aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621/base-files/etc/hotplug.d
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix Tenbay T-MB5EU v1 Wireless MACDavid Bauer2021-12-151-0/+5
| | | | | | | | | | | | | It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC address set on 2.4 and 5 GHz. Some boards do not seem to have the correct MAC address set for the external PHY of the MT7915 radio at caldata offset 0xa. As the external PHY does not expose a DT binding (yet), fix up the mac address in userspace. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix Wifi MAC address setup for D-Link DIR-853 R1Adrian Schmutzler2021-07-121-3/+3
| | | | | | | | Commands in 10_fix_wifi_mac were not properly concatenated, so this was also triggered for the second phy without giving a MAC address as argument. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-853 A3Karim Dehouche2021-07-121-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7621AT * RAM: 256MB * Flash: 128MB NAND flash * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * LAN: 5x1000M * Firmware layout is Uboot with extra 96 bytes in header * Base PCB is DIR-1360 REV1.0 * LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons Reset,WPS, Wifi MAC addresses on OEM firmware: lan factory 0xe000 f4:*:*:a8:*:65 (label) wan factory 0xe006 f4:*:*:a8:*:68 2.4 GHz [not on flash] f6:*:*:c8:*:66 5.0 GHz factory 0x4 f4:*:*:a8:*:66 The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20 x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20 x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Flashing instruction: The Dlink "Emergency Room" cannot be accessed through the reset button on this device. You can either use console or use the encrypted factory image availble in the openwrt forum. Once the encrypted image is flashed throuh the stock Dlink web interface, the sysupgrade images can be used. Header pins needs to be soldered near the WPS and Wifi buttons. The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC. the settings are: Bps/Par/Bits : 57600 8N1 Hardware Flow Control : No Software Flow Control : No Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.101 / 255.255.255.0. Call the recovery page or tftp for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device At the time of adding support the wireless config needs to be set up by editing the wireless config file: * Setting the country code is mandatory, otherwise the router loses connectivity at the next reboot. This is mandatory and can be done from luci. After setting the country code the router boots correctly. A reset with the reset button will fix the issue and the user has to reconfigure. * This is minor since the 5g interface does not come up online although it is not set as disabled. 2 options here: 1- Either run the "wifi" command. Can be added from LUCI in system - startup - local startup and just add wifi above "exit 0". 2- Or add the serialize option in the wireless config file as shown below. This one would work and bring both interfaces automatically at every boot: config wifi-device 'radio0' option serialize '1' config wifi-device 'radio1' option serialize '1' Signed-off-by: Karim Dehouche <karimdplay@gmail.com> [rebase, improve MAC table, update wireless config comment, fix 2.4g macaddr setup] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v2Tee Hao Wei2021-07-111-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
* ramips: add support for D-Link DIR-853-R1Stas Fiduchi2021-07-101-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for router D-Link DIR-853-R1 Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB SPI WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the same time) LAN: 5x1000M LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue USB Blue Buttons Reset,WPS, Wifi MAC addresses: |Interface | MAC | Factory |Comment |------------|-----------------|-------------|---------------- |WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker |LAN |C4:XX:XX:6E:XX:2B| | |Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 | |Wifi (2.4g) |C6:XX:XX:7E:XX:2C| | | | | | | |C4:XX:XX:6E:XX:2E|0x8004 0xe000| | |C4:XX:XX:6E:XX:2F|0xe006 | The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10 f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20 F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Flashing instruction: The Dlink "Emergency Room" Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.101 / 255.255.255.0. Then, power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing Call the recovery page or tftp for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com> [commit title/message improvements, use correct label MAC address, calculate MAC addresses based on 0x4, minor DTS style fixes, add uart2 to state_default, remove factory image, add 2.4g MAC address, use partition DTSI, add macaddr comment in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys E5600Aashish Kulkarni2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Linksys EA7300 v1/ v2. Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: 128M DDR3-1600 * Flash: 128M NAND * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz) * Antennae: 2 internal fixed in the casing and 2 on the PCB * LEDs: Blue (x4 Ethernet) Blue+Orange (x2 Power + WPS and Internet) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This device has 2 partitions for the firmware called firmware and alt_firmware. To successfully flash and boot the device, the device should have been running from alt_firmware partition. To get the device booted through alt_firmware partition, download the OEM firmware from Linksys website and upgrade the firmware from web GUI. Once this is done, flash the OpenWrt Factory firmware from web GUI. Reverting to factory firmware: 1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of the following: Press the "wps" button as soon as power LED turns on when booting. (OR) Hard-reset the router consecutively three times to force it to boot from 'alt_firmware'. 2. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com> [fix hanging indents and wrap to 74 characters per line, add kmod-mt7663-firmware-sta package for 5GHz STA mode to work, remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk, set default-state "on" for power LED] Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com> [move check-size before append-metadata, remove trailing whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG Q20Chukun Pan2021-05-261-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add support for GL.iNet GL-MT1300Xinfa Deng2020-12-171-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL-MT1300 is a high-performance new generation pocket-sized router that offers a powerful hardware and first-class cybersecurity protocol with unique and modern design. Specifications: - SoC: MT7621A, Dual-Core @880MHz - RAM: 256 MB DDR3 - Flash: 32 MB - Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN - Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps) - USB: 1 x USB 3.0 port - Slot: 1 x MicroSD card slot - Button: 1 x Reset button - Switch: 1 x Mode switch - LED: 1 x Blue LED + 1 x White LED MAC addresses based on vendor firmware: WAN : factory 0x4000 LAN : Mac from factory 0x4000 + 1 2.4GHz : factory 0x4 5GHz : Mac form factory 0x4 + 1 Flashing instructions: 1.Connect to one of LAN ports. 2.Set the static IP on the PC to 192.168.1.2. 3.Press the Reset button and power the device (do not release the button). After waiting for the blue led to flash 5 times, the white led will come on and release the button. 4.Browse the 192.168.1.1 web page and update firmware according to web tips. 5.The blue led will flash when the firmware is being upgraded. 6.The blue led stops blinking to indicate that the firmware upgrade is complete and U-Boot automatically starts the firmware. For more information on GL-MT1300, see the OFFICIAL GL.iNet website: https://www.gl-inet.com/products/gl-mt1300/ Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com> [add input-type for switch, wrap long line in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v2J. Scott Heppler2020-09-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Santiago Rodriguez-Papa <contact at rodsan.dev> Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Winbond W632GG6MB-12 (256M DDR3-1600) * Flash: Winbond W29N01HVSINA (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
* ramips: add support for Linksys EA7300 v1Santiago Rodriguez-Papa2020-07-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Everything works! Been running it for a couple weeks now and haven't had any problems. Please let me know if you run into any. Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev> [use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7500 v2Davide Fioravanti2020-05-171-0/+18
The Linksys EA7500 v2 is advertised as AC1900, but its internal hardware is AC2600 capable. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 256M (Nanya NT5CC128M16IP-DI) FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI) ETH: 5x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615N (4x4:4) - 5GHz: 1x MT7615N (4x4:4) - 4 antennas: 3 external detachable antennas and 1 internal USB: - 1x USB 3.0 - 1x USB 2.0 BTN: - 1x Reset button - 1x WPS button LEDS: - 1x White led (Power) - 6x Green leds (link lan1-lan4, link wan, wps) - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable) Everything works correctly. Installation ------------ The “factory” openwrt image can be flashed directly from OEM stock firmware. After the flash the router will reboot automatically. However, due to the dual boot system, the first installation could fail (if you want to know why, read the footnotes). If the flash succeed and you can reach OpenWrt through the web interface or ssh, you are done. Otherwise the router will try to boot 3 times and then will automatically boot the OEM firmware (don’t turn off the router. Simply wait and try to reach the router through the web interface every now and then, it will take few minutes). After this, you should be back in the OEM firmware. Now you have to flash the OEM Firmware over itself using the OEM web interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img downloaded from the Linksys website). When the router reboots flash the “factory” OpenWrt image and this time it should work. After the OpenWrt installation you have to use the sysupgrade image for future updates. Restore OEM Firmware -------------------- After the OpenWrt flash, the OEM firmware is still stored in the second partition thanks to the dual boot system. You can switch from OpenWrt to OEM firmware and vice-versa failing the boot 3 times in a row: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware If you want to completely remove OpenWrt from your router, switch to the OEM firmware and then flash OEM firmware from the web interface as a normal update. This procedure will overwrite the OpenWrt partition. Footnotes --------- The Linksys EA7500-v2 has a dual boot system to avoid bricks. This system works using 2 pair of partitions: 1) "kernel" and "rootfs" 2) "alt_kernel" and "alt_rootfs". After 3 failed boot attempts, the bootloader tries to boot the other pair of partitions and so on. This system is managed by the bootloader, which writes a bootcount in the s_env partition, and if successfully booted, the system add a "zero-bootcount" after the previous value. A system update performed from OEM firmware, writes the firmware on the other pair of partitions and sets the bootloader to boot the new pair of partitions editing the “boot_part” variable in the bootloader vars. Effectively it's a quick and safe system to switch the selected boot partition. Another way to switch the boot partition is: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware In this OpenWrt port, this dual boot system is partially working because the bootloader sets the right rootfs partition in the cmdline but unfortunately OpenWrt for ramips platform overwrites the cmdline so is not possible to detect the right rootfs partition. Because all of this, I preferred to simply use the first pair of partitions and set read-only the other pair. However this solution is not optimal because is not possible to know without opening the case which is the current booted partition. Let’s take for example a router booting the OEM firmware from the first pair of partitions. If we flash the OpenWrt image, it will be written on the second pair. In this situation the router will bootloop 3 times and then will automatically come back to the first pair of partitions containg the OEM firmware. In this situation, to flash OpenWrt correctly is necessary to switch the booting partition, flashing again the OEM firmware over itself. At this point the OEM firmware is on both pair of partitions but the current booted pair is the second one. Now, flashing the OpenWrt factory image will write the firmware on the first pair and then will boot correctly. If this limitation in the ramips platform about the cmdline will be fixed, the dual boot system can also be implemented in OpenWrt with almost no effort. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Co-Developed-by: Jackson Lim <jackcolentern@gmail.com> Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-19 11:24:18 +0000