aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt76x8.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-161-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: create image for mt7628 evb boardMathias Kresin2018-04-231-0/+1
| | | | | | | The image for the EVB board got lost with the merge of the mt7628 and mt7688 subtargets. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: image: drop redundant SUPPORTED_DEVICESPiotr Dymacz2018-04-061-1/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for TP-Link TL-WR902AC v3Peter Lundkvist2018-03-181-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router based on MediaTek MT7628N + MT7650E. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet * MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment. Therefore 5Ghz won' work. Flash instruction: The only way to flash LEDE image in TL-WR902AC v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com> [drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for ALFA Network AWUSFREE1Piotr Dymacz2018-02-221-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628. Specification: - MT7628AN (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203) - 2x detachable antennas (RP-SMA) - ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0) - 4x LED (2 driven by GPIO) - 1x button (reset) - 1x mini USB for host and main power input - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Power device with reset button pressed and release it after ~5 sec. 2. Setup static IP 192.168.1.2/4 on your PC. 3. Go to 192.168.1.1 in browser and upload "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Tama W06INAGAKI Hiroshi2018-02-201-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek MT7688AN. Specification: - MT7688AN (575 MHz) - 64 MB of RAM (DDR2 SDRAM) - 16 MB of Flash (SPI) - 1T1R 2.4 GHz - 1x 10/100/1000 Mbps Ethernet - 4x LEDs (GPIO connected: 3), 1x button - 1x USB 2.0 Type-A (host) - UART header on PCB (GND, RX, TX, Vcc from RJ45 side) Flash instruction using sysupgrade image: 1. Connect micro-USB cable for power supply into W06 and turn on the router 2. Connect to wifi with SSID "tama-*" with password. Complete SSID and password are listed on the back of the router 3. Access to 192.168.1.1 and login with user name "admin" and password empty 4. In firmware update（ファームウェア更新） page, click "参照" button and click "ブラウザー" button to open file browser, select the sysupgrade image and press OK button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for TP-Link Archer C50 v3Henryk Heisig2018-02-111-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C50 v3 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7612E. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Flash instruction: The only way to flash LEDE image in ArcherC50v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: various fixes for zbt-we1226Daniel Golle2018-02-061-2/+2
| | | | | | | | | | | Convert userspace code to use generic device-tree compatible board detection method. Users of the existing code will have to use sysupgrade -F once to switch to the new generic board naming. Properly setup pinctrl fixing the switch port LEDs. Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226) Reported-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Widora Neo 32MB flash revisionJackson Ming Hu2018-01-231-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Widora has updated their Widora Neo board recently. The new model uses 32MB WSON-8 factor SPI flash instead of the original 16MB SOP-8 factor SPI flash. All the other hardware components are the same as the first revision. Detailed hardware specs listed below: CPU: MTK MT7688AN RAM: 128MB DDR2 ROM: 32MB WSON-8 factor SPI Flash (Winbond) WiFi: Built-in 802.11n 150Mbps? Ethernet: 10/100Mbps x1 Audio codec: WM8960 Other IO: USB OTG; USB Power+Serial (CP2104); 3x LEDs (Power, LAN, WiFi); 2x Keys (WPS, CPU Reset) 1x Audio In/Out 1x IPEX antenna port 1x Micro SD slot Signed-off-by: Jackson Ming Hu <huming2207@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add flash size postfix to Widora neoMathias Kresin2018-01-231-4/+5
| | | | | | | | | | Rename the Widora neo by adding a flash size prefix. Move the common parts into a dtsi to be prepare everything for upcomming support of the 32MB version. Migrate the Widora neo to the generic board detection as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for ZBT-WE1226Daniel Golle2018-01-231-0/+7
| | | | | | | | MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM Everything except for the switch LEDs works great. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layotSerg Studzinskii2018-01-181-1/+1
| | | | | | | | | | | According to console log during TP-Link TL-WR840N v5 OEM firmware update procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store router's configuration settings, is erased and recreated again during every OEM firmware update procedure, thus does not contain any valuable factory data. So it is conviniant to use this extra 64kB erase block for jffs overlay due limited flash size on this device like it used on TP-Link's ar71xx boards. Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
* ramips: add support for TP-Link Archer C20 v4Maxim Anisimov2018-01-151-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v4 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Flash instruction: The only way to flash LEDE image in ArcherC20v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for TP-Link TL-MR3420 v5Henryk Heisig2017-12-231-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3420 v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-WR841N V13. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 8x LED, 2x button, power input switch Flash instruction: The only way to flash LEDE image in mr3420v5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: move common tplink image build code into own recipeMathias Kresin2017-12-231-8/+20
| | | | | | | | Move common tplink image build code into own recipe. Include the common parts instead of including a full build recipe and overwriting former set varaibles. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-4/+9
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for UniElec U7628-01Piotr Dymacz2017-11-141-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for TP-Link TL-WR840N v5Robert Marko2017-11-081-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 1x LED (GPIO-controlled), 1x button * LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Orange LED is registered so you can later use it for your own purposes. Flash instruction: Unlike TL-WR840N v4 flashing through WEB UI works in v5. 1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image. 2. Go to 192.168.0.1 3. Flash the sysupgrade image through Firmware upgrade section of WEB UI. 4. Wait until green LED stops flashing and use the router. Notes: TFTP recovery is broken since TP-Link reused bootloader code for v4 and that does not take into account only 4 MB of flash and bricks the device. So do not use TFTP Recovery or you will have to rewrite SPI flash. They fixed it in later GPL code,but it is unknown which version of bootloader you have. After manually compiling and flashing bootloader from GPL sources TFTP recovery works properly. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ramips/mt76x8: add initramfs support for tplink 841n v13Alexander Couzens2017-10-091-0/+1
| | | | | | | | | | | | | The tplink 841n v13 requires an tplink v2 image header in front of an initramfs image. To boot an initramfs image: - break the uboot by holding the '4' key - setup your tftp server 192.168.0.255 - tftp 81000000 lede-ramips-mt76x8-tl-wr841n-v13-initramfs-kernel.bin - bootm Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* build: add mktplinkfw2 hardcoded values to makefileThibaut VARÈNE2017-10-061-5/+11
| | | | | | | | | | | This patch adds all the board-specific values currently hardcoded in mktplinkfw2.c back to the respective device declarations in the makefiles. The rationale is to avoid modifying the source code every time a new board or board variant is added. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: merge mt7628/mt7688 into mt76x8L. D. Pinney2017-08-301-0/+166
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi" They are essentially a single subtarget. This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 22:53:07 +0000