aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt76x8
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for OrayBox X1Bin We2023-04-022-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N. Specifications: SoC: MediaTek MT7628N (580MHz) RAM: 64 MiB Flash: 16 MiB NOR (Winbond W25Q128JVSIQ) Wireless: 802.11b/g/n 2x2 2.4GHz (Built In) Ethernet: 1x 100Mbps only USB: 1x USB Type-A 2.0 Host Port Button: 1x "Reset" button LED: 1x Blue LED + 1x Red LED + 1x White LED Power: 5V Micro-USB input Manufacturer Page: https://pgy.oray.com/router/x1.html/parameter Flash Layout: 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "kpanic" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000fe0000 : "firmware" 0x000000fe0000-0x000000ff0000 : "bdinfo" 0x000000ff0000-0x000001000000 : "reserve" Install via SSH: Original firmware is based on OpenWRT, but SSH is not start by default, You should enable it first 1. Login into web admin (10.168.1.1), default password is 'admin' 2. Open the following link, and the result should be {"code":0}; SSH is now started, username is root, password is same as web admin password http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1 4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware Signed-off-by: Bin We <me@udp.pw>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-041-1/+1
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: improve support for Zyxel Keenetic Extra IIMaxim Anisimov2023-01-281-3/+3
| | | | | | | | | | | - drop unneeded default-state for led_power - concat firmware partitions to extend available free space - increase spi flash frequency to 32 Mhz (value from stock firmware bootlog) - drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support - add compatible for pcie wifi according to kernel documetation - switch to wan mac address with offset 0x28 in rf-eeprom Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for Keenetic KN-1613Maxim Anisimov2023-01-062-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN. Specification: - System-On-Chip: MT7628AN - CPU/Speed: 580 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 4x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn - Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac - 4x LED, 2x button, 1x mode switch Notes: - The device supports dual boot mode - The firmware partitions were concatinated into one - The FN button led indicator has been reassigned as the 2.4GHz wifi indicator. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin" to "KN-1613_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: enable mtd virtual concat support for mt76x8 subtargetMaxim Anisimov2023-01-062-0/+2
| | | | | | This is required for upcoming Keenetic KN-1613 support Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* kernel: Move CONFIG_PWM_IMG and CONFIG_PWM_MEDIATEK to generic configurationHauke Mehrtens2022-12-231-1/+0
| | | | | | | In the build of the ramips/mt76x8 target the user gets asked about these two configuration options, add them to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for Linksys E5400 and clonesJulien Dusser2022-12-181-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350 with the same hardware, but software speed limitations in vendor firmwares. Specification: * SoC: MT7628AN (580 MHz) * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * UART: * 115200, 8N1, 3.3V (real u-boot speed: 119050) * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND) Flash Layout: 0x0000000-0x0030000 : "Bootloader" 0x0030000-0x0040000 : "Config" 0x0040000-0x0050000 : "Factory" 0x0050000-0x0ff0000 : "Kernel" 0x0ff0000-0x1000000 : "CBTinfo" MAC address: LAN: factory 0x28 WAN: LAN + 1 2.4G: LAN + 2 5G: LAN + 3 Installation: 1. Connect to UART, use LF as EOL (not CRLF) 2. Set IP address - Press 4 during boot - setenv serverip <TFTPSERVER_IP> - setenv ipaddr <DEVICE_IP> - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin - saveenv - reset 3. Load Openwrt Kernel image from TFTP: - Press 1 during boot - IP and filename should be already set 4. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Julien Dusser <julien.dusser@free.fr>
* ramips: add support for HiWiFi HC5611Senis John2022-12-043-0/+6
| | | | | | | | | | | | | | | | | | | | | | | CPU: MediaTek MT7628AN @ 575 MHz Flash: 16 MB RAM: 128 MB Ethernet: 10/100Mbps x 1 Wlan: 300 Mbps USB: USB 2.0 x 1 LED: red/green x 1 Button: reset x 1 1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh 2. Upload the openwrt firmware to the router via SCP 3. Login the router via SSH 4. Run `mtd -r write path_to_firmware.bin firmware` I have tested on my device. - The LED will display RED on power-on, After system start completed, trun GREEN - Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device - USB can working under official u-boot Signed-off-by: Senis John <thank243@gmail.com>
* ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4CShiji Yang2022-10-231-0/+7
| | | | | | The blue WAN LED connected to GPIO37 is missing, so re-add it. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic configAleksander Jan Bajkowski2022-10-212-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should be enabled on target or subtarget based on SoC architecture. Fixes warning: $ make kernel_oldconfig CONFIG_TARGET=subtarget ... .config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state .... Summary: - ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture. If it is disabled then the processor operates in LITTLE_ENDIAN mode (default), - ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This option should be enabled after OpenWRT moves to kernel 6.x. After refreshing the kernel, the symbol disappears, - ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN, - MIPS - enabled relevant symbols, - POWERPC - enabled CONFIG_CPU_BIG_ENDIAN, - UML - Symbols are not defined for this architecture, - X86 - always little endian. Symbols are not defined for this architecture. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ramips: kndrt31r19: set up wan interface by defaultAndrey Butirsky2022-10-191-1/+7
| | | | | | The only WAN port of the device is it's modem, so set it up as such Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-192-0/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: 5.15: add disabled PINCTRL_AW9523Sungbo Eo2022-09-181-0/+1
| | | | | | | | | | | | | | Otherwise kernel 5.15 will fail to build on subtargets except for mt7621 that has enabled the config. The disabled PINCTRL_AW9523 config disappears after a refresh, it needs to be added back manually. Fixes: 675cf7557829 ("ramips: add config-5.15 for mt7620 subtarget") Fixes: 001176994a58 ("ramips: add config-5.15 for mt76x8 subtarget") Fixes: b9d9f33c330e ("ramips: add config-5.15 for rt288x subtarget") Fixes: 0164dc0c2563 ("ramips: add config-5.15 for rt305x subtarget") Fixes: ef59da866982 ("ramips: add config-5.15 for rt3883 subtarget") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add config-5.15 for mt76x8 subtargetDaniel Golle2022-09-111-0/+193
| | | | | | | Add Kernel config for testing Linux 5.15 for the mt76x8 subtarget. Compile tested only. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Kroks Rt-Cse SIM Injector DSAndrey Butirsky2022-09-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: add support for Kroks Rt-Pot mXw DS RSIM routerAndrey Butirsky2022-09-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* kernel: Activate CONFIG_GPIOLIB in generic configurationHauke Mehrtens2022-08-101-1/+0
| | | | | | | | All targets expect the malta target already activate the CONFIG_GPIOLIB option. Move it to generic kernel configuration and also activate it for malta. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-07-031-1/+3
| | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com>
* ramips: Add suport for COMFAST CF-WR617ACSergei Iudin2022-07-031-0/+8
| | | | | | | | | | | | | | | | | Specifications: Chipset:MT7628DA+MT7612E Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps Output Power :100mW(20dbm) Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port Flash: 8Mb DRam: 64Mb Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1 Known issues: mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition. Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-241-0/+2
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-161-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: fix wifi mac address of HiWiFi series devicesShiji Yang2022-03-261-0/+22
| | | | | | | | | | | | | | | | | | For HiWiFi series devices, label_mac can be read from bdinfo partition, and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's label_mac start with D4:EE) For example: label D4:EE:07:32:84:88 lan D4:EE:07:32:84:88 wan D4:EE:07:32:84:89 wlan2g D4:EE:07:32:84:88 wlan5g D0:EE:07:32:84:88 Tested on HiWiFi HC5661. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Asus RT-AC1200Ray Wang2022-03-091-26/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: switch parser of trx for mt76x8 subtargetINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | | | | This patch enable parser_trx and disable mtdsplit_trx for mt76x8 subtarget. The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget and the parser need to be switched to parser_trx to use the custom magic number in the header for WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update MAC address configuration for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-2/+2
| | | | | | | | This patch converts MAC address configuration of Buffalo WCR-1166DS in 02_network to use the generic function of OpenWrt. And also, add label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: correct vendor name for COMFAST/JoowinRodrigo Araujo2022-01-221-7/+7
| | | | | | | | | | | | | | | | When Joowin WR758AC V1 and V2 devices were added, they should have been added with the primary manufacturer name which is COMFAST, since Joowin is just an alternate vendor name on some coutries or stores. Fix this by changing the the vendor name on the respective files and set Joowin as ALT0 variants while ensuring compatibility for early users. Also adjust the model names to better follow the naming rules. As a side effect, fix mt76x8 network script which was left incorrectly unsorted on the case block conditions. Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2") Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: add support for Joowin WR758AC V1 and V2Rodrigo Araujo2022-01-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2 devices. Both have the same wall AP/repeater form factor and differ only in the 5Ghz chipset (V1 has MT7662, V2 has MT7663). OpenWrt developers forum page: https://forum.openwrt.org/t/87355 Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB DDR2 - 2.4 GHz: 802.11b/g/n (MT7603) - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663) - Antennas: 4x external single band antennas - LAN: 1x 10/100M - LED: Wifi 3x blue. Programmable - Button: WPS MAC addresses as verified by OEM firmware: use address source LAN *:83 factory 0xe000 2g *:85 factory 0x4 5g *:86 factory 0x8004 How to install: 1- Setup a TFTP server on a machine with IP address 192.168.1.10/24 2- Name the image as `firmware_auto.bin` and place it on the root of the TFTP server 3- Connect the device via Ethernet, it should pick and flash the image Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-171-1/+0
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: remove Linux 5.4 supportRui Salvaterra2021-12-151-192/+0
| | | | | | We're at 5.10 stable, this can finally go. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: mt76x8: tidy up 02_networkSungbo Eo2021-12-121-8/+5
| | | | | | | * fix alphabetic sorting * consolidate duplicate cases Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix tl-mr3020-v3 switch topology to configure vlans via luciSergey V. Lobanov2021-12-041-1/+4
| | | | | | | | | | Currently it is not possible to configure VLANs via LUCI on tplink tl-mr3020-v3. This patch fixes switch topology for the LUCI interface. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in> [copied commit message from github PR] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Wavlink WL-WN576A2Thomas Aldrian2021-11-202-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles repeater / router. It is also sold under the name SilverCrest SWV 733 B1. Device specs: - CPU: MediaTek MT7628AN - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - 5 GHz: a/n/ac MT7610EN - Buttons: WPS, reset, sliding switch (ap/repeater) - LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS Flashing: U-Boot launches a TFTP client if WPS button is held during boot. - Server IP: 192.168.10.100 - Firmware file name: firmware.bin Device will reboot automatically. First boot takes about 90s. Coelner (waenger@gmail.com) is the original author, but I have made some fixes. He does not wish to sign off using his real name. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* ramips: add support for Xiaomi MiWifi 3CEduardo Santos2021-10-311-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE305 v3Michal Kozuch2021-10-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specs (same as in v1): - MT7628AN (575 MHz) - 64MB RAM - 8MB of flash (SPI NOR) - 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan) - 1x 2.4GHz wifi (MT7628AN) - 1x 5Ghz wifi (MT7612E) - 4x LEDs (5 GPIO-controlled) - 1x reset button - 1x WPS button The only and important difference between v1 & v3 is in flash memory layout, so pls don't interchange these 2 builds! Installation through web-ui (on OEM factory firmware): 1. Visit http://tplinkrepeater.net or the configured IP address of your RE305 v3 (default 192.168.0.254). 2. Log in with the password you've set during initial setup of the RE305 (there is no default password). 3. Go to Settings -> System Tools -> Firmware upgrade 4. Click Browse and select the OpenWRT image with factory.bin suffix (not sysupgrade.bin) 5. A window with a progress bar will appear. Wait until it completes. 6. The RE305 will reboot into OpenWRT and serve DHCP requests on the ethernet port. 7. Connect an RJ45 cable from the RE305 to your computer and access LuCI at http://192.168.1.1/ to configure (or use ssh). Disassembly: Just unscrew 4 screws in the corners & take off the back cover. Serial is exposed to the right side of the main board (in the middle) and marked with TX/RX/3V3/GND, but the holes are filled with solder. Installation through serial: 1. connect trough serial (1n8, baudrate=57600) 2. setup the TFTP server and connect it via ethernet (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc) 3. boot from a initramfs image first (choose 1 in the bootloader options) 4. test it a bit with that, then proceed to run sysupgrade build MAC addresses as verified by OEM firmware: use OpenWrt address reference LAN eth0 *:d2 label 2g wlan0 *:d1 label - 1 5g wlan1 *:d0 label - 2 The label MAC address can be found in config 0x2008. Signed-off-by: Michal Kozuch <servitkar@gmail.com> [redistribute WLAN node properties between DTS/DTSI, remove compatible on DTSI, fix indent/wrapping, split out firmware-utils change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: minew g1-c: use default static address for lan instead of dhcpAlexander Couzens2021-08-311-5/+1
| | | | | | | | | As Adrian Schmutzler suggested on github [1] the device should follow the default behaviour on ethernet using a static address instead using dhcp. [1] https://github.com/openwrt/openwrt/commit/8d497b65704f62294a4bbc0e1f5aa4eb1dbf9e24 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for D-Link DAP-1325-A1Giovanni Cascione2021-08-252-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300) Specifications: - SoC: 580Mhz MT7628NN - RAM: 64MB, DDR2 SDRAM - Storage: 8MB, SPI (W25Q64JVSSIQ) - Ethernet: 1x 10/100 LAN port - WIFI: 2.4 GHz 802.11bgn - LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x) - Buttons: Reset, WPS - UART: Serial console (57600, 8n1) Row of 4 holes near LAN port, starting from square hole: 3.3V, TX,RX,GND - FCC ID: fccid.io/KA2AP1325A1/ Installation: Failsafe UI Firmware can be uploaded with Failsafe UI web page: - turn device off - press and hold reset button - turn device on - keep holding reset until red wifi strength led turns on (ab. 10sec) - connect to device through LAN port PC must be configured with static ip (192.168.0.x) - connect to 192.168.0.50 - select image to be flashed and upload. Device will reboot after successful update Serial port/TFTP server - Connect through serial connectors on PCB (e.g. with teraterm) - Set up a TFTP server, and connect through LAN with static IP - Put image file in the root of the server - Boot the device and select '2' at U-Boot startup - Set device IP, server IP and image file name - Start upload and flash Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com> [fix whitespaces in DTS, convert to nvmem, add mtd-eeprom] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Motorola MWR03Shiji Yang2021-08-251-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7628AN + MT7612E * ROM: 8 MiB Flash * RAM: 64 MiB DDR2 * WAN: 10/100M *1 * LAN: 10/100M *3 * Button: Reset *1 * LEDs: orange *1, white *1 * Antennas: 2.4 GHz *2 + 5 GHz *2 * TTL Baudrate: 57600 * TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100 MAC addresses as verified by OEM firmware: use address source 2g *:d8 factory 0x0004 (label) 5g *:d9 factory 0x8004 LAN *:d7 factory $label -1 WAN *:da factory $label +2 Installation (TFTP + U-Boot): * Connect device with a TTL cable and open a serial session by PuTTY. * Press "2" when booting to select "Load system code then write to Flash via TFTP". * Configure the IP of local host server. * Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix DTS line endings, fix label MAC address, adjust status LED names, convert mtd-mac-address-increment to mac-address-increment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Onion Omega 2(+)Adrian Schmutzler2021-08-211-4/+6
| | | | | | | | | | Thanks to a hint from Michael Siegenthaler in 4b4fa2f9fed7 ("ramips: fix ethernet MAC address on Omega2"), the label MAC address of the Onion Omega 2(+) can be set based on its documentation [1]. [1] https://docs.onion.io/omega2-docs/mac-address.html Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: add various missing config symbolsDavid Bauer2021-08-102-0/+2
| | | | | | Fixes commit 91a52f22a13d ("treewide: backport support for nvmem on non platform devices") Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix missing NVMEM subsystemDavid Bauer2021-07-212-0/+2
| | | | | | | | | | | | MAC address retrieval was switched to more generic upstream (5.13) NVMEM based solution in commit 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") , but NVMEM subsystem wasn't enabled in the kernel, so fix it now. References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801 Fixes: 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
* ramips: add support for minew g1-cAlexander Couzens2021-07-051-0/+5
| | | | | | | | | | | | | | | | | | | | | | The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add AW9523 I2C GPIO expander driverDavid Bauer2021-06-272-0/+2
| | | | | | | | | | | | | | This adds a driver for the AW9523 I2C GPIO expander. This driver is required to make LEDs as well as buttons on the Tenbay T-MB5EU-V01 work. This driver already had several upstream iterations. I'm working to push this driver to mainline. Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287 Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix Ethernet random MAC address for HILINK HLK-7628NLiu Yu2021-06-091-4/+1
| | | | | | | | | | | | | | | | | | Set the ethernet address from flash. MAC addresses as verified by OEM firmware: use interface source 2g wlan0 factory 0x04 (label) LAN eth0.1 factory 0x28 (label+1) WAN eth0.2 factory 0x2e (label+2) Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N") Signed-off-by: Liu Yu <f78fk@live.com> [drop old MAC address setup from 02_network, cut out state_default changes, face-lift commit message, add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Wavlink WL-WN578A2Thomas Aldrian2021-05-282-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-212-4/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: 5.10: refresh configsIlya Lipnitskiy2021-03-061-4/+4
| | | | | | | | Run-tested on Ubiquiti EdgeRouter X. Compile tested on all other subtargets. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: copy config-5.4 to config-5.10Ilya Lipnitskiy2021-03-061-0/+191
| | | | | | Strict copy, no changes made. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* Revert "ramips: add support for kernel 5.10"Adrian Schmutzler2021-03-061-191/+0
| | | | | | | | | This reverts commit b4aad29a1d7ad77d67073c1c54b28c429c64ed9b. This was accidentally folded into a single commit. Remove it and apply it properly again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-13 16:18:31 +0000