aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: WN3000RPv3: do not setup switchThibaut VARENE2017-04-281-1/+0
| | | | | | | | | The WN3000RPv3 is a repeater with a single ethernet port. Setting up the switch, even to disable it, is unnecessary and possibly confusing. Configure LAN as eth0 instead. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add support for Sanlinking D240Kristian Evensen2017-04-287-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: fix Sercomm NA930 compatible stringMathias Kresin2017-04-281-1/+1
| | | | | | | The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use the eval board compatible string. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove Planex CS-QR10 sound device tree nodeMathias Kresin2017-04-281-11/+0
| | | | | | | | The comptible string is neither added by any LEDE patch nor exists in in the kernel. Drop the sound node which was obviously added accidentally with 9195d8da ("ramips: DTS rework"). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: cleanup SPI flash device tree properties usageMathias Kresin2017-04-28110-116/+6
| | | | | | | | | Use only the jedec,spi-nor compatible string. Everything else either never worked or is only support to keep compatibility. Remove the linux,modalias property. It is obsolete since kernel 4.4. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove DT pcie nodes for GL-MT300A/NFelix Fietkau2017-04-282-26/+0
| | | | | | These devices don't have a secondary wifi chip Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb powerVitaly Chekryzhev2017-04-282-0/+22
| | | | | | Export gpio usb to allow power management of USB port. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Viva: align factory imagesVitaly Chekryzhev2017-04-281-1/+1
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Viva: export gpio usb powerVitaly Chekryzhev2017-04-281-0/+11
| | | | | | Export gpio usb to allow power management of USB port. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add ip17xx support to WLI-TX4-AG300NYo Abe2017-04-281-0/+1
| | | | | | | | | ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which should be included by default. Signed-off-by: Yo Abe <abe.geel@gmail.com> [Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: fix EX2700 wireless macJoseph C. Lehner2017-04-281-13/+11
| | | | | | | | On some EX2700 devices, the MAC address from the eeprom data differs from the actual MAC address. Fix that, and cleanup the DTS file while we're at it. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: ZyXEL Keenetic series update wan macVitaly Chekryzhev2017-04-281-1/+3
| | | | Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Omni align factory imagesVitaly Chekryzhev2017-04-281-2/+2
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: correct keenetic-series switch indexVitaly Chekryzhev2017-04-281-1/+1
| | | | | | Fix switch name typo Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add support for Netgear WN3000RPv3Thibaut VARENE2017-04-287-2/+163
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: fix mac address of miwifi-miniBangLang Huang2017-04-282-1/+5
| | | | | | | For the miwifi-mini, the offset of ethernet mac should be 0x28 which you can easyily dump from 'Factory' partition. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: Clean duplicated status property for Omega2 WMAC in dtsiFurong Xu2017-04-281-4/+0
| | | | | | At the tail of dtsi, wmac is enabled twice, clean the first one Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: fixed sms led polarity into dwr-512 DTGiuseppe Lippolis2017-04-281-1/+1
| | | | Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: WN3000RPv3: do not setup switchThibaut VARENE2017-04-281-0/+1
| | | | | | | | | The WN3000RPv3 is a repeater with a single ethernet port. Setting up the switch, even to disable it, is unnecessary and possibly confusing. Configure LAN as eth0 instead. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter XMatthias Schiffer2017-04-221-1/+1
| | | | | | Fixes removal of unneeded kernel modules with per-device rootfs. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: update kernel 4.4 to 4.4.61Jo-Philipp Wich2017-04-151-21/+0
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add RP-N53 pcie wireless eepromMathias Kresin2017-04-121-0/+9
| | | | | | | | | | Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata. Disable the 2.4GHz band as this band has no antennas attached but is enabled in the eeprom/caldata. Fixes: FS#691 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix WHR-600D eeprom dt propertyMathias Kresin2017-04-121-3/+3
| | | | | | | | | | | Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as this board have a RT5592 and uses the rt2x00 driver. The mediathek device tree bindings do not work here. Fixes: FS#691 Fixes: d8dd207ea6f2 ("ramips: use the ralink,mtd-eeprom device tree property") Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update kernel 4.4 to 4.4.59Hauke Mehrtens2017-04-025-37/+7
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix Linksys RE6500 switch port mappingJo-Philipp Wich2017-03-071-1/+4
| | | | | | | | Properly map the internal switch ports to the proper LAN1..LAN4 labels. Fixes #530. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: fix Airlink AR725W device titleMathias Kresin2017-03-011-1/+1
| | | | | | Gemtek is the ODM but the board was sold by Airlink101. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix the number of uarts for MT7688Furong Xu2017-02-161-2/+2
| | | | | | Same as MT7621 and MT7628, MT7688 allows up to 3 uarts Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: fix PWM pin mux conflict in dtsiFurong Xu2017-02-161-4/+0
| | | | | | | | | | | | | GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict [ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm [ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22 [ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux [ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back Keep PWM disabled. Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: added image size into dwr-512 DTGiuseppe Lippolis2017-02-131-0/+1
| | | | Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: Correct switch configuration for Newifi D1Chuanhong Guo2017-02-131-4/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix AR670W partition alignmentClaudio Leite2017-02-081-1/+1
| | | | | | | mtdsplit_lzma requires that the rootfs be aligned to a block boundary. Pad the kernel partition to make this so. Signed-off-by: Claudio Leite <leitec@gmail.com>
* Kernel: bump to 4.4.44Stijn Segers2017-02-061-4/+4
| | | | | | | | | | | | | | Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64. .44 has been run-tested on the 17.01 branch here on ar71xx and mt7621. Signed-off-by: Stijn Segers <francesco.borromini@inventati.org> (cherry picked from commit 20996edd68b8a0b139bdb36b3aafa29c037d4bda) Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Conflicts: target/linux/ar71xx/patches-4.4/920-usb-chipidea-AR933x-platform-support.patch target/linux/ar71xx/patches-4.4/930-chipidea-pullup.patch
* ramips: fix Airlink AR725W factory image buildMathias Kresin2017-02-041-2/+5
| | | | | | | | | | | | | The factory image can't be bigger than 3328 KByte. If the image is bigger than that, the gemtek-header tool throws an error and breaks the build. Make sure the output file to which the gemtek header should be added exists and wasn't removed during the check-size step because of it size. This will prevent hard errors in case the factory image is to big similar to what is done for sysupgrade images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add missing DTS pcie node for WSR-600Felix Fietkau2017-01-311-0/+21
| | | | | | Enables PCI bus and support for the MT7603 and RT5592 chips Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: remove mips16 feature flag from target makefilesFelix Fietkau2017-01-241-1/+1
| | | | | | | It can be implicitly derived from the MIPS32 revision support in the kernel configuration Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips/rt288x: switch CPU_TYPE to 24kcFelix Fietkau2017-01-241-1/+1
| | | | | | | | | | | While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2 architecture just like the 24Kc, so the instruction set should be 100% compatible. Switching it to 24kc allows it to share the package architecture with a lot of other targets instead of creating a special case, saving buildbot resources. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add back the i2c-mt7621 moduleJohn Crispin2017-01-151-0/+16
| | | | | | mt7628/88 are still using this module. Signed-off-by: John Crispin <john@phrozen.org>
* ramips: Added Onion Omega2 and Omega2+Lazar Demin2017-01-158-0/+249
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io>
* ramips: Add I2C driver to the default kernel configRosen Penev2017-01-153-23/+7
| | | | | | | | | | I made a commit that added the RTC driver to the kernel config with the intent that it would fix hctosys. Unfortunately while the RTC driver is in there, it's connected through I2C, the driver for which comes in module form and is thus loaded late. After this commit, it works fine. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: backport MIPS changes introducing a separate IRQ stackFelix Fietkau2017-01-152-2/+2
| | | | | | | | Prevents crashes when IRQs arrive when the current kernel stack context already contains deeply nested function calls, e.g. when stacking lots of network devices on top of each other Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update 4.4 kernel to 4.4.42Hauke Mehrtens2017-01-134-14/+9
| | | | | | | Refresh patches on all 4.4 supported platforms. Compile & run tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix WLI-TX4-AG300N boot and networkYo Abe2017-01-131-2/+11
| | | | | | | | | | | | | | | | Partition label "linux" prevents the root file system to be mounted at boot time leading to a kernel panic. After changing it to "firmware", the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data" are correctly recognized. The attached IP175C 10/100 MBit switch cannot connect to a link with fixed 1000Mbit speed. The correct link speed is 100MBit. The switch is detected and can be configured via mdio bus and should allow two separable VLANs to be configured for the 4 available ports. Signed-off-by: Yo Abe <abe.geel@gmail.com> [picked from openwrt/PR#330] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for VoCore2Andrew Yong2017-01-137-0/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: rt3883: fix typo in pinctrl lna_g_funcDaniel Golle2017-01-131-0/+26
| | | | | | | | Spotted by forum users https://forum.openwrt.org/viewtopic.php?pid=347439#p347439 Reported-by: Tom Psyborg <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: Fix VLAN limits for MT7621 GSWAntonis Kanouras2017-01-101-1/+5
| | | | | | | | | Without this patch swconfig will only allow setting up a total of 16 VLANs, with VLAN ID range of 0-15. Tested on ubnt-erx. Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
* kernel: remove ubifs xz decompression supportFelix Fietkau2017-01-091-1/+0
| | | | | | | It has been unused, and less useful than squashfs for cases where flash space usage matters. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump to 4.4.40Hauke Mehrtens2017-01-061-14/+0
| | | | | | | Refresh patches on all 4.4 supported platforms. Compile & run tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* build: use mkhash to replace various quirky md5sum/openssl callsFelix Fietkau2017-01-052-6/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: mtd: backport SPI_NOR_HAS_LOCKVictor Shyba2017-01-031-3/+3
| | | | | | | | | This flag was added to 4.9 with upstream commit 76a4707de5e18dc32d9cb4e990686140c5664a15. Signed-off-by: Victor Shyba <victor1984@riseup.net> [refresh and adjust platform patches, fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: MiWiFi Nano fixesL. D. Pinney2017-01-023-18/+31
| | | | | | | | | | | | | | | | Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 21:48:57 +0000