| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | ramips: support dual image feature on ALFA Network boards | Piotr Dymacz | 2019-11-13 | 2 | -0/+19 |
| | | | | | | | | | | | | | | | | | | | | | | | | | | New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards includes support for a 'dual image' feature. Users can enable it using U-Boot environment variable 'dual_image' ('1' -> enabled). When 'dual image' feature is enabled, U-Boot will modify DTB and divide the original 'firmware' flash area into two, equal in size and aligned to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust size of 'firmware' area to match installed flash chip size. U-Boot will load kernel from active partition which is marked with env variable 'bootactive' ('1' -> first partition, '2' -> second partition) and rename both partitions accordingly ('firmware' <-> 'backup'). There are 3 additional env variables used to control 'dual image' mode: - bootlimit - maximum number of unsuccessful boot tries (default: '3') - bootcount - current number of boot tries - bootchanged - flag which informs that active partition was changed; if it is set and 'bootcount' reaches 'bootlimit' value, U-Boot will start web-based recovery which then updates both partitions with provided image Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> | ||||
| * | ramips: read label MAC address from flash instead of using phy0/phy1 | Adrian Schmutzler | 2019-11-13 | 1 | -2/+2 |
| | | | | | | | | | This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress) by retrieval from the proper flash locations. This will make 02_network independent of WiFi setup again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | ||||
| * | ramips: split further base-files across subtargets | Adrian Schmutzler | 2019-11-11 | 2 | -0/+33 |
| | | | | | | | | | | | | As started in 19724e28c81e ("ramips: split base-files into subtargets"), this moves some smaller left-over files to the appropriate base-files folder of their subtarget: - /etc/init.d/bootcount - /etc/uci-defaults/04_led_migration Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | ||||
| * | ramips: remove default case for MAC address assignment | Adrian Schmutzler | 2019-11-06 | 1 | -5/+24 |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, MAC address assignment in ramips has contained a default case, which defined wan_mac = eth0 + 1 for _every_ device not having an explicit case there. This is not desirable, as many device supporters will just not care or know about this definition, so another MAC address will be introduced by accident. In some cases the wan_mac is assigned although it is not needed, in other cases even addresses not dedicated to the device will be used (e.g. wan_mac actually is eth0 - 1, but during support nobody cared, so eth0 + 1 is used now, which might actually belong to another device ...). Thus, in this PR the former default case is converted to an explicit case. This one comprises all devices not being accounted for by other cases, reduced by those not having wan at all. The big number of entries for this node might be another indication that many of them wouldn't actually be there if there hadn't been default wan_mac setup. In exchange, the current "do nothing" case can be removed, as it will be the new default case. The devices being put in the newly created explicit case were determined as follows: 1. Create a list of all devices based on the DTS files. 2. Remove all devices already having an explicit entry setting their address. 3. Remove all devices that only have lan set up in the first part of 02_network: mt7620: - alfa-network,tube-e4g - asus,rp-n53 - buffalo,wmr-300 - comfast,cf-wr800n - edimax,ew-7476rpc - edimax,ew-7478ac - elecom,wrh-300cr - hnet,c108 - kimax,u25awf-h1 - kimax,u35wf - kingston,mlw221 - kingston,mlwg2 - microduino,microwrt - netgear,ex2700 - netgear,ex3700 - netgear,wn3000rp-v3 - planex,cs-qr10 - planex,mzk-ex300np - planex,mzk-ex750np - ravpower,wd03 - sercomm,na930 - yukai,bocco - zbtlink,zbt-cpe102 - zte,q7 mt7621: - gnubee,gb-pc1 - gnubee,gb-pc2 - linksys,re6500 - mikrotik,rbm11g - netgear,ex6150 - thunder,timecloud - tplink,re350-v1 - tplink,re650-v1 mt76x8: - alfa-network,awusfree1 - d-team,pbr-d1 - glinet,vixmini - vocore,vocore2-lite - tama,w06 - tplink,tl-mr3020-v3 - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 - vocore,vocore2 - widora,neo-16m - widora,neo-32m rt288x: - buffalo,wli-tx4-ag300n - dlink,dap-1522-a1 rt305x: - allnet,all0256n-4m - allnet,all0256n-8m - allnet,all5002 - allnet,all5003 - alphanetworks,asl26555-16m - alphanetworks,asl26555-8m - asus,wl-330n - aximcom,mr-102n - dlink,dcs-930 - easyacc,wizard-8800 - hame,mpr-a2 - hootoo,ht-tm02 - huawei,d105 - intenso,memory2move - planex,mzk-dp150n - rt305x dlink,dcs-930l-b1 - sparklan,wcr-150gn - tenda,3g150b - tenda,3g300m - tenda,w150m - trendnet,tew-638apb-v2 - unbranded,a5-v11 - vocore,vocore-16m - vocore,vocore-8m - wansview,ncs601w - zorlik,zl5900v2 rt3883: - loewe,wmdr-143n - omnima,hpm 4. Put the remaining devices in the new case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | ||||
| * | ramips: split base-files into subtargets | Adrian Schmutzler | 2019-11-03 | 3 | -0/+353 |
| While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space. In certain cases, keeping files in parent (=target) base-files was more convenient, and thus no splitting was performed for those. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (mt7621) 60958 B split (mt7620) 46358 B (- 14.3 kiB) split (mt7621) 48759 B (- 11.9 kiB) split (mt76x8) 44948 B (- 15.6 kiB) split (rt288x) 43508 B (- 17.0 kiB) split (rt305x) 45616 B (- 15.0 kiB) split (rt3883) 44176 B (- 16.4 kiB) Run-tested on: GL.iNet GL-MT300N-V2 (mt76x8) D-Link DWR-116 (mt7620) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | |||||
 |
index : openwrt/upstream | |
| upstream openwrt | James |
| aboutsummaryrefslogtreecommitdiffstats |