aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: convert DEVICE_TITLE to new variablesDaniel Golle2019-07-066-323/+704
| | | | | | Also unify naming and add details where they were missing. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for TP-Link TL-WR841n v14Alexander Müller2019-07-024-0/+155
| | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N. - MediaTek MT7628NN - 32 MB of RAM - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet Installation: - copy the 'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin' file to your tftp server root and rename it to 'tp_recovery.bin'. - configure your PC running the TFTP server with the static IP address 192.168.0.66/24 - push the reset button and plug in the power connector. Wait until the orange led starts blinking (~6sec) Signed-off-by: Alexander Müller <donothingloop@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
* ramips/leds: use devicetree alias led_wlanAlexander Couzens2019-07-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | Similiar to the lantiq target use a dts alias to define the wlan led instead of static mapping in /etc/board.d/01_leds. Reduce code duplication. A device tree must define the alias "led-wlan" similiar to "led-boot". / { aliases { led-wlan = &led_wlan; }; [..] led_wlan: wlan { label = "tl-wr841n-v14:green:wlan"; gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; }; }; Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for TOTOLINK A7000RChuanhong Guo2019-06-263-0/+133
| | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 128MB - Flash: 16M SPI NOR - Ethernet: 5x GE ports - WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: Upload generated sysupgrade firmware through factory web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: add IRQ for GPIO nodeChuanhong Guo2019-06-261-0/+3
| | | | | | This makes interrupt-based gpio-keys working. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: Add new device AsiaRF AP7621-001Daniel Danzberger2019-06-253-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specs: SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN) USB: 1x 3.0 PCI: 3x Mini PCIe GPS: Quectel L70B BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: The stock image is a modified openwrt and can be overflashed via # sysupgrade -F image.bin Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed unused label, formatting]
* kernel: bump 4.14 to 4.14.128Koen Vandeputte2019-06-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: fix EW-7478AC model name in DTSPetr Štetiar2019-06-201-1/+1
| | | | | | | | This fixes lower case AC in the DTS model name. Fixes: 88f7a29f99fb ("ramips: add support for Edimax EW-7476RPC / EW-7478AC") Reported-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix GELAN port in D-Link DWR-118-A2Pawel Dembicki2019-06-202-5/+7
| | | | | | | This patch fix and enable GELAN port in D-LINK DWR-118-A2. Tested-by: Richard Toth <trtk1992@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: add EPHY base mdio address changing possibilityPawel Dembicki2019-06-202-46/+62
| | | | | | | | | | | In some boards is requred to change the ephy mdio base address. This patch add of property "mediatek,ephy-base-address" in gsw part, which allows to change ephy base address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed indentation in header file] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: fix external PHY autopollingPawel Dembicki2019-06-201-4/+6
| | | | | | | | | | | | | | | | | The port initialisation is based on assumption that phy address and port number is the same. SoC allow different numbers and some board have it. Use phy address instead the port number to make sure that correct addresses are polled. In situation when only one PHY with address 0x0 is conected to port 4, autopolling is broken. This patch make autopolling correct when port number and phy address are different. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: handle mdio address and switch port seperateMathias Kresin2019-06-204-11/+14
| | | | | | | | | | | | | | | The phy handling code forces a phy mdio address and the switch port to which a phy is attached to be the same. Albeit such a configuration is used for most boards, it isn't for all. Pass the switch port number to the ethernet phy connect functions, to ensure the correct list entry is edited and not the list entry that matches th phys mdio address. Use the mdio address with mdiobus_get_phy instead of the port number, to make sure the expected ethernet phy gets connected. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: ignore already handled ethernet physMathias Kresin2019-06-201-2/+8
| | | | | | | | | | | | The whole logic in fe_phy_connect() is based on the asumption that mdio address and switch port id are equal. Albeit it is true for most boards, it doesn't is for all. It isn't yet clear which subtargets/boards require the devicetree less ethernet phy handling. Hence change the code in a way that it doesn't touch ethernet phys which were early attached and are already handled. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Edimax EW-7478APCBirger Koblitz2019-06-203-1/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN) USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header) BTN: Reset/WPS LED: - Power (white) - Internet (blue) - Wifi (blue) - USB (blue) UART: UART is present as Pads with throughholes on the PCB. They are located in the lower right corner (GbE ports facing up) 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimax.setup) Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflicts in 01_leds and mt7620.mk, dts whitespace issues] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax EW-7476RPC / EW-7478ACBirger Koblitz2019-06-207-0/+349
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: 192.168.9.2/24). http://192.168.9.2/index.asp ramips: add Edimax EW-7478AC SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimaxext.setup) Or push wpa button on power on and send firmware via tftp to 192.168.1.6 The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal antennas it has 2 external ones. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflict in 01_leds] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-122-4/+4
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: Remove redundant LED-casesKristian Evensen2019-06-101-68/+32
| | | | | | | 01_leds has several redundant LED-cases. This commit cleans up the file by merging these cases into shared cases. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TOTOLINK LR1200Chuanhong Guo2019-06-053-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7628DAN (MT7628AN with 64MB built-in RAM) - Flash: 8M SPI NOR - Ethernet: 5x 10/100Mbps - WiFi: 2.4G: MT7628 built-in 5G: MT7612E - 1x miniPCIe slot for LTE modem (only USB pins connected) - 1x SIM slot Flash instruction: U-boot has a builtin web recovery page: 1. Hold the reset button while powering it up 2. Connect to the ethernet and set an IP in 192.168.1.0/24 range 3. Open your browser and upload firmware through http://192.168.1.1 Note about the LTE modem: If your router comes with an EC25 module and it doesn't show up as a QMI device, you should do the following to switch it to QMI mode: 1. Install kmod-usb-serial-option and a terminal software (e.g. minicom or screen). All 4 serial ports of the modem should be available now. 2. Open /dev/ttyUSB3 with the terminal software and type this AT command: AT+QCFG="usbnet",0 3. Power-cycle the router. You should now get a QMI device recognized. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1Pawel Dembicki2019-06-051-0/+5
| | | | | | | | | Support for D-Link DWR-118 A1 was added before LEDs feature in mt76x0e driver. This fixes the 5GHz WiFi LED which was previously inverted. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: ethernet: remove unused SIOCETHTOOL ioctl handlingPetr Štetiar2019-06-051-12/+1
| | | | | | | | | | | | | This ioctl is currently routed through generic interface code. dev_ioctl dev_ethtool __ethtool_get_link_ksettings phy_ethtool_ioctl Cc: Felix Fietkau <nbd@nbd.name> Cc: John Crispin <john@phrozen.org> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: create R6220 dtsi and improve WNDR3700v5 supportJan Hoffmann2019-05-316-207/+166
| | | | | | | | | | | | | | | | | | The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and having a different casing. This adds a new cleaned up R6220.dtsi with the common bits for both devices. Both devices now have feature parity. Performed cleanup: * generic DTS node names * regulator for usb power * added missing pinctrl groups * use switch port instead of VLAN as trigger for WAN LED Fixes for WNDR3700v5: * all LEDS work * correct ethernet MAC addresses Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Xiaomi Mi Router 4A (100M Edition)Markus Scheck2019-05-313-0/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - SoC: MediaTek MT7628AN - Flash: 16MB (Winbond W25Q128JV) - RAM: 64MB - Serial: As marked on PCB, 3V3 logic, baudrate is 115200 - Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN) - WIFI0: MT7628AN 2.4GHz 802.11b/g/n - WIFI1: MT7612EN 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable power-LED (two-colored, yellow/blue) Non-programmable internet-LED (shows WAN-activity) - Buttons: Reset INSTALLATION: 1. Connect to the serial port of the router and power it up. If you get a prompt asking for boot-mode, go to step 3. 2. Unplug the router after > Erasing SPI Flash... > raspi_erase: offs:20000 len:10000 occurs on the serial port. Plug the router back in. 3. At the prompt select option 2 (Load system code then write to Flash via TFTP.) 4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the Server-IP. 5. Connect your computer to LAN1 and assign it as 192.168.1.2/24. 6. Rename the sysupgrade image to test.bin and serve it via TFTP. 7. Enter test.bin on the serial console and press enter. Signed-off-by: Markus Scheck <markus@mscheck.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added mt76 compatible]
* ramips: add CUDY WR1000 supportDavide Fioravanti2019-05-314-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas Specifications: MT7628 (580 MHz) 64 MB of RAM (DDR2) 8 MB of FLASH 2T2R 2.4 GHz (MT7628) 2T2R 5 GHz (MT7612E) 3x 10/100 Mbps Ethernet (2 LAN + 1 WAN) 2x external, non-detachable antennas (5dbi) UART header on PCB (57600 8n1) 7x LED, 2x button Known issues: The Power LED is always ON, probably because it is connected directly to power. Flash instructions ------------------ Load the ...-factory.bin image via the stock web interface. Openwrt upgrade instructions ---------------------------- Use the ...-sysupgrade.bin image for future upgrades. Revert to stock FW ------------------ Warning! This tutorial will work only with the following OEM FW: WR1000_EU_92.122.2.4987.201806261618.bin WR1000_US_92.122.2.4987.201806261609.bin If in the future these firmwares will not be available anymore, you have to find the new XOR key. 1) Download the original FW from the Cudy website. (For example WR1000_EU_92.122.2.4987.201806261618.bin) 2) Remove the header. dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64 3) XOR the new file with the region key. FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this: xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767.. Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!): https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false) 4) Check the resulting decrypted image. Check if bytes from 0x20 to 0x3f are: 4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Alternatively, you can use u-boot's tool dumpimage tool to check if the decryption was successful. It should look like: # dumpimage -l stock-firmware.bin Image Name: Linux Kernel Image Created: Tue Jun 26 10:24:54 2018 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB Load Address: 80000000 Entry Point: 8000c150 5) Flash it via forced firmware upgrade and don't "Keep Settings" CLI: sysupgrade -F -n stock-firmware.bin LuCI: make sure to click on the "Keep settings" checkbox to disable it. You'll need to do this !TWICE! because on the first try, LuCI will refuse the image and reset the "Keep settings" to enable. However a new "Force upgrade" checkbox will appear as well. Make sure to do this very carefully! Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added wifi compatible, spiffed-up the returned to stock instructions]
* ramips: unify JCG helper command definitionDavide Fioravanti2019-05-312-5/+6
| | | | | | | This patch makes the JCG helper command definition available for every rampis target Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for Telco Electronics X1Nicholas Smith2019-05-184-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 256MB DDR3 Flash: 16MB SPI-NOR WiFi: 2.4GHz: MT7603 @ PCIe0 WiFi: 5.8GHz: MT7612 @ PCIe1 Modem: Sierra Wireless MC74xx Interfaces: GBE RJ45 x5 mPCIe x2 UART x1 I2C x1 JTAG x1 UIM x1 LEDs x6 Flash instructions: Flash from within the factory bootloader, firmware web interface or CLI using sysupgrade -F -n Signed-off-by: Nicholas Smith <mips171@icloud.com>
* ramips: add factory image for WNDR3700v5Jan Hoffmann2019-05-183-17/+24
| | | | | | | | | This uses the existing rules for Sercomm factory images and moves them to the ramips image Makefile, so they can be used in all subtargets. The new factory image for WNDR3700v5 can be flashed using nmrpflash. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for HILINK HLK-7628NLiu Yu2019-05-184-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 128 MB Flash: 32 MB WIFI: 802.11n/g/b 20/40 MHz Ethernet: 5 Port ethernet switch UART: 2x Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART0 line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. 5. After firmware is started connect via ethernet at 192.168.1.1 Signed-off-by: Liu Yu <f78fk@live.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-175-1/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-176-1/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.118Koen Vandeputte2019-05-131-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch Altered: - 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: fix R6120 factory imageDavid Bauer2019-05-111-1/+1
| | | | | | | | | | | The factory firmware omits the JFFS2 end-marker while flashing via web-interface. Add a 64k padding after the marker fixes this problem. When the end-marker is not present, OpenWRT won't save the overlayfs after initial flash. Reported-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7620: fix dependenciesDeng Qingfang2019-05-111-1/+1
| | | | | | | | | | | | | MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies according to original Kconfig and lsmod output This will remove some unnecessary packages from MT7620 target to save some space Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 characters per line in the commit message]
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-144-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-133-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix pinctrl to allow hardware i2c on WRTNODE2RDaniel Golle2019-04-111-1/+11
| | | | | | | | Instead of assigning I2C pins as GPIOs by default, leave it up to the user whether to install kmod-i2c-mt7621 and use them for hardware I2C instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: correct DTS for Belkin F9K1109v1 to include switch definitionKip Porterfield2019-04-061-0/+11
| | | | | | | | | Add switch definition for the rtl8367b switch to the DTS/DTSi for the Belkin F9K1109v1 that was mistakenly omitted from the initial commit. Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1) Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ramips: backport mt7621-spi from linux-next-20190329Chuanhong Guo2019-04-061-261/+213
| | | | | | | | | | | | | Upstream driver has gone through a series of cleanup and was moved from drivers/staging into drivers/spi. Backport it to replace our messy driver. Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de> [LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module] Tested-by: Rosen Penev <rosenp@gmail.com> Tested-by: Tian Xiao bo <peterwillcn@gmail.com> [Newifi-D2 MediaTek MT7621 ver:1 eco:3] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: enable R6120 USB powerDavid Bauer2019-04-062-1/+16
| | | | | | | Enable the USB power for the Netgear R6120. Otherwise, no power is supplied to an attached USB device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-063-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* ramips: implement vlan rx offload on MT7621Felix Fietkau2019-04-033-4/+11
| | | | | | Avoids the overhead of software VLAN untagging in the network stack Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add missing SPDX identifier for EX6150David Bauer2019-03-311-0/+1
| | | | | | | This adds the SPDX license identifier for the NETGEAR EX6150. It was missed when submitting the original patch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Increase GB-PC1 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | The specific flash chip used (W25Q256FVEM) accepts 50MHz for read requests and higher for others. 104MHz for fast reads. ramips seems to be limited to 80MHz based on testing with higher values (no speedup). Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s [test done with backported upstream v4.19 driver[1], for numbers on stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI frequency to 80MHz` commit message] 1. https://github.com/openwrt/openwrt/pull/1578 Signed-off-by: Rosen Penev <rosenp@gmail.com> [expanded note about spi driver version] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Increase GB-PC2 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The flash chip on the board (Spansion S25FL256SAIF00) is rated to support at least 50MHz for normal read requests according to the datasheet. 133MHz for fast reads. However, ramips seems to be limited to 80MHz. >From testing this, higher values do not improve speeds. time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.82s to 14.09s. boot speed is also faster: [ 66.884087] procd: - init - vs [ 48.976049] procd: - init - Since spi speed was requested: [ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000 CPU is 900MHz: [ 0.000000] CPU Clock: 900MHz Signed-off-by: Rosen Penev <rosenp@gmail.com> [fixed commit message by adding missing 0 in the spi-mt7621 clock output] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add Netgear EX6150David Bauer2019-03-293-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621 RAM: 64M (Winbond W9751G6KB-25) FLASH: 16MB (Macronix MX25L12835F) WiFi: MediaTek MT7662E bgn 2SS WiFi: MediaTek MT7662E nac 2SS BTN: ON/OFF - Reset - WPS - AP/Extender toggle LED: - Arrow Right (blue) - Arrow Left (blue) - WiFi 1 (red/green) - WiFi 2 (red/green) - Power (green/amber) - WPS (Green) UART: UART is present as Pads on the backside of the PCB. They are located on the other side of the Ethernet port. 3.3V - GND - TX - RX / 57600-8N1 3.3V is the nearest one to the antenna connectors Installation ------------ Update the factory image via the Netgear web-interfaces (by default: 192.168.1.250/24). You can also use the factory image with the nmrpflash tool. For more information see https://github.com/jclehner/nmrpflash Signed-off-by: David Bauer <mail@david-bauer.net> [merge conflict in 02_network, flash@0 node rename, wlan DTS triggers] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ZyXEL Keenetic StartVladimir Kot2019-03-294-0/+132
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: RT5350F - CPU Frequency: 360 MHz - Flash Chip: Winbond 25Q32 (4096 KiB) - RAM: 32768 KiB - 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) - 1x external, non-detachable antenna - UART (J1) header on PCB (57800 8n1) - Wireless: SoC-intergated: 2.4GHz 802.11bgn - USB: None - 3x LED, 2x button Flash instruction: 1. Configure PC with static IP 192.168.1.2/24 and start TFTP server. 2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin" to "kstart_recovery.bin" and place it in TFTP server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. 4. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Vladimir Kot <vova28rus@gmail.com> [fixed git commit author and whitespace issues in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for WIZnet WizFi630S boardTobias Welz2019-03-293-0/+204
| | | | | | | | | | | | | | | | | | | | The WIZnet WizFi630S board is in the miniPCIe form factor. SoC: Mediatek MT7688AN RAM: 128MB Flash: 32Mb WiFi: 2.4GHz Ethernet: 3x 100Mbit USB: 1 (USB 2.0) serial ports: 2 (1x full, 1xlite) Flash and recovery instructions: Use the factory installed u-boot boot loader. It is available on UART2 (115200,8,n,1). Then get the sysupgrade image from a tftp server. Signed-off-by: Tobias Welz <tw@wiznet.eu> [whitespace and device name in makefile fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.108Koen Vandeputte2019-03-271-2/+2
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0033-i2c-bcm2835-Add-debug-support.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: allow packets with ttl=0Felix Fietkau2019-03-241-2/+2
| | | | | | | Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0. This trips up the TTL=0 check in the PPE if enabled. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-245-0/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-26 04:06:36 +0000