aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ELECOM WRC-1750GS/GSVINAGAKI Hiroshi2020-07-163-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. WRC-1750GSV has the same hardware with WRC-1750GS. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-1750GS (or WRC-1750GSV) normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button for WRC-1750GS : wrc-1750gs-squashfs-factory.bin for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin 4. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for D-Link DIR-878 A1Mathieu Martin-Borret2020-07-133-1/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB NOR SPI flash WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) LAN: 5x1000M Firmware layout is Uboot with extra 96 bytes in header Base PCB is AP-MTKH7-0002 LEDs Power Green,Power Orange,Internet Green,Internet Orange LEDs "2.4G" Green & "5G" Green connected directly to wifi module Buttons Reset,WPS,WIFI Flashing instructions: Upload image via emergency recovery mode Push and hold reset button (on the back of the device) until power led starts flashing (about 10 secs or so) while powering the device on. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Some browsers/OS combinations are known not to work, so if you don't see the percentage complete displayed and moving within a few seconds, restart the procedure from scratch and try anoher one, or try the command line way. Alternative method using command line on Linux: curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1 Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com> [use of generic uimage-padhdr in image generation code] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: consolidate Netgear devices for mt7628Adrian Schmutzler2020-07-137-283/+151
| | | | | | | | | | | | | | | This creates a common DTSI and shared image definition for the relatively similar Netgear devices for mt7628 platform. As a side effect, this raises SPI flash frequency for the R6120, as it's expected to work there as well if it works for R6080 and R6020. Based on the data from the other devices, it also seems probable the 5g MAC address for R6120 could be extracted from the caldata, and the mtd-mac-address there could be dropped. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate recipes with uimage_padhdrAdrian Schmutzler2020-07-113-13/+8
| | | | | | | | | | | There are already two very similar recipes using uimage_padhdr in ramips target, and a third one is about to be added. Make the recipe more generic, so redefinitions are not necessary anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
* ramips: mt7621: refactor set affinity scriptDENG Qingfang2020-07-111-19/+7
| | | | | | | | The current one only looks for mt76x2e and mt7603e, and does not work for 2 or more same Wi-Fi chips. Refactor the script to cover those cases. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: kernel: fix awake-rt305x-dwc2 patchAlexey Dobrovolsky2020-07-111-7/+7
| | | | | | | | | | | | | At this point in v5.4 kernel we cannot use dwc2_readl() and dwc2_writel() since they rely on the value hsotg->needs_byte_swap which cannot be obtained before the controller wakes up. We should use readl() and writel() to wake up the controller before calling dwc2_check_core_endianness(). Fixes: 6be0da90a165 ("ramips: refresh patches") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [fixed Fixes: tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Netgear R6020Tim Thorpe2020-07-104-0/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6020, aka Netgear AC750. The R6020 appears to be the same hardware as the Netgear R6080, aka Netgear AC1000, but it has a slightly different flash layout, and no USB ports. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB MAC addresses based on vendor firmware: LAN *:88 0x4 WAN *:89 WLAN2 *:88 0x4 WLAN5 *:8a 0x8004 The factory partition might have been corrupted beforehand. However, the comparison of vendor firmware and OpenWrt still allowed to retrieve a meaningful assignment that also matches the other similar devices. Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6020, and power the R6020 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6020. After flashing has finished, power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Tim Thorpe <timfthorpe@gmail.com> [slightly extend commit message, fix whitespaces in DTS, align From: with Signed-off-by] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: use lzma-loader for ra21s & rg21sFurkan Alaca2020-07-081-0/+2
| | | | | | | | | | The rg21s fails to boot if the kernel is larger than about 2,376 KiB. The ra21s is virtually identical hardware. Enabling lzma-loader resolves the issue on both the rg21s and ra21s (see FS#3057 on the issue tracker). Fixes: FS#3057 Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
* ramips: add support for ZyXEL Keenetic Lite Rev.BSergei Burakov2020-07-083-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: SoC: RT5350 CPU Frequency: 360 MHz Flash Chip: Macronix MX25L6406E (8192 KiB) RAM: Winbond W9825G6JH-6 (32768 KiB) 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) 1x external antenna UART (J1) header on PCB (57800 8n1) Wireless: SoC-intergated: 2.4GHz 802.11bgn USB: None 8x LED, 2x button Flash instruction: Configure PC with static IP 192.168.99.8/24 and start TFTP server. Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin" to "rt305x_firmware.bin" and place it in TFTP server directory. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
* ramips: move adslr_g7 in image/mt7621.mk to keep sortingAdrian Schmutzler2020-07-081-8/+8
| | | | | | | Move this device to the top to maintain alphabetic sorting in the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add missing kmod-mt7615-firmware for TP-Link RE500 v1Adrian Schmutzler2020-07-081-1/+1
| | | | | | | | | Adding this has been overlooked when rebasing the commit prior to merge. Fixes: ba0f4f0cfddc ("ramips: add support for TP-Link RE500 v1") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)Bjørn Mork2020-07-085-0/+213
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621ST WiFi: MediaTek MT7603 Quantenna QT3840BC Flash: 128M NAND RAM: 64M LED: Dual colour red and green BTN: Reset WPS Eth: 4 x 10/100/1000 connected to MT7621 internal switch MT7621 RGMII port connected to Quantenna module GPIO: Power/reset of Quantenna module Quantenna module ---------------- The Quantenna QT3840BC (or QV840) is a separate SoC running another Linux installation. It is mounted on a wide mini-PCIe form factor module, but is connected to the RGMII port of the MT7621. It loads both a second uboot stage and an os image from the MT7621 using tftp. The module is configured using Quantenna specific RPC calls over IP, using 802.1q over the RGMII link to support multiple SSIDs. There is no support for using this module as a WiFi device in OpenWrt. A package with basic firmware and management tools is being prepared. Serial ports ------------ Two serial ports with headers: RRJ1 - 115200 8N1 - Connected to the Quantenna console J1 - 57600 8N1 - Connected to the MT7621 console Both share pinout with many other Zyxel/Mitrastar devices: 1 - NC (VDD) 2 - TX 3 - RX 4 - NC (no pin) 5 - GND Dual system partitions ---------------------- The vendor firmware and boot loader use a dual partition scheme storing a counter in the header of each partition. The partition with the highest number will be selected for boot. OpenWrt does not support this scheme and will always use the first OS partition. It will reset both counters to zero the first time sysupgrade is run, making sure the first partition is selected by the boot loader. Installation from vendor firmware --------------------------------- 1. Run a DHCP server. The WAP6805 is configured as a client device and does not have a default static IP address. Make a note of which address it is assigned 2. tftp the OpenWrt initramfs-kernel.bin image to this address. Wait for the WAP6805 to reboot. 3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a backup of all mtd partitions now. The last used OEM image is still present in either "Kernel" or "Kernel2" at this point, and can be restored later if you save a copy. 4. sysupgrade to the OpenWrt sysupgrade.bin image. Installation from U-Boot ------------------------ This requires serial console access 1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to your tftp server directory. Configure the server address as 192.168.0.33/24 2. Hit ESC when the message "Hit ESC key to stop autoboot" appears 3. Type "ATGU" + Enter, and then "2" immediately after pressing enter. 4. Answer Y to the question "Erase Linux in Flash then burn new one. Are you sure?", and answer the address/filename questions. Defaults: Input device IP (192.168.0.2) Input server IP (192.168.0.33) Input Linux Kernel filename ("ras.bin") 5. Wait until after you see the message "Done!" and power cycle the device. It will hang after flashing. 6. Continue with step 3 and 4 from the vendor firmware procedure. Notes on the WAP6805 U-Boot --------------------------- The bootloader has been modified with both ZyXELs zyloader and the device specific dual partition scheme. These changes appear to have broken a few things. The zyloader shell claims to support a number of ZyXEL AT commands, but not all of them work. The image selection scheme is unreliable and inconsistent. A limited U-Boot menu is available - and used by the above U-Boot install procedure. But direct booting into an uploaded image does not work, neither with ram nor with flash. Flashing works, but requires a hard reset after it is finished. Reverting to OEM firmware ------------------------- The OEM firmware can be restored by using mtd write from OpenWrt, flashing it to the "Kernel" partition. E.g. ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin OEM firmwares for the WAP6805 are not avaible for public download, so a backup of the original installation is required. See above. Alternatively, firmware for the WAP6806 (Armor X1) may be used. This is exactly the same hardware. But the branding features do obviously differ. LED controller -------------- Hardware implementation is unknown. The dual-color LED is controlled by 3 GPIOs: 4: red 7: blinking green 13: green Enabling both red and green makes the LED appear yellow. The boot loader enables hardware blinking, causing the green LED to blink slowly on power-on, until the OpenWrt boot mode starts a faster software blink. Signed-off-by: Bjørn Mork <bjorn@mork.no> [fix alphabetic sorting for image build statement] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Add support for Xiaomi Mi Router(Black,R2100)Emir Efe Kucuk2020-07-087-155/+215
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many characteristics (apart from its looks and the GPIO ports) with the 6-antenna *white* "Xiaomi Redmi Router AC2100" See the visual comparison of the two routers here: https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg Specification of R2100: - CPU: MediaTek MT7621A - RAM: 128 MB DDR3 - FLASH: 128 MB ESMT NAND - WIFI: 2x2 802.11bgn (MT7603) - WIFI: 4x4 802.11ac (MT7615) - ETH: 3xLAN+1xWAN 1000base-T - LED: Power, WAN in Yellow and Blue - UART: On board (Don't know where is should be confirmed by anybody else) - Modified u-boot Hacking of official firmware process is same at both RM2100 and R2100. Thanks to @namidairo Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide Guide is written for MacOS but it will work at linux. needed packages: python3(with scapy), netcat, http server, telnet client 1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware 2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1 3. nvram set uart_en=1 4. nvram set bootdelay=5 5. nvram set flag_try_sys1_failed=1 6. nvram commit 7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0 other than these I specified in here. Everything is same with: https://github.com/openwrt/openwrt/commit/f3792690c4f0567a8965d82898295b9d50c3bb7e Thanks for all community and especially for this device: @Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com) MAC Locations: WAN *:b5 = factory 0xe006 LAN *:b6 = factory 0xe000 WIFI 5ghz *:b8 = factory 0x8004 WIFI 2.4ghz *:b7 = factory 0x0004 Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com> [refactored common image bits into Device/xiaomi-ac2100, fixed From:] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax Gemini RE23SDavide Fioravanti2020-07-083-9/+191
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use WiFi LED DT triggers for TP-Link RE650 v1Adrian Schmutzler2020-07-072-5/+7
| | | | | | | | | | | | This moves WiFi LED triggers from 01_leds to device tree. While at it, convert the labels there to lower case; this is more commonly used and the change will actually remove competition between DT trigger and leftover uci config on already installed systems. Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE500 v1Christoph Krapp2020-07-076-125/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device uses the same hardware as RE650 v1 which got supported in 8c51dde. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin from the RE500 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep state_default in DTS files, fix label-mac-device, use lower case for WiFi LEDs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: reduce spi-max-frequency for ipTIME A8004TSunguk Lee2020-07-061-2/+1
| | | | | | | | | | | | | | | | | | | Reduce spi-max-frequency for ipTIME A8004T and disable m25p,fast-read option. A8004T uses `en25qh128` for the MTD. This flash memory would allow 80MHz, sometimes kernel received wrong id value in initramfs installed router. (kernel expected `1c 70 18 1c 70 18`, but one of cases, it was `9c 70 18 1c 70 18`) In this case, openwrt can't detect the partition information, it would write the inccorect data to the firmware partition and also it would occur the bootlooping after sysupgrade. Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Update kernel 4.14 to version 4.14.187Hauke Mehrtens2020-07-044-8/+8
| | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Build tested: ramips Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for TP-Link RE220 v2Rowan Border2020-06-304-0/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at> for the TP-Link RE200 v2 as both devices share the same SoC, flash layout and GPIO pinout. Specifications MediaTek MT7628AN (580 Mhz) 64 MB of RAM 8 MB of FLASH 2T2R 2.4 GHz and 1T1R 5 GHz 1x 10/100 Mbps Ethernet UART header on PCB (57600 8n1) 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. Web Interface Installation It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Signed-off-by: Rowan Border <rowanjborder@gmail.com>
* ramips: remove duplicate MAC assignment caseDavid Bauer2020-06-291-5/+2
| | | | | | | | Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address at the same position in flash. Suggested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: David Bauer <mail@david-bauer.net>
* package: add ravpower-mcu packageDavid Bauer2020-06-291-1/+2
| | | | | | | This package allows to read battery status information and control the power state of the RAVPower RP-WD009 power management IC. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for RAVPower RP-WD009David Bauer2020-06-294-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD009 is a batter-powered pocket sized router with SD card lot and USB port. Hardware -------- CPU: MediaTek MT7628AN RAM: 64M DDR2 FLASH: 16M GigaDevices SPI-NOR WLAN: MediaTek MT7628AN 2T2R b/g/n MediaTek MT7610E 1T1R n/ac ETH: 1x FastEthernet SD: SD Card slot USB: USB 2.0 Custom PMIC on the I2C bus (address 0x0a). Installation ------------ 1. Press and hold down the reset button. 2. Power up the Device. Keep pressing the reset button for 10 more seconds until the Globe LED lights up. 3. Attach your Computer to the Ethernet port. Assign yourself the address 10.10.10.1/24. 4. Access the recovery page at 10.10.10.128 and upload the OpenWrt factory image. 5. The flashing will take around 1 minute. The device will reboot automatically into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for WAVLINK WL-WN577A2Lars Wessels2020-06-294-1/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band wall-plug wireless router. In Germany this device is sold under the brand name Maginon WL-755 (white case): Device specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps (Ralink RT3050) - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER - Buttons: Reset, WPS - Small sliding power switch Flashing instructions (U-boot): - Configure a TFTP server on your PC/Laptop and set its IP to 192.168.10.100 - Rename the OpenWrt image to firmware.bin and place it in the root folder of the TFTP server - Power off (using the small sliding power switch on the left side) the device and connect an ethernet cable from its LAN or WAN port to your PC/Laptop - Press the WPS button (and keep it pressed) - Power on the device (using the small power switch) - After a few seconds, when the WAN/LAN LED stops blinking very fast, release the WPS button - Flashing OpenWrt takes less than a minute, system will reboot automatically - After reboot the WPS LED will indicate the current OpenWrt running status Signed-off-by: Lars Wessels <software@bytebox.org> [removed unused labels - fix whitespace errors - wrap commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for NETGEAR WAC124Jan Hoffmann2020-06-274-0/+39
| | | | | | | | | | | | | | | | | | | | | The WAC124 hardware appears to be identical to R6260/R6350/R6850. SoC: MediaTek MT7621AT RAM: 128M DDR3 FLASH: 128M NAND (Macronix MX30LF1G18AC) WiFI: MediaTek MT7603 bgn 2T2R MediaTek MT7615 nac 4T4R ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN) USB: 1x USB 2.0 BTN: Reset, WPS LED: Power, Internet, WiFi, USB (all green) Installation: The factory image can be flashed from the stock firmware web interface or using nmrpflash. With nmrpflash it is also possible to revert to stock firmware. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Netgear R6080Alex Lewontin2020-06-274-0/+170
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6080, aka Netgear AC1000. The R6080 has almost the same hardware as the Netgear R6120, aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and uses a different SERCOMM_HWID. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6080, and power the R6080 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6080. After flashing has finished, power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [rebase and adjust for 5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix sd pollingQin Wei2020-06-271-0/+4
| | | | | | | | | | This is fixed in 18.06, it appears again in 19.07. Currently mt7628 sdcard driver do not support polling mode which is for the device do not have card-detect pin to detect sd card insert. Without this patch, device will not detect sdcard is inserted. This patch is a fix of that. Signed-off-by: Qin Wei <support@vocore.io>
* ramips: drop redundant chosen/bootargsAdrian Schmutzler2020-06-2514-57/+1
| | | | | | | chosen/bootargs are defined to the same value in device DTS files that is already set in the SoC DTSI. Remove the redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: clean up Netgear R6120 code formattingAlex Lewontin2020-06-231-1/+1
| | | | | | | This commit performs minor janitorial work to clean up some code formatting for the Netgear R6120. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ramips: move Netgear R6120 LED trigger to DTSAlex Lewontin2020-06-232-6/+3
| | | | | | | | | | | | This moves the trigger for the Netgear R6120's wlan2g_green LED from base-files/etc/board.d/01_leds to the device-tree file. This has been applied to R6120 based on findings for the very similar Netgear R6080. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [merge case in 01_leds, slightly adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.48Petr Štetiar2020-06-221-5/+6
| | | | | | | | | | | | | | | | Resolved merge conflict in the following patches: layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch Refreshed patches, removed upstreamed patch: bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch Run tested: qemu-x86-64 Build tested: x86/64 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ELECOM WRC-2533GST2INAGAKI Hiroshi2020-06-215-31/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 32 MiB - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-2533GST2 normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add MT7615 wireless support for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-212-1/+30
| | | | | | | | | ELECOM WRC-1900GST and WRC-2533GST have two MT7615 chips for 2.4/5 GHz wireless. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: increase SPI frequency for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-211-1/+1
| | | | | | | | | | | Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST to 40 MHz by updating the common DTSI file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [split patch, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label-mac-device for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-211-1/+2
| | | | | | | | | | | Update the dtsi for ELECOM WRC-1900GST and WRC-2533GST to add label-mac-device alias. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [split patch, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.46Petr Štetiar2020-06-161-2/+2
| | | | | | | | | Refreshed patches. Run tested: qemu-x86-64, wrt3200acm Build tested: x86/64, imx6, mvebu/cortexa9, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-168-15/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix IPv4-only corner case in 01_enable_packet_steeringAdrian Schmutzler2020-06-151-0/+1
| | | | | | | | | | | | | | | | The uci config section network.globals set up in /bin/config_generate will only be created if /proc/sys/net/ipv6 exists. Correspondingly, lacking IPv6 support, the command uci set network.globals.packet_steering=1 will fail with "uci: Invalid argument" as the network.globals config has not been set up. Fix that by adding the setup there as well. Fixes: dfd62e575c6c ("ramips: enable packet steering by default on mt7621") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop useless label-mac-device for RouterBOARD 750Gr3Adrian Schmutzler2020-06-131-1/+0
| | | | | | | | | | | | | | With the new driver, MAC addresses are not set up in DTS anymore, and therefore label-mac-device will be useless there. Setup is done properly in 02_network, so this just removes the obsolete alias. Fixes: 5e50515fa6b3 ("ramips/mt7621: mikrotik: don't use mtd-mac-address in DTS") Suggested-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix port display for TRENDnet TEW-810DRJ. Scott Heppler2020-06-121-1/+1
| | | | | | | | | | This updates the display port order for the TEW-810DR to be in line with the DIR-810L. Both share the same board and pictures on the vendors' pages indicate the same external numbering scheme as well. Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [replace commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add support for NETGEAR WAC104Pawel Dembicki2020-06-124-1/+186
| | | | | | | | | | | | | | | | | | | | | | | | NETGEAR WAC104 is an AP based on castrated R6220, without WAN port and USB. SoC: MediaTek MT7621ST RAM: 128M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7612EN an+ac MediaTek MT7603EN bgn ETH: MediaTek MT7621ST (4x LAN) BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: 7x (3x GPIO controlled) Installation: Login to netgear webinterface and flash factory.img Back to stock: Use nmrpflash to revert stock image. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix port display for D-Link DIR-810LAdrian Schmutzler2020-06-111-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | The port order displayed in LuCI is currently inverted for this devices: LuCI - Device LAN1 - LAN4 LAN2 - LAN3 LAN3 - LAN2 LAN4 - LAN1 Fix it. Strangely, the owner of a TRENDnet TEW-810DR reports that the initial port order is correct, while both devices share the same board and look similar from the outside. Since I cannot investigate this without having any of the devices, this does only touch the DIR-810L for now. While at it, also merge in the case for zbtlink,zbt-we2026, as the display port specified for WAN there won't have any effect anyway. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix WAN LED for D-Link DIR-810L/TRENDnet TEW-810DRAdrian Schmutzler2020-06-114-20/+19
| | | | | | | | | | | | | | | | | | The WAN LED on DIR-810L was actually blinking on LAN1 port activity. This has already been improved for the TEW-810DR, where the GPIO has been set up explicitly rather than having it controlled by the switch. This patch also applies this setup to the DIR-810L. In addition, the trigger in 01_leds is set up with ucidef_set_led_switch for both devices now, so state changes should be displayed correctly as well. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L] Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
* ramips: limit uci commit to the changed config fileAdrian Schmutzler2020-06-111-1/+1
| | | | | | | Since 01_enable_packet_steering only touches the network config, limit the uci commit to this as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use amber LED for boot/failsafe on Netgear EX3700/EX6130Adrian Schmutzler2020-06-112-16/+16
| | | | | | | | | According to the manual, the amber power LED is used to indicate boot, while the green LED is meant to indicate a running system. While at it, also adjust the DT node names for all LEDs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6120Adrian Schmutzler2020-06-116-2/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * CPU: 580 MHz * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The device is identical to the EX6130 except for the mains socket and the hardware ID. Installation: The -factory images can be flashed from the device's web interface or via nmrpflash. Notes: MAC addresses were set up based on the EX6130 setup. This is based on prior work of Adam Serbinski and Mathias Buchwald. Tested by Mathias Buchwald. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add mt7621 ethernet driver improvementsFelix Fietkau2020-06-102-0/+98
| | | | | | | - Speed up MDIO bus access - Improve performance on tx completion Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: enable packet steering by default on mt7621Felix Fietkau2020-06-101-0/+4
| | | | | | | It provides a significant performance boost, especially with flow offloading enabled Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: erx and erx-sfp: fix missing WAN interfacePerry Melange2020-06-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), this change was discussed in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452 With commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), all the ports were put into the LAN bridge, with the argument that the OEM firmware does not have a WAN port enabled. In the default OEM setup, all of the ports except eth0 are dead and eth0 is set to a static IP address without providing DHCP services when connected. It is only after the wizard has been run that eth0 becomes the WAN port and all the rest of the ports belong to LAN with DHCP enabled. Having all of the ports set to the LAN bridge does not mirror the default OEM setup. To accomplish that, then only eth0 would be in the LAN bridge. But this is not the expected behaviour of OpenWrt. Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides the expected behaviour expected from OpenWrt, maintains the current documentation as up-to-date, and does not require the user to manually detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set eth0 to the WAN(6) interface(s). Fixes: 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses") Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips/mediatek: select kmod-mt7615-firmware where kmod-mt7615e is selectedFelix Fietkau2020-06-041-26/+26
| | | | | | | The new mt76 version splits out the firmware, because the driver can also be used for MT7663/MT7613 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621: use higher SPI clock speed on Mikrotik rbm11g and rbm33gTobias Schramm2020-06-032-5/+3
| | | | | | | | | Previously the dts were using a value determined by empirical testing, because of a spi driver/clock bug. The bug was fixed quite some time ago. 33 MHz is the default clock frequency used by RouterBOOT and thus safe. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 08:28:27 +0000