aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ZIO FREEZIOSungbo Eo2019-12-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7603EN - 5GHz: MT7612EN - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1x 3.0 - UART: - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 Notes: - FREEZIO has almost the same board as WeVO W2914NS v2. - Stock firmware is based on OpenWrt BB. MAC addresses in factory partition: 0x0004: WiFi 2.4GHz (label_mac-8) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-4) 0xe000: LAN (label_mac+1) Installation via web interface: 1. Access web admin page and turn on "OpenWrt UI mode". 2. Flash sysupgrade image through LuCI, with the "Keep settings" option OFF. Revert to stock firmware: 1. Perform sysupgrade with stock image. Make sure to NOT preserve settings. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebase, use mt7621_wevo_w2914ns-v2.dtsi] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove unused DTS variable from DEVICE_VARSAdrian Schmutzler2019-12-121-1/+1
| | | | | | | | | | | | | The DTS variable has been removed in 402138d12dca ("ramips: Derive DTS name from device name in Makefile"), but the DEVICE_VARS entry has been overlooked. Remove it now since we are not using this variable. This must _not_ be backported to 19.07, where the variable is still in use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: set uImage name of WeVO 11AC NAS and W2914NS v2Sungbo Eo2019-11-171-0/+2
| | | | | | | | | | | | | The stock firmware and bootloader only accept uImage with names that match certain patterns. This patch enables OpenWrt installation from stock firmware without having to reflash the bootloader or access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-141-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM, USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support. Specification: - MT7621A (880 MHz) - 256/512 MB of RAM (DDR3) - 16/32+ MB of FLASH (SPI NOR) - optional second SPI flash (8-pin WSON/SOIC) - 1x microSD (SDXC) flash card reader - 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1 - optional 802.3at/af PoE module for WAN - 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V) - 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM) - RTC (TI BQ32002, I2C bus) with backup battery (CR2032) - external hardware watchdog (EM Microelectronic EM6324) - 1x USB 2.0 Type-A - 1x micro USB Type-B for system serial console (Holtek HT42B534) - 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator) - 3x button (reset, user1, user2) - 1x I2C (4-pin, 2.54 mm pitch) header on PCB - 4x SIM (6-pin, 2.00 mm pitch) headers on PCB - 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB - 1x mechanical power switch - 1x DC jack with lock (24 V) Other: - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board has additional logic circuit for M.2 SIM switching. The 'sim-select' will work only if both SIM slots are occupied. Otherwise, always slot with SIM inside is selected, no matter 'sim-select' value. - U-Boot enables power in all three miniPCIe and M.2 slots before loading the kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) - all three miniPCIe slots have additional 5 V supply on pins 47 and 49 - the board allows to install up to two oversized miniPCIe cards (vendor has dedicated MediaTek MT7615N/D cards for this board) - this board has additional logic circuit controlling PERSTn pins inside miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe slots but setting GPIO22 to high allows PERSTn control per slot, using GPIO23-25 (value is inverted) You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100Sungbo Eo2019-11-131-1/+1
| | | | | | | | | CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing in default images. This commit adds it. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [changed commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6130Frederik Noe-Sdun2019-11-081-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. The device seems to use base PCB as EX3700/EX3800, but supporting AC1200 using MT7612E. MAC adresses: 5.0 GHz 0x8004 *:9a 2.4 GHz 0x4 *:9b lan 0x28 *:9b wan 0x2e *:9c Since this is a one-port device, although wan MAC address is set in flash, it is not used in OpenWrt setup. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, extended commit message, tiny DTS style fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips, mt7620: reproducible elecom-header uid/gidPaul Spooren2019-11-061-1/+1
| | | | | | | | | | | | | | | | | | | | | The elecom-header renames the firmware image to v_0.0.0.bin, stores its MD5 sum as v_0.0.0.md5 and tars both files again. Both v_0.0.0 files are created as the build user making it harder to reproduce. This commit sets the owner/group of both files to root by adding extra options to the final tar command. Before: 0 buildbot (101) buildbot (102) 3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin 0 buildbot (101) buildbot (102) 33 2019-11-05 14:43:22.000000 v_0.0.0.md5 After: 0 root (0) root (0) 3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin 0 root (0) root (0) 33 2019-11-05 23:43:08.000000 v_0.0.0.md5 Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: fix MTK_SOC for RT3662 devicesSungbo Eo2019-11-041-6/+6
| | | | | | | | | | | rt3883.mk contains both RT3662 and RT3883 device profiles, but commit 6a104ac77206 set MTK_SOC to rt3883 for all devices. This patch fixes it, and renames dts files accordingly. And SoC compatible strings are also appended in the dts. Fixes: 6a104ac77206 ("ramips/rt288x,rt3883: Name DTS files based on scheme") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ZBT WE1026-HKristian Evensen2019-11-031-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * When binding the USB LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [rebased onto base-files split, minor style fixes, removed use of USB led as power LED] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve common definition for Netgear R6xxx in mt7621.mkAdrian Schmutzler2019-11-031-31/+36
| | | | | | | | | | | | | This patch renames and reassembles the common definition for Netgear R6xxx devices in mt7621.mk. The following goals should be achieved: - Give the node a more generic name instead of adding devices to it - Use the common definition in the (less) similar R6220 node - Include/exclude settings into the common definition so the common node contains the common definitions - Prepare for support of R6700 v2 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2Paul Fertser2019-10-271-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CMIIT ID: 2019AP2581 - SoC: MediaTek MT7621 - Flash: 16MiB NOR SPI (GigaDevice GD25Q128B) - RAM: 128MiB DDR3 (ESMT M15T1G1664A) - Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset INSTALLATION: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware (looks like an illegal OpenWrt fork) won't accept any serial input unless "uart_en" is set to "1". Tricks to force u-boot to use default environment do not help as it's restricted in the same way. With bootloader unlocked the easiest way would be to TFTP the sysupgrade image or to sysupgrade after loading an initramfs one. For porting the flash contents were changed externally with an SPI programmer (after lifting Vcc flash IC pin away from the PCB). Forum thread [0] indicates that this device is identical to "Xiaomi Mi Router 4A Gigabit Edition". [0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ramips: add support for Asus RT-AC65PGabor Varga2019-10-241-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it. On both routers the installation can be done also via SSH: Note: The user/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt factory image via scp: > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.50.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux 6. Reboot the router > reboot Changelog: v3: removed [] from filename, rebased to latest master v2: Rebased to latest master v1: Initial release Signed-off-by: Gabor Varga <vargagab@gmail.com>
* ramips: fix TARGET_DEVICES after UniElec renameAdrian Schmutzler2019-10-212-3/+3
| | | | | | | | | | Device node names were updated, but updating TARGET_DEVICES was overlooked. Fixes: 4408723d42e0 ("ramips: remove RAM size from device name for UniElec devices") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove RAM size from device name for UniElec devicesAdrian Schmutzler2019-10-212-8/+9
| | | | | | | | | | | UniElec devices are the last ones in ramips target still having the RAM size in device name although RAM size is auto-detected. Remove this from device name, compatible, etc., as it's not required and might be misleading to users and developers adding device support copying those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: Alternative name KE 2P for Phicomm K2PRoger Pueyo Centelles2019-10-131-0/+2
| | | | | | | | The Phicomm KE 2P is identical to the already supported Phicomm K2P, renamed for the European market. Use the ALT0 buildroot tags to show both devices. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-064-45/+45
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: apply consistent device name/compatible to ZBT-WE1026-5GAdrian Schmutzler2019-09-291-11/+11
| | | | | | | | | | | All Zbtlink ramips devices except the ZBT-WE1026-5G include the zbt-/ZBT- prefix in their model name. This changes ZBT-WE1026-5G to also follow that scheme. The patch moves some block to keep alphatical order. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: harmonize device vendor ZbtlinkAdrian Schmutzler2019-09-292-6/+6
| | | | | | | | | | | | Spelling of Zbtlink varies across image definitions and DTS files. This patch uses Zbtlink consistently and also updates the model in DTS files to contain the vendor in all cases. This patch is cosmetical, as there should be no dependencies on device model name in ramips anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WNPR2600GINAGAKI Hiroshi2019-09-251-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7615 - 5 GHz : MediaTek MT7615 - Ethernet : 10/100/1000 Mbps - Switch : MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from SoC side - 57600n8 Flash instruction using factory image: 1. Boot WNPR2600G normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mkINAGAKI Hiroshi2019-09-253-38/+20
| | | | | | | | | | | I-O DATA WNPR2600G has an "elx-header", so move this definition to generic makefile to use it from mt7621 subtarget. This definition is also added to mt7621.mk in f285e8634c57d28aa970b80c5c59e85485f35c7d, so remove it from mt7621.mk. And added a line to cleanup used header file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ipTIME A3Sungbo Eo2019-09-251-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for XiaoYu XY-C5Qi Jiang2019-09-251-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621A Flash: 32 MiB RAM: 512 MiB Ethernet: built-in switch USB: 1x USB3.0 SATA: ASM1060, 1 SATA port Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.173.22 2. Download *-sysupgrade.bin image and rename it to firmware.img 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Turn on router,press the reset button and wait ~15 seconds 6. Release the reset button and after a short time the firmware should be transferred from the tftp server 7. Wait ~3 minutes to complete recovery. Signed-off-by: Qi Jiang <rushx@live.cn> [squash commits, add label-mac-device, fix sign-off style] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-201-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: Add new device AsiaRF AP7621-NV1Daniel Danzberger2019-09-201-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN) POE: (1x PD, 2x PSE) USB: 1x 3.0 PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface) GPS: Quectel L70B SIM: 2 Slots BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ The stock image is a modified openwrt and can be overflashed via sysupgrade -F Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> [merge conflict in mt7621.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Asus RT-AC85PBirger Koblitz2019-09-201-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Winbond W632GG6KB-1) FLASH: 128MB (Macronix MX30LF1G18AC-TI) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x USB 3.1 (Gen 1) BTN: Reset, WPS LED: - Power (blue) - 5Ghz (blue) - 2.4GHz (blue) - Internet (blue) - 4x LAN (blue) (LAN/WAN leds are not controllable by GPIOs) UART: UART is present as Pads marked J4 on the PCB. 3.3V - TX - RX - GND / 57600-8N1 3.3V is the square pad MAC: The MAC address on the router-label matches the MAC of the 2.4 GHz WiFi. LAN and WAN MAC are identical: MAC_LABEL+4 5 GHz WiFi MAC: also MAC_LABEL+4 Installation ------------ Via U-Boot tftpd: Switch on device, within 2s press reset button and keep pressed until power LED starts blinking slowly. Upload factory image via tftp put, the router's ip is 192.168.1.1 and expects the client on 192.168.1.75. The images also work on the Asus RT-AC65P models as tested by Gabor. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Tested-by: Gabor Varga <vargagab@gmail.com> [fixed Asus -> ASUS in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax RG21SBirger Koblitz2019-09-201-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Nanya NT5CC128M) FLASH: 16MB (Macronix MX25L12835F) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: No BTN: Reset, WPS LED: 4 red LEDs, indistinguishable when casing closed UART: UART is present as Pads marked J1 on the PCB. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the OEM web-interface (by default:http://192.168.1.1) The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect ethernet port 2. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [flash node rename, EDIMAX -> Edimax, complete device model name] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add SD-Card support for Linkit Smart 7688Ivan Hörler2019-09-151-1/+1
| | | | | | The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working. Signed-off-by: Ivan Hörler <i.hoerler@me.com>
* ramips: improve support for Xiaomi Miwifi NanoChuanhong Guo2019-09-041-1/+1
| | | | | | | | | | | | | | | This patch does the following things: 1. mark u-boot-env writable 2. add bootcount support Currently, u-boot has a flag_boot_success env variable to reset. Also reset it in our firmware to follow the behavior in vendor's firmware. 3. disable usb support This router doesn't have usb port at all. 4. increase spi clock to 40MHz 5. fix pinmux groups Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for Netgear R6260 and R6850Christoph Krapp2019-08-311-2/+18
| | | | | | | | | | | As Netgear uses the same image for R6260, R6350 & R6850 we can merge device tree files and generate separate images for each device. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [add missing WiFi compatible string, fix network configuration] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add factory image for Netgear R6350Christoph Krapp2019-08-311-1/+6
| | | | | | | | | | | | This adds factory image generation for all three devices. These images can be flashed via WebUI for easy installation. Thanks to David Bauer for the inspiration. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [altered commit to only include the R6350] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add mt7615e support to Netgear R6350Christoph Krapp2019-08-311-1/+1
| | | | Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ramips: add factory image for NETGEAR R6220David Bauer2019-08-311-1/+6
| | | | | | | | | | This adds an easy-installation factory image for the NETGEAR R6220 router. The factory image can either be flashed via the vendor Web-UI or the bootloader using nmrpflash. Tested with NETGEAR V1.1.0.86 firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add NAS goodies on U25AWF-H1 + U35[N|W]FChristian Lamparter2019-08-241-2/+4
| | | | | | | | | These devices are sold as a "NAS HDD Enclousure" and have a "NAS Media Streaming & File Server & AP" on the box. That's why I think they should have some support for the HDD right out-of-the-box. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ADSLR G7Zhenjian Zhang2019-08-241-0/+9
| | | | | | | | | | | | | | | | | | | SoC: MT7621AT RAM: 256MB Flash: 16M SPI Ethernet: 5x GE ports WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: 1.Modify the file to linux.bin 2.Set up FTP service 3.Computer settings fixed IP: 192.168.179.50 255.255.255.0 4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds. Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com> [fix mac location] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add device alias for Allnet ALL0239-3GDaniel Golle2019-08-221-0/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips/mt76x8: add DEVICE_VENDOR for tl-wr840n-v5Paul Spooren2019-08-221-0/+1
| | | | | | DEVICE_VENDOR is missing for this device. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: add support for ipTIME A604MSungbo Eo2019-08-171-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 5x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* Revert faulty tree pushFelix Fietkau2019-08-121-21/+0
| | | | | | | | | | | | Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85e5381c93d73ffdbc24c130400e0fb8) Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e7502507b31f0fb82befbb48f9c8542) Revert "ramips: add preliminary support for WIO ONE" (085141dc5ba5e763e1bf4c1a2fd6957160810ccc) Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539511f60bf65fbde28b16afa31180e34) Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d4f6c00b4a7cb83dd1821fafc0d40ad) Revert "toolchain: add autoconf-lean" (fdb30eed03ae56cd87078b64d9b2fac00799e783) Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758524eddf20c9b66dfcb55c490e1961e) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add preliminary support for WIO ONEFelix Fietkau2019-08-121-0/+10
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add preliminary support for SGE AP-MTKH7-0006 developer boardFelix Fietkau2019-08-121-0/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add kmod-mt7615e to Xiaomi Mi Router 3 Pro imagesOzgur Can Leonard2019-08-101-1/+2
| | | | | | Now that the mt76/mt7615e driver is in Openwrt, might as well use it. Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
* ramips: add support for HiWiFi HC5761ADENG Qingfang2019-08-081-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi HC5761A is an "MT7628AN variant" of HC5761 Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7610EN 802.11ac 433Mbps - 3x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Known bug: - SD slot does not work (See PR 1500) Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for Fon FON2601NOGUCHI Hiroshi2019-07-262-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FON2601 is a wireless router. Specification: - SoC: Mediatek MT7620A (580MHz) - RAM: 128 MiB - ROM: 16 MiB SPI Flash - Wireless: for 11b/g/n (upto 300 Mbps): MT7620A built-in WMAC for 11a/n/ac (upto 867 Mbps): MT7662E - Ethernet LAN: 1 port, upto 100 Mbps - Ethernet WAN: 1 port, upto 1000 Mbps - USB: 1 port (USB 2.0 host) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 1 (Displayed as "WPS" on enclosure) - serial port: 57600n8 pins: Vcc(3.3V), Rx, Tx, GND (left to right, viewed from outside of board) Installation (only available via UART): 1. download sysupgrade binary image by wget command 2. write sysupgrade binary image to Flash command is: mtd write sysupgrade.bin firmware 3. reboot Important Notice: Only one button is displayed as "WPS" on enclosure. However, it is configured as "reset" (factory resetting feature). Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: use kiB instead of B for IMAGE_SIZEAdrian Schmutzler2019-07-254-4/+4
| | | | | | | This cosmetical patch is just meant to make comparing/checking IMAGE_SIZE values easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove ralink_default_fw_size_xxx variablesAdrian Schmutzler2019-07-257-187/+182
| | | | | | | | | | | There are frequent examples of the ralink_default_fw_size_xxx variables being used to "roughly" set flash size without caring about the actual size of the firmware partition. To discourage this behavior, this patch removes the variables and just sets IMAGE_SIZE by its numeric value for each target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default IMAGE_SIZE for ramips targetAdrian Schmutzler2019-07-256-1/+66
| | | | | | | | | | | | | | | | | | | Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE for all devices in ramips target, i.e. this will be set if a device does not specify IMAGE_SIZE itself. From 92 devices using that default due to a "missing" IMAGE_SIZE, 14 were incorrect by a small amount (i.e. still "8M" flash) and 12 were completely off ("16M", "4M", ...). This patch thus removes the _default_ IMAGE_SIZE and defines IMAGE_SIZE for each device individually. This should indicate to people supporting new devices that this parameter has to be cared about. For the present code, this patch is cosmetical. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt305x: fix IMAGE_SIZE for all devicesAdrian Schmutzler2019-07-251-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes IMAGE_SIZE for all devices based on the partition size given in DTS: DEVICE *.MK *.DTS VERDICT 7links_px-4885-4m (4M) 0x3b0000 7links_px-4885-8m - 0x7b0000 default 8devices_carambola - 0x7b0000 default accton_wr6202 - 0x7b0000 default airlive_air3gii (4M) 0x3b0000 alfa-network_w502u - 0x7b0000 default allnet_all0256n-4m (4M) 0x3b0000 allnet_all0256n-8m - 0x7b0000 default allnet_all5002 32448k 0x1fb0000 allnet_all5003 32448k 0x1fb0000 alphanetworks_asl26555-16m 15872k 0xf80000 alphanetworks_asl26555-8m 7744k 0x790000 arcwireless_freestation5 - 0x7b0000 default argus_atp-52b 7808k 0x7a0000 asiarf_awapn2403 (4M) 0x3b0000 asiarf_awm002-evb-4m (4M) 0x3b0000 asiarf_awm002-evb-8m - 0x7b0000 default asus_rt-g32-b1 (4M) 0x3b0000 asus_rt-n10-plus (4M) 0x3b0000 asus_rt-n13u - 0x7b0000 default asus_wl-330n (4M) 0x3b0000 asus_wl-330n3g (4M) 0x3b0000 aximcom_mr-102n - 0x790000 wrong aztech_hw550-3g - 0x7b0000 default belkin_f5d8235-v2 7744k 0x790000 belkin_f7c027 7616k 0x770000 buffalo_whr-g300n 3801088 0x3a0000 dlink_dap-1350 7488k 0x750000 dlink_dcs-930 (4M) 0x3b0000 dlink_dcs-930l-b1 (4M) 0x3b0000 dlink_dir-300-b1 (4M) 0x3b0000 dlink_dir-300-b7 (4M) 0x7b0000 wrong dlink_dir-320-b1 - 0x7b0000 default dlink_dir-600-b1 (4M) 0x3b0000 dlink_dir-610-a1 (4M) 0x3b0000 dlink_dir-615-d (4M) 0x3b0000 dlink_dir-615-h1 (4M) 0x3b0000 dlink_dir-620-a1 - 0x7b0000 default dlink_dir-620-d1 - 0x7b0000 default dlink_dwr-512-b 7800k 0x7e0000 wrong easyacc_wizard-8800 - 0x7b0000 default edimax_3g-6200n 3648k 0x390000 edimax_3g-6200nl 3648k 0x390000 engenius_esr-9753 (4M) 0x3b0000 fon_fonera-20n - 0x7b0000 default hame_mpr-a1 (4M) 0x3b0000 hame_mpr-a2 - 0x7b0000 default hauppauge_broadway 7744k 0x790000 hilink_hlk-rm04 - 0x3b0000 wrong hootoo_ht-tm02 - 0x7b0000 default huawei_d105 (4M) 0x3b0000 huawei_hg255d 15744k 0xf60000 intenso_memory2move - 0x7b0000 default jcg_jhr-n805r (4M) 0x3b0000 jcg_jhr-n825r (4M) 0x3b0000 jcg_jhr-n926r (4M) 0x3b0000 mofinetwork_mofi3500-3gn - 0x7b0000 default netcore_nw718 3712k 0x3a0000 netgear_wnce2001 (4M) 0x350000 wrong nexaira_bc2 - 0x7b0000 default nexx_wt1520-4m (4M) 0x3b0000 nexx_wt1520-8m - 0x7b0000 default nixcore_x1-16m 16064k 0xfb0000 nixcore_x1-8m 7872k 0x7b0000 olimex_rt5350f-olinuxino - 0x7b0000 default olimex_rt5350f-olinuxino-evb - 0x7b0000 default omnima_miniembplug - 0x7b0000 default omnima_miniembwifi - 0x7b0000 default petatel_psr-680w (4M) 0x3b0000 planex_mzk-dp150n (4M) 0x3b0000 planex_mzk-w300nh2 3648k 0x390000 planex_mzk-wdpr - 0x680000 wrong poray_ip2202 - 0x7b0000 default poray_m3 (4M) 0x3b0000 poray_m4-4m (4M) 0x3b0000 poray_m4-8m - 0x7b0000 default poray_x5 - 0x7b0000 default poray_x8 - 0x7b0000 default prolink_pwh2004 - 0x7b0000 default ralink_v22rw-2x2 (4M) 0x3b0000 sitecom_wl-351 (4M) 0x3b0000 skyline_sl-r7205 (4M) 0x3b0000 sparklan_wcr-150gn (4M) 0x3b0000 teltonika_rut5xx - 0xfb0000 wrong tenda_3g150b (4M) 0x3b0000 tenda_3g300m (4M) 0x3b0000 tenda_w150m (4M) 0x3b0000 tenda_w306r-v2 (4M) 0x3b0000 trendnet_tew-638apb-v2 (4M) 0x3b0000 trendnet_tew-714tru - 0x7b0000 default unbranded_a5-v11 (4M) 0x3b0000 unbranded_wr512-3gn-4m (4M) 0x3b0000 unbranded_wr512-3gn-8m - 0x7b0000 default unbranded_xdx-rn502j (4M) 0x3b0000 upvel_ur-326n4g (4M) 0x3b0000 upvel_ur-336un - 0x7b0000 default vocore_vocore-16m 16064k 0xfb0000 vocore_vocore-8m 7872k 0x7b0000 wansview_ncs601w - 0x7b0000 default wiznet_wizfi630a (16M) 0xfb0000 zorlik_zl5900v2 - 0x7b0000 default zyxel_keenetic (4M) 0x3b0000 zyxel_keenetic-start (4M) 0x3b0000 zyxel_nbg-419n (4M) 0x3b0000 zyxel_nbg-419n-v2 (8M) 0x7b0000 No verdict means that the device is correctly set. Legend: ( ): Value is set via ralink_default_fw_size_xxM [ ]: Value is derived from parent definition - : Value is not set and derived from default definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt288x,rt3883: fix IMAGE_SIZE for all devicesAdrian Schmutzler2019-07-252-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes IMAGE_SIZE for all devices based on the partition size given in DTS: DEVICE *.MK *.DTS VERDICT airlink101_ar670w (4M) 0x3c0000 wrong airlink101_ar725w - 0x3B0000 wrong asus_rt-n15 (4M) 0x3b0000 belkin_f5d8235-v1 7744k 0x7b0000 wrong buffalo_wli-tx4-ag300n (4M) 0x3b0000 buffalo_wzr-agl300nh (4M) 0x3b0000 dlink_dap-1522-a1 3801088 0x3a0000 ralink_v11st-fe (4M) 0x003b0000 asus_rt-n56u - 0x007b0000 default belkin_f9k1109v1 7224k 0x7a0000 wrong dlink_dir-645 - 0x7b0000 default edimax_br-6475nd 7744k 0x00790000 loewe_wmdr-143n - 0x7b0000 default omnima_hpm 16064k 0x00fb0000 samsung_cy-swr1100 - 0x7b0000 default sitecom_wlr-6000 7244k 0x713000 trendnet_tew-691gr - 0x007b0000 default trendnet_tew-692gr - 0x007b0000 default No verdict means that the device is correctly set. Legend: ( ): Value is set via ralink_default_fw_size_xxM [ ]: Value is derived from parent definition - : Value is not set and derived from default definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt76x8: fix IMAGE_SIZE for all devicesAdrian Schmutzler2019-07-251-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes IMAGE_SIZE for all devices based on the partition size given in DTS: DEVICE *.MK *.DTS VERDICT alfa-network_awusfree1 (8M) 0x7b0000 buffalo_wcr-1166ds - 0x7c0000 wrong cudy_wr1000 (8M) 0x7b0000 d-team_pbr-d1 (16M) 0x0fb0000 duzun_dm06 - 0x7b0000 default glinet_gl-mt300n-v2 16064k 0xfb0000 glinet_vixmini 7872k 0x7b0000 hilink_hlk-7628n (32M) 0x1fb0000 hiwifi_hc5661a (16M) 0xf70000 wrong hiwifi_hc5861b 15808k 0xf70000 mediatek_linkit-smart-7688 (32M) 0x1fb0000 mediatek_mt7628an-eval-board (4M) 0x7b0000 wrong mercury_mac1200r-v2 - 0x7c0000 wrong netgear_r6120 15744k 0xf60000 onion_omega2 (16M) 0xfb0000 onion_omega2p (32M) 0x1fb0000 rakwireless_rak633 - 0x7b0000 default skylab_skw92a 16064k 0xfb0000 tama_w06 15040k 0xeb0000 totolink_lr1200 7872k 0x7b0000 tplink_archer-c20-v4 7808k 0x7a0000 tplink_archer-c50-v3 7808k 0x7a0000 tplink_archer-c50-v4 7616k 0x770000 tplink_tl-mr3020-v3 7808k 0x7a0000 tplink_tl-mr3420-v5 7808k 0x7a0000 tplink_tl-wa801nd-v5 7808k 0x7a0000 tplink_tl-wr802n-v4 7808k 0x7a0000 tplink_tl-wr840n-v4 7808k 0x7a0000 tplink_tl-wr840n-v5 3904k 0x3d0000 tplink_tl-wr841n-v13 7808k 0x7a0000 tplink_tl-wr841n-v14 3968k 0x3e0000 tplink_tl-wr842n-v5 7808k 0x7a0000 tplink_tl-wr902ac-v3 7808k 0x7a0000 unielec_u7628-01-128m-16m 16064k 0xfb0000 vocore_vocore2 (16M) 0xfb0000 vocore_vocore2-lite (16M) 0x7b0000 wrong wavlink_wl-wn570ha1 (8M) 0x7b0000 wavlink_wl-wn575a3 (8M) 0x7b0000 widora_neo-16m (16M) 0x0fb0000 widora_neo-32m (32M) 0x1fb0000 wiznet_wizfi630s (32M) 0x1fb0000 wrtnode_wrtnode2p (16M) 0x1fb0000 wrong wrtnode_wrtnode2r (16M) 0x1fb0000 wrong xiaomi_mir4a-100m 14976k 0xea0000 xiaomi_miwifi-nano (16M) 0xfb0000 zbtlink_zbt-we1226 (8M) 0x7b0000 zyxel_keenetic-extra-ii 14912k 0xe90000 No verdict means that the device is correctly set. Legend: ( ): Value is set via ralink_default_fw_size_xxM [ ]: Value is derived from parent definition - : Value is not set and derived from default definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-10 22:25:25 +0000