aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7620: fix dependenciesDeng Qingfang2019-05-111-1/+1
| | | | | | | | | | | | | MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies according to original Kconfig and lsmod output This will remove some unnecessary packages from MT7620 target to save some space Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 characters per line in the commit message]
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-144-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-133-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix pinctrl to allow hardware i2c on WRTNODE2RDaniel Golle2019-04-111-1/+11
| | | | | | | | Instead of assigning I2C pins as GPIOs by default, leave it up to the user whether to install kmod-i2c-mt7621 and use them for hardware I2C instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: correct DTS for Belkin F9K1109v1 to include switch definitionKip Porterfield2019-04-061-0/+11
| | | | | | | | | Add switch definition for the rtl8367b switch to the DTS/DTSi for the Belkin F9K1109v1 that was mistakenly omitted from the initial commit. Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1) Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ramips: backport mt7621-spi from linux-next-20190329Chuanhong Guo2019-04-061-261/+213
| | | | | | | | | | | | | Upstream driver has gone through a series of cleanup and was moved from drivers/staging into drivers/spi. Backport it to replace our messy driver. Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de> [LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module] Tested-by: Rosen Penev <rosenp@gmail.com> Tested-by: Tian Xiao bo <peterwillcn@gmail.com> [Newifi-D2 MediaTek MT7621 ver:1 eco:3] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: enable R6120 USB powerDavid Bauer2019-04-062-1/+16
| | | | | | | Enable the USB power for the Netgear R6120. Otherwise, no power is supplied to an attached USB device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-063-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* ramips: implement vlan rx offload on MT7621Felix Fietkau2019-04-033-4/+11
| | | | | | Avoids the overhead of software VLAN untagging in the network stack Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add missing SPDX identifier for EX6150David Bauer2019-03-311-0/+1
| | | | | | | This adds the SPDX license identifier for the NETGEAR EX6150. It was missed when submitting the original patch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Increase GB-PC1 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | The specific flash chip used (W25Q256FVEM) accepts 50MHz for read requests and higher for others. 104MHz for fast reads. ramips seems to be limited to 80MHz based on testing with higher values (no speedup). Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s [test done with backported upstream v4.19 driver[1], for numbers on stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI frequency to 80MHz` commit message] 1. https://github.com/openwrt/openwrt/pull/1578 Signed-off-by: Rosen Penev <rosenp@gmail.com> [expanded note about spi driver version] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Increase GB-PC2 SPI frequency to 80MHzRosen Penev2019-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The flash chip on the board (Spansion S25FL256SAIF00) is rated to support at least 50MHz for normal read requests according to the datasheet. 133MHz for fast reads. However, ramips seems to be limited to 80MHz. >From testing this, higher values do not improve speeds. time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.82s to 14.09s. boot speed is also faster: [ 66.884087] procd: - init - vs [ 48.976049] procd: - init - Since spi speed was requested: [ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000 CPU is 900MHz: [ 0.000000] CPU Clock: 900MHz Signed-off-by: Rosen Penev <rosenp@gmail.com> [fixed commit message by adding missing 0 in the spi-mt7621 clock output] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add Netgear EX6150David Bauer2019-03-293-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621 RAM: 64M (Winbond W9751G6KB-25) FLASH: 16MB (Macronix MX25L12835F) WiFi: MediaTek MT7662E bgn 2SS WiFi: MediaTek MT7662E nac 2SS BTN: ON/OFF - Reset - WPS - AP/Extender toggle LED: - Arrow Right (blue) - Arrow Left (blue) - WiFi 1 (red/green) - WiFi 2 (red/green) - Power (green/amber) - WPS (Green) UART: UART is present as Pads on the backside of the PCB. They are located on the other side of the Ethernet port. 3.3V - GND - TX - RX / 57600-8N1 3.3V is the nearest one to the antenna connectors Installation ------------ Update the factory image via the Netgear web-interfaces (by default: 192.168.1.250/24). You can also use the factory image with the nmrpflash tool. For more information see https://github.com/jclehner/nmrpflash Signed-off-by: David Bauer <mail@david-bauer.net> [merge conflict in 02_network, flash@0 node rename, wlan DTS triggers] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ZyXEL Keenetic StartVladimir Kot2019-03-294-0/+132
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: RT5350F - CPU Frequency: 360 MHz - Flash Chip: Winbond 25Q32 (4096 KiB) - RAM: 32768 KiB - 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) - 1x external, non-detachable antenna - UART (J1) header on PCB (57800 8n1) - Wireless: SoC-intergated: 2.4GHz 802.11bgn - USB: None - 3x LED, 2x button Flash instruction: 1. Configure PC with static IP 192.168.1.2/24 and start TFTP server. 2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin" to "kstart_recovery.bin" and place it in TFTP server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. 4. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Vladimir Kot <vova28rus@gmail.com> [fixed git commit author and whitespace issues in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for WIZnet WizFi630S boardTobias Welz2019-03-293-0/+204
| | | | | | | | | | | | | | | | | | | | The WIZnet WizFi630S board is in the miniPCIe form factor. SoC: Mediatek MT7688AN RAM: 128MB Flash: 32Mb WiFi: 2.4GHz Ethernet: 3x 100Mbit USB: 1 (USB 2.0) serial ports: 2 (1x full, 1xlite) Flash and recovery instructions: Use the factory installed u-boot boot loader. It is available on UART2 (115200,8,n,1). Then get the sysupgrade image from a tftp server. Signed-off-by: Tobias Welz <tw@wiznet.eu> [whitespace and device name in makefile fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.14 to 4.14.108Koen Vandeputte2019-03-271-2/+2
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0033-i2c-bcm2835-Add-debug-support.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: allow packets with ttl=0Felix Fietkau2019-03-241-2/+2
| | | | | | | Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0. This trips up the TTL=0 check in the PPE if enabled. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-245-0/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkdlinkfw: add kernel image offsetPawel Dembicki2019-03-242-33/+23
| | | | | | | | Some boards with JBOOT have partiton between bootloader and kernel image. This patch add possibility to change kernel partition start address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix wrong i2s clock unit from kHz to MHzQin Wei2019-03-241-1/+1
| | | | | | | | | | | clk_get_rate returns the current clock rate in Hz for a clock source so if we divide it by 1M, then we get frequency in MHz and not kHz. Signed-off-by: Qin Wei <support@vocore.io> [added missing commit message, and fixed author with SoB from PR message] Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Speed up eeprom read/writeAdrian Schmutzler2019-03-211-2/+2
| | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
* ramips: Xiaomi MIR3G: detect board name from DTSOzgur Can Leonard2019-03-216-32/+30
| | | | | | | | | | | | | | | | - Former "mir3g" board name becomes "xiaomi,mir3g". - Reorder some entries to maintain alphabetical order. - Change DTS so status LEDs (yellow/red/blue) mimic Xiaomi stock firmware: (Section Indicator) <http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf> <http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf> |Yellow: Update (LED flickering), the launch of the system (steady light); |Blue: during normal operation (steady light); |Red: Safe mode (display flicker), system failure (steady light); Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> [Added link to similar Router 3 model] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-214-3/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add #pwm-cells property to MT76x8 dtsMicke Prag2019-03-181-0/+1
| | | | | | | To be able to configure pwms the pwm driver needs to know the number off cells in the "pwms" property. For this platform this is 2. Signed-off-by: Micke Prag <micke.prag@telldus.se>
* kernel: bump 4.14 to 4.14.106Koen Vandeputte2019-03-181-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: HC5861 drop unused gpio group define in dtsChen Minqiang2019-03-131-7/+0
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for Xiaomi Mi Router 3 ProOzgur Can Leonard2019-03-135-2/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: CPU: MediaTek MT7621AT (2x880MHz) RAM: 512MB DDR3 FLASH: 256MB NAND WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!) WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!) USB: 1x 3.0 ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000 LED: Power/Status BTN: RESET UART: 115200 8n1 Partition layout and boot: Stock Xiaomi firmware has the MTD split into (among others) - kernel0 (@0x200000) - kernel1 (@0x600000) - rootfs0 - rootfs1 - overlay (ubi) Xiaomi uboot expects to find kernels at 0x200000 & 0x600000 referred to as system 1 & system 2 respectively. a kernel is considered suitable for handing control over if its linux magic number exists & uImage CRC are correct. If either of those conditions fail, a matching sys'n'_fail flag is set in uboot env & a restart performed in the hope that the alternate kernel is okay. If neither kernel checksums ok and both are marked failed, system 2 is booted anyway. Note uboot's tftp flash install writes the transferred image to both kernel partitions. Installation: Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in kernel0 for ease of recovery, and install OpenWRT into kernel1 and after. The installation file for OpenWRT is a *squashfs-factory.bin file that contains the kernel and a ubi partition. This is flashed as follows: nvram set flag_try_sys1_failed=1 nvram set flag_try_sys2_failed=0 nvram commit dd if=factory.bin bs=1M count=4 | mtd write - kernel1 dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0 reboot Reverting to stock: The part of stock firmware we've kept in kernel0 allows us to run stock recovery, which will re-flash stock firmware from a *.bin file on a USB. For this we do the following: fw_setenv flag_try_sys1_failed 0 fw_setenv flag_try_sys2_failed 1 reboot After reboot the LED status light will blink red, at which point pressing the 'reset' button will cause stock firmware to be installed from USB. Issues: OpenWRT currently does not have support for the MT7615 wifi chips. There is ongoing work to add mt7615 support to the open source mt76 driver. Until that support is in place, there are closed-source kernel modules that can be used. See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170 Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [02_network remaps, Added link to notes]
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-114-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: rework network settings for HC5861Chen Minqiang2019-03-062-18/+14
| | | | | | | dts: disable port4 and leave it ephy mode because it connect to nothing switch port5 connected to GE port we use it as wan port Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: export chip version and pkgDaniel Golle2019-03-061-0/+19
| | | | | | | | | | | Similar to the (currently unused) mt7620_get_eco() function, introduce mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to probe for the type of WiSoC. This is ugly and probably unacceptable for upstream, however, it should help to evaluate which of those hacks are actually really needed, enumerate the possible values and label them in a more meaningful way than currently done in the vendor driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Belkin F9K1109v1Kip Porterfield2019-03-025-0/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz - RAM: 64Mb - Flash: 8MB (SPI-NOR) - Ethernet: 10/100/1000 Mbps - WLAN Wireless 1: SoC-integrated : 2.4/5 GHz Wireless 2: 2.4 GHz RT3092L - LED: 2x USB, WAN, LAN - Key: WPS, reset - Serial: 4-pin header, (57600,8,N,1), 3.3V TTL, GND, RX, TX, V - J12 marking on board - USB ports: 2 x USB 2.0 Flashing instructions: Option 1 (from bootloader web) - Hold reset button on the back of router when plugging in power (for at-least 10 seconds after plugged in) - Connect to a Lan port - Set computer IP to 10.10.10.3 - Go to http://10.10.10.123 in a web browser - Click the Browse... Button and select the *squashfs.sysupgrade.bin file then click APPLY Option 2 (from the stock admin web) - Go to firmware upgrade - Upload the **factory** image *initramfs.bin first - Boot into openwrt - From Luci web in openwrt upload the *squashfs.sysupgrade.bin Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added v1 to the compatible identifier, added pciid for the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi to prepare for a possible F9K1103 patch]
* ramips: add TP-Link TL-WR802N-v4 supportMarcel Jost2019-02-283-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N-v4. https://openwrt.org/toh/tp-link/tl-wr802n Specification: - MT7628N (580 MHz) - 64 MB RAM - 8 MB FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet - 1x LED Flash instruction: The only way to flash the image in TL-WR802N v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 10 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Marcel Jost <majo@icutech.ch>
* ramips: use generic board detection for Wavlink WL-WN575A3Thomas Vincent-Cross2019-02-284-17/+15
| | | | | | Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices. Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: various Wavlink WL-WN575A3 fixesThomas Vincent-Cross2019-02-281-4/+3
| | | | | | | | | * assign pinmux groups to gpio function for LEDs/buttons * rename flash node to be more generic in line with other device nodes * remove useless/incorrect eeprom property from wmac node * correct base mac address for embedded switch Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: change status LED for Buffalo WHR-G300NINAGAKI Hiroshi2019-02-141-6/+5
| | | | | | | | | | | Buffalo WHR-G300N has a LED for power status indication, but it is not connected to the GPIO and cannot be controlled by the kernel. So, WHR-G300N uses "ROUTER" LED as the system status LED instead. This commit changes it to use "DIAG" LED insted of "ROUTER" like WHR-G301N in ath79 target. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: various Netgear R6120 fixesDavid Bauer2019-02-143-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls the WAN LED. Renames the LED accordingly in the device-tree. Removes the 5GHz WLAN LED trigger. Adds the correct WAN port LED trigger. ---- Currently, the MAC address for the Netgear R6120 is read from the NVRAM partition. The offset for the MAC address however is not consistent across devices or firmware versions. Switch to using the factory partition like all other Netgear devices do. ---- The LAN ports of the R6120 are labled in reverse on the casing. Adjust LuCI switchport numbering accordingly. ---- The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset is bigger than the partition itself). Fixes poor performance on 2.4 and 5 GHz. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-144-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-143-3/+3
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: drop m25p,chunked-io from dtsChuanhong Guo2019-02-0562-62/+0
| | | | | | | | This option was a spi nor hack which is dropped in commit bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead") Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
* ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVBDeng Qingfang2019-02-052-0/+9
| | | | | | This enables MT7610E of the EVB Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add kmod-mt76x2 to WeVo 11AC NASJu Se Hoon2019-02-051-1/+1
| | | | | | | | The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB. Signed-off-by: Ju Se Hoon <joosahoon@gmail.com> [renamed author from Albis-dev to real name, editted commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: dts: Unify naming of gpio-led nodesPetr Štetiar2019-02-05243-243/+243
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* ramips: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-02-05241-241/+241
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* kernel: bump 4.14 to 4.14.97Koen Vandeputte2019-02-011-1/+1
| | | | | | | | | | | | Refreshed all patches. Adapted patches: - 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: rb750gr3: License DTS as GPL-2.0-or-later OR MITAnton Arapov2019-02-011-0/+1
| | | | | | | | | | | | | Adding license in order to fully satisfy dts checklist: - https://openwrt.org/submitting-patches#dts_checklist Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Thibaut <hacks@slashdirt.org> Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Chuanhong Guo <gch981213@gmail.com> Acked-by: Andrew Yong <me@ndoo.sg> Acked-by: Alex Maclean <monkeh@monkeh.net>
* ramips: fix D-Link DIR-615 H1 switch port mappingMirko Parthey2019-01-301-0/+1
| | | | | | | Reuse a device-specific switch port mapping which also applies to the D-Link DIR-615 H1. Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
* ramips: move wifi related interrupts off the main core on SMP systemsFelix Fietkau2019-01-291-0/+31
| | | | | | Improves LAN<->WLAN bridging/routing performance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.14 to 4.14.96Koen Vandeputte2019-01-282-2/+2
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed patches: - 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: Fix kmod-regmap splitHauke Mehrtens2019-01-271-1/+1
| | | | | | | | Two regmap dependencies were wrong, this patch fixes them. This was detected by the build bots. Fixes: fd5c16870169 ("kernel: Build: Split kmod-regmap") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Build: Split kmod-regmapHauke Mehrtens2019-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | This reduces the needed modifications to the mainline Linux kernel and also makes the regmap package work with an out of tree kernel which does not have these modifications. The regmap-core is only added when it is really build as a module. The regmap-core is normally bool so it cannot be built as a module in an unmodified kernel. When it is selected by on other kernel module it will always be selected as build in and it also does not show up in $(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module. When it is not in $(LINUX_DIR)/modules.builtin the build system expects it to be built as a .ko file. Just check if the module is really there and only add it in that case. This splits the regmap package into multiple packages, one for each bus type. This way only the bus maps which are really needed have to be added. This also splits the I2C, SPI and MMIO regmap into separate packages to not require all these subsystems to build them, on an unmodified upstream kernel this also causes problems in some situations. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 11:27:36 +0000