aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7621: fix error message when initramfs is too largeJohn Crispin2015-12-171-1/+1
| | | | | | Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47908
* ralink: drop dummy profile from mt7688John Crispin2015-12-171-2/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47901
* ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)John Crispin2015-12-121-1/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
* ramips: add additional support for MQmaker WiTi boardJohn Crispin2015-12-111-1/+6
| | | | | | | | | | | | | | The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845
* build: fix arch used during dts compilationFelix Fietkau2015-12-101-1/+1
| | | | | | | | | Use kernel arch for dts compilation. Also use Image/BuildDTB to build dts for ramips. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47823
* ramips: fix typo in image makefile (#18712)Felix Fietkau2015-11-241-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47627
* ralink: add support for netis WF-2881John Crispin2015-11-241-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619
* ramips: add support for Youku YK1John Crispin2015-11-241-0/+2
| | | | | | | | | Changes since V1: I resend this patch for current trunk.The former V1 patch is for CC branch. Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47617
* ramips: add support for ZBT WG2626John Crispin2015-11-021-1/+6
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47351
* ramips: add support for Dovado tiny ACJohn Crispin2015-11-021-0/+2
| | | | | | | | | | | | | | | | Add support for Dovado tiny AC wifi router. Soc: mt7620a ram: 64MB flash: 8MB 1x usb 2.0 two gigabit lan ports 5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47348
* ramips: add LinkIt Smart7688 supportJohn Crispin2015-10-191-0/+6
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47203
* ramips: add support for 16MB VoCoreJohn Crispin2015-10-051-1/+11
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47120
* ramips: Add build files for HiWiFi HC5x61 modelsJohn Crispin2015-10-051-0/+6
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Spaces -> Tabs 2: Removed some packages Signed-off-by: Xiaoning Kang <kangxn@163.com> SVN-Revision: 47113
* ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350John Crispin2015-09-141-1/+3
| | | | | | | | This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor. Signed-off-by: Tobias Welz <tw@wiznet.eu> SVN-Revision: 46921
* ramips: add support for Planex DB-WRT01John Crispin2015-09-141-0/+2
| | | | | | | | | | This patch add support for Planex DB-WRT01. DANBOARD route on the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio. DANBOARD is Cartoon character. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 46918
* ramips: fix 7Links PX-4885 dts{, i}, board, image and profile namesJohn Crispin2015-08-171-2/+2
| | | | | | | | The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46629
* ramips: fix Buffalo WMR-300 dts, board, image and profile namesJohn Crispin2015-08-171-2/+2
| | | | | | | | The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46628
* ramips: fix Omnima models, images and profiles namesJohn Crispin2015-08-171-7/+7
| | | | | | | | | | | | | | | | | | | | Official names for supported Omnima products are (as on website): * Omnima HPM * Omnima MiniEMBWiFi * Omnima MiniEMBPlug This patch changes: * board names * dts filenames * profile names * image filenames * LED names for Omnima devices, for consistency. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46627
* ramips: fix Aigale Ai-BR100 dts and profile namesJohn Crispin2015-08-171-2/+2
| | | | | | | | The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46624
* ramips: fix Olimex models, images and profiles namesJohn Crispin2015-08-171-6/+6
| | | | | | | | | | | | | | Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website. The following patch: * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}" * changes filenames of dts and profile files * changes image filenames for Olimex RT5350F-OLinuXino{,-EVB} devices. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46623
* ramips: fix Sitecom WL-341v3 board and image namesJohn Crispin2015-08-171-5/+5
| | | | | | | | | | | | | The following patch changes: * board name from "wl341v3" to "wl-341v3" * dts filename * LED names in dts file for Sitecom WL-341v3 device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46622
* ramips: fix Argus ATP-52B board and image namesJohn Crispin2015-08-171-2/+2
| | | | | | | | | | | | | | The following patch: * changes board name from "argus-atp52b" to "atp-52b" * changes dts filename * fixes LED names in dts file and base-files scripts * removes manufacturer name from image filename for Argus ATP-52B device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46621
* ramips: fix Belkin F7C027 image nameJohn Crispin2015-08-171-1/+1
| | | | | | | | This patch removes manufacturer from Belkin F7C027 image name ("belkinf7c027" -> "f7c027"). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46620
* ramips: fix Asus RT-N56U dts filenameJohn Crispin2015-08-171-2/+2
| | | | | | | | Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46619
* ramips: fix Xiaomi MiWiFi Mini board, image and profile namesJohn Crispin2015-08-171-2/+2
| | | | | | | | | | | | | | The following patch: * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini" * changes filenames of dts and profile * fixes LED names in dts file and base-files scripts * removes manufacturer name from image filename for Xiaomi MiWiFi Mini device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46617
* ramips: fix Asus RP-N53 and Lenovo Y1{, S} image namesJohn Crispin2015-08-171-3/+3
| | | | | | | | | | This patch: * fixes typo (rp_n53 -> rp-n53) in Asus RP-N53 image name * removes manufacturer from image names for Lenovo Y1{,S} devices Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46616
* ramips: fix Asus WL-330N{, 3G} boards namesJohn Crispin2015-08-171-4/+4
| | | | | | | | There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46615
* ramips: fix Zbtlink ZBT-WR8305RT board nameJohn Crispin2015-08-171-2/+2
| | | | | | | | There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46614
* ramips: add subtarget for mt7688John Crispin2015-07-241-0/+14
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 46473
* ramips: add support for STORYLiNK SAP-G3200U3John Crispin2015-07-241-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN. It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons * ethernet switch and USB diag LEDs * UART * GPIOs Tested and not working: * LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?) * failsafe mode (known problem, needs workaround like other MTK based devices) More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46454
* ramips: add support for Planex MZK-DP150NJohn Crispin2015-07-171-0/+3
| | | | | | | | | This patch add support for Planex MZK-DP150N. a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 46405
* ramips: adding support for OY-0001 Wireless RouterJohn Crispin2015-07-141-0/+2
| | | | | | | | | | Adding support for OY-0001 Wireless Router. OY-0001 is a wireless router made by oyewifi.com. Below is the details: MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN. Signed-off-by: Tom Deng <2579131212@qq.com> SVN-Revision: 46349
* ramips: fix typo in WHR1166D mtd size variableJohn Crispin2015-07-071-1/+1
| | | | | | | | Fix typo in WHR1166D mtd size variable Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> SVN-Revision: 46214
* ramips: Add Support for the Linksys RE6500John Crispin2015-06-181-1/+5
| | | | | | | | | | This patch adds support for the Linksys RE6500 Range Extender http://wiki.openwrt.org/toh/linksys/re6500 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 46043
* ramips: Add support for the D-Link DCS-930 B1John Crispin2015-06-181-0/+2
| | | | | | | | http://wiki.openwrt.org/toh/d-link/dcs-930l Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 46042
* ramips: add support for PandoraBox PBR-M1John Crispin2015-06-181-1/+6
| | | | | | | | | This patch is for PandoraBox PBR-M1 which is based on mt7621, all the features work fine, including rtc, leds, button, usb3.0, etc. Signed-off-by: tymon <banglang.huang@foxmail.com> SVN-Revision: 46041
* ramips: Add support for RT5350F-OLinuXino V2John Crispin2015-06-051-0/+8
| | | | | | | | | | | Version 2 : White spaces and alphabetical order problems fixed Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info : https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com> SVN-Revision: 45902
* ramips: fix imagebuilderJohn Crispin2015-05-291-2/+4
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45820
* ramips: check size after paddingFelix Fietkau2015-05-271-1/+1
| | | | | | Signed-off-by: Cristian Morales Vega <cristian@samknows.com> SVN-Revision: 45777
* ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile RouterJohn Crispin2015-05-231-0/+3
| | | | | | | | | | MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB and 1 ethernet port. The original product information can be found at: http://www.aximcom.com/en/MR-102N Signed-off-by: Tai-hwa Liang <atliang@gmail.com> SVN-Revision: 45724
* ramips: add support for Comfast CF-WR800NJohn Crispin2015-05-231-0/+2
| | | | | | | | | This patch adds support for Comfast CF-WR800N, a wall-plug wireless router based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> SVN-Revision: 45722
* ramips: Add support for Microduino MicroWRTJohn Crispin2015-04-091-0/+3
| | | | | | | | | | | | | | | | MicroWRT is an wireless router with 2 USB,1 ethernet port. It has a 16M flash and 64M DDR2 RAM. You can use most interface, such as i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to combine with the core board. The detailed information, please refer to https://www.microduino.cc/wiki/index.php?title=Main_Page This patch adds support for it. Because there is only one port,so disabled VLAN and use eth0 as lan port. and only a power LED control by power pin. Signed-off-by: 盛凯 <shengkai81@gmail.com> SVN-Revision: 45331
* ramips: Add support for ZTE Q7John Crispin2015-04-011-0/+2
| | | | | | | | | | | | | | | ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC. I can,t find any information about this router on ZTE's website. But I found this : http://en.cctairmobi.com/plus/list.php?tid=40 This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D This patch adds support for it. Because there is only one port,I disabled VLAN and use eth0 as lan port. I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-( Signed-off-by: 郭传鈜 <gch981213@gmail.com> SVN-Revision: 45208
* ramips: move relocating loader to common locationJonas Gorski2015-03-306-372/+1
| | | | | | | | Allow other targets to use it, too. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45162
* ralink: FireWRT flash size is up to 16M.John Crispin2015-03-111-1/+1
| | | | | | Signed-off-by: wengbj <fl.service@t-firefly.com> SVN-Revision: 44661
* ramips: Buffalo WZR-AGL300NH target supportJohn Crispin2015-02-161-0/+3
| | | | | | | | | | | | | I got work with this patch. Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons. In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata. signed-off-by: ngc@ff.iij4u.or.jp —— —— SVN-Revision: 44470
* ramips: add support for Xiaomi MiWiFi Mini devicesJohn Crispin2015-02-021-0/+2
| | | | | | | | | This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio wireless router based on the MediaTek MT7620a SoC. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> SVN-Revision: 44238
* ramips: add support for Tenda 3G150BJohn Crispin2015-01-221-0/+3
| | | | | | | | | | | | | | | Add suport for Tenda 3G150B: - cpu: Ralink RT5350F - flash: 4MB - ram: 32MB - 1x USB 2.0 - 1x RJ45 - one reset button - battery powered (BP-4L, 3.7V 1450mAh) Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44073
* ralink: add support for firewrtJohn Crispin2015-01-201-1/+6
| | | | | | | | this is a mt7621 based board Signed-off-by: wengbj <linux.c@foxmail.com> SVN-Revision: 44055
* ramips: add missing copyright info for relocate stubFelix Fietkau2015-01-172-2/+8
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44017