aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7620
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-134-8/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: support dual image feature on ALFA Network boardsPiotr Dymacz2019-11-132-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards includes support for a 'dual image' feature. Users can enable it using U-Boot environment variable 'dual_image' ('1' -> enabled). When 'dual image' feature is enabled, U-Boot will modify DTB and divide the original 'firmware' flash area into two, equal in size and aligned to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust size of 'firmware' area to match installed flash chip size. U-Boot will load kernel from active partition which is marked with env variable 'bootactive' ('1' -> first partition, '2' -> second partition) and rename both partitions accordingly ('firmware' <-> 'backup'). There are 3 additional env variables used to control 'dual image' mode: - bootlimit - maximum number of unsuccessful boot tries (default: '3') - bootcount - current number of boot tries - bootchanged - flag which informs that active partition was changed; if it is set and 'bootcount' reaches 'bootlimit' value, U-Boot will start web-based recovery which then updates both partitions with provided image Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: read label MAC address from flash instead of using phy0/phy1Adrian Schmutzler2019-11-131-3/+3
| | | | | | | | This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress) by retrieval from the proper flash locations. This will make 02_network independent of WiFi setup again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: split further base-files across subtargetsAdrian Schmutzler2019-11-111-0/+49
| | | | | | | | | | | As started in 19724e28c81e ("ramips: split base-files into subtargets"), this moves some smaller left-over files to the appropriate base-files folder of their subtarget: - /etc/init.d/bootcount - /etc/uci-defaults/04_led_migration Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6130Frederik Noe-Sdun2019-11-082-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. The device seems to use base PCB as EX3700/EX3800, but supporting AC1200 using MT7612E. MAC adresses: 5.0 GHz 0x8004 *:9a 2.4 GHz 0x4 *:9b lan 0x28 *:9b wan 0x2e *:9c Since this is a one-port device, although wan MAC address is set in flash, it is not used in OpenWrt setup. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, extended commit message, tiny DTS style fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default case for MAC address assignmentAdrian Schmutzler2019-11-061-8/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, MAC address assignment in ramips has contained a default case, which defined wan_mac = eth0 + 1 for _every_ device not having an explicit case there. This is not desirable, as many device supporters will just not care or know about this definition, so another MAC address will be introduced by accident. In some cases the wan_mac is assigned although it is not needed, in other cases even addresses not dedicated to the device will be used (e.g. wan_mac actually is eth0 - 1, but during support nobody cared, so eth0 + 1 is used now, which might actually belong to another device ...). Thus, in this PR the former default case is converted to an explicit case. This one comprises all devices not being accounted for by other cases, reduced by those not having wan at all. The big number of entries for this node might be another indication that many of them wouldn't actually be there if there hadn't been default wan_mac setup. In exchange, the current "do nothing" case can be removed, as it will be the new default case. The devices being put in the newly created explicit case were determined as follows: 1. Create a list of all devices based on the DTS files. 2. Remove all devices already having an explicit entry setting their address. 3. Remove all devices that only have lan set up in the first part of 02_network: mt7620: - alfa-network,tube-e4g - asus,rp-n53 - buffalo,wmr-300 - comfast,cf-wr800n - edimax,ew-7476rpc - edimax,ew-7478ac - elecom,wrh-300cr - hnet,c108 - kimax,u25awf-h1 - kimax,u35wf - kingston,mlw221 - kingston,mlwg2 - microduino,microwrt - netgear,ex2700 - netgear,ex3700 - netgear,wn3000rp-v3 - planex,cs-qr10 - planex,mzk-ex300np - planex,mzk-ex750np - ravpower,wd03 - sercomm,na930 - yukai,bocco - zbtlink,zbt-cpe102 - zte,q7 mt7621: - gnubee,gb-pc1 - gnubee,gb-pc2 - linksys,re6500 - mikrotik,rbm11g - netgear,ex6150 - thunder,timecloud - tplink,re350-v1 - tplink,re650-v1 mt76x8: - alfa-network,awusfree1 - d-team,pbr-d1 - glinet,vixmini - vocore,vocore2-lite - tama,w06 - tplink,tl-mr3020-v3 - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 - vocore,vocore2 - widora,neo-16m - widora,neo-32m rt288x: - buffalo,wli-tx4-ag300n - dlink,dap-1522-a1 rt305x: - allnet,all0256n-4m - allnet,all0256n-8m - allnet,all5002 - allnet,all5003 - alphanetworks,asl26555-16m - alphanetworks,asl26555-8m - asus,wl-330n - aximcom,mr-102n - dlink,dcs-930 - easyacc,wizard-8800 - hame,mpr-a2 - hootoo,ht-tm02 - huawei,d105 - intenso,memory2move - planex,mzk-dp150n - rt305x dlink,dcs-930l-b1 - sparklan,wcr-150gn - tenda,3g150b - tenda,3g300m - tenda,w150m - trendnet,tew-638apb-v2 - unbranded,a5-v11 - vocore,vocore-16m - vocore,vocore-8m - wansview,ncs601w - zorlik,zl5900v2 rt3883: - loewe,wmdr-143n - omnima,hpm 4. Put the remaining devices in the new case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ZBT WE1026-HKristian Evensen2019-11-032-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * When binding the USB LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [rebased onto base-files split, minor style fixes, removed use of USB led as power LED] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: update ZBT WE1026 DTS-filesKristian Evensen2019-11-031-0/+3
| | | | | | | | | | | | | | | | | | | | | | This commit makes the following changes to the WE1026 DTS-files: * The parts that are unique to the -5G-version (LED and 5GHz wifi) are moved to a separate file, so that WE1026.dtsi can be referenced also by the DTS for the -H version. * Use the generic "flash"-name for the spi-nor node. * Add label MAC. All changes have been tested on the WE1026-5G-16M and work fine. I.e., the device works as before the DTS-changes. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Mathias Kresin <dev@kresin.me> Acked-by: Alex Maclean <monkeh@monkeh.net> Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Petr Štetiar <ynezz@true.cz> [minor style fixes, rebased onto base-files split, remove obsolete gpio-keys comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix Xiaomi MiWiFi Mini switch definitionChih-Wei Chen2019-11-031-2/+2
| | | | | | | | | | | | | | | | | | | | | Based on OpenWRT Table of Hardware > Xiaomi > Xiaomi Mi WiFi Mini Switch Ports Defaults: 0, 1: LAN 4: WAN 6: CPU Port in Web GUI (word printed on bottom of case) WAN(Internet) map to switch port 4 LAN1(.) map to switch port 1 LAN2(..) map to switch port 0 CPU map to switch port 6 current setting is 1 WAN/ 4 LAN port, fix it. Signed-off-by: Chih-Wei Chen <changeway@gmail.com> [rebased after base-files split, fixed commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: split base-files into subtargetsAdrian Schmutzler2019-11-035-0/+616
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space. In certain cases, keeping files in parent (=target) base-files was more convenient, and thus no splitting was performed for those. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (mt7621) 60958 B split (mt7620) 46358 B (- 14.3 kiB) split (mt7621) 48759 B (- 11.9 kiB) split (mt76x8) 44948 B (- 15.6 kiB) split (rt288x) 43508 B (- 17.0 kiB) split (rt305x) 45616 B (- 15.0 kiB) split (rt3883) 44176 B (- 16.4 kiB) Run-tested on: GL.iNet GL-MT300N-V2 (mt76x8) D-Link DWR-116 (mt7620) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-1/+1
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTBChuanhong Guo2019-07-081-2/+2
| | | | | | | | | | | | | | | | | Upstream kernel added support for RAW_APPENDED_DTB on ralink arch in the following commit: 02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink") Use upstream solution and get rid of our OWRTDTB hack. This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with DEVICE_DTS in device profile because DTS variable will be dropped in later commits. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Tested on mt7621/mt76x8] Tested-by: Chuanhong Guo <gch981213@gmail.com> [Tested on rt305x/mt7620] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: fix dependenciesDeng Qingfang2019-05-111-1/+1
| | | | | | | | | | | | | MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies according to original Kconfig and lsmod output This will remove some unnecessary packages from MT7620 target to save some space Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 characters per line in the commit message]
* ramips: disable CONFIG_MTD_SPLIT_FIRMWAREMathias Kresin2019-01-261-1/+0
| | | | | | | It's no longer needed as all mt7621 devices use DT binding (supported by upstream mtd code) for specifying "firmware" part format explicitly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: select only the matching mt76 driverChen Minqiang2018-12-031-1/+1
| | | | | | | | | | | | | Because every device has selected the corresponding mt76 driver, we can now disable the mt76 metapackage by default to make sure that other devices (those don't need mt76) avoid selecting unwanted packages. We can find the hardware specifies and determine the dependencies on these sites: https://wikidevi.com/wiki/ https://openwrt.org/toh/hwdata/ Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for Lava LR-25G001Pawel Dembicki2018-11-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Lava LR-25G001 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN) - 2x external, detachable antennas - 1x USB 2.0 - UART (J3) header on PCB (57600 8n1) - 8x LED (3x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - Work only three Gigabit ports (3/5, 1 WAN and 2LAN) Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-1/+1
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: only optimized for size if small_flashMathias Kresin2018-07-121-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | Add a new config option to allow to select the default compile optimization level for the kernel. Select the optimization for size by default if the small_flash feature is set. Otherwise "Optimize for performance" is set. Add the small_flash feature flag to all (sub)targets which had the optimization for size in their default kernel config. Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new setting. Exceptions to the above are: - lantiq, where the optimization for size is only required for the xway_legacy subtarget but was set for the whole target - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have plenty of space and an optimization for size doesn't make much sense - rb532, which has 128MByte flash Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: drop linux 4.9 supportFelix Fietkau2018-04-061-215/+0
| | | | | | | 4.14 has been tested a lot by a number of users, and we want to use it for the release. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for D-Link DWR-116-A1/2Pawel Dembicki2018-03-182-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC. Specification: MediaTek MT7620N (580 Mhz) 32 MB of RAM 8 MB of FLASH 802.11bgn radio 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) 2x external, non-detachable antennas UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1) 6x LED (GPIO-controlled), 2x button JBOOT bootloader Known issues: WAN LED is drived by uartl tx pin. I decide to use this pin as uartlite tx pin. Installation: Apply factory image via http web-gui. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: optimize for performance by default starting with 4.14Felix Fietkau2018-02-241-0/+2
| | | | | | Keep size optimizations for smaller targets that already switched Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: preliminary support for 4.14Roman Yeryomin2018-02-151-0/+240
| | | | | | | | - removed upstreamed patches - 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed Signed-off-by: Roman Yeryomin <roman@advem.lv> Signed-off-by: John Crispin <john@phrozen.org>
* kernel: add support for limiting 4K erase sector support based on flash chip ↵Felix Fietkau2017-11-061-0/+1
| | | | | | | | | | | | | | | | size Some targets need 4K sectors for small flash chips (e.g. some routerboards, where the entire chip is just one "erase block"), whereas on other devices 4K sectors lead to horrible flash erase/write performance. Set the default limit in the generic kernel configuration to 4 MiB to ensure that all new platforms don't use 4K sectors for bigger flash chips. On all existing targets use 16 MiB for now to avoid regressions. They will be changed individually in follow-up commits. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: drop stray kernel 4.4 configsMathias Kresin2017-07-271-210/+0
| | | | | | | The kernel 4.4 patches where already removed with the bump to 4.9. Drop the the subtarget configs as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: cleanup CONFIG_SCHED_HRTICKStijn Tintel2017-06-292-2/+0
| | | | | | | Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the generic config in b47fd7656336162360ebf66147326763ddae3f8d. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: disable CONFIG_SG_POOL by defaultSergey Ryazanov2017-06-071-1/+0
| | | | | | | | CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last one is disabled by default then disable CONFIG_SG_POOL by default too. And explicitly enable it only for platforms that use CONFIG_SCSI. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: purge default packages on MT7621Daniel Golle2017-05-041-1/+1
| | | | | | | | | | | | | | In order to have a smaller initramfs image remove all packages not needed on all devices and add them explicitely for those actually needing them. Also remove wpad-mini from ramips default package set and add it to all sub-targets except for MT7621. While at it reorder packages alphabetically and replace kmod-mt76 with kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on a specific board. Hopefully fixes FS#758 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add v4.9 supportJohn Crispin2017-02-141-0/+215
| | | | | | NAND support is missing Signed-off-by: John Crispin <john@phrozen.org>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-1/+1
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: enable 4K sector support in kernel configMathias Kresin2016-09-131-0/+1
| | | | | | | | | | | | This is a follow up to 28110727f1d513a6c4c13aa87ecb606aa5d306eb "ramips: set blocksize for 4MB devices". I've missed to include the required changes of the kernel configs to enable 4K sector size support. The option is only enabled for targets having boards with 4k sector size flash chips. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: switch from 24kec to 24kcJonas Gorski2016-08-081-1/+1
| | | | | | | | Since the only difference between 24Kec and 24Kc is the addition of DSP ASE support, and we don't use it anymore, there is no need to keep 24Kec as a separate cpu type. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* build: remove MIPS dsp/dsp2 CPU_SUBTYPEFelix Fietkau2016-08-031-1/+0
| | | | | | | There does not seem to be any meaningful difference in generated code. This will save some time and space on snapshot builds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: Improve TP-Link Archer C20i supportP.Wassi2016-07-261-0/+1
| | | | | | Improve / finalise TP-Link Archer C20i support. Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: enable MTD_SPLIT_SEAMA_FW for mt7620Michael Lee2016-07-111-0/+1
| | | | Signed-off-by: Michael Lee <igvtee@gmail.com>
* ramips: fix the number of uarts for each SoCÁlvaro Fernández Rojas2016-06-031-1/+0
| | | | | | | | - Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620. - Allow up to 3 uarts on MT7621 and MT7628. - Remove unneeded SERIAL_8250_RT288X for MT7628. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: set default profile to priority 1John Crispin2016-05-141-0/+1
| | | | | | doing so will sort all profiles alphabetically Signed-off-by: John Crispin <john@phrozen.org>
* ramips: convert mt7620 to new image building codeJohn Crispin2016-05-1214-304/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for Planex MZK-EX750NP.blogic2016-05-101-0/+11
| | | | | | | | | | | add support for Planex MZK-EX750NP. MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49268
* target: globally remove ARCH_PACKAGES overridesJo-Philipp Wich2016-04-171-1/+0
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for Planex MZK-EX300NPJohn Crispin2016-04-261-0/+11
| | | | | | | | | | MZK-EX300NP is MT7620A based wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49235
* ramips: add support for Planex CS-QR10John Crispin2016-04-261-0/+14
| | | | | | | | | | | | CS-QR10 is MT7620A based IP Camera. the camera and sound does not work with kernel 4.4. - camera chip is sn9c291. - sound chip is wm8960. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49234
* ramips: add support for ELECOM WRH-300CRJohn Crispin2016-04-211-0/+18
| | | | | | | | | | | | | | ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but easy-to-access) UART. it also has internal USB hub and USB card reader which provide one USB port, one SD card slot, and one microSD card slot. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> SVN-Revision: 49211
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 03:58:58 +0000