aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621/base-files/lib/upgrade
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix device name of netis WF-2881 to WF2881Sungbo Eo2020-02-071-1/+1
| | | | | | | | | | | The correct model name of WF-2881 is WF2881 without hyphen. The former used boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the sysupgrade-tar image, which is newly added in the previous commit, should not be used to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-071-0/+1
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-052-0/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-141-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM, USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support. Specification: - MT7621A (880 MHz) - 256/512 MB of RAM (DDR3) - 16/32+ MB of FLASH (SPI NOR) - optional second SPI flash (8-pin WSON/SOIC) - 1x microSD (SDXC) flash card reader - 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1 - optional 802.3at/af PoE module for WAN - 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V) - 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM) - RTC (TI BQ32002, I2C bus) with backup battery (CR2032) - external hardware watchdog (EM Microelectronic EM6324) - 1x USB 2.0 Type-A - 1x micro USB Type-B for system serial console (Holtek HT42B534) - 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator) - 3x button (reset, user1, user2) - 1x I2C (4-pin, 2.54 mm pitch) header on PCB - 4x SIM (6-pin, 2.00 mm pitch) headers on PCB - 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB - 1x mechanical power switch - 1x DC jack with lock (24 V) Other: - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board has additional logic circuit for M.2 SIM switching. The 'sim-select' will work only if both SIM slots are occupied. Otherwise, always slot with SIM inside is selected, no matter 'sim-select' value. - U-Boot enables power in all three miniPCIe and M.2 slots before loading the kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) - all three miniPCIe slots have additional 5 V supply on pins 47 and 49 - the board allows to install up to two oversized miniPCIe cards (vendor has dedicated MediaTek MT7615N/D cards for this board) - this board has additional logic circuit controlling PERSTn pins inside miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe slots but setting GPIO22 to high allows PERSTn control per slot, using GPIO23-25 (value is inverted) You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: split base-files into subtargetsAdrian Schmutzler2019-11-032-0/+128
While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space. In certain cases, keeping files in parent (=target) base-files was more convenient, and thus no splitting was performed for those. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (mt7621) 60958 B split (mt7620) 46358 B (- 14.3 kiB) split (mt7621) 48759 B (- 11.9 kiB) split (mt76x8) 44948 B (- 15.6 kiB) split (rt288x) 43508 B (- 17.0 kiB) split (rt305x) 45616 B (- 15.0 kiB) split (rt3883) 44176 B (- 16.4 kiB) Run-tested on: GL.iNet GL-MT300N-V2 (mt76x8) D-Link DWR-116 (mt7620) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-01 22:59:32 +0000