aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621/base-files/etc
Commit message (Collapse)AuthorAgeFilesLines
* ramips: read label MAC address from flash instead of using phy0/phy1Adrian Schmutzler2019-11-131-4/+4
| | | | | | | | This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress) by retrieval from the proper flash locations. This will make 02_network independent of WiFi setup again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: split further base-files across subtargetsAdrian Schmutzler2019-11-112-0/+27
| | | | | | | | | | | As started in 19724e28c81e ("ramips: split base-files into subtargets"), this moves some smaller left-over files to the appropriate base-files folder of their subtarget: - /etc/init.d/bootcount - /etc/uci-defaults/04_led_migration Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve support for WeVO 11AC NAS and W2914NS v2Sungbo Eo2019-11-061-6/+9
| | | | | | | | | | | | | | | | | | | | | | | | | - remove WAN port index - load WAN MAC address directly from the flash - provide label MAC address - increase flash's SPI frequency to 80MHz - add mt76 led nodes to make WiFi LEDs work - drop unnecessary pinmux groups The factory partition scheme for MAC addresses (verified on both devices): 0x4 : WiFi 2.4GHz (label_mac-9) 0x28 : unused 0x2e : WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-5) 0xe000: LAN (label_mac-1) 0xe006: unused By improving flash speed, `time dd if=/dev/mtdblock3 of=/dev/null bs=64k` has been reduced from 14.51s to 3.11s. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebased] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default case for MAC address assignmentAdrian Schmutzler2019-11-061-6/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, MAC address assignment in ramips has contained a default case, which defined wan_mac = eth0 + 1 for _every_ device not having an explicit case there. This is not desirable, as many device supporters will just not care or know about this definition, so another MAC address will be introduced by accident. In some cases the wan_mac is assigned although it is not needed, in other cases even addresses not dedicated to the device will be used (e.g. wan_mac actually is eth0 - 1, but during support nobody cared, so eth0 + 1 is used now, which might actually belong to another device ...). Thus, in this PR the former default case is converted to an explicit case. This one comprises all devices not being accounted for by other cases, reduced by those not having wan at all. The big number of entries for this node might be another indication that many of them wouldn't actually be there if there hadn't been default wan_mac setup. In exchange, the current "do nothing" case can be removed, as it will be the new default case. The devices being put in the newly created explicit case were determined as follows: 1. Create a list of all devices based on the DTS files. 2. Remove all devices already having an explicit entry setting their address. 3. Remove all devices that only have lan set up in the first part of 02_network: mt7620: - alfa-network,tube-e4g - asus,rp-n53 - buffalo,wmr-300 - comfast,cf-wr800n - edimax,ew-7476rpc - edimax,ew-7478ac - elecom,wrh-300cr - hnet,c108 - kimax,u25awf-h1 - kimax,u35wf - kingston,mlw221 - kingston,mlwg2 - microduino,microwrt - netgear,ex2700 - netgear,ex3700 - netgear,wn3000rp-v3 - planex,cs-qr10 - planex,mzk-ex300np - planex,mzk-ex750np - ravpower,wd03 - sercomm,na930 - yukai,bocco - zbtlink,zbt-cpe102 - zte,q7 mt7621: - gnubee,gb-pc1 - gnubee,gb-pc2 - linksys,re6500 - mikrotik,rbm11g - netgear,ex6150 - thunder,timecloud - tplink,re350-v1 - tplink,re650-v1 mt76x8: - alfa-network,awusfree1 - d-team,pbr-d1 - glinet,vixmini - vocore,vocore2-lite - tama,w06 - tplink,tl-mr3020-v3 - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 - vocore,vocore2 - widora,neo-16m - widora,neo-32m rt288x: - buffalo,wli-tx4-ag300n - dlink,dap-1522-a1 rt305x: - allnet,all0256n-4m - allnet,all0256n-8m - allnet,all5002 - allnet,all5003 - alphanetworks,asl26555-16m - alphanetworks,asl26555-8m - asus,wl-330n - aximcom,mr-102n - dlink,dcs-930 - easyacc,wizard-8800 - hame,mpr-a2 - hootoo,ht-tm02 - huawei,d105 - intenso,memory2move - planex,mzk-dp150n - rt305x dlink,dcs-930l-b1 - sparklan,wcr-150gn - tenda,3g150b - tenda,3g300m - tenda,w150m - trendnet,tew-638apb-v2 - unbranded,a5-v11 - vocore,vocore-16m - vocore,vocore-8m - wansview,ncs601w - zorlik,zl5900v2 rt3883: - loewe,wmdr-143n - omnima,hpm 4. Put the remaining devices in the new case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve netis WF-2881 supportSungbo Eo2019-11-061-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch does the following: 1. remove u-boot-env partition Stock bootloader saves env variables at 0x80000 in flash, and there is nothing stored at 0x30000. By merging the partition "u-boot-env" with "u-boot", the partition table becomes the same as used in stock firmware: 00000000-00080000: "Bootloader" 00080000-00100000: "Config" 00100000-00140000: "Factory" 00140000-07f80000: "Kernel" 2. fix LAN/WAN MAC addresses and provide label MAC address Ethernet MAC addresses are stored in factory partition at: 0xe000: LAN (label_mac) 0xe006: WAN (label_mac+1) 3. fix LAN port order WF-2881 LAN ports are in reverse order of switch ports. 4. fix WiFi LEDs mt76 led nodes are added to make WiFi LEDs work. On top of this, mt76 node names are changed to more generic ones, and compatible strings are also added. 5. fix pinmux groups uart3 and uart2 pins are used as button and led, but jtag pins are not. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: split base-files into subtargetsAdrian Schmutzler2019-11-033-0/+351
While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space. In certain cases, keeping files in parent (=target) base-files was more convenient, and thus no splitting was performed for those. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (mt7621) 60958 B split (mt7620) 46358 B (- 14.3 kiB) split (mt7621) 48759 B (- 11.9 kiB) split (mt76x8) 44948 B (- 15.6 kiB) split (rt288x) 43508 B (- 17.0 kiB) split (rt305x) 45616 B (- 15.0 kiB) split (rt3883) 44176 B (- 16.4 kiB) Run-tested on: GL.iNet GL-MT300N-V2 (mt76x8) D-Link DWR-116 (mt7620) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 03:53:38 +0000