin" One can alternatively use UART to log in 2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router One can alternatively download the firmware via wget through Internet 3. mtd write /path/to/openwrt.bin firmware 4. reboot Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix MT7621 dtsiDeng Qingfang2018-12-291-2/+38
| | | | | | | Fix SysTick reg Add uartlite2 and uartlite3 nodes Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for DLINK DWR-922-E2Simon Quigley2018-12-295-1/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not sure if supported, I didn't try), wireless router with QMI LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-922-e2:green:signalstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Works correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui, or via recovery interface: How to recover/revert to OEM firmware: 1.) Push and hold the reset button and turn on the power. Wait until all LEDs start rapidly blinking (~10sec.) 2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set one manually 3.) Upload original factory image via JBOOT http interface at IP 192.168.123.254 4.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. 5.) You can optionally telnet to 192.168.123.254 before or during the upload and it will report the flashing status, memory address etc. 6.) Once web UI and/or telnet says "Success", power cycle the router, or type "reboot" into the telnet session. Signed-off-by: Simon Quigley <squigley@squigley.net> [squashed commits, word wrap commit message, rename signal strenght led name to match what is used for the DWR-921-C1 since they share the led configuration, add label referenced in the aliases node] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526Andreas Ziegler2018-12-291-0/+4
| | | | | | This fixes the 5GHz WiFi LED which was previously not working. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ramips: add support for CreativeBox v1Weijie Gao2018-12-284-0/+187
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 512MB DDR3 Flash: 32MB SPI-NOR WiFi 2.4GHz: MT7603 @ PCIe0 WiFi 5.8GHz: MT7612 @ PCIe1 SATA: ASM1061 @ PCIe2 Interfaces: GBE RJ45 x5 USB3.0 x1 eSATA (with USB2.0) x1 SATA x1 UART x1 I2C x1 JTAG x1 Flash instructions: Through factory bootloader or firmware web interface Signed-off-by: Weijie Gao <hackpascal@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 04:57:23 +0000