aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7620.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: remove factory image for TP-Link Archer C20 v1Stijn Segers2021-02-191-0/+1
| | | | | | | | | | | | | Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one tries to flash an OpenWrt factory image through the TP-Link web UI. The wiki page contains an explicit warning about this [1]. Disable the factory image altogether since it serves no purpose. [1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation Signed-off-by: Stijn Segers <foss@volatilesystems.org> (cherry picked from commit 0265cba40ad4f2b8ff4473ada123c35b53ffd97a)
* ramips: remove factory image for TP-Link Archer C2 v1Stijn Segers2021-02-131-0/+1
| | | | | | | | | | | | | | | | | | | Initial commit 8375623a0640 ("ramips: add support for TP-Link Archer C2") contains detailed installation instructions, which do not mention a factory image. From what I can see, no support to install OpenWrt through the vendor web interface has been added since. The factory image is also conspicuously absent from the device page in the wiki. Yet, it is available for download. I bricked my Archer C2 loading the factory image through the web UI. Serial showed this error during bootloop: Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover This patch disables the undocumented factory image so users won't get tricked into thinking easy web UI flashing actually works. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: drop empty kmod-ledtrig-* packagesSungbo Eo2021-01-151-2/+1
| | | | | | | | | | | | | | The following four led triggers are enabled in generic config. * kmod-ledtrig-default-on * kmod-ledtrig-heartbeat * kmod-ledtrig-netdev * kmod-ledtrig-timer Drop the packages and remove them from DEVICE_PACKAGES. There's no other package depending on them in this repo. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Wavlink WL-WN530HG4Nuno Goncalves2020-10-271-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | Same hardware as Phicomm K2G but different flash layout. Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: To avoid requiring UART for TFTP a dual flash procedure is suggested to install the squashfs image: 1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin to WN530HG4-WAVLINK. 2. Flash this file with the factory web interface. 3. With OpenWRT now running use standard sysupgrade to install the squashfs image. Signed-off-by: Nuno Goncalves <nunojpg@gmail.com> [remove dts-v1, remove model from LED labels, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix partitions and boot for RAVPower RP-WD03Adrian Schmutzler2020-09-111-7/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD03 is a battery powered router, with an Ethernet and USB port. Due due a limitation in the vendor supplied U-Boot bootloader, we cannot exceed a 1.5 MB kernel size, as is the case with recent builds (i.e. post v19.07). This breaks both factory and sysupgrade images. To address this, use the lzma loader (loader-okli) to work around this limitation. The improvements here also address the "misplaced" U-Boot environment partition, which is located between the kernel and rootfs in the stock image / implementation. This is addressed by making use of mtd-concat, maximizing space available in the booted image. This will make sysupgrade from earlier versions impossible. Changes are based on the recently supported HooToo HT-TM05, as the hardware is almost identical (except for RAM size) and is from the same vendor (SunValley). While at it, also change the SPI frequency accordingly. Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions Most of the changes in this commit are the work of Russell Morris (as credited below), I only wrapped them up and added compat-version. Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader to work! Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use proper name for RAVPower RP-WD03Adrian Schmutzler2020-09-111-4/+5
| | | | | | | | The proper model name is RP-WD03 (i.e. with the RP- prefix). Adjust all names to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: disable default build for Ravpower RP-WD03Adrian Schmutzler2020-09-091-0/+1
| | | | | | | | | | This device has a 1.5M kernel size limit during boot and is unbootable since February 2019 [1]. [1] https://forum.openwrt.org/t/ravpower-wd03-does-not-start-with-openwrt-master/49792 Reported-by: Szabolcs Hubai <szab.hu@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for HooToo HT-TM05Russell Morris2020-09-031-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port. Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli). Specifications: SOC: MediaTek MT7620N BATTERY: 10400mAh WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: 64 MB FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz Flash itself specified to 80 MHz, but speed limited by mt7620 SPI fast-read enabled (m25p) LED: Status LED (blue after boot, green with WiFi traffic 4 leds to indicate power level of the battery (unable to control) INPUT: Power, reset button MAC assignment based on vendor firmware: 2.4 GHz *:b4 (factory 0x04) LAN/label *:b4 (factory 0x28) WAN *:b5 (factory 0x2e) Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - Installation from TFTP (recovery) - OpenWRT sysupgrade (Preserving and non-preserving), through the usual ways: command line and LuCI - LEDs (except as noted above) - Button (reset) - I2C, which is needed for reading battery charge status and level - U-Boot environment / variables (from U-Boot, and OpenWrt) Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions I would like to thank @mpratt14 and @xabolcs for their help getting the lzma loader to work! Signed-off-by: Russell Morris <rmorris@rkmorris.us> [drop changes in image/Makefile, fix indent and PKG_RELEASE in uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift, add COMPILE to Device/Default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: make dependency on kmod-usb-net selectiveAdrian Schmutzler2020-08-101-1/+1
| | | | | | | | A bunch of kernel modules depends on kmod-usb-net, but does not select it. Make AddDepends/usb-net selective, so we can drop some redundant +kmod-usb-net definitions for DEVICE_PACKAGES. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear JWNR2010 v5Shibajee Roy2020-08-061-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7620N (580 MHz) - Flash size: 4 MB NOR SPI - RAM size: 32 MB DDR1 - Bootloader: U-Boot - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz) - Switch: MT7620 built-in 10/100 switch with vlan support - Ports: 4x LAN, 1x WAN - Others: 7x LED, Reset button, UART header on PCB (57600 8N1) Flash instructions: 1. Use ethernet cable to connect router with PC/Laptop, any router LAN port will work. 2. To flash openwrt we are using nmrpflash[1]. 3. Flash commands: First we need to identify the correct Ethernet id. nmrpflash -L nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.) 4. Now remove the power cable from router back side and immediately connect it again. You will see flash notification in CMD window, once it says reboot the device just plug off the router and plug in again. Revert to stock: 1. Download the stock firmware from official netgear support[2]. 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware. nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img MAC addresses on stock firmware: LAN = *:28 (label) WAN = *:29 WLAN = *:28 On flash, the only valid MAC address is found in factory 0x4. Special Note: This openwrt firmware will also support other netgear N300 routers like below as they share same stock firmware[3]. JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050 [1] https://github.com/jclehner/nmrpflash [2] https://www.netgear.com/support/product/JWNR2010v5.aspx [3] http://kb.netgear.com/000059663 Signed-off-by: Shibajee Roy <ador250@protonmail.com> [create DTSI, use netgear_sercomm_nor, disable by default, add MAC addresses to commit message, add label MAC address] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate recipes with uimage_padhdrAdrian Schmutzler2020-07-111-2/+2
| | | | | | | | | | | There are already two very similar recipes using uimage_padhdr in ramips target, and a third one is about to be added. Make the recipe more generic, so redefinitions are not necessary anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
* ramips: add support for Netgear EX6120Adrian Schmutzler2020-06-111-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * CPU: 580 MHz * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The device is identical to the EX6130 except for the mains socket and the hardware ID. Installation: The -factory images can be flashed from the device's web interface or via nmrpflash. Notes: MAC addresses were set up based on the EX6130 setup. This is based on prior work of Adam Serbinski and Mathias Buchwald. Tested by Mathias Buchwald. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TRENDnet TEW-810DRJ. Scott Heppler2020-05-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * MediaTek MT7620A (580 Mhz) * 8 MB of FLASH * 64 MB of RAM * 2.4Ghz and 5.0Ghz radios * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * UART header on PCB (57600 8n1) * Green/Orange Power LEDs illuminating a Power-Button Lens * Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens * 3x button - wps, power and reset * U-boot bootloader Installation: The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either the TEW-810DR or DIR-810L and is located at source/user/wolf/cameo/ncc/hostTools. The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0" This may need to be altered if your hardware version is "1.1R". The image can also be directly flashed via serial tftp: 1. Load *.sysupgrade.bin to your tftp server directory and rename for convenience. 2. Set a static ip 192.168.10.100. 3. NIC cable to a lan port. 4. Serial connection parameters 57600,8N1 5. Power on the TEW-810 and press 4 for a u-boot command line prompt. 6. Verify IP's with U-Boot command "printenv". 7. Adjust tftp settings if needed per the tftp documentation 8. Boot the tftp image to test the build. 9. If the image loads, reset your server ip to 192.168.1.10 and restart network. 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image. Notes: The only valid MAC address is found in 0x28 of the factory partition. Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [remove "link rx tx" in 01_leds, format and extend commit message, fix DTS led node names] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for netis WF2770Sungbo Eo2020-05-171-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100/1000Mbps - Switch: MT7530BU - UART: - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 MAC addresses in factory partition: 0x0004: LAN, WiFi 2.4GHz (label_mac-6) 0x0028: not used (label_mac-1) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac+2) Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ASUS RT-AC54UZhijun You2020-05-171-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MTK MT7620A - RAM: 64MB - ROM: 16MB SPI Flash Macronix MX25L12835E - WiFi1: MediaTek MT7620A - WiFi2: MediaTek MT7612E - Button: reset, wps - LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN - Ethernet: 5 ports, 4 LAN + 1 WAN - Other: 1x UART 1x USB2.0 Installation: Update using ASUS Firmware Restoration Tool: 1. Download the ASUS Firmware Restoration Tool but don't open it yet 2. Unplug your computer from the router 3. Put the router into Rescue Mode by: turning the power off, using a pin to press and hold the reset button, then turning the router back on while keeping the reset button pressed for ~5 secs until the power LED starts flashing slowly (which indicates the router has entered Rescue Mode) 4. Important (if you don't do this next step the Asus Firmware Restoration Tool will wrongly assume that the router is not in Rescue Mode and will refuse to flash it): go to the Windows Control Panel and temporarily disable ALL other network adapters except the one you will use to connect your computer to the router 5. For the single adapter you left enabled, temporarily give it the static IP 192.168.1.10 and the subnet mask 255.255.255.0 6. Connect a LAN cable between your computer (make sure to use the Ethernet port of the adapter you've just set up) and port 1 of the router (not the router's WAN port) 7. Rename sysupgrade.bin to factory.trx 8. Open the Asus Firmware Restoration Tool, locate factory.trx and click upload (if Windows shows a compatibility prompt, confirm that the tool worked fine) 9. Flashing and reboot is finished when the power LED stops blinking and stays on MAC assignment based on vendor firmware: 2g 0x4 label 5g 0x8004 label +4 lan 0x22 label +4 wan 0x28 label Signed-off-by: Zhijun You <hujy652@gmail.com> [rebased due to DTSI patch, minor commit message adjustments, fix label MAC address (lan->wan), do spi frequency increase separately] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for LB-Link BL-W1200Pawel Dembicki2020-05-091-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BL-W1200 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612E) - 5x 10/100/1000 Mbps Ethernet (MT7530) - 2x external, non-detachable antennas (Wifi 2.4G/5G) - 1x USB 2.0 - UART (R2) on PCB (57600 8n1) - 9x LED (1 GPIO controlled), 1x button - u-Boot bootloader Known issues: - No status LED. Used WPS LED during boot/failsafe/sysupgrade. Installation: 1. Apply initramfs image via factory web-gui. 2. Install sysupgrade image. How to revert to OEM firmware: - sysupgrade -n -F stock_firmware.bin Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: tidy up image subtarget MakefilesSungbo Eo2020-05-081-18/+11
| | | | | | | | | - use tab indent in image build recipes for consistency - harmonize line wrapping Signed-off-by: Sungbo Eo <mans0n@gorani.run> [use different line wrapping for one recipe] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A1004nsSungbo Eo2020-04-181-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100/1000Mbps - Switch: MT7530BU - USB: 1x 2.0 - UART: - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: disable images for 4M devicesChuanhong Guo2020-04-121-0/+2
| | | | | | | | | default initramfs for 5.4 kernel is larger than 4M, causing build error for oversized initramfs image. disable these images because we have no mechanism for ignoring initramfs errors and the squashfs image will be larger than initramfs anyway. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for D-Link DWR-960Pawel Dembicki2020-04-081-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-960 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610 mpcie card) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Ethernet (1 LAN) (AR8035) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem - UART (J4) header on PCB (57600 8n1) - 9x LED, 2x button - JBOOT bootloader Known issues: - Flash is extremely slow. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* treewide: omit IMAGE_SIZE argument from check-sizeSungbo Eo2020-03-211-19/+19
| | | | | | | | | Now that check-size uses IMAGE_SIZE by default, we can skip the argument from image recipes to reduce redundancy. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: do not add metadata to factory imagesMathias Kresin2020-03-171-2/+2
| | | | | | | The image metadata are openwrt specific and not required for factory images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link RE210 v1Christoph Krapp2020-03-091-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7620A RAM: 64MB FLASH: 8MB SPI WLAN: 2G: MediaTek MT7620A 5G: MediaTek MT7610EN ETH: 1x 10/100/1000M (Atheros AR8035) LED: RSSI (orange/green) WiFi 2G (green) WiFi 5G (green) Power (green) System (red / green) BTN: Power Reset LED WPS Serial ------ P1 - Tx P2 - Rx P3 - GND P4 - VCC Pin 4 is the one closest to the LAN port. MAC overview ------------ WAN *:4c uboot 0x1fc00 2.4 *:4c uboot 0x1fc00 5 *:4e uboot 0x1fc00 +2 Installation ------------ Web interface: It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial/TFTP: You can use initramfs for booting via RAM or flash the image directly. Additional Notes: If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. In order to flash back to stock, the first header and U-Boot needs to be stripped from the original firmware. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [change rssi LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: disable images for Netgear 2700Petr Štetiar2020-03-021-0/+1
| | | | | | Because openwrt-ramips-mt7620-netgear_ex2700-squashfs-factory.bin is too big. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: collect and harmonize TP-Link image variants in common fileAdrian Schmutzler2020-02-011-30/+16
| | | | | | | | | | | | This moves the various variants of common device definitions for TP-Link devices to a common Makefile common-tp-link.mk. This provides the opportunity to reorganize and move parameters between individual device definitions and the common ones. While at it, also use the common definitions for previously independent definitions where appropriate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20iAdrian Schmutzler2020-01-291-1/+0
| | | | | | | | | DEVICE_PACKAGES is specified twice for the same device. Remove the first (=older) assignment. Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move mktplinkfw to tplink-v1-image in image-commands.mkAdrian Schmutzler2020-01-081-19/+2
| | | | | | | | | | | | | | | | | | | | | This move the slightly different target-specific implementations of mktplinkfw from the targets to include/image-commands.mk and renames it to tplink-v1-image. Having a common version will increase consistency between implementation and will complete the tplink build command already present in the new location. Due to the slight differences of the original implementations, this also does some adjustments to the device build commands/variables. This also moves rootfs_align as this is required as dependency. Tested on: - TL-WDR4300 v1 (ath79, factory) - TL-WDR4900 v1 (mpc85xx, sysupgrade) - RE210 v1 (ramips, see Tested-by) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Christoph Krapp <achterin@googlemail.com>
* ramips: fix sysupgrade image for TP-Link RE200v1Andreas Böhler2020-01-051-1/+1
| | | | | | | Images generated for the TP-Link RE200v1 cannot be updated using sysupgrade, because a necessary call to append-metadata was missing. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for TP-Link RE200 v1Andreas Böhler2019-12-311-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN. Specifications -------------- - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled; only 6 supported), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. The 5G LED is currently not supported, since the GPIOs couldn't be determined. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. Additional notes ---------------- MAC address assignment is based on stock-firmware. For me, the device assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G WiFi has a separate MAC with +2. *:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158 *:89 unused userconfig 0x0160 *:8A 5G not present in flash This seems to be the first ramips device with a TP-Link v1 header. The original firmware has the string "EU" embedded, there might be some region- checking going on during the firmware upgrade process. The original firmware also contains U-Boot and thus overwrites the boot loader during upgrade. In order to flash back to stock, the first header and U-Boot need to be stripped from the original firmware. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: rename MTK_SOC to SOCAdrian Schmutzler2019-12-201-93/+93
| | | | | | | This replaces MTK_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-191-48/+63
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A104nsSungbo Eo2019-12-171-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100Mbps - Switch: SoC internal - USB: 1x 2.0 - UART: - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. In contrast to to-be-supported A1004ns, the A104ns has no usable value in 0x1fc40 (uboot), so wan_mac needs to be calculated. Also note that GPIOs for the LEDs really are inverted compared to the A1004ns. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [moved state_default to device DTS, reordered properties in wmac, added comment about wan_mac and LED GPIOs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Netgear EX6130Frederik Noe-Sdun2019-11-081-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. The device seems to use base PCB as EX3700/EX3800, but supporting AC1200 using MT7612E. MAC adresses: 5.0 GHz 0x8004 *:9a 2.4 GHz 0x4 *:9b lan 0x28 *:9b wan 0x2e *:9c Since this is a one-port device, although wan MAC address is set in flash, it is not used in OpenWrt setup. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, extended commit message, tiny DTS style fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips, mt7620: reproducible elecom-header uid/gidPaul Spooren2019-11-061-1/+1
| | | | | | | | | | | | | | | | | | | | | The elecom-header renames the firmware image to v_0.0.0.bin, stores its MD5 sum as v_0.0.0.md5 and tars both files again. Both v_0.0.0 files are created as the build user making it harder to reproduce. This commit sets the owner/group of both files to root by adding extra options to the final tar command. Before: 0 buildbot (101) buildbot (102) 3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin 0 buildbot (101) buildbot (102) 33 2019-11-05 14:43:22.000000 v_0.0.0.md5 After: 0 root (0) root (0) 3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin 0 root (0) root (0) 33 2019-11-05 23:43:08.000000 v_0.0.0.md5 Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: add support for ZBT WE1026-HKristian Evensen2019-11-031-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * When binding the USB LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [rebased onto base-files split, minor style fixes, removed use of USB led as power LED] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-1/+1
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: apply consistent device name/compatible to ZBT-WE1026-5GAdrian Schmutzler2019-09-291-11/+11
| | | | | | | | | | | All Zbtlink ramips devices except the ZBT-WE1026-5G include the zbt-/ZBT- prefix in their model name. This changes ZBT-WE1026-5G to also follow that scheme. The patch moves some block to keep alphatical order. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mkINAGAKI Hiroshi2019-09-251-19/+0
| | | | | | | | | | | I-O DATA WNPR2600G has an "elx-header", so move this definition to generic makefile to use it from mt7621 subtarget. This definition is also added to mt7621.mk in f285e8634c57d28aa970b80c5c59e85485f35c7d, so remove it from mt7621.mk. And added a line to cleanup used header file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-201-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add NAS goodies on U25AWF-H1 + U35[N|W]FChristian Lamparter2019-08-241-2/+4
| | | | | | | | | These devices are sold as a "NAS HDD Enclousure" and have a "NAS Media Streaming & File Server & AP" on the box. That's why I think they should have some support for the HDD right out-of-the-box. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Fon FON2601NOGUCHI Hiroshi2019-07-261-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FON2601 is a wireless router. Specification: - SoC: Mediatek MT7620A (580MHz) - RAM: 128 MiB - ROM: 16 MiB SPI Flash - Wireless: for 11b/g/n (upto 300 Mbps): MT7620A built-in WMAC for 11a/n/ac (upto 867 Mbps): MT7662E - Ethernet LAN: 1 port, upto 100 Mbps - Ethernet WAN: 1 port, upto 1000 Mbps - USB: 1 port (USB 2.0 host) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 1 (Displayed as "WPS" on enclosure) - serial port: 57600n8 pins: Vcc(3.3V), Rx, Tx, GND (left to right, viewed from outside of board) Installation (only available via UART): 1. download sysupgrade binary image by wget command 2. write sysupgrade binary image to Flash command is: mtd write sysupgrade.bin firmware 3. reboot Important Notice: Only one button is displayed as "WPS" on enclosure. However, it is configured as "reset" (factory resetting feature). Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: use kiB instead of B for IMAGE_SIZEAdrian Schmutzler2019-07-251-1/+1
| | | | | | | This cosmetical patch is just meant to make comparing/checking IMAGE_SIZE values easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove ralink_default_fw_size_xxx variablesAdrian Schmutzler2019-07-251-43/+43
| | | | | | | | | | | There are frequent examples of the ralink_default_fw_size_xxx variables being used to "roughly" set flash size without caring about the actual size of the firmware partition. To discourage this behavior, this patch removes the variables and just sets IMAGE_SIZE by its numeric value for each target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default IMAGE_SIZE for ramips targetAdrian Schmutzler2019-07-251-0/+22
| | | | | | | | | | | | | | | | | | | Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE for all devices in ramips target, i.e. this will be set if a device does not specify IMAGE_SIZE itself. From 92 devices using that default due to a "missing" IMAGE_SIZE, 14 were incorrect by a small amount (i.e. still "8M" flash) and 12 were completely off ("16M", "4M", ...). This patch thus removes the _default_ IMAGE_SIZE and defines IMAGE_SIZE for each device individually. This should indicate to people supporting new devices that this parameter has to be cared about. For the present code, this patch is cosmetical. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: fix IMAGE_SIZE for all devicesAdrian Schmutzler2019-07-251-13/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes IMAGE_SIZE for all devices based on the partition size given in DTS: DEVICE *.MK *.DTS VERDICT aigale_ai-br100 7936k 0x7c0000 alfa-network_ac1200rm 16064k 0xfb0000 alfa-network_tube-e4g 16064k 0xfb0000 asus_rp-n53 - 0x7b0000 default asus_rt-ac51u (16M) 0xfb0000 asus_rt-n12p - 0xfb0000 wrong asus_rt-n14u - 0xfb0000 wrong bdcom_wap2100-sk 15808k 0xf70000 buffalo_whr-1166d 15040k 0xfb0000 wrong buffalo_whr-300hp2 6848k 0x7b0000 wrong buffalo_whr-600d 6848k 0x7b0000 wrong buffalo_wmr-300 - 0x7b0000 default comfast_cf-wr800n - 0x7b0000 default dlink_dch-m225 6848k 0x6b0000 dlink_dir-510l - 0xde0000 wrong dlink_dir-810l 6720k 0x690000 dlink_dwr-116-a1 - 0x7e0000 wrong dlink_dwr-118-a1 - 0xfe0000 wrong dlink_dwr-118-a2 - 0xfe0000 wrong dlink_dwr-921-c1 (16M) 0xfe0000 wrong dlink_dwr-921-c3 [(16M)] 0xfe0000 wrong dlink_dwr-922-e2 (16M) 0xfe0000 wrong dovado_tiny-ac - 0x7b0000 default edimax_br-6478ac-v2 7616k 0x00790000 wrong edimax_ew-7476rpc 7744k 0x00790000 edimax_ew-7478ac 7744k 0x00790000 edimax_ew-7478apc 7744k 0x00790000 elecom_wrh-300cr (16M) 0xdf0000 wrong glinet_gl-mt300a (16M) 0xf80000 wrong glinet_gl-mt300n (16M) 0xf80000 wrong glinet_gl-mt750 (16M) 0xf80000 wrong head-weblink_hdrm200 16064k 0xfb0000 hiwifi_hc5661 15872k 0xf80000 hiwifi_hc5761 15872k 0xf80000 hiwifi_hc5861 15872k 0xf80000 hnet_c108 16777216 0xfb0000 wrong iodata_wn-ac1167gr 6864k 0x6b4000 iodata_wn-ac733gr3 6992k 0x6d4000 kimax_u25awf-h1 16064k 0xfb0000 kimax_u35wf 16064k 0xfb0000 kingston_mlw221 15744k 0xf60000 kingston_mlwg2 15744k 0xf60000 lava_lr-25g001 - 0xfe0000 wrong lenovo_newifi-y1 (16M) 0xfb0000 lenovo_newifi-y1s (16M) 0xfb0000 linksys_e1700 - 0x7b0000 default microduino_microwrt 16128k 0xfc0000 netgear_ex2700 (4M) 0x3b0000 netgear_ex3700 7744k 0x790000 netgear_wn3000rp-v3 - 0x7b0000 default nexx_wt3020-4m (4M) 0x3b0000 nexx_wt3020-8m - 0x7b0000 default ohyeah_oy-0001 (16M) 0xfb0000 phicomm_k2g 7552k 0x760000 phicomm_psg1208 - 0x7b0000 default phicomm_psg1218a - 0x7b0000 default phicomm_psg1218b - 0x7b0000 default planex_cs-qr10 - 0x7b0000 default planex_db-wrt01 - 0x7b0000 default planex_mzk-750dhp - 0x7b0000 default planex_mzk-ex300np - 0x730000 wrong planex_mzk-ex750np - 0x730000 wrong ralink_mt7620a-evb - 0x7b0000 default ralink_mt7620a-mt7530-evb - 0x7b0000 default ralink_mt7620a-mt7610e-evb - 0x7b0000 default ralink_mt7620a-v22sg-evb - 0x7f80000 wrong ravpower_wd03 (8M) 0x7b0000 sanlinking_d240 (16M) 0xfb0000 sercomm_na930 20m 0x1400000 tplink_archer-c20i - 0x7a0000 wrong tplink_archer-c20-v1 - 0x7a0000 wrong tplink_archer-c2-v1 - 0x7a0000 wrong tplink_archer-c50-v1 - 0x7a0000 wrong tplink_archer-mr200 - 0x7b0000 default vonets_var11n-300 (4M) 0x3b0000 wrtnode_wrtnode (16M) 0xfb0000 xiaomi_miwifi-mini (16M) 0xf80000 wrong youku_yk1 (32M) 0x1fb0000 yukai_bocco - 0x7b0000 default zbtlink_we1026-5g-16m 16777216 0xfb0000 wrong zbtlink_zbt-ape522ii - 0xf80000 wrong zbtlink_zbt-cpe102 - 0x760000 wrong zbtlink_zbt-wa05 - 0x760000 wrong zbtlink_zbt-we2026 - 0x760000 wrong zbtlink_zbt-we826-16m (16M) 0xfb0000 zbtlink_zbt-we826-32m (32M) 0x1fb0000 zbtlink_zbt-we826-e 32448k 0x1fb0000 zbtlink_zbt-wr8305rt - 0x7b0000 default zte_q7 - 0x7b0000 default zyxel_keenetic-omni - 0x7b0000 default zyxel_keenetic-omni-ii - 0x7b0000 default zyxel_keenetic-viva 16064k 0xfb0000 No verdict means that the device is correctly set. Legend: ( ): Value is set via ralink_default_fw_size_xxM [ ]: Value is derived from parent definition - : Value is not set and derived from default definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix ralink_default_fw_size_16MAdrian Schmutzler2019-07-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | In ramips, there are the following predefined values for IMAGE_SIZE ralink_default_fw_size_4M 3866624 3776k 0x3B0000 ralink_default_fw_size_8M 8060928 7872k 0x7B0000 ralink_default_fw_size_16M 16121856 15744k 0xF60000 ralink_default_fw_size_32M 33226752 32448k 0x1FB0000 Out of those, the "16M" value is obviously odd, as it provides more room for the remaining partitions than the tree others. Of the devices in all subtargets, there are actually > 50 that have a firmware partition with 0xFB0000 size, while only 5 (!) have 0xF60000. From the former, many are set to ralink_default_fw_size_16M anyway, although it is wrong at the present point. Consequently, it makes sense to change ralink_default_fw_size_16M to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with 0xF60000. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Sort all subtarget MakefilesAdrian Schmutzler2019-07-101-445/+445
| | | | | | | | | This patch applies sorting to the definitions as whole blocks. Sorting has been performed fully automatic, line count differences originate from double empty lines removed. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: Name DTS files based on schemeAdrian Schmutzler2019-07-101-91/+88
| | | | | | | | As introduced with ath79, DTS files for ramips will now be labelled soc_vendor_device.dts(i). With this change, DTS files can be selected automatically without further manual links. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-29 02:37:34 +0000