aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for Netgear WAX202Wenli Looi2022-07-214-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0f068e7c4a83bcbf20c4e52a5f8a3f1fe2af2246)
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-271-0/+2
| | | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 539e60539a2fde6531bd179c94bb9c7f8f490f2b)
* ramips: force ZyXEL NR7101 to boot from "Kernel" partitionBjørn Mork2022-06-251-0/+1
| | | | | | | | | | | | | | | | | | | | Make sure BootingFlag points to the system partition we install to. The BootingFlag variable selects which system partition the system boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have device specific support for this dual image scheme, and can therefore only boot from "Kernel". This has not been an issue until now, since all known OEM firmware versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0. But the newest OEM firmware has a new upgrade procedure, installing to the "inactive" system partition and setting BootingFlag accordingly. This workaround is needed until the dual image scheme is fully supported. Signed-off-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 79112e7d4758cc79dea506ffebdf40e00d94fa06)
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-061-0/+4
| | | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> (cherry picked from commit ce90ba1f3168e3f4581fd8581e2c0cd31efa14cf)
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-171-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4a8eaa5c7c9235212c4af022c18b2dfbadfe557f)
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-172-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 9ee6ac00c43cc253ac554495edb6214563ab1f31)
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-05-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit 32e6942d72b6426d65eaa4dc7f2ba949b3c32985)
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-05-172-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com> (cherry picked from commit 39799974a372fb4333d21f077c670b8a56b9d696)
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-05-172-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea)
* ramips: add support for OrayBox X3ARay Wang2022-04-193-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com> (cherry picked from commit 9a750aae62de74b488d7df7bdbfa78cd606a8aaf)
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-191-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-194-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: update WLAN MAC address of JCG Y2Chukun Pan2022-03-131-0/+4
| | | | | | | | MAC addresses on OEM firmware: 04:xx:xx:xx:xx:c8 factory 0x4 wlan2g 06:xx:xx:xx:xx:c8 [not on flash] wlan5g Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: update WLAN MAC address of Phicomm K2PChukun Pan2022-03-131-1/+2
| | | | | | | The wireless mac address difference of this machine is similar to that of D-Link DIR-853-R1, so use the same practice. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: mt7621: add support for Zbtlink ZBT-WG1608Kim Namu2022-03-091-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim Namu <namu@theseed.io>
* ramips: add support for Renkforce WS-WN530HP3-ABirger Koblitz2022-03-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Renkforce WS-WN530HP3-A ceiling- mountable Wireless Access Point, which is powered over PoE. Hardware: - SoC: Mediatek MT7621DAT - RAM: 128MiB on SoC - Flash: 16MiB GigaDevice GD25Q128C - 2.4Ghz Wifi: Mediatek MT603EN - 5GHz Wifi: MT613BEN - Ethernet: - 1x 1GBit WAN port, passive PoE capable - 2x 1GBit LAN ports LEDs: 1x Bi-Color LED (red/blue) Buttons: 1x Reset Button, 1x Power Button Installation: Power on the access point and immedately press the reset button for 10 seconds. Connect web-browser to 192.168.10.1 and upload sysupgrade image. Flash uploaded image and wait about 2 minutes for reboot. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
* ramips: Add support for TP-Link TL-WPA8631P v3Joe Mullally2022-03-062-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender Specifications -------------- * SoC: MediaTek MT7621AT * CPU: 880 MHz MIPS 1004KEc dual-core CPU * RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E) * Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG) * Ethernet: SoC built-in Switch 5x 1GbE * Port 0: PLC (connected through AR8035-A) * Port 1-3: LAN * WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN) * PLC: HomePlug AV2 (Qualcomm QCA7500) * PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG) * Buttons: Reset, LED, Pair, Wi-Fi * LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green), 5G (green) * UART: J1 (57600 baud) * Pinout: (3V3) (GND) (RX) (TX) * Visually identify GND from connection to PCB ground plane Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please first check the OpenWRT Wiki page for confirmation that your OEM firmware version is supported. Signed-off-by: Joe Mullally <jwmullally@gmail.com>
* ramips: support TP-Link EAP615-WallStijn Tintel2022-02-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP. The device is very similar to the TP-Link EAP235-Wall. Hardware: * SoC: MediaTek MT7621AT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Ethernet: 4x GbE * Back: ETH0 (PoE-PD) * Bottom: ETH1, ETH2, ETH3 (PoE passthrough) * WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R * LEDS: 1x white * Buttons: 1x LED, 1x reset Stock firmware uses a random MAC address for ethernet. OpenWrt uses the MAC address that is on the device label for ethernet and the wireless interfaces. MAC address must not be incremented, as this will cause MAC address conflicts in case you have two devices with consecutive MAC addresses. Instead, different locally administered addresses will be generated automatically, based on the MAC on the label. Installation via stock firmware: * Enable SSH in the TP-Link web interface * SSH to the device * Run `cliclientd stopcs` * Upload the OpenWrt factory image via the TP-Link web interface Installation via bootloader: * Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1 closest to ETH1. Baud rate 115200 * Interrupt boot process by holding a key during boot * Boot the OpenWrt initramfs: # tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin # bootm * Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin to /tmp and use sysupgrade to install it Thanks to Sander Vanheule for his work on the EAP235-Wall, which made adding support for the EAP615-Wall very easy. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Sander Vanheule <sander@svanheule.net> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for ipTIME A3002MESHYoonji Park2022-02-202-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for ipTIME A3002MESH. Hardware: - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: XMC XM25QH128AHIG (SPI-NOR 16MB) - WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in) - UART: [GND, RX, TX, 3.3V] (57600 8N1, J4) MAC addresses: | interface | MAC | source | comment |-----------|-------------------|----------------|---------- | LAN | 70:XX:XX:5X:XX:X3 | | | WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 | | WLAN 2G | 72:XX:XX:4X:XX:X0 | | | WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4 | | | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown | | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown - WLAN 2G MAC address is not the same as stock firmware since OpenWrt uses LAN MAC address with local bit sets. Installation: 1. Flash initramfs image. This can be done using stock web ui or TFTP 2. Connect to OpenWrt with an SSH connection to 192.168.1.1 3. Perform sysupgrade with sysupgrade image Revert to stock firmware: - Flash stock firmware via OEM TFTP Recovery mode - Perform sysupgrade with stock image TFTP Recovery method: 1. Unplug the router 2. Hold the reset button and plug in 3. Release when the power LED stops flashing and go off 4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0 5. Flash image with TFTP client to 192.168.0.1 Signed-off-by: Yoonji Park <koreapyj@dcmys.kr> [wrap/rephrase commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: update WLAN MAC address of ipTIME A3004TSungbo Eo2022-02-111-0/+6
| | | | | | | | | | | | | | | | Reported MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 90:xx:xx:18:xx:1F | | [1] | WAN | 90:xx:xx:18:xx:1D | | | WLAN 2G | 92:xx:xx:48:xx:1C | | | WLAN 5G | 90:xx:xx:18:xx:1C | factory 0x4 | | | 90:xx:xx:18:xx:1C | config ethaddr | [1] Used in this patch as WLAN 2G MAC address with the local bit set Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-02-112-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:xx:xx:00:xx:9B | | [1] | WAN | 58:xx:xx:00:xx:99 | | | WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 | | WLAN 5G | 5A:xx:xx:40:xx:98 | | | | 58:xx:xx:00:xx:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load addresses: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. The stock web interface will flash only on the inactive boot partition, but the recovery web page will always flash on boot partition 1. Installation via recovery mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-091-0/+1
| | | | | | | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531. Fix some link up/down issues. The errornous check for the PHY mode which broke things with MT7531 has been removed as suggested by patch net: phy: mediatek: remove PHY mode check on MT7531 As a result, things are working fine now on MT7622+MT7531 as well. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for Xiaomi Mi Router CR660x seriesRaymond Wang2022-02-073-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports. Alongside the general model, it has three carrier customized models: CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom) Specifications: - SoC: MediaTek MT7621AT - RAM: 256MB DDR3 (ESMT M15T2G16128A) - Flash: 128MB NAND (ESMT F59L1G81MB) - Ethernet: 1000Base-T x4 (MT7530 SoC) - WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN) - LEDs: System (Blue, Yellow), Internet (Blue, Yellow) - Buttons: Reset, WPS - UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1) - Power: 12VDC, 1A Jailbreak Notes: 1. Get shell access. 1.1. Get yourself a wireless router that runs OpenWrt already. 1.2. On the OpenWrt router: 1.2.1. Access its console. 1.2.2. Create and edit /usr/lib/lua/luci/controller/admin/xqsystem.lua with the following code (exclude backquotes and line no.): ``` 1 module("luci.controller.admin.xqsystem", package.seeall) 2 3 function index() 4 local page = node("api") 5 page.target = firstchild() 6 page.title = ("") 7 page.order = 100 8 page.index = true 9 page = node("api","xqsystem") 10 page.target = firstchild() 11 page.title = ("") 12 page.order = 100 13 page.index = true 14 entry({"api", "xqsystem", "token"}, call("getToken"), (""), 103, 0x08) 15 end 16 17 local LuciHttp = require("luci.http") 18 19 function getToken() 20 local result = {} 21 result["code"] = 0 22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i 's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop bear start;" 23 LuciHttp.write_json(result) 24 end ``` 1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token It should give you a respond like this: {"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."} If so, continue; Otherwise, check the file, reboot the rout- er, try again. 1.2.4. Set wireless network interface's IP to 169.254.31.1, turn off DHCP of wireless interface's zone. 1.2.5. Connect to the router wirelessly, manually set your access device's IP to 169.254.31.3, make sure http://169.254.31.1/cgi-bin/luci/api/xqsystem/token still have a similar result as 1.2.3 shows. 1.3. On the Xiaomi CR660x: 1.3.1. Login to the web interface. Your would be directed to a page with URL like this: http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r- outer 1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME} {PASSWORD} be your OpenWrt router's SSID and password: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy- stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO- RD} It should return 0. 1.3.3. Browse this URL with {STOK} from 1.3.1: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy- stem/oneclick_get_remote_token?username=xxx&password=xxx&- nonce=xxx 1.4. Before rebooting, you can now access your CR660x via SSH. For CR6606, you can calculate your root password by this project: https://github.com/wfjsw/xiaoqiang-root-password, or at https://www.oxygen7.cn/miwifi. The root password for carrier-specific models should be the admi- nistration password or the default login password on the label. It is also feasible to change the root password at the same time by modifying the script from step 1.2.2. You can treat OpenWrt Router however you like from this point as long as you don't mind go through this again if you have to expl- oit it again. If you do have to and left your OpenWrt router unt- ouched, start from 1.3. 2. There's no official binary firmware available, and if you lose the content of your flash, no one except Xiaomi can help you. Dump these partitions in case you need them: "Bootloader" "Nvram" "Bdata" "crash" "crash_log" "firmware" "firmware1" "overlay" "obr" Find the corespond block device from /proc/mtd Read from read-only block device to avoid misoperation. It's recommended to use /tmp/syslogbackup/ as destination, since files would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP Keep an eye on memory usage though. 3. Since UART access is locked ootb, you should get UART access by modify uboot env. Otherwise, your router may become bricked. Excute these in stock firmware shell: a. nvram set boot_wait=on b. nvram set bootdelay=3 c. nvram commit Or in OpenWrt: a. opkg update && opkg install kmod-mtd-rw b. insmod mtd-rw i_want_a_brick=1 c. fw_setenv boot_wait on d. fw_setenv bootdelay 3 e. rmmod mtd-rw Migrate to OpenWrt: 1. Transfer squashfs-firmware.bin to the router. 2. nvram set flag_try_sys1_failed=0 3. nvram set flag_try_sys2_failed=1 4. nvram commit 5. mtd -r write /path/to/image/squashfs-firmware.bin firmware Additional Info: 1. CR660x series routers has a different nand layout compared to other Xiaomi nand devices. 2. This router has a relatively fresh uboot (2018.09) compared to other Xiaomi devices, and it is capable of booting fit image firmware. Unfortunately, no successful attempt of booting OpenWrt fit image were made so far. The cause is still yet to be known. For now, we use legacy image instead. Signed-off-by: Raymond Wang <infiwang@pm.me>
* Revert "kernel: backport MediaTek Ethernet PHY driver"Hauke Mehrtens2022-02-051-1/+0
| | | | | | | | | | | | | | | | | | This reverts commit 8b4cba53a9402f44da2dced4a78ca065b15dca94. This broke the mt7530 on Linksys e8450 (mt7622) for me. [ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL [ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0 [ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL [ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1 [ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL [ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2 [ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL [ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3 [ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL [ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-051-0/+1
| | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530. Fix some link up/down issues. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* Revert "ramips: add support for ipTIME AX2004M"Stijn Tintel2022-02-012-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit f4a79148f8cb ("ramips: add support for ipTIME AX2004M") seems to leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no longer boot. The leak is visible in u-boot: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0x840000e4 Data Size: 10750165 Bytes = 10.3 MiB Architecture: MIPS OS: Linux Load Address: 0x82000000 Entry Point: 0x82000000 Normally, it should look like this: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0xbfca00e4 Data Size: 2652547 Bytes = 2.5 MiB Architecture: MIPS OS: Linux Load Address: 0x80001000 Entry Point: 0x80001000 Revert the commit to avoid more people soft-bricking their devices. This reverts commit f4a79148f8cbb7dfbcddfb0c1128caec45a01596. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-01-292-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specification: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC address: | interface | MAC | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:XX:XX:00:XX:9B | | [1] | WAN | 58:XX:XX:00:XX:99 | | | WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4 | | WLAN 5G | 5A:XX:XX:40:XX:98 | | | | | | | | 58:XX:XX:00:XX:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load address: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation via **recovery** mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: enable I2C_CHARDEV in mt7621/config-5.10Stijn Tintel2022-01-281-0/+1
| | | | | | | | I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the 5.10 config, as it's required for PoE control on Unifi Switch Flex. Fixes: b4aad29a1d7a ("ramips: add support for kernel 5.10") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: update Tenbay T-MB5EU wireless MAC addressDavid Bauer2022-01-221-2/+1
| | | | | | | | | | | | | | The current MAC address assignment is still incorrect. Use the same MAC address as seen on the stock firmware for both wireless interfaces. The 5GHz MAC address OUI is +2 in the first EUI octet. We currently don't do this in OpenWrt. Ignore this offset for now. With the current assignment, recurring MAC addresses between radios is already taken care of. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: enable badblock table support on linksys ea7xxx devicesFelix Fietkau2022-01-131-0/+1
| | | | | | Use remapping only on the kernel partitions. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mikrotik: enable variable size eraseOskari Lemmela2022-01-131-0/+1
| | | | | | | Add support for variable size erase blocks. Enable it to all targets which has mikrotik targets. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* ramips: add support for Linksys EA6350 v4Nick McKinney2022-01-085-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net>
* ramips: add support for RAISECOM MSG1500 X.00Liangkuan Yang2022-01-083-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router. Apart from the general model, there are two ISP customized models: China Mobile and China Telecom. Specifications: - SoC: Mediatek MT7621AT - RAM: 256MiB DDR3 - Flash: 128MiB NAND - Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN - Switch: MediaTek MT7530 (SoC) - WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps) - USB: 1 * USB 2.0 port - Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button - LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB - UART: 1 * serial port header (4-pin) - Power: DC 12V, 1A - Switch: 1 * POWER switch MAC addresses as verified by vendor firmware: use address source LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label) WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii 5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex 2.4G CA:XX:XX:4A:XX:E8 [not on flash] The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30 C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10 C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Notes: 1. The vendor firmware allows you to connect to the router by telnet. (known version 1.0.0 can open telnet.) There is no official binary firmware available. Backup the important partitions data: "Bootloader", "Config", "Factory", and "firmware". Note that with the vendor firmware the memory is detected only 128MiB and the last 512KiB in NAND flash is not used. 2. The POWER LED is default on after press POWER switch. The WAN and LAN1 - 4 LEDs are wired to ethernet switch. The WPS LED is controlled by MT7615DN's GPIO. Currently there is no proper way to configure it. 3. At the time of adding support the wireless config needs to be set up by editing the wireless config file: * Setting the country code is mandatory, otherwise the router loses connectivity at the next reboot. This is mandatory and can be done from luci. After setting the country code the router boots correctly. A reset with the reset button will fix the issue and the user has to reconfigure. * This is minor since the 5g interface does not come up online although it is not set as disabled. 2 options here: 1- Either run the "wifi" command. Can be added from LuCI in system - startup - local startup and just add wifi above "exit 0". 2- Or add the serialize option in the wireless config file as shown below. This one would work and bring both interfaces automatically at every boot: config wifi-device 'radio0' option serialize '1' config wifi-device 'radio1' option serialize '1' Flash instructions using initramfs image: 1. Press POWER switch to power down if the router is running. 2. Connect PC to one of LAN ports, and set static IP address to "10.10.10.2", netmask to "255.255.255.0", and gateway to "10.10.10.1" manually on the PC. 3. Push and hold the WIFI button, and then power up the router. After about 10s (or you can call the recovery page, see "4" below) you can release the WIFI button. There is no clear indication when the router is entering or has entered into "RAISECOM Router Recovery Mode". 4. Call the recovery page for the router at "http://10.10.10.1". Keep an eye on the "WARNING!! tip" of the recovery page. Click "Choose File" to select initramfs image, then click "Upload". 5. If image is uploaded successfully, you will see the page display "Device is upgrading the firmware... %". Keep an eye on the "WARNING!! tip" of the recovery page. When the page display "Upgrade Successfully", you can set IP address as "automatically obtain". 6. After the rebooting (PC should automatically obtain an IP address), open the SSH connection, then download the sysupgrade image to the router and perform sysupgrade with it. Flash back to vendor firmware: See "Flash instructions 1 - 5" above. The only difference is that in step 4 you should select the vendor firmware which you backup. Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
* ramips: add support for ipTIME T5004Sungbo Eo2022-01-022-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A. Specifications: * SoC: MT7621AT * RAM: 128 MiB * Flash: NAND 128 MiB * Ethernet: 5x 1GbE * Switch: SoC built-in * UART: J4 (57600 baud) * Pinout: [3V3] (TXD) (RXD) (GND) Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware via recovery mode: 1. Press reset button, power up the device, wait >15s for CPU LED to stop blinking. 2. Upload stock image to TFTP server at 192.168.0.1. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME A3004TWonJung Kim2021-12-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim <git@won-jung.kim> (added led dt-bindings) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: 5.10: consolidate mac80211 crypto optionsSergey Ryazanov2021-12-171-6/+0
| | | | | | | | | | | | | | | | | | | | | | Each of - CRYPTO_AEAD2 - CRYPTO_AEAD - CRYPTO_GF128MUL - CRYPTO_GHASH - CRYPTO_HASH2 - CRYPTO_HASH - CRYPTO_MANAGER2 - CRYPTO_MANAGER - CRYPTO_NULL2 either directly required for mac80211 crypto support, or directly selected by such options. Support for the mac80211 crypto was enabled in the generic config since c7182123b9 ("kernel: make cryptoapi support needed by mac80211 built-in"). So move the above options from the target configs to the generic config to make it clear why do we need them. CC: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-171-1/+0
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: remove Linux 5.4 supportRui Salvaterra2021-12-151-282/+0
| | | | | | We're at 5.10 stable, this can finally go. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: fix Tenbay T-MB5EU v1 Wireless MACDavid Bauer2021-12-151-0/+5
| | | | | | | | | | | | | It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC address set on 2.4 and 5 GHz. Some boards do not seem to have the correct MAC address set for the external PHY of the MT7915 radio at caldata offset 0xa. As the external PHY does not expose a DT binding (yet), fix up the mac address in userspace. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for HUMAX E10Kyoungkyu Park2021-12-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router, based on MediaTek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 128MB - Flash: SPI NOR 16MB (MXIC MX25L12805D) - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 2x 10/100/1000Mbps - Switch: SoC internal - USB: 1x USB 2.0 Type-A - UART: J1 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation via web interface: - Flash **factory** image through the stock web interface. Recovery procedure: 1. Connect ethernet cable between Router **LAN** port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) - It can accept both images which is HUMAX stock firmware dump (0x70000-0x1000000) image and OpenWRT **sysupgrade** image. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space> [remove trailing whitespace] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Netgear R7450Dale Hui2021-09-262-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Netgear R7450 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [fix model/compatible in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear R6900v2Dale Hui2021-09-262-0/+2
| | | | | | | | | | | | | | | | | | | | | | | Netgear R6900v2 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
* ramips: make Netgear R7200 a separate device from R6700v2Dale Hui2021-09-262-1/+3
| | | | | | | | | With the various variants of Netgear R**** devices, make it more obvious which image should be used for the R7200. Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [provide proper commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable I2C_CHARDEVDavid Bauer2021-09-251-0/+1
| | | | | | | Expose I2C busses with a chardev device. This is required to control the PSE controller on the Ubiquiti UniFi Flex Switch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Ubiquiti USW-FlexDavid Bauer2021-09-251-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7621AT 16M SPI-NOR Macronix MX25L12835FMI Microchip PD69104B1 4-Channel PoE-PSE controller TI TPS2373 PoE-PD controller PoE-Controller -------------- By default, the PoE outputs do not work with OpenWrt. To make them output power, install the "poemgr" package from the packages feed. This package can control the PD69104B1 PSE controller. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt" via SSH. 2. Add the uboot-envtools configuration file /etc/fw_env.config with the following content $ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config 3. Update the bootloader environment. $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 4. Transfer the OpenWrt sysupgrade image to the device using SCP. 5. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 6. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 8. Reboot the device. It should boot into OpenWrt. Restore to UniFi ---------------- To restore the vendor firmware, follow the Ubiquiti UniFi TFTP recovery guide for access points. The process is the same for the Flex switch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-DX2033GRINAGAKI Hiroshi2021-09-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI) - WLAN : 2.4/5 GHz - 2.4 GHz : 2T2R, MediaTek MT7603E - 5 GHz : 4T4R, MediaTek MT7615 - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: 3.3V, TX, RX, NC, GND from triangle mark - 57600n8 - Power : 12 VDC, 1 A Flash instruction using initramfs image: 1. Boot WN-DX2033GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, download the sysupgrade.bin image to the device and perform sysupgrade with it 5. Wait ~120 seconds to complete flashing Notes: - The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and it is certified under the same radio-wave related regulations in Japan - The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" (called as "combo image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB") - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32" - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b) : kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs - There are 2x important flags in the flash: - bootnum : select os partition for booting (persist, 0x4) - 0x01: firmware - 0x02: firmware_2 - debugflag : allow interrupt kernel loader, it's named as "Z-LOADER" (Factory, 0xFE75) - 0x00: disable debug - 0x01: enable debug MAC addresses: LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text)) WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex)) 2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex)) 5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: move two symbols to the generic kconfigsRui Salvaterra2021-08-292-4/+0
| | | | | | | CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them to the generic kconfigs. And resort the generic kconfigs while at it. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: mt7621: remove bring up DSA master init scriptDENG Qingfang2021-07-231-20/+0
| | | | | | | With commit 2e17c710954b, there is no need to bring up DSA master port manually. Signed-off-by: DENG Qingfang <dqfext@gmail.com>
* ramips: fix missing NVMEM subsystemDavid Bauer2021-07-212-0/+2
| | | | | | | | | | | | MAC address retrieval was switched to more generic upstream (5.13) NVMEM based solution in commit 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") , but NVMEM subsystem wasn't enabled in the kernel, so fix it now. References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801 Fixes: 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
* ramips: fix Wifi MAC address setup for D-Link DIR-853 R1Adrian Schmutzler2021-07-121-3/+3
| | | | | | | | Commands in 10_fix_wifi_mac were not properly concatenated, so this was also triggered for the second phy without giving a MAC address as argument. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-06 07:15:11 +0000