aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SKPetr Štetiar2018-11-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory OpenWrt image it's referenced as BDCOM WAP2100-SK device. Specifications: - SoC: MediaTek MT7620A - RAM: 128 MB - Flash: 16 MB - Ethernet: 5 FE ports - Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported) - UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config - LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G - Other: USB port, SD card slot and 2x external antennas (non-detachable) Flashing instructions: A) The U-Boot has HTTP based firmware upgrade A1) Flashing notes We've identified so far two different batches of units, unfortunately each batch has different U-Boot bootloader flashed with different default environment variables, thus each batch has different IP address for accessing web based firmware updater. * First batch has web based bootloader IP address 1.1.1.1 * Second batch has web based bootloader IP address 192.168.1.250 In case you can't connect to either of those IPs, you can try to get the default IP address via two methods: A1.1) Serial console, then the IP address is visible during the boot ... HTTP server is starting at IP: 1.1.1.1 raspi_read: from:40004 len:6 HTTP server is ready! ... A1.2) Over telnet/SSH using this command: root@bdcom:/# grep ipaddr= /dev/mtd0 ipaddr=1.1.1.1 A2) Flashing with browser * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask * Reboot the device and try to reach web based bootloader in the browser with the following URL http://1.1.1.1 * Quickly select the firmware sysupgrade file and click on the `Update firmware` button, this all has to be done within 10 seconds, bootloader doesn't wait any longer If done correctly, the web page should show UPDATE IN PROGRESS page with progress indicator. Once the flashing completes (it takes roughly around 1 minute), the device will reboot to the OpenWrt firmware A3) Flashing with curl sudo ip addr add 1.1.1.2/24 dev eth0 curl \ --verbose \ --retry 3 \ --retry-delay 1 \ --retry-max-time 30 \ --connect-timeout 30 \ --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \ http://1.1.1.1 Now power on the router. B) The U-boot is based on Ralink SDK so we can flash the firmware using UART. 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX) 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix ethernet for f5d8235-v2 boardRoman Yeryomin2018-11-261-0/+1
| | | | | | | | | Belkin F5D8235 v2 has two ethernet switches on board. One internal rt3052 and rtl8366rb on rgmii interface. Looks like internal switch settings were lost in translation to device tree infrastructure. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: add support for Skylab SKW92A in EVBRussell Senior2018-11-261-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifically, SKW92A_E16, described here: http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x u.FL - Power by micro-USB connector at USB1 on EVB - UART via micro-USB connector at USB3 on EVB (57600 8n1) - 5x Ethernet LEDs - 1x WLAN LEDs - 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next to daughter board on EVB - WPS/Reset button (S2 on EVB) - RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board Flash instruction: >From Skylab firmware: 1. Associate with SKYLAP_AP 2. In a browser, load: http://10.10.10.254/ 3. Username/password: admin/admin 4. In web admin interface: Administration / Upload Firmware, browse to sysupgrade image, apply, flash will fail with a message: Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data! 5. Telnet to 10.10.10.254, drops you into a root shell with no credentials 6. # cd /var 7. # mtd_write -r write tmpFW mtd4 Unlocking mtd4 ... Writing from tmpFW to mtd4 ... [e] 8. When flash has completed, you will have booted into your firmware. >From U-boot via TFTP and initramfs: 1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server 2. Connect to serial console at USB3 on EVB 3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "1" 7. At u-boot prompts: Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin 8. Move ethernet to port 0 (WAN) on EVB 9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash with sysupgrade. >From U-boot via TFTP direct flash: 1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server 2. Connect to serial console at USB3 on EVB (57600 8N1) 3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "2" 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin 8. When transfer is complete or as OpenWrt begins booting, move ethernet to port 0 (WAN). Signed-off-by: Russell Senior <russell@personaltelco.net>
* ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3Daniel Golle2018-11-252-1/+2
| | | | | | | | | Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio which wasn't supported at the time the devices were added to OpenWrt. Now that we got it, include kmod-mt76x0e in images for those devices. Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix netgear r6120 factory image generationKoen Vandeputte2018-11-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | as indicated in commit c5bf408ed6bd "(ramips: fix image generation for mt76x8") more rework was needed to fix the other issues. Building on another machine, but using the same arch, showed the application failing again for different reasons. Fix this by completely rewriting the application, fixing following found issues: - buffer overflows, resulting in stack corruption - flaws in memory requirement calculations (too small, too large) - memory leaks - missing bounds checking on string handling - non-reproducable images, by using unitilized memory in checksum calculation - missing error handling, resulting in succes on specific image errors - endianness errors when building on BE machines - various minor build warnings - documentation did not match the code actions (header item locations) - allowing input to be decimal, hex or octal now Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-162-30/+30
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: fix Archer C20 sysupgradeSteffen Förster2018-09-261-1/+0
| | | | | | | | | | The sysupgrade image failed the check due to the wrong string in the supported devices. This patch provides the correct name by dropping the SUPPORTED_DEVICES to use the default generated name. Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net> [drop the SUPPORTED_DEVICES, the old name was never used in a release] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: ex2700: actually remove kmod-mt76*Joseph C. Lehner2018-09-261-1/+1
| | | | | | | | | | | | | | When building using the multiple devices option with per-device root filesystem, only the meta package mt76 is omitted but not the dependencies selected by the package. Explicitly exclude all 3 mt76 packages, plus the metapackage. Otherwise, these modules will be included in the build, wasting a few hundred kilobytes. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [mention the root cause of the issue in the commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link TL-MR3020 v3Carlo Nel2018-09-061-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N. This PR is based on the work of @meyergru[1], with his permission. Specification: - MediaTek MT7628N/N (575 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet Flash instruction: The only way to flash the image in TL-MR3020 v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. [1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3 Signed-off-by: Carlo Nel <carlojnel@gmail.com>
* ramips: only limit lzma dictionary size on mt7621Jo-Philipp Wich2018-08-302-1/+2
| | | | | | | | | | | | | The changed dictionary size leads to a different LZMA header which breaks sysupgrade image magic checkibng on at least some RT288x boards. Since the commit message only mentions testing on MT7621 and since the change appears to break at least one other ramips subtarget, do not take any chances and restrict the size limitation to only MT7621. Fixes FS#1797 Fixes 09b6755946 ("ramips: limit dictionary size for lzma compression") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for ELECOM WRC-1900GSTNOGUCHI Hiroshi2018-08-231-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-151-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for HiWiFi HC5861Bold-masterDeng Qingfang2018-08-141-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN https://www.hiwifi.com/enjoy-view Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7612EN 802.11ac 2T2R 867Mbps - 5x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Everything is working Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add missing USB packages into ASL26555-16MZoltan HERPAI2018-08-131-1/+1
| | | | | | | Mirror the package list from the 8M device profile to the 16M device profile. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-131-3/+3
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear R6120Ludwig Thomeczek2018-08-131-0/+28
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6120, aka Netgear AC1200. Specification: - SoC: MediaTek MT7628 (580 MHz) - Flash: 16 MiB - RAM: 64 MiB - Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E) - LAN speed: 10/100 - LAN ports: 4 - WAN speed: 10/100 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 To flash use nmrpflash with the provided factory.img. Flashing via webinterface will not work, for now. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ath79: add support for I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2018-08-111-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Edimax BR-6478AC v2Daniel Gimpelevich2018-08-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie. Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated. Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Macronix MX25L6405D - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7612E 5GHz 802.11ac - Switch: Mediatek MT7530W Gigabit Switch - USB: Yes 1 x 2.0 Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 4. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: add support for ELECOM WRC-2533GSTINAGAKI Hiroshi2018-07-301-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - MT7621A (2-Core, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 4T4R 2.4/5 GHz wifi - MediaTek MT7615 - 5x 10/100/1000 Mbps Ethernet - 4x LEDs, 6 keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-2533GST 2. Connect power cable to WRC-2533GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mmc: Add SD card support to HC5661ALoveSy2018-07-301-0/+1
| | | | | | | | | | Tested on HC5661A and it now fixes the issue that when enabling sd card in HC5661A, the wan and 3 lan ports will down. Known issue: - When enabling SD card support, the led light of system will down and the rest 2 lights keep working. Signed-off-by: LoveSy <shana@zju.edu.cn>
* ramips: define common MikroTik RouterBOARD image recipeThibaut VARÈNE2018-07-191-11/+9
| | | | | | | | | | All these devices share the exact same image format. The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie slot like its bigger sibling. The usb kmod is necessary for usb-over-pcie support, which is mandatory for a lot of LTE modules. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: TP-Link TL-WR902AC v3: don't build factory imagePeter Lundkvist2018-07-121-1/+0
| | | | | | | | | | | | | | | | | | | | | The line that produces factory image was accidentally left by me while testing before inital commit. I came to the conclusion that flashing from OEM firmware does not work (seems to share this behavior with other tplinks based on mt7628). I have not done any further analysis, as I was unable to open the case and attach a serial port (too much glue). Maybe i will try once more. So the way to do initial flashing (or un-bricking) is to use the tftp-recover image. It is possible to revert to OEM firmware with tftp recovery; in this case the first 512 bytes the image file need to be cut off. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com> [add explaination provided via mail as commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Blueendless Kimax U35WFAdemar Arvati Filho2018-07-071-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908 Based on: https://github.com/lede-project/source/pull/965 Specification: - SoC: MediaTek MT7620N - CPU/Speed: 580 MHz - Flash-Chip: KH25L12835F Spi Flash - Flash size: 16 MiB - RAM: 64 MiB - LAN: 1x 100 Mbps Ethernet - WiFi SoC-integrated: 802.11bgn - 1x USB 2.0 - UART: for serial console Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 3. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* ramips: add support for I-O DATA WN-AX1167GRINAGAKI Hiroshi2018-07-071-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Stock firmware: In the stock firmware, WN-AX1167GR has two os images each composed of Linux kernel and rootfs. These images are stored in "Kernel" and "app" partition of the following partitions, respectively. (excerpt from dmesg): MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" The flag for boot partition is stored in "Key" partition, and U-Boot reads this and determines the partition to boot. If the image that U-Boot first reads according to the flag is "Bad Magic Number", U-Boot then tries to boot from the other image. If the second image is correct, change the flag to the number corresponding to that image and boot from that image. (example): ## Booting image at bc800000 ... Bad Magic Number,FFFFFFFF Boot from KERNEL 1 !! ## Booting image at bc060000 ... Image Name: MIPS OpenWrt Linux-4.14.50 Image Type: MIPS Linux kernel Image (lzma compressed) Data Size: 1865917 Bytes = 1.8 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK raspi_erase_write: offs:f90000, count:34 . . Done! Starting kernel ... Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AX1167GR 2. Connect power cable to WN-AX1167GR and turn on it 3. Access to "192.168.0.1" on the web browser and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and perform firmware update 5. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR 6. Wait ~180 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for TL-WA801ND v5Romain MARIADASSOU2018-07-041-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MediaTek MT7628NN - CPU/Speed: 580 MHz - Flash-Chip: ELM Technology GD25Q64 - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn Currently the only method to install openwrt for the first time is via TFTP recovery. After first install you can use regular updates. Flash instructions: 1) To flash the recovery image, start a TFTP server with IP address 192.168.0.66 and serve the recovery image named tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS and Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds or until the lock LED is lighting up. It will try to download the recovery image and flash it. It can take up to 2-3 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
* ramips: add support for ZyXEL Keenetic Extra IIMaxim Anisimov2018-07-041-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7628N/N - CPU/Speed: 580 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (57600 8n1) - Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn - Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac - USB: Yes 1 x 2.0 - 4x LED, 3x button The device supports dual boot mode. So we use only first half of flash. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin" to "kextra2_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: move zyimage define to common MakefileMaxim Anisimov2018-07-042-4/+4
| | | | Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for MikroTik RouterBOARD RBM11gTobias Schramm2018-07-041-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik RouterBOARD RBM11g. =Hardware= The RBM11g is a mt7621 based device featuring one GbE port and one miniPCIe slot with a sim card socket and USB 2.0. ==Switch== The single onboard Ethernet port is connected the CPU directly. The internal switch of the mt7621 SoC is disabled. ==Flash== The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS connected to CS0. ==PCIe== The board features a single miniPCIe slot. It has a dedicated mini SIM socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via GPIO9. ==USB== There are no external USB ports. ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack (center-positive). The input voltage range is 11-32 V. ==Serial port== The device does have an onboard UART on an unpopulated header next to the flash chip: GND: pin 2 TX: pin 7 RX: pin 6 Settings: 115200, 8N1 See below illustration for positioning of the header. 0 = screw hole * = some pin T = TX pin R = RX pin G = GND pin Pinout: +--------------- |O | __ | / \ | \__/ | | | | +---+ | |RAM| | +--+ | | | |**| <- unpopulated header with UART | |*T| +---+ | |R*| +--------+ | |**| | | | |G*| | CPU | | +--+ | | | +--+ | | | | | +--------+ | +--+ <- flash chip |O | +-----+ | | | |+--+ | | || | | | +--------------------- =Installation= To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM11G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** When rebooted the board will try booting via ethernet first. If your board does not boot via ethernet automatically you will have to attach to the serial port and set ethernet as boot device within RouterBOOT. 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" initramfs image 2. Connect to ethernet port on board 3. Power on the board 4. Wait for OpenWrt to boot Right now OpenWrt will be running with a SSH server listening. Now OpenWrt must be flashed to the devices flash: 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" Once the flashing completes the board will reboot. Disconnect from the devices ethernet port or stop the DHCP/TFTP server to prevent the device from booting via ethernet again. The device should now boot straight to OpenWrt. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: limit dictionary size for lzma compressionFelix Fietkau2018-07-031-1/+1
| | | | | | | | | | | | In some cases, recent builds fail to boot from flash with at least some MT7621 based devices. The error message is: "LZMA ERROR 1 - must RESET board to recover" Booting the same kernel via TFTP works for some reason. Through testing I figured out that limiting the LZMA dictionary size seems to prevent these errors Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: RE350: add rootfs offset to headerAlex Maclean2018-06-261-1/+1
| | | | | | | Have mktplinkfw fill in the rootfs offset so the firmware splitter can find it without aligning to erase blocks. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for TP-Link Archer C2Franz Flasch2018-06-251-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Winbond 25Q64BVSIG - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac - Switch: RTL8367RB Gigabit Switch - USB: Yes 1 x 2.0 Preparing a TFTP recovery image for initial flashing: Currently the only method to install openwrt for the first time is via TFTP download in u-boot. After first install you can use regular updates. WARNING: This method also overwrites the bootloader partition! Create a TFTP recovery image: 1) Download a stock TP-Link Firmware file here: https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware 2) Extract u-boot from the binary file: #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072 3) Now merge the sysupgrade image and the u-boot into one binary: #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin The resulting image can be flashed via TFTP recovery mode. Flash instructions: 1) To flash the recovery image, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC2V1_tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS/Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds. It will try to download the recovery image and flash it. It can take up to 20-25 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: Add support for Phicomm K2GChuanhong Guo2018-06-211-0/+8
| | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Add support for Mikrotik RouterBOARD RBM33gTobias Schramm2018-06-211-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik RouterBOARD RBM33g. =Hardware= The RBM33g is a mt7621 based device featuring three gigabit ports, 2 miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male onboard RS-232 serial port. Additionally there are a lot of accessible GPIO ports and additional buses like i2c, mdio, spi and uart. ==Switch== The three Ethernet ports are all connected to the internal switch of the mt7621 SoC: port 0: Ethernet Port next to barrel jack with PoE printed on it port 1: Innermost Ethernet Port on opposite side of RS-232 port port 2: Outermost Ethernet Port on opposite side of RS-232 port port 6: CPU ==Flash== The device has two spi flash chips. The first flash chips is rather small (512 kB), connected to CS0 by default and contains only the RouterBOOT bootloader and some factory information (e.g. mac address). The second chip has a size of 16 MB, is by default connected to CS1 and contains the firmware image. ==PCIe== The board features three PCIe-enabled slots. Two of them are miniPCIe slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2). Each of the miniPCIe slots is connected to a dedicated mini SIM socket on the back of the board. Power to all three PCIe-enabled slots is controlled via GPIOs on the mt7621 SoC: PCIe0: GPIO9 PCIe1: GPIO10 PCIe2: GPIO11 ==USB== The board has one external USB 3.0 port at the rear. Additionally PCIe port 0 has a permanently enabled USB interface. PCIe slot 1 shares its USB interface with the rear USB port. Thus only either the rear USB port or the USB interface of PCIe slot 1 can be active at the same time. The jumper next to the rear USB port controls which one is active: open: USB on PCIe 1 is active closed: USB on rear USB port is active ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack. The input voltage range is 11-32 V. =Installation= ==Prerequisites== A USB -> RS-232 Adapter and a null modem cable are required for installation. To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM33G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** Serial settings: 115200 8N1 The installation is a two-step process. First the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted via tftp: 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" initramfs image 2. Connect to WAN port (left side, next to sys-LED and power indicator) 3. Connect to serial port of board 4. Power on board and enter RouterBOOT setup menu 5. Set boot device to "boot over ethernet" 6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server allows dynamic bootp) 6. Save config 7. Wait for board to boot via Ethernet On the serial port you should now be presented with the OpenWRT boot log. The next steps will install OpenWRT persistently. 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" Once the flashing completes reboot the router and let it boot from flash. It should boot straight to OpenWRT. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add lzma-loader targetsTobias Schramm2018-06-211-0/+16
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add support for mt7621 to lzma-loaderTobias Schramm2018-06-215-18/+60
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: add support for ELECOM WRC-1167GHBK2-SINAGAKI Hiroshi2018-06-191-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-161-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-081-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek MT7621S. Specification: - MT7621S (1-Core, 2-Threads) - 64 MB of RAM - 8 MB of Flash (SPI) - 2T2R 2.4 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR" and place it in the TFTP directory 3. Set the IP address of the computer to 192.168.99.8, connect to the LAN port of WN-GX300GR, and start the TFTP server on the computer 4. Connect power cable to WN-GX300GR and turn on the router 5. Press "1" key on the serial console to interrupt boot process on U-Boot, press Enter key 3 times and start firmware download via TFTP 6. WN-GX300GR downloads initramfs image and boot with it 7. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-GX300GR 8. Wait ~150 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Use generic board detect for GnuBee devicesRosen Penev2018-05-301-2/+2
| | | | | | | | | | | This is a port of an old commit from mkresin's tree: 09260cdf3e9332978c2a474a58e93a6f2b55f4a8 This has the potential to break sysupgrade but it should be fine as there is no stable release of LEDE or OpenWrt that support these devices. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for YUKAI Engineering Inc. BOCCOYuheiOKAWA2018-05-181-0/+7
| | | | | | | | | | | | | BOCCO is a communication robot provided by YUKAI Engineering Inc. SoC: MT7620A MEM: 256MB Flash: 8MB NAND: 512MB (non support) Include Sound DAC and AMP. No Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
* ramips: add support for mqmaker witi 512mb versionDavide Ammirata2018-05-071-4/+15
| | | | | | | | | | | | Splitted out the dts file and create the new dts for the 256 MByte RAM and the 512 MB RAM version. Migrate both versions to the common board detection. The install the 512 MByte Version on a board running the 256 MByte image, a forceful sysupgrade with the -F flag is required. Signed-off-by: Davide Ammirata <list@davidea.it>
* ramips: add support for Ravpower WD03Matthias Badaire2018-05-071-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RavPower WD03 is a battery powered SD card reader and a USB port. Specifications: SOC: MediaTek MT7620N BATTERY: 6000mah WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: PM Tech PMD708416CTR-5CN 32 MB FLASH: Holtek HT66F40 - 8 MB Flash LED: Power button and 4 leds to indicate power level of the battery (could not get control of that) INPUT: Power, reset button OTHER: USB SD-Card reader with card detect on GPIO#42 Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Installation: - Download the sysupgrade image - Place it in the root of a clean TFTP server running on your computer. - Rename the image to "kernel" — be sure there is no file extension. - Plug the WD03 into your computer via ethernet. - Set your computer to use 10.10.10.254 as its IP address. - With your WD03 shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254 and install the kernel file. Once it has finished installation of the kernel file, it will search for a (nonexistent) rootfs file — when it begins searching for this file, shut down the WD03 by holding the power button normally. - Start up your WD03 normally. Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
* ramips: create image for mt7628 evb boardMathias Kresin2018-04-231-0/+1
| | | | | | | The image for the EVB board got lost with the merge of the mt7628 and mt7688 subtargets. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use patch-dtb for F5D8235 V1Tobias Wolf2018-04-231-3/+1
| | | | | | | | | | The old DTB method (OWRTDTB) is not recognized by the boot process anymore with 4.9/4.14. This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel image. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-2/+2
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zorlik ZL5900V2Vianney le Clément de Saint-Marcq2018-04-081-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2. It is marketed as "3G Wi-Fi Router". Only the PCB has the model name "ZL5900V2" printed on it. Specifications: - Ralink RT5350F (360 MHz) - 32 MB RAM - 8 MB Flash - 802.11bgn 1T1R - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (Type-A) - 5200 mAh battery The ramdisk image (not the squashfs sysupgrade image) can be flashed through the web interface (named "GoAhead") of the factory firmware. However, as the factory firmware does not cleanly unmount the rootfs before flashing, the device may hang instead of rebooting after successful write. Power cycling the device gets you in OpenWrt where the squashfs image may be flashed through normal sysupgrade procedure. Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
* ramips: add support for the YouHua WR1200JSZheng Qian2018-04-081-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan) and 1 USB 2.0 port. Devices is base on MediaTek MT7621AT + MT7603E + MT7612E. Specification: - MT7612AT (880 MHz) - 128 MB of RAM - 16 MB of FLASH (SPI NOR) - 5x 10/100/1000 Mbps Ethernet - 2T2R 2.4 GHz (MT7603E) - 2T2R 5 GHz (MT7612E) - 1x USB 2.0 - 10x LED (Power 2G 5G WPS Internet LAN4-1 USB) - 3x button (reset wifi wps) - DC jack for main power input (12V) Installation: 1.) Press reset key 5 sec and restore the factory default 2.) Login webUI and change username to root and set a new password 3.) Visit http://192.168.2.254/adm/telnetd.shtml and turn on the telnet service 4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin to a usb pan 5.) Plug the usb pan to the router, telnet to the router and login by root 6.) cd /media/sda1 and check the initramfs file is there 7.) exec command: mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel 8.) reboot and visit 192.168.1.1 Signed-off-by: Zheng Qian <sotux82@gmail.com>
* ramips: add dwr-512 jboot firmware configurationGiuseppe Lippolis2018-04-081-3/+11
| | | | | | | | | | | | | | | | | | | | | The previous fw version require the replacement of the stock bootloader with u-boot. This prevent an easy stock restore of the original fw. Now a proper fw util has been developed to manage the stock jboot bootloader. Therefore make sense have a fw image for the stock bootloader. The old fw configuration (u-boot) is not compatible with the new one and will not be supported anymore. So at the end 2 image can be generated: 1) factory image with jboot bootloader openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin 2) sysupgrade image with jboot bootloader openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: add U-Boot env support for ALFA Network AC1200RMPiotr Dymacz2018-04-061-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 00:51:19 +0000