aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ASUS RT-N56U B1Pavel Chervontsev2020-11-281-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621ST (880 MHz) FLASH: 16 MiB (Macronix MX25L12835FM2I-10G) RAM: 128 MiB (Nanya NT5CB64M16FP-DH) WiFi: MediaTek MT7603EN bgn 2x2:2 WiFi: MediaTek MT7612EN an 2x2:2 BTN: Reset, WPS LED: - Power - WiFi 2.4 GHz - WiFi 5 GHz - WAN - LAN {1-4} - USB {1-2} UART: UART is present as pin hole next to the aluminium capacitor. 3V3 - RX - GND - TX / 115200-8N1 3V3 is the nearest on the aluminium capacitor and nut hole (pin1). USB: 2 ports POWER: 12VDC, 1.5A (Barrel 5.5x2.1) Installation: Via TFTP: Set your computers IP-Address to 192.168.1.75 Power up the Router with the Reset button pressed. Release the Reset button after 5 seconds. Upload OpenWRT sysupgrade image via TFTP: tftp -4 -v -m binary 192.168.1.1 -c put IMAGE MAC addresses: 0x4 *:98 2g/wan, label 0x22 *:9c 0x28 *:98 0x8004 *:9c 5g/lan Though addresses are written to 0x22 and 0x28, it appears that the vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the same here. Signed-off-by: Pavel Chervontsev <cherpash@gmail.com> [add MAC address overview, add label-mac-device, fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: replace missing custom-initramfs-uimageSander Vanheule2020-11-261-1/+1
| | | | | | | | | | custom-initramfs-uimage was replaced by calls to uImage, but apparently mtc_wr1201 was missed in the transistion. Use uImage for this device too. Fixes: 9f574b1b875c "ramips: mt7621: drop custom uImage function" Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: add support for Xiaomi Mi Router 4CAtaberk Özen2020-11-251-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi's Mi Router 4C device. Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LEDs: 2x yellow/blue. Programmable (labelled as power on case) - Non-programmable (shows WAN activity) - Button: Reset How to install: 1- Use OpenWRTInvasion to gain telnet and ftp access. 2- Push openwrt firmware to /tmp/ using ftp. 3- Connect to router using telnet. (IP: 192.168.31.1 - Username: root - No password) 4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into the router.. 5- It takes around 2 minutes. After that router will restart itself to OpenWrt. Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com> [wrap commit message, bump PKG_RELEASE for uboot-envtools, remove dts-v1 from DTS, fix LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: drop custom uImage functionSander Vanheule2020-11-251-21/+10
| | | | | | | | Use the mkimage argument overrides provided by uImage to implement the customisations required for the initramfs, instead of the near-identical custom function. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: add support for TP-Link MR6400 v5Filip Moc2020-11-251-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are: - smaller form factor - different LED GPIOs - different switch connections You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v5.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for TP-Link MR6400 v4Filip Moc2020-11-231-0/+16
| | | | | | | | | | | | | | | | | | | | | | | You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v4.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for the Hak5 WiFi Pineapple Mark 7Marc Egerton2020-11-181-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WiFi Pineapple Mark 7, a wireless penetration testing tool. Specifications: * SoC: MediaTek MT7628 (580MHz) * RAM: 256MiB (DDR2) * Storage 1: 32MiB NOR (SPI) * Storage 2: 2GB eMMC * Wireless 1: 802.11b/g/n 2.4GHz (Built In) * Wireless 2: 802.11b/g/n 2.4GHz (MT7601) * Wireless 3: 802.11b/g/n 2.4GHz (MT7601) * USB: 1x USB Type-A 2.0 Host Port * Ethernet: 1x USB Type-C AX88772C Ethernet * UART: 57600 8N1 on PCB * Inputs: 1x Reset Button * Outputs: 1x RGB LED * FCCID: 2AA52MK7 Flash Instructions: Original firmware is based on OpenWRT. Use sysupgrade via SSH to flash. Signed-off-by: Marc Egerton <foxtrot@realloc.me> [pepe2k@gmail.com: set only required/used gpio groups to gpio function] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add Xiaomi Mi Router 4A Gigabit explicitlyAdrian Schmutzler2020-11-121-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-2640 A1James McGuire2020-11-111-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-2640 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue), WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:a7 (label) wan factory 0xe006 *:aa 2.4 factory 0xe000 +1 *:a8 5.0 factory 0xe000 +2 *:a9 Seems like vendor didn't replace the dummy entries in the calibration data. Signed-off-by: James McGuire <jamesm51@gmail.com> [fix device definition title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mt7621: mikrotik: use vmlinuz (zBoot ELF)John Thomson2020-10-291-2/+2
| | | | | | | | | | | | - minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz - ~5 seconds for kernel decompression, which was equivalent to the additional time to load the uncompressed ELF from SPI NOR. - Removes requirement for lzma-loader, which may have been causing some image builds to fail to boot on Mikrotik mt7621. Fixes: FS#3354 Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* ramips: add support for Wavlink WL-WN530HG4Nuno Goncalves2020-10-271-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | Same hardware as Phicomm K2G but different flash layout. Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: To avoid requiring UART for TFTP a dual flash procedure is suggested to install the squashfs image: 1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin to WN530HG4-WAVLINK. 2. Flash this file with the factory web interface. 3. With OpenWRT now running use standard sysupgrade to install the squashfs image. Signed-off-by: Nuno Goncalves <nunojpg@gmail.com> [remove dts-v1, remove model from LED labels, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: use lzma-loader for U7621-06Jianhui Zhao2020-10-251-0/+2
| | | | | | | The U7621-06 fails to boot if the kernel is large. Enabling lzma-loader resolves the issue. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* ramips: add support for TOTOLINK X5000RChuanhong Guo2020-10-251-0/+10
| | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 16MB (EN25QH128A) - Ethernet: 5xGbE - WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps Known issue: MT7915 DBDC variant isn't supported yet. Flash instruction: Upload the sysupgrade firmware to the firmware upgrade page in vendor fw. Other info: MT7915 seems to have two PCIEs connected to MT7621. Card detected on PCIE0 has an ID of 14c3:7916 and the other one on PCIE1 has 14c3:7915. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for TP-Link RE200 v4Richard Fröhning2020-10-201-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2/v3. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button - UART connection holes on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:8E 2.4G: *:8D 5G : *:8C MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [removed empty line, fix commit message formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Linksys EA7300 v2J. Scott Heppler2020-09-231-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Santiago Rodriguez-Papa <contact at rodsan.dev> Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Winbond W632GG6MB-12 (256M DDR3-1600) * Flash: Winbond W29N01HVSINA (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
* ramips: mt7621: pbr-m1: fix firmware sizeChuanhong Guo2020-09-131-1/+1
| | | | | | | This board is equipped with Winbond W25Q256FV 32M SPI-NOR. Fix partition size for that. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix partitions and boot for RAVPower RP-WD03Adrian Schmutzler2020-09-111-7/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD03 is a battery powered router, with an Ethernet and USB port. Due due a limitation in the vendor supplied U-Boot bootloader, we cannot exceed a 1.5 MB kernel size, as is the case with recent builds (i.e. post v19.07). This breaks both factory and sysupgrade images. To address this, use the lzma loader (loader-okli) to work around this limitation. The improvements here also address the "misplaced" U-Boot environment partition, which is located between the kernel and rootfs in the stock image / implementation. This is addressed by making use of mtd-concat, maximizing space available in the booted image. This will make sysupgrade from earlier versions impossible. Changes are based on the recently supported HooToo HT-TM05, as the hardware is almost identical (except for RAM size) and is from the same vendor (SunValley). While at it, also change the SPI frequency accordingly. Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions Most of the changes in this commit are the work of Russell Morris (as credited below), I only wrapped them up and added compat-version. Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader to work! Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use proper name for RAVPower RP-WD03Adrian Schmutzler2020-09-111-4/+5
| | | | | | | | The proper model name is RP-WD03 (i.e. with the RP- prefix). Adjust all names to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move ravpower-wd009-factory recipe to mt76x8.mkAdrian Schmutzler2020-09-112-6/+8
| | | | | | | The recipe is only used for a single device, so put it in the subtarget file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: disable default build for Ravpower RP-WD03Adrian Schmutzler2020-09-091-0/+1
| | | | | | | | | | This device has a 1.5M kernel size limit during boot and is unbootable since February 2019 [1]. [1] https://forum.openwrt.org/t/ravpower-wd03-does-not-start-with-openwrt-master/49792 Reported-by: Szabolcs Hubai <szab.hu@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "treewide: add sysupgrade comment for early DSA-adopters"Adrian Schmutzler2020-09-081-2/+1
| | | | | | | | | | This reverts commit e81e625ca375d6dc3c885ec870ec15757ac76d72. This was meant just for early DSA-adopters. Those should have updated by now, remove it so future updaters get the intended experience. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-2660 A1Josh Bendavid2020-09-061-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-2660 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white), WiFi 5G (white), USB 3.0 (white), USB 2.0 (white) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:a7 (label) wan factory 0xe006 *:aa 2.4 factory 0xe000 +1 *:a8 5.0 factory 0xe000 +2 *:a9 Seems like vendor didn't replace the dummy entries in the calibration data. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com> [rebase onto already merged DIR-1960 A1, add MAC addresses to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for HooToo HT-TM05Russell Morris2020-09-032-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port. Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli). Specifications: SOC: MediaTek MT7620N BATTERY: 10400mAh WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: 64 MB FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz Flash itself specified to 80 MHz, but speed limited by mt7620 SPI fast-read enabled (m25p) LED: Status LED (blue after boot, green with WiFi traffic 4 leds to indicate power level of the battery (unable to control) INPUT: Power, reset button MAC assignment based on vendor firmware: 2.4 GHz *:b4 (factory 0x04) LAN/label *:b4 (factory 0x28) WAN *:b5 (factory 0x2e) Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - Installation from TFTP (recovery) - OpenWRT sysupgrade (Preserving and non-preserving), through the usual ways: command line and LuCI - LEDs (except as noted above) - Button (reset) - I2C, which is needed for reading battery charge status and level - U-Boot environment / variables (from U-Boot, and OpenWrt) Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions I would like to thank @mpratt14 and @xabolcs for their help getting the lzma loader to work! Signed-off-by: Russell Morris <rmorris@rkmorris.us> [drop changes in image/Makefile, fix indent and PKG_RELEASE in uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift, add COMPILE to Device/Default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: image: add recipe for OKLI loaderChuanhong Guo2020-09-031-1/+17
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: lzma-loader: make FLASH_START configurableChuanhong Guo2020-09-033-4/+8
| | | | | | | | | | | FLASH_START is supposed to point at the memory area where NOR flash are mapped. We currently have an incorrect FLASH_START copied from ar71xx back then and the loader doesn't work under OKLI mode. On ramips, mt7621 has it's flash mapped to 0x1fc00000 and other SoCs uses 0x1c000000. This commit makes FLASH_START a configurable value to handle both cases. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: rt3883: use lzma-loader for DIR-645Perry Melange2020-08-281-0/+1
| | | | | | | | | The DIR-645 fails to boot if the kernel is large. Enabling lzma-loader resolves the issue. Run-tested on D-Link DIR-645. Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
* ramips: add support for Wavlink WL-WN531A6Georgi Vlaev2020-08-281-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Wavlink WL-WN531A6 (Quantum D6). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK * Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG * WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot. * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot. * Ethernet: MT7630, 5x 1000Base-T * LED: Power, WAN, LAN(x4), WiFi, WPS, dual color "WAVLINK" LED logo on the top cover. * Buttons: Reset, WPS, "Turbo", touch button on the top cover via RH6015C touch sensor. * UART: UART1: serial console (57600 8n1) on the J4 header located below the top heatsink. UART2: J12 header, located on the right side of the board. * USB: One USB3 port. * I2C: J9 header, located below the top heatsink. Backup the OEM Firmware: ----------------------- There isn't any firmware released for the WL-WN531A6 on the Wavlink web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware is stored on /dev/mtd4 ("Kernel"). 1) Plug a FAT32 formatted USB flash drive into the USB port. 2) Navigate to "Setup->USB Storage". Under the "Available Network folder" you can see part of the mount point of the newly mounted flash drive filesystem - e.g "sda1". The full mount point is prefixed with "/media", so in this case the mount point becomes "/media/sda1". 3) Go to http://192.168.10.1/webcmd.shtml . 4) Type the following line in the "Command" input box: dd if=/dev/mtd4ro of=/media/sda1/firmware.bin 5) Click "Apply" 6) After few seconds, in the text area should appear this output: 30080+0 records in 30080+0 records out 7) Type "sync" in the "Command" input box and click "Apply". 8) At this point the OEM firmware is stored on the flash drive as "firmware.bin". The size of the file is 15040 KB. Installation: ------------ * Flashing instructions (OEM web interface): The OEM web interface accepts only files with names containing "WN531A6". It's also impossible to flash the *-sysupgrade.bin image, so we have to flash the *-initramfs-kernel.bin first and use the OpenWrt's upgrade interface to write the sysupgrade image. 1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin to WN531A6.bin. 2) Connect your computer to the one of the LAN ports of the router with an Ethernet cable and open http://192.168.10.1 3) Browse to Setup -> Firmware Upgrade interface. 4) Upload the (renamed) OpenWrt image - WN531A6.bin. 5) Proceed with the firmware installation and give the device a few minutes to finish and reboot. 6) After reboot wait for the "WAVLINK" logo on the top cover to turn solid blue, and open http://192.168.1.1 7) Use the OpenWrt's "Flash Firmware" interface to write the OpenWrt sysupgrade image: openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin * Flashing instructions (u-boot TFTP): 1) Configure a TFTP server on your computer and set its IP to 192.168.10.100 2) Rename the OpenWrt sysupgrade image to firmware.bin and place it in the root folder of the TFTP server. 3) Power off the device and connect an Ethernet cable from one of its LAN ports your computer. 4) Press the "Reset" button (and keep it pressed) 5) Power on the device. 6) After a few seconds, when the connected port LAN LED stops blinking fast, release the "Reset" button. 7) Flashing OpenWrt takes less than a minute, system will reboot automatically. 8) After reboot the WAVLINK logo on the top cover will indicate the current OpenWrt running status (wait until the logo tunrs solid blue). Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow "Flashing instructions (u-boot TFTP)" and use the "firmware.bin" backup image. * OpenWrt "Flash Firmware" interface: Upload the "firmware.bin" backup image and select "Force update" before continuing. Notes: ----- * The MAC address shown on the label at the back of the device is assigned to the 2.4G WiFi adapter. MAC addresses assigned by the OEM firmware: 2.4G: *:XX (label): factory@0x0004 5G: *:XX + 1 : factory@0x8004 WAN: *:XX - 1 : factory@0xe006 LAN: *:XX - 2 : factory@0xe000 * The I2C bus and UART2 are fully functional. The headers are not populated. Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
* ramips: add support for TP-Link TL-WR850N v2Andrew Freeman2020-08-271-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR850N v2. This device is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13. Specifications: SOC: MediaTek MT7628NN Flash: 8 MiB SPI RAM: 64 MiB WLAN: MediaTek MT7628NN Ethernet: 5 ports (100M) Installation Using the integrated tftp capability of the router: 1. Turn off the router. 2. Connect pc to one of the router LAN ports. 3. Set your PC IPv4 address to 192.168.0.66/24. 4. Run any TFTP server on the PC. 5. Put the recovery firmware on the root directory of TFTP server and name the file tp_recovery.bin 6. Start the router by pressing power button while holding the WPS/Reset button (or both WPS/Reset and WIFI buttons) 7. Router connects to your PC with IPv4 address 192.168.0.2, downloads the firmware, installs it and reboots. LEDs are flashing. Now you have OpenWrt installed. 8. Change your IPv4 PC address to something in 192.168.1.0/24 network or use DHCP to get an address from your OpenWrt router. 9. Done! You can login to your router via ssh. Forum link: https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899 Signed-off-by: Andrew Freeman <labz56@gmail.com> [squash an tidy up commits, sort nodes] Signed-off-by: Darsh Patel <darshkpatel@gmail.com> [minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: use lzma-loader for ZBT-WG3526Rustam Gaptulin2020-08-241-0/+2
| | | | | | | | | | | | The wg3526 fails to boot if the kernel is large. Enabling lzma-loader resolves the issue on both the wg3526-16m and wg3526-32m. Fixes: FS#3143 Signed-off-by: Rustam Gaptulin <rascal6@gmail.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-202-19/+19
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)John Thomson2020-08-131-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 760iGS router. It is similar to the already supported RouterBOARD 750Gr3. The 760iGS device features an added SFP cage, and passive PoE out on port 5 compared to the RB750Gr3. https://mikrotik.com/product/hex_s Specifications: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB - RAM: 256 MB - Ethernet: 5x 10/100/1000 Mbps - SFP cage - USB port - microSD slot Unsupported: - Beeper (requires PWM driver) - ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1) The linux driver requires an interrupt, and pendown GPIO These are unknown, and not needed with the touchscreen only used for temperature and voltage monitoring. ads7846 hwmon: temp0 is degrees Celsius temp1 is voltage * 32 GPIOs: - 07: input passive PoE out (lan5) compatible (Mikrotik) device connected - 17: output passive PoE out (lan5) switch Installation through RouterBoot follows the usual MikroTik method https://openwrt.org/toh/mikrotik/common To boot to intramfs image in RAM: 1. Setup TFTP server to serve intramfs image. 2. Plug Ethernet cable into WAN port. 3. Unplug power, hold reset button and plug power in. Wait (~25 seconds) for beep and then release reset button. The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT. 4. Wait for a minute. Router should be running OpenWrt, check by plugging in to port 2-5 and going to 192.168.1.1. To install OpenWrt to flash: 1. Follow steps above to boot intramfs image in RAM. 2. Flash the sysupgrade.bin image with web interface or sysupgrade. 3. Once the router reboots you will be running OpenWrt from flash. OEM firmware differences: - RouterOS assigns a different MAC address for each port - The first address (E01 on the sticker) is used for wan (ether1 in OEM). - The next address is used for lan2. - The last address (E06 on the sticker) is used for sfp. [Initial port work, shared dtsi] Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com> [SFP support and GPIO identification] Signed-off-by: Luka Logar <luka.logar@iname.com> [Misc. fixes and submission] Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [rebase, drop uart3 from state_default on 750gr3, minor commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use gpio-export for Mikrotik RouterBOARD 750Gr3 beeperJohn Thomson2020-08-131-1/+1
| | | | | | | | | | | | | This beeper hardware requires a PWM driver for frequency selection. Since the GPIO driver does not provide that, revert the beeper support to a simple gpio-export. This effectively reverts the corresponding changes from 6ba58b7b020c ("ramips: cleanup the RB750Gr3 support") Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: make dependency on kmod-usb-net selectiveAdrian Schmutzler2020-08-102-2/+2
| | | | | | | | A bunch of kernel modules depends on kmod-usb-net, but does not select it. Make AddDepends/usb-net selective, so we can drop some redundant +kmod-usb-net definitions for DEVICE_PACKAGES. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: add sysupgrade comment for early DSA-adoptersAdrian Schmutzler2020-08-081-1/+2
| | | | | | | | | | Add a specific comment for early DSA-adopters that they can keep their config when prompted due to compat-version increase. This is a temporary solution, the patch should be simply reverted before any release. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: implement compatibility version for DSA migrationAdrian Schmutzler2020-08-081-0/+82
| | | | | | | | | | | | | | | | | | | This implements the newly introduced compat-version to prevent broken upgrade between swconfig and DSA for ramips' mt7621 subtarget. In order to make the situation more transparent for the user, and to prevent large switch-cases for devices, it is more convenient to have the entire subtarget 1.1-by-default. This means that new devices will be added with 1.1 from the start, but in contrast we don't need to switch them in board.d files. Apart from that, users that manually backport devices to 19.07 with swconfig will have an equivalent upgrade experience to officially supported devices. Since DSA support on mt7621 is out for a while already, this applies the same uci-defaults workaround for early adopters as already done for kirkwood and mvebu in previous commits. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use lzma-loader for RT5350F-OLinuXino devicesSungbo Eo2020-08-081-0/+2
| | | | | | | The bootloader fails to extract a big kernel, e.g. v5.4 kernel image with ALL_KMODS enabled. This can be fixed by using lzma-loader. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: adjust LZMA_TEXT_START for 32MB RAM devicesSungbo Eo2020-08-081-1/+1
| | | | | | | | | | Currently the lzma-loader is placed in RAM at 32MB offset, which does not make sense for devices with only 32MB RAM. If we adjust LZMA_TEXT_START to 24MB offset, then the lzma-loader can be used on those devices and still about 24MB memory will be available for uncompressed image, which should be enough for most use cases. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: invert wpad selection for mt7621Adrian Schmutzler2020-08-071-80/+87
| | | | | | | | | | | | | | | | | | | For ramips/mt7621, the wpad-basic package is not selected by default, but added for every device individually as needed. While this might be technically correct if the SoC does not come with a Wifi module, only 18 of 97 devices for that platform are set up _without_ wpad-basic currently. Therefore, it seems more convenient to add wpad-basic by default for the subtarget and then just remove it for the 18 mentioned devices, instead of having to add it for about 60 times instead. This would also match the behavior of the 5 other subtargets, where wpad-basic/wpad-mini is added by default as well, and thus be more obvious to developers without detailed SoC knowledge. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear JWNR2010 v5Shibajee Roy2020-08-061-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7620N (580 MHz) - Flash size: 4 MB NOR SPI - RAM size: 32 MB DDR1 - Bootloader: U-Boot - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz) - Switch: MT7620 built-in 10/100 switch with vlan support - Ports: 4x LAN, 1x WAN - Others: 7x LED, Reset button, UART header on PCB (57600 8N1) Flash instructions: 1. Use ethernet cable to connect router with PC/Laptop, any router LAN port will work. 2. To flash openwrt we are using nmrpflash[1]. 3. Flash commands: First we need to identify the correct Ethernet id. nmrpflash -L nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.) 4. Now remove the power cable from router back side and immediately connect it again. You will see flash notification in CMD window, once it says reboot the device just plug off the router and plug in again. Revert to stock: 1. Download the stock firmware from official netgear support[2]. 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware. nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img MAC addresses on stock firmware: LAN = *:28 (label) WAN = *:29 WLAN = *:28 On flash, the only valid MAC address is found in factory 0x4. Special Note: This openwrt firmware will also support other netgear N300 routers like below as they share same stock firmware[3]. JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050 [1] https://github.com/jclehner/nmrpflash [2] https://www.netgear.com/support/product/JWNR2010v5.aspx [3] http://kb.netgear.com/000059663 Signed-off-by: Shibajee Roy <ador250@protonmail.com> [create DTSI, use netgear_sercomm_nor, disable by default, add MAC addresses to commit message, add label MAC address] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add common definition netgear_sercomm_norAdrian Schmutzler2020-08-063-27/+24
| | | | | | | | Like NAND-based devices, SPI-NOR based Netgear devices also share a common setup for their images. This creates a common defition for them in image/Makefile, so it can be reused across subtargets. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable flashing WizFi630S via OEM firmwareTobias Welz2020-08-051-0/+1
| | | | | | | | | | | WIZnet WizFi630s board name is written slightly different it its OEM OpenWrt firmware. This causes an incompatibility warning during flashing with sysupgrade. This patch is adding the vendor board name to the supported devices list to avoid this warning. For initial flashing you can use sysupgrade via command line or luci beside of TFTP. Do not keep the OEM configuration during sysupgrade. Signed-off-by: Tobias Welz <tw@wiznet.eu>
* ramips: add support for TP-Link RE200 v3Richard Fröhning2020-08-031-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button Unverified: - UART header on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. The device has not been opened for adding support. However, it is expected that the behavior is similar to the RE200 v2. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [adjust commit title/message, sort support list] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix/tidy up 4M tplink-v2-image flash layoutsAdrian Schmutzler2020-08-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | For the TP-Link 4M devices with tplink-v2-image recipe (mktplinkfw2.c), there are two different flash layouts based on the size of the (u)boot partition: device uboot OEM firmware OpenWrt (incl. config) tl-wr840n-v5 0x20000 0x3c0000 0x3d0000 tl-wr841n-v14 0x10000 0x3d0000 0x3e0000 In both cases, the 0x10000 config partition is used for the firmware partition as well due to the limited space available and since it's recreated by the OEM firmware anyway. However, the TFTP flashing process will only copy data up to the size of the initial (OEM) firmware size. Therefore, while we can use the bigger partition to have additional erase blocks on the device, we have to limit the image sizes to the TFTP limits. So far, only one layout definition has been set up in mktplinkfw2.c for 4M mediatek devices. This adds a second one and assigns them to the devices so the image sizes are correctly restrained. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JS76x8 series DEV boardsRobinson Wu2020-07-311-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Jotale JS76x8 series development boards. These devices have the following specifications: - SOC: MT7628AN/NN, MT7688AN, MT7628DAN - RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2) - RAM of MT7628DAN: 64 MB (DDR2) - FLASH:8/16/32 MB (SPI NOR) - Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch) - WIFI:1x 2T2R 2.4 GHz Wi-Fi - LEDs:1x system status green LED, 1x wifi green LED, 3x ethernet green LED - Buttons:1x reset button - 1x microSD slot - 4x USB 2.0 port - 1x mini-usb debug UART - 1x DC jack for main power (DC 5V) - 1x TTL/RS232 UART - 1x TTL/RS485 UART - 13x GPIO header - 1x audio codec(wm8960) Installation via OpenWrt: The original firmware is OpenWrt, so both LuCI and sysupgrade can be used. Installation via U-boot web: 1. Power on board with reset button pressed, release it after wifi led start blinking. 2. Setup static IP 192.168.1.123/4 on your PC. 3. Go to 192.168.1.8 in browser and upload "sysupgrade" image. Installation via U-boot tftp: 1. Connect to serial console at the mini usb, which has been connected to UART0 on board (115200 8N1) 2. Setup static IP 192.168.1.123/4 on your PC. 3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123). 3. Connect one of LAN ports on board to your PC. 4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC. 5. Apply power to board. 6. Interrupt U-boot with keypress of "2". 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (192.168.1.8) ==:192.168.1.8 Input server IP (192.168.1.123) ==:192.168.1.123 Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin 8. board will download file from tftp server, write it to flash and reboot. Signed-off-by: Robinson Wu <wurobinson@qq.com> [add license to DTS files, fix state_default and reduce to the mimimum, move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-1960 A1Josh Bendavid2020-07-271-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-1960 A1. Given the similarity with the DIR-1760/2660 A1, this patch also introduces a common DTSI which can be shared with these devices, with support to be added in future commits. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white), WiFi 5G (white), USB 3.0 (white) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:EB (label) wan factory 0xe006 *:EE 2.4 factory 0xe000 +1 *:EC 5.0 factory 0xe000 +2 *:ED Seems like vendor didn't replace the dummy entrys in the calibration data. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com> [fix whitespace issues, create patch to merge DIR-1960 first, move special WiFi MAC settings to DTS, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Winstars WS-WN583A6Davide Fioravanti2020-07-251-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet ports. Even if mine is branded as "Gemeita AC2100", the sticker on the back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6. Probably the real product name is the Wavlink WL-WN583A6 because of the many references to Wavlink in the OEM firmware and bootlog. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 8MB NOR (GigaDevice GD25Q64B) ETH: 2x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7603E (2x2:2) - 5GHz: 1x MT7615E (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x WPS button - 1x ON/OFF switch (working but unmodifiable) - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3) LEDS: - 1x White led - 1x Red led - 1x Amber led - 1x Blue led - 2x Blue leds (lan and wan port status: working but unmodifiable) UART: - 57600-8-N-1 Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M83A6.V5030.191210 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box: mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done 3) Click "Apply" 4) After few seconds, in the textarea should appear this output: 16384+0 records in 16384+0 records out 8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s 384+0 records in 384+0 records out 196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s 15744+0 records in 15744+0 records out 8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s dd: can't open '/dev/mtd5ro': No such device dd: can't open '/dev/mtd6ro': No such device dd: can't open '/dev/mtd7ro': No such device Excluding the "X.XXXXXX seconds" part, you should get the same exact output. If your output doesn't match mine, stop reading and ask for help in the forum. 5) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd0ro http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files weight 0 byte, stop reading and ask for help in the forum. 6) Store these downloaded files in a safe place. 7) Reboot your router to remove any temporary file from your router. Installation ------------ Flash the initramfs image in the OEM firmware interface. When openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) The "System Command" page allows to run every command as root. For example you can use "dd" and "nc" to backup the OEM firmware. PC (SERVER): nc -l 5555 > ./mtdXro ROUTER (CLIENT): dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555 2) The OEM web interface accepts only images containing the string "WN583A6" in the filename. Currently the OEM interface accepts only the initramfs image probably because it checks if the ih_size in the image header is equal to the whole image size (instead of the kernel size) Read more here: https://forum.openwrt.org/t/support-for-strong-1200/22768/19 3) The white led (namely "Smart Night Light") can be controller by the user only if the side switch is set to "Schedule" otherwise it will be activated by the light condition (there is a photodiode on the top side of the router) 4) Router mac addresses: LAN XX:XX:XX:XX:XX:8F WAN XX:XX:XX:XX:XX:90 WIFI 2G XX:XX:XX:XX:XX:91 WIFI 5G XX:XX:XX:XX:XX:92 LABEL XX:XX:XX:XX:XX:91 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [remove chosen node, fix whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"Adrian Schmutzler2020-07-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 1623defbdbb852a4018329d07673b4b8f66225a8. As already stated in the reverted patch, the OEM firmware will properly recreate the config partition if it is overwritten by OpenWrt. The main reason for adding the partition was the image size restriction imposed by the 0x3d0000 limitation of the TFTP flashing process. Addressing this by shrinking the firmware partition is not a good solution to that problem, though: 1. For a working image, the size of the content has to be smaller than the available space, so empty erase blocks will remain. 2. Conceptually, the restriction is on the image, so it makes sense to implement it in the same way, and not via the partitioning. Users could e.g. do initial flash with TFTP restriction with an older image, and then sysupgrade into a newer one, so TFTP restriction does not apply. 3. The (content) size of the recovery image is enforced to 0x3d0000 by the tplink-v2-image command in combination with TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix flash layout for TP-Link TL-WR841N v14Alexander Müller2020-07-191-1/+1
| | | | | | | | | | | | | | | | The config partition was missing from the flash layout of the device. Although the stock firmware resets a corrupted config partition to the default values, the TFTP flash with an image bigger than 0x3d0000 will truncate the image as the bootloader only copies 0x3d0000 bytes to flash during TFTP flashing. Fixed by adding the config partition and shrinking the firmware partition. Fixes: 3fd97c522bb7 ("ramips: add support for TP-Link TL-WR841n v14") Signed-off-by: Alexander Müller <donothingloop@gmail.com>
* ramips: add support for D-Link DIR-867/DIR-882 A1Mateus B. Cassiano2020-07-161-9/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v1Santiago Rodriguez-Papa2020-07-161-6/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Everything works! Been running it for a couple weeks now and haven't had any problems. Please let me know if you run into any. Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev> [use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 20:46:59 +0000