aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for Ubiquiti UniFi nanoHDDavid Bauer2020-03-101-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621AT WiFi: MediaTek MT7603 bgn 2T2R MediaTek MT7615 ac 4T4R Flash: 32M SPI (Macronix MX25L25635F) RAM: 128M DDR3 (Winbond W631GG6KB) LED: Dome (Blue / White) BTN: Reset Installation ------------ These instructions were written for firmware version v3.9.27. Downgrade if necessary. 1. Copy the OpenWrt sysupgrade image to the devices /tmp folder via scp. On factory defaults, user and password is "ubnt" at 192.168.1.20/24. 2. Write the bootselect flag. Otherwise, the device might boot from the wrong partition. Verify the mtd partition used in the command below is the one labled "bs" in /proc/mtd (as this might change in the future). > dd if=/dev/zero bs=1 count=1 of=/dev/mtd4 3. Write the OpenWrt sysupgrade to the mtd partitions labled "kernel0" and "kernel1". > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6 > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7 4. Reboot or powercycle the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link RE210 v1Christoph Krapp2020-03-091-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7620A RAM: 64MB FLASH: 8MB SPI WLAN: 2G: MediaTek MT7620A 5G: MediaTek MT7610EN ETH: 1x 10/100/1000M (Atheros AR8035) LED: RSSI (orange/green) WiFi 2G (green) WiFi 5G (green) Power (green) System (red / green) BTN: Power Reset LED WPS Serial ------ P1 - Tx P2 - Rx P3 - GND P4 - VCC Pin 4 is the one closest to the LAN port. MAC overview ------------ WAN *:4c uboot 0x1fc00 2.4 *:4c uboot 0x1fc00 5 *:4e uboot 0x1fc00 +2 Installation ------------ Web interface: It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial/TFTP: You can use initramfs for booting via RAM or flash the image directly. Additional Notes: If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. In order to flash back to stock, the first header and U-Boot needs to be stripped from the original firmware. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [change rssi LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-041-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-041-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: disable images for Netgear 2700Petr Štetiar2020-03-021-0/+1
| | | | | | Because openwrt-ramips-mt7620-netgear_ex2700-squashfs-factory.bin is too big. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: append tail to WF2881 initramfs imageSungbo Eo2020-02-111-0/+8
| | | | | | | | | | | | Stock firmware has a vendor-defined tail at the end of uImage for image validation. This patch enables OpenWrt installation from stock firmware without having to access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix device name of netis WF-2881 to WF2881Sungbo Eo2020-02-071-4/+3
| | | | | | | | | | | The correct model name of WF-2881 is WF2881 without hyphen. The former used boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the sysupgrade-tar image, which is newly added in the previous commit, should not be used to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-071-2/+4
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-051-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-051-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: extend and rename wr1201-factory-headerINAGAKI Hiroshi2020-02-051-14/+16
| | | | | | | | | | | | | | | | | | | | | This commit adds the ability to set custom uImage magic to Build/wr1201-factory-header and renames it to "Build/custom-initramfs-uimage". Custom uImage header in initramfs image is required on following devices: - I-O DATA WN-AX1167GR2 - I-O DATA WN-AX2033GR - I-O DATA WN-AX2033GR2 - I-O DATA WN-DX1167R While at it, fix typo in comment. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> [shorten commit title, minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-011-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: collect and harmonize TP-Link image variants in common fileAdrian Schmutzler2020-02-014-114/+100
| | | | | | | | | | | | This moves the various variants of common device definitions for TP-Link devices to a common Makefile common-tp-link.mk. This provides the opportunity to reorganize and move parameters between individual device definitions and the common ones. While at it, also use the common definitions for previously independent definitions where appropriate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20iAdrian Schmutzler2020-01-291-1/+0
| | | | | | | | | DEVICE_PACKAGES is specified twice for the same device. Remove the first (=older) assignment. Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for GL.iNet microuter-N300David Bauer2020-01-291-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a pocket-size travel router. It is essentially identical to the VIXMINI (internally referred as MT300N-v3) but with double the RAM and SPI-flash. Additionally, set the label-mac for both the VIXMINI as well as the microuter-N300. Hardware -------- SoC: MediaTek MT7628NN RAM: 128M DDR2 FLASH: 16M LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: define SOC only once for uniform targetsAdrian Schmutzler2020-01-244-114/+7
| | | | | | | | | | | In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have the same value set to the SOC variable for each device individually. This patch introduces a non-device-dependent variable DEFAULT_SOC, which is used if no specific SOC is set for a device, and thus reduces the number of redundant definitions drastically. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-181-0/+24
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
* ramips: mt7621: disable images for gehua_ghl-r-001Petr Štetiar2020-01-141-0/+1
| | | | | | | | | | This device OOPs during the boot due to broken flash. It can be probably fixed with `broken-flash-reset` once ramips is on 4.19 kernel. So disable images for this device until its fixed. Ref: FS#2695, PR#2483 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for TP-Link Archer C20 v5Maxim Anisimov2020-01-091-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v5 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Create Factory image -------------------- As all installation methods require a U-Boot to be integrated into the Image (and we do not ship one with the image) we are not able to create an image in the OpenWRT build-process. Download a TP-Link image from their Website and a OpenWRT sysupgrade image for the device and build yourself a factory image like following: TP-Link image: tpl.bin OpenWRT sysupgrade image: owrt.bin > dd if=tpl.bin of=boot.bin bs=131584 count=1 > cat owrt.bin >> boot.bin Installing via Web-UI --------------------- Upload the boot.bin via TP-Links firmware upgrade tool in the web-interface. Installing via Recovery ----------------------- Activate Web-Recovery by beginning the upgrade Process with a Firmware-Image from TP-Link. After starting the Firmware Upgrade, wait ~3 seconds (When update status is switching to 0%), then disconnect the power supply from the device. Upgrade flag (which activates Web-Recovery) is written before the OS-image is touched and removed after write is succesfull, so this procedure should be safe. Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1. When active, all LEDs but the WPS LED are off. Remeber to assign yourself a static IP-address as DHCP is not active in this mode. The boot.bin can now be uploaded and flashed using the web-recovery. Installing via TFTP ------------------- Prepare an image like following (Filenames from factory image steps apply here) > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1 > dd if=tpl.bin of=tmp.bin bs=131584 count=1 > dd if=tmp.bin of=boot.bin bs=512 skip=1 > cat boot.bin >> tp_recovery.bin > cat owrt.bin >> tp_recovery.bin Place tp_recovery.bin in root directory of TFTP server and listen on 192.168.0.66/24. Connect router LAN ports with your computer and power up the router while pressing the reset button. The router will download the image via tftp and after ~1 Minute reboot into OpenWRT. U-Boot CLI ---------- U-Boot CLI can be activated by holding down '4' on bootup. Dual U-Boot ----------- This is TP-Link MediaTek device with a split-uboot feature design like a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via TFTP and HTTP, jumping straight into the second (firmware-uboot) if no recovery needs to be performed. The firmware-uboot unpacks and executed the kernel. Web-Recovery ------------ TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 / TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile" partition before beginning to write and removes it afterwards. If the router boots with this flag set, bootloader will automatically start Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT factory image can be written. By doing the same while performing sysupgrade, we can take advantage of the Web-recovery in OpenWRT. It is important to note that Web-Recovery is only based on this flag. It can't detect e.g. a crashing kernel or other means. Once activated it won't boot the OS before a recovery action (either via TFTP or HTTP) is performed. This recovery-mode is indicated by an illuminated WPS-LED on boot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> [adjust some node names for LEDs in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: disable image build for HiWiFi HC5962David Bauer2020-01-091-0/+2
| | | | | | | | Image builds for the ramips-mt7621 target currently fail with: > WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big Disable this board for now. It can still be built using the SDK. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: move mktplinkfw to tplink-v1-image in image-commands.mkAdrian Schmutzler2020-01-081-19/+2
| | | | | | | | | | | | | | | | | | | | | This move the slightly different target-specific implementations of mktplinkfw from the targets to include/image-commands.mk and renames it to tplink-v1-image. Having a common version will increase consistency between implementation and will complete the tplink build command already present in the new location. Due to the slight differences of the original implementations, this also does some adjustments to the device build commands/variables. This also moves rootfs_align as this is required as dependency. Tested on: - TL-WDR4300 v1 (ath79, factory) - TL-WDR4900 v1 (mpc85xx, sysupgrade) - RE210 v1 (ramips, see Tested-by) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Christoph Krapp <achterin@googlemail.com>
* ramips: add support for ipTIME A8004TYong-hyu Ban2020-01-051-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 256M - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615E - 5GHz: MT7615E - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1 * USB3.0 port - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 - Other info: - J9: Unknown unpopulated header. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe> [do not enable xhci node in DTS which is already enabled in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: reduce lzma dictionary size for D-Link DIR-645Mason Clarke2020-01-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently this device fails to boot with the OpenWrt snapshot images (release images are unaffected). The error message is: "LZMA ERROR 1 - must RESET board to recover". This happens because the kernel image is too big for the bootloader to boot. This commit works around this by decreasing the lzma dictionary size option from the default 23 to 10. Before this change the current OpenWrt snapshot image (uncompressed kernel size 4875139 bytes) failed to boot, while now an even bigger image (kernel 4.19 with snapshot default config; uncompressed kernel size 5162833 bytes) boots just fine. The highest lzma dictionary size option this image booted with was 11. 10 was chosen to have a bit more room for growth. An unavoidable side-effect of this change is that the compressed kernel image will take up more space. Total image size with different dictionary size options: D23 - 3973903 bytes (base) D16 - 4113167 bytes (+3.5% - +139264 bytes) D12 - 4317967 bytes (+8.7% - +344064‬ bytes) D11 - 4383503 bytes (+10.3% - +409600 bytes) D10 - 4461327 bytes (+12.3% - +487424 bytes) Fixes: FS#1484 Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
* ramips: fix sysupgrade image for TP-Link RE200v1Andreas Böhler2020-01-051-1/+1
| | | | | | | Images generated for the TP-Link RE200v1 cannot be updated using sysupgrade, because a necessary call to append-metadata was missing. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for Edimax RA21SMaksym Medvedev2020-01-041-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Edimax RA21S is a dual band 11ac router, based on MediaTek MT7621A and MT7615N chips. Specification: - SoC: MediaTek MT7621A dual-core @ 880MHz - RAM: 256M (Nanya NT5CC128M16IP) - FLASH: 16MB (Macronix MX25L12835F) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) - USB: No - BTN: Reset, WPS - LED: 4 red LEDs, indistinguishable when case closed - UART: through-hole on PCB. J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad Installation: Update the factory image via the OEM web-interface (by default: http://192.168.2.1/) User: admin Password: 1234 The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect via ethernet port 2. Tested on device by @UAb5eSMn Signed-off-by: Maksym Medvedev <redrathnure@gmail.com> [split DTS and take over improvements from RG21S, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE200 v1Andreas Böhler2019-12-311-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN. Specifications -------------- - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled; only 6 supported), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. The 5G LED is currently not supported, since the GPIOs couldn't be determined. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. Additional notes ---------------- MAC address assignment is based on stock-firmware. For me, the device assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G WiFi has a separate MAC with +2. *:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158 *:89 unused userconfig 0x0160 *:8A 5G not present in flash This seems to be the first ramips device with a TP-Link v1 header. The original firmware has the string "EU" embedded, there might be some region- checking going on during the firmware upgrade process. The original firmware also contains U-Boot and thus overwrites the boot loader during upgrade. In order to flash back to stock, the first header and U-Boot need to be stripped from the original firmware. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: rename MTK_SOC to SOCAdrian Schmutzler2019-12-207-321/+320
| | | | | | | This replaces MTK_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-195-227/+235
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A104nsSungbo Eo2019-12-171-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100Mbps - Switch: SoC internal - USB: 1x 2.0 - UART: - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. In contrast to to-be-supported A1004ns, the A104ns has no usable value in 0x1fc40 (uboot), so wan_mac needs to be calculated. Also note that GPIOs for the LEDs really are inverted compared to the A1004ns. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [moved state_default to device DTS, reordered properties in wmac, added comment about wan_mac and LED GPIOs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG JHR-AC876MDENG Qingfang2019-12-131-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JCG JHR-AC876M is an AC2600M router Hardware specs: SoC: MT7621AT 2.4GHz: MT7615N 4x4 @ PCIe0 5GHz: MT7615N 4x4 @ PCIe1 Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB USB 2.0 and 3.0 ports 6 LEDs, 3 of which are connected to SoC GPIO Reset and WPS buttons Flash instructions: Stock to OpenWrt: Upload factory.bin in stock firmware's upgrade page, do not preserve settings OpenWrt to stock: Push and hold the reset button for 5s while power cycling to enter recovery mode; Visit 192.168.1.1 and upload stock firmware MAC addresses map: 0x0004 *:1c wlan2g/wan/label 0x8004 *:20 wlan5g 0xe000 *:1b lan 0xe006 *:1a not used in stock fw Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: allow JCG_MAXSIZE in kiB in Build/jcg-headerAdrian Schmutzler2019-12-132-2/+4
| | | | | | | | | | This allows JCG_MAXSIZE to be specified in kilobytes. This makes this value more consistent and easier comparable with other size variables. This also changes the only occurence of the variable, for Cudy WR1000. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A6ns-MSungbo Eo2019-12-131-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ZIO FREEZIOSungbo Eo2019-12-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7603EN - 5GHz: MT7612EN - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1x 3.0 - UART: - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 Notes: - FREEZIO has almost the same board as WeVO W2914NS v2. - Stock firmware is based on OpenWrt BB. MAC addresses in factory partition: 0x0004: WiFi 2.4GHz (label_mac-8) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-4) 0xe000: LAN (label_mac+1) Installation via web interface: 1. Access web admin page and turn on "OpenWrt UI mode". 2. Flash sysupgrade image through LuCI, with the "Keep settings" option OFF. Revert to stock firmware: 1. Perform sysupgrade with stock image. Make sure to NOT preserve settings. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebase, use mt7621_wevo_w2914ns-v2.dtsi] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove unused DTS variable from DEVICE_VARSAdrian Schmutzler2019-12-121-1/+1
| | | | | | | | | | | | | The DTS variable has been removed in 402138d12dca ("ramips: Derive DTS name from device name in Makefile"), but the DEVICE_VARS entry has been overlooked. Remove it now since we are not using this variable. This must _not_ be backported to 19.07, where the variable is still in use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: set uImage name of WeVO 11AC NAS and W2914NS v2Sungbo Eo2019-11-171-0/+2
| | | | | | | | | | | | | The stock firmware and bootloader only accept uImage with names that match certain patterns. This patch enables OpenWrt installation from stock firmware without having to reflash the bootloader or access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-141-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM, USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support. Specification: - MT7621A (880 MHz) - 256/512 MB of RAM (DDR3) - 16/32+ MB of FLASH (SPI NOR) - optional second SPI flash (8-pin WSON/SOIC) - 1x microSD (SDXC) flash card reader - 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1 - optional 802.3at/af PoE module for WAN - 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V) - 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM) - RTC (TI BQ32002, I2C bus) with backup battery (CR2032) - external hardware watchdog (EM Microelectronic EM6324) - 1x USB 2.0 Type-A - 1x micro USB Type-B for system serial console (Holtek HT42B534) - 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator) - 3x button (reset, user1, user2) - 1x I2C (4-pin, 2.54 mm pitch) header on PCB - 4x SIM (6-pin, 2.00 mm pitch) headers on PCB - 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB - 1x mechanical power switch - 1x DC jack with lock (24 V) Other: - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board has additional logic circuit for M.2 SIM switching. The 'sim-select' will work only if both SIM slots are occupied. Otherwise, always slot with SIM inside is selected, no matter 'sim-select' value. - U-Boot enables power in all three miniPCIe and M.2 slots before loading the kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) - all three miniPCIe slots have additional 5 V supply on pins 47 and 49 - the board allows to install up to two oversized miniPCIe cards (vendor has dedicated MediaTek MT7615N/D cards for this board) - this board has additional logic circuit controlling PERSTn pins inside miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe slots but setting GPIO22 to high allows PERSTn control per slot, using GPIO23-25 (value is inverted) You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100Sungbo Eo2019-11-131-1/+1
| | | | | | | | | CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing in default images. This commit adds it. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [changed commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6130Frederik Noe-Sdun2019-11-081-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. The device seems to use base PCB as EX3700/EX3800, but supporting AC1200 using MT7612E. MAC adresses: 5.0 GHz 0x8004 *:9a 2.4 GHz 0x4 *:9b lan 0x28 *:9b wan 0x2e *:9c Since this is a one-port device, although wan MAC address is set in flash, it is not used in OpenWrt setup. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, extended commit message, tiny DTS style fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips, mt7620: reproducible elecom-header uid/gidPaul Spooren2019-11-061-1/+1
| | | | | | | | | | | | | | | | | | | | | The elecom-header renames the firmware image to v_0.0.0.bin, stores its MD5 sum as v_0.0.0.md5 and tars both files again. Both v_0.0.0 files are created as the build user making it harder to reproduce. This commit sets the owner/group of both files to root by adding extra options to the final tar command. Before: 0 buildbot (101) buildbot (102) 3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin 0 buildbot (101) buildbot (102) 33 2019-11-05 14:43:22.000000 v_0.0.0.md5 After: 0 root (0) root (0) 3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin 0 root (0) root (0) 33 2019-11-05 23:43:08.000000 v_0.0.0.md5 Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: fix MTK_SOC for RT3662 devicesSungbo Eo2019-11-041-6/+6
| | | | | | | | | | | rt3883.mk contains both RT3662 and RT3883 device profiles, but commit 6a104ac77206 set MTK_SOC to rt3883 for all devices. This patch fixes it, and renames dts files accordingly. And SoC compatible strings are also appended in the dts. Fixes: 6a104ac77206 ("ramips/rt288x,rt3883: Name DTS files based on scheme") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ZBT WE1026-HKristian Evensen2019-11-031-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * When binding the USB LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [rebased onto base-files split, minor style fixes, removed use of USB led as power LED] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve common definition for Netgear R6xxx in mt7621.mkAdrian Schmutzler2019-11-031-31/+36
| | | | | | | | | | | | | This patch renames and reassembles the common definition for Netgear R6xxx devices in mt7621.mk. The following goals should be achieved: - Give the node a more generic name instead of adding devices to it - Use the common definition in the (less) similar R6220 node - Include/exclude settings into the common definition so the common node contains the common definitions - Prepare for support of R6700 v2 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2Paul Fertser2019-10-271-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CMIIT ID: 2019AP2581 - SoC: MediaTek MT7621 - Flash: 16MiB NOR SPI (GigaDevice GD25Q128B) - RAM: 128MiB DDR3 (ESMT M15T1G1664A) - Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset INSTALLATION: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware (looks like an illegal OpenWrt fork) won't accept any serial input unless "uart_en" is set to "1". Tricks to force u-boot to use default environment do not help as it's restricted in the same way. With bootloader unlocked the easiest way would be to TFTP the sysupgrade image or to sysupgrade after loading an initramfs one. For porting the flash contents were changed externally with an SPI programmer (after lifting Vcc flash IC pin away from the PCB). Forum thread [0] indicates that this device is identical to "Xiaomi Mi Router 4A Gigabit Edition". [0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ramips: add support for Asus RT-AC65PGabor Varga2019-10-241-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it. On both routers the installation can be done also via SSH: Note: The user/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt factory image via scp: > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.50.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux 6. Reboot the router > reboot Changelog: v3: removed [] from filename, rebased to latest master v2: Rebased to latest master v1: Initial release Signed-off-by: Gabor Varga <vargagab@gmail.com>
* ramips: fix TARGET_DEVICES after UniElec renameAdrian Schmutzler2019-10-212-3/+3
| | | | | | | | | | Device node names were updated, but updating TARGET_DEVICES was overlooked. Fixes: 4408723d42e0 ("ramips: remove RAM size from device name for UniElec devices") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove RAM size from device name for UniElec devicesAdrian Schmutzler2019-10-212-8/+9
| | | | | | | | | | | UniElec devices are the last ones in ramips target still having the RAM size in device name although RAM size is auto-detected. Remove this from device name, compatible, etc., as it's not required and might be misleading to users and developers adding device support copying those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: Alternative name KE 2P for Phicomm K2PRoger Pueyo Centelles2019-10-131-0/+2
| | | | | | | | The Phicomm KE 2P is identical to the already supported Phicomm K2P, renamed for the European market. Use the ALT0 buildroot tags to show both devices. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-064-45/+45
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: apply consistent device name/compatible to ZBT-WE1026-5GAdrian Schmutzler2019-09-291-11/+11
| | | | | | | | | | | All Zbtlink ramips devices except the ZBT-WE1026-5G include the zbt-/ZBT- prefix in their model name. This changes ZBT-WE1026-5G to also follow that scheme. The patch moves some block to keep alphatical order. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-28 00:58:08 +0000