aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Fix VLAN limits for MT7621 GSWAntonis Kanouras2017-01-101-1/+5
| | | | | | | | | Without this patch swconfig will only allow setting up a total of 16 VLANs, with VLAN ID range of 0-15. Tested on ubnt-erx. Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
* kernel: remove ubifs xz decompression supportFelix Fietkau2017-01-091-1/+0
| | | | | | | It has been unused, and less useful than squashfs for cases where flash space usage matters. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump to 4.4.40Hauke Mehrtens2017-01-061-14/+0
| | | | | | | Refresh patches on all 4.4 supported platforms. Compile & run tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* build: use mkhash to replace various quirky md5sum/openssl callsFelix Fietkau2017-01-052-6/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: mtd: backport SPI_NOR_HAS_LOCKVictor Shyba2017-01-031-3/+3
| | | | | | | | | This flag was added to 4.9 with upstream commit 76a4707de5e18dc32d9cb4e990686140c5664a15. Signed-off-by: Victor Shyba <victor1984@riseup.net> [refresh and adjust platform patches, fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: MiWiFi Nano fixesL. D. Pinney2017-01-023-18/+31
| | | | | | | | | | | | | | | | Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix NixcoreX1 profilesRafał Miłecki2016-12-281-2/+2
| | | | | | | There was a typo in Makefile that prevented using these profiles. Fixes: a75ce960ac1 ("ramips: use different board names for variants") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: use new image build code for more devicesMathias Kresin2016-12-2420-413/+447
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use different board names for variantsMathias Kresin2016-12-2414-30/+49
| | | | | | | | | | | | Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: sort rt305x image file alphabeticalMathias Kresin2016-12-241-218/+155
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use D-Link DIR-600 B1 image for B2 versionMathias Kresin2016-12-246-121/+1
| | | | | | | Everything set for the B1 is identical to the values uses for the B2 version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix image validation errorsMathias Kresin2016-12-244-13/+15
| | | | | | | | | | | The name from the Device define will be used in the metadata. Due to typos/different spelling, this name might not match the one exported in /lib/ramips.sh. Fix all name mismatches which were found by checking if the name used in the metadata exists in /lib/ramips.sh. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use destinct 11AC NAS board nameMathias Kresin2016-12-246-30/+44
| | | | | | | | | | Use a distinct board name even if the board is near to identical to the WeVO W2914NS v2. To make sure that a 11AC NAS image can not be installed on a WeVO W2914NS v2, both board need to use different names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix tplink image building fix sysupgrade firmware on MR200Henryk Heisig2016-12-241-4/+5
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: enablemodem: move /lib/ramips.sh to start()Henryk Heisig2016-12-241-1/+2
| | | | | | Fix build error: /etc/init.d/enablemodem: line 2: /lib/ramips.sh: No such file or directory Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-228-1/+240
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-228-0/+277
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: adding registration for si3210Giuseppe Lippolis2016-12-201-0/+13
| | | | | | | | | | | | | | | The si3210 is a SLIC device providing a complete analog telephone interface and therefore frequently used in soho router. The si3210 have a native spi interface to be controlled by the CPU but currently there is no dedicated driver in lede. Adding a registration for this device in spidev allow to control the device in user space. This way of patching is also in line with the rationale of the spidev driver, see: http://marc.info/?t=148145791900001&r=1&w=2 The si3210 has been also added in the DWR-512 DT to properly describe the HW. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* kernel: bump to 4.4.39Kevin Darbyshire-Bryant2016-12-201-3/+3
| | | | | | | | Bump & refresh patches for all 4.4 targets. Compile & run tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ramips: WNDR3700v5 fix mtd partitions and radiosL. D. Pinney2016-12-201-6/+7
| | | | | | | Fix the mtd partition layout and enable both radios in the dts Tested-by Andrius Štikonas <andrius@stikonas.eu> Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* ramips: adding DWM-158 3g ModemGiuseppe Lippolis2016-12-141-0/+14
| | | | | | | | | This patch add the 3G modem DWM-158 to the usb-serial option driver. The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem supportet by lede. The patch has been submitted and merged in the upstream linux-next repository. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: Fix led init script for Lenovo Y1/Y1sBangLang Huang2016-12-041-3/+10
| | | | | | | This commit fix the led init script for Lenovo Y1 and Y1S due to the manual and dts file. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: prevent packet forwarding on mt7620 between switch ports during init ↵Felix Fietkau2016-12-042-5/+7
| | | | | | | | | | | | | | | | (FS#103) By default, forwarding between all ports is allowed on init. This is problematic in cases where some ports are supposed to be isolated from each other, most commonly LAN/WAN separation. REG_ESW_PORT_PCR(port) has a destination mask for a particular port, controlling what other ports it is allowed to send packets to. Instead of initializing all to 0xff (all ports), allow each physical port to send to the CPU port, and the CPU port to send to all other ports. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix LAN port order of WeVO W2914NS v2Yong-hyu, Ban2016-12-041-1/+4
| | | | Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
* ramips: fix PBR-D1 button definitionBangLang Huang2016-12-041-2/+2
| | | | | | | Due to the product specification, the button on PBR-D1 should be reset, not wps. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1Tobias Wolf2016-12-042-1/+10
| | | | | | This router uses an PCI attached NEC EHCI controller to support the single USB port. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288xTobias Wolf2016-12-044-5/+17
| | | | | | This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: improve F5D8235 V1 supportTobias Wolf2016-12-044-18/+78
| | | | | | | | | | | | | | | | | | | This fixes the partition name for the firmware splitter, the cfi address and adds the mtd-eeprom address for wmac. It adds additional LEDs and make use of them in diag.sh and 01_leds. Please note that the ":blue:wired" LED is used because the ":blue:router" behaviour is unpredictable for failsafe indication. The issue with the router LED is that you have two states only. "off" is steady on and "on" blinks. Therefore the wired LED is more suitable. Furthermore it reuses the correct switch configuration definition to reflect the device ports and numbering. Additionally fixes the issue that the default configuration is not applied as no port 6 exists on this device. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: fix sdhci support on mt7621John Crispin2016-12-012-24/+10
| | | | | | the IRQ level was wrong. refresh the patch while at it. Signed-off-by: John Crispin <john@phrozen.org>
* ramips: RB750Gr3: Add pwr LED and buzzer to DTSAndrew Yong2016-12-012-2/+13
| | | | | | | | | use pwr LED in diag.sh Expose unused pinmux pins as GPIOs export power LED and buzzer pins Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr Signed-off-by: Andrew Yong <me@ndoo.sg>
* treewide: fix button keys codes used in dtsMathias Kresin2016-11-277-7/+7
| | | | | | Use keycodes that matches the intended use case based on the label. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add size checks/append metadata where missingMathias Kresin2016-11-273-30/+22
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Airlink AR670W factory imageMathias Kresin2016-11-272-8/+7
| | | | | | | Move the mkwrgimg build step to the makefile. It will be required by other boards as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add missing chunked-io directive to W2914NSV2.dtsiYong-hyu, Ban2016-11-261-0/+1
| | | | | | | | | Fix bug that LEDE failed to boot with this message: WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214 mt7621_spi_transfer_one_message+0x28c/0x620() Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
* ramips: SamKnows SK-WB8 DTS cleanupAndrew Yong2016-11-261-11/+6
| | | | | | Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000). Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: remove kmod-ledtrig-usbdev from recently added devicesMathias Kresin2016-11-241-2/+2
| | | | | | None of the devices uses an usb led at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add device DLINK DWR-512-BGiuseppe Lippolis2016-11-235-0/+142
| | | | | | | | | | | | | | | | | | | | | | The Dlink DWR-512-B modem is a ralink 5350 processor based embedding a 3G mini-pcie router. The oem JBOOT bootloader has to be replaced by a RT5350 SDK U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot configured for the RT5350 256MiB SDR. Main reason to change the bootloader is the encrypted header used to store the kernel image. In this way an image can only be generated using the propietary binboy tool (included in the GPL distribution from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs partition scheme. This is considered a big constraint (limited kernel size and inefficient usage of flash space). For interested people I pubblished the details of my investigation about the encrypted firmware header here: http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: do not append metadata to CY-SWR1100 factory imageMathias Kresin2016-11-231-1/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: cleanup dts files of mt7621 based boardsMathias Kresin2016-11-2320-184/+130
| | | | | | | | | | | | | | | | | | | | Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci in mt7621.dtsi and enable the nodes in the indiviual board dts files. The nodes require further device specific configuration anyway. Remove the m25p80@0 spi child node from mt7621.dtsi and add the chunked-io parameter to the individual board dts files. Fix the spi flash compatible string for the WNDR3700V5. Drop the mt7621-eval-board compatible string for all boards which are not the eval board. Drop the linux,modalias parameter from spi flash node. Remove the xhci node from board files, it is already enabled in dtsi. Disable xhci for boards not having usb ports populated. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: order mt7621.mk alphabeticalMathias Kresin2016-11-231-94/+94
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix wrong check for MT7621ATAndrew Yong2016-11-211-1/+1
| | | | | | | fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688) Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: Fix sdhci kernel panics on MT7621Andrew Yong2016-11-211-2/+2
| | | | | | | | | | | | | | Enable work-arounds present in the code commented-out but needed to write to sdcard on mt7621 which currently causes kernel to oops when engaging in serious writing to sdcard. With this change applied, there are still occasional warnings thrown by the mmc driver, however, at least it no longer crashes the system and even large writes (full-card dump/erase/write/compare) don't show any corruption. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions. Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: add support for WeVO W2914NS v2perillamint2016-11-218-0/+168
| | | | Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
* ramips: append metadata to imagesFelix Fietkau2016-11-197-22/+33
| | | | | | | metadata checks are not enforced yet, because some images are still being built by legacy code Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-187-0/+184
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add MT7620 MIB support for switch and portVitaly Chekryzhev2016-11-172-72/+351
| | | | | | | | | Move definitions to header. Replace array size definitions with macro. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [merged into 0513-net-mediatek-add-swconfig-driver-for-gsw_mt762x.patch] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: John Crispin <john@phrozen.org>
* ramips: add support for Sitecom WLR-6000Jasper Scholte2016-11-176-1/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the file is way to big for only including a kernel. The factory image need to have the dlf file extension. Otherwise the Sitecom firmware rejects the file. The stock firmware uses the following mac addresses: LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr) 2,4: 00:0C:F6:AA:BB:D8 (EEPROM) 5: 00:0C:F6:AA:BB:DC (EEPROM) WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr) Assuming the mac address range :D8 to :DC is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: 2.4GHz: 00:0C:F6:AA:BB:D8 LAN: 00:0C:F6:AA:BB:D9 WAN: 00:0C:F6:AA:BB:DA 5 GHz: 00:0C:F6:AA:BB:DC The first MAC is assigned to the 2.4GHz WiFi interface to keep compatibility with the SSIDs printed on the case, which have the last three sextets of the MAC address appended. There are still issues with the rt2x00 driver. It is not possible to use both wireless interfaces at the same time. The 2.4 GHz wireless (PCIe) only works if the internal 5GHz wireless is/has been enabled or used for scanning. The internal 5GHz wireless only works if the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz after it was enabled will result in stations seeing the 5Ghz AP but are unable to connect. Due to the not optimal working wifi the manufacture, backup and storage partitions of the OEM firmware are kept for now to allow an easy switch back to the Sitecom firmware. Signed-off-by: Jasper Scholte <NightNL@outlook.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Digineo AC1200 ProDominik Menke2016-11-176-4/+33
| | | | | | This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash. Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: cleanup ZBT-WG3526.dtsiDominik Menke2016-11-171-6/+6
| | | | | | | | - replace magic numbers with GPIO_* constants - replace generic PCI definitions with correct vendor and device identification Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: split ZBT-WG3526.dts into dtsi and dts filesDominik Menke2016-11-172-112/+120
| | | | Signed-off-by: Dominik Menke <dom@digineo.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 16:41:18 +0000