aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7620.mk
Commit message (Collapse)AuthorAgeFilesLines
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-1/+1
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: apply consistent device name/compatible to ZBT-WE1026-5GAdrian Schmutzler2019-09-291-11/+11
| | | | | | | | | | | All Zbtlink ramips devices except the ZBT-WE1026-5G include the zbt-/ZBT- prefix in their model name. This changes ZBT-WE1026-5G to also follow that scheme. The patch moves some block to keep alphatical order. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mkINAGAKI Hiroshi2019-09-251-19/+0
| | | | | | | | | | | I-O DATA WNPR2600G has an "elx-header", so move this definition to generic makefile to use it from mt7621 subtarget. This definition is also added to mt7621.mk in f285e8634c57d28aa970b80c5c59e85485f35c7d, so remove it from mt7621.mk. And added a line to cleanup used header file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-201-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add NAS goodies on U25AWF-H1 + U35[N|W]FChristian Lamparter2019-08-241-2/+4
| | | | | | | | | These devices are sold as a "NAS HDD Enclousure" and have a "NAS Media Streaming & File Server & AP" on the box. That's why I think they should have some support for the HDD right out-of-the-box. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Fon FON2601NOGUCHI Hiroshi2019-07-261-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FON2601 is a wireless router. Specification: - SoC: Mediatek MT7620A (580MHz) - RAM: 128 MiB - ROM: 16 MiB SPI Flash - Wireless: for 11b/g/n (upto 300 Mbps): MT7620A built-in WMAC for 11a/n/ac (upto 867 Mbps): MT7662E - Ethernet LAN: 1 port, upto 100 Mbps - Ethernet WAN: 1 port, upto 1000 Mbps - USB: 1 port (USB 2.0 host) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 1 (Displayed as "WPS" on enclosure) - serial port: 57600n8 pins: Vcc(3.3V), Rx, Tx, GND (left to right, viewed from outside of board) Installation (only available via UART): 1. download sysupgrade binary image by wget command 2. write sysupgrade binary image to Flash command is: mtd write sysupgrade.bin firmware 3. reboot Important Notice: Only one button is displayed as "WPS" on enclosure. However, it is configured as "reset" (factory resetting feature). Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: use kiB instead of B for IMAGE_SIZEAdrian Schmutzler2019-07-251-1/+1
| | | | | | | This cosmetical patch is just meant to make comparing/checking IMAGE_SIZE values easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove ralink_default_fw_size_xxx variablesAdrian Schmutzler2019-07-251-43/+43
| | | | | | | | | | | There are frequent examples of the ralink_default_fw_size_xxx variables being used to "roughly" set flash size without caring about the actual size of the firmware partition. To discourage this behavior, this patch removes the variables and just sets IMAGE_SIZE by its numeric value for each target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default IMAGE_SIZE for ramips targetAdrian Schmutzler2019-07-251-0/+22
| | | | | | | | | | | | | | | | | | | Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE for all devices in ramips target, i.e. this will be set if a device does not specify IMAGE_SIZE itself. From 92 devices using that default due to a "missing" IMAGE_SIZE, 14 were incorrect by a small amount (i.e. still "8M" flash) and 12 were completely off ("16M", "4M", ...). This patch thus removes the _default_ IMAGE_SIZE and defines IMAGE_SIZE for each device individually. This should indicate to people supporting new devices that this parameter has to be cared about. For the present code, this patch is cosmetical. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: fix IMAGE_SIZE for all devicesAdrian Schmutzler2019-07-251-13/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes IMAGE_SIZE for all devices based on the partition size given in DTS: DEVICE *.MK *.DTS VERDICT aigale_ai-br100 7936k 0x7c0000 alfa-network_ac1200rm 16064k 0xfb0000 alfa-network_tube-e4g 16064k 0xfb0000 asus_rp-n53 - 0x7b0000 default asus_rt-ac51u (16M) 0xfb0000 asus_rt-n12p - 0xfb0000 wrong asus_rt-n14u - 0xfb0000 wrong bdcom_wap2100-sk 15808k 0xf70000 buffalo_whr-1166d 15040k 0xfb0000 wrong buffalo_whr-300hp2 6848k 0x7b0000 wrong buffalo_whr-600d 6848k 0x7b0000 wrong buffalo_wmr-300 - 0x7b0000 default comfast_cf-wr800n - 0x7b0000 default dlink_dch-m225 6848k 0x6b0000 dlink_dir-510l - 0xde0000 wrong dlink_dir-810l 6720k 0x690000 dlink_dwr-116-a1 - 0x7e0000 wrong dlink_dwr-118-a1 - 0xfe0000 wrong dlink_dwr-118-a2 - 0xfe0000 wrong dlink_dwr-921-c1 (16M) 0xfe0000 wrong dlink_dwr-921-c3 [(16M)] 0xfe0000 wrong dlink_dwr-922-e2 (16M) 0xfe0000 wrong dovado_tiny-ac - 0x7b0000 default edimax_br-6478ac-v2 7616k 0x00790000 wrong edimax_ew-7476rpc 7744k 0x00790000 edimax_ew-7478ac 7744k 0x00790000 edimax_ew-7478apc 7744k 0x00790000 elecom_wrh-300cr (16M) 0xdf0000 wrong glinet_gl-mt300a (16M) 0xf80000 wrong glinet_gl-mt300n (16M) 0xf80000 wrong glinet_gl-mt750 (16M) 0xf80000 wrong head-weblink_hdrm200 16064k 0xfb0000 hiwifi_hc5661 15872k 0xf80000 hiwifi_hc5761 15872k 0xf80000 hiwifi_hc5861 15872k 0xf80000 hnet_c108 16777216 0xfb0000 wrong iodata_wn-ac1167gr 6864k 0x6b4000 iodata_wn-ac733gr3 6992k 0x6d4000 kimax_u25awf-h1 16064k 0xfb0000 kimax_u35wf 16064k 0xfb0000 kingston_mlw221 15744k 0xf60000 kingston_mlwg2 15744k 0xf60000 lava_lr-25g001 - 0xfe0000 wrong lenovo_newifi-y1 (16M) 0xfb0000 lenovo_newifi-y1s (16M) 0xfb0000 linksys_e1700 - 0x7b0000 default microduino_microwrt 16128k 0xfc0000 netgear_ex2700 (4M) 0x3b0000 netgear_ex3700 7744k 0x790000 netgear_wn3000rp-v3 - 0x7b0000 default nexx_wt3020-4m (4M) 0x3b0000 nexx_wt3020-8m - 0x7b0000 default ohyeah_oy-0001 (16M) 0xfb0000 phicomm_k2g 7552k 0x760000 phicomm_psg1208 - 0x7b0000 default phicomm_psg1218a - 0x7b0000 default phicomm_psg1218b - 0x7b0000 default planex_cs-qr10 - 0x7b0000 default planex_db-wrt01 - 0x7b0000 default planex_mzk-750dhp - 0x7b0000 default planex_mzk-ex300np - 0x730000 wrong planex_mzk-ex750np - 0x730000 wrong ralink_mt7620a-evb - 0x7b0000 default ralink_mt7620a-mt7530-evb - 0x7b0000 default ralink_mt7620a-mt7610e-evb - 0x7b0000 default ralink_mt7620a-v22sg-evb - 0x7f80000 wrong ravpower_wd03 (8M) 0x7b0000 sanlinking_d240 (16M) 0xfb0000 sercomm_na930 20m 0x1400000 tplink_archer-c20i - 0x7a0000 wrong tplink_archer-c20-v1 - 0x7a0000 wrong tplink_archer-c2-v1 - 0x7a0000 wrong tplink_archer-c50-v1 - 0x7a0000 wrong tplink_archer-mr200 - 0x7b0000 default vonets_var11n-300 (4M) 0x3b0000 wrtnode_wrtnode (16M) 0xfb0000 xiaomi_miwifi-mini (16M) 0xf80000 wrong youku_yk1 (32M) 0x1fb0000 yukai_bocco - 0x7b0000 default zbtlink_we1026-5g-16m 16777216 0xfb0000 wrong zbtlink_zbt-ape522ii - 0xf80000 wrong zbtlink_zbt-cpe102 - 0x760000 wrong zbtlink_zbt-wa05 - 0x760000 wrong zbtlink_zbt-we2026 - 0x760000 wrong zbtlink_zbt-we826-16m (16M) 0xfb0000 zbtlink_zbt-we826-32m (32M) 0x1fb0000 zbtlink_zbt-we826-e 32448k 0x1fb0000 zbtlink_zbt-wr8305rt - 0x7b0000 default zte_q7 - 0x7b0000 default zyxel_keenetic-omni - 0x7b0000 default zyxel_keenetic-omni-ii - 0x7b0000 default zyxel_keenetic-viva 16064k 0xfb0000 No verdict means that the device is correctly set. Legend: ( ): Value is set via ralink_default_fw_size_xxM [ ]: Value is derived from parent definition - : Value is not set and derived from default definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix ralink_default_fw_size_16MAdrian Schmutzler2019-07-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | In ramips, there are the following predefined values for IMAGE_SIZE ralink_default_fw_size_4M 3866624 3776k 0x3B0000 ralink_default_fw_size_8M 8060928 7872k 0x7B0000 ralink_default_fw_size_16M 16121856 15744k 0xF60000 ralink_default_fw_size_32M 33226752 32448k 0x1FB0000 Out of those, the "16M" value is obviously odd, as it provides more room for the remaining partitions than the tree others. Of the devices in all subtargets, there are actually > 50 that have a firmware partition with 0xFB0000 size, while only 5 (!) have 0xF60000. From the former, many are set to ralink_default_fw_size_16M anyway, although it is wrong at the present point. Consequently, it makes sense to change ralink_default_fw_size_16M to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with 0xF60000. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Sort all subtarget MakefilesAdrian Schmutzler2019-07-101-445/+445
| | | | | | | | | This patch applies sorting to the definitions as whole blocks. Sorting has been performed fully automatic, line count differences originate from double empty lines removed. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: Name DTS files based on schemeAdrian Schmutzler2019-07-101-91/+88
| | | | | | | | As introduced with ath79, DTS files for ramips will now be labelled soc_vendor_device.dts(i). With this change, DTS files can be selected automatically without further manual links. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-101-150/+200
| | | | | | | | | | | | | | | This will "rename" devices in Makefiles to the pattern used in DTS compatible. This will systematize naming of devices enormously. As device names are used to for default SUPPORTED_DEVICES entries, we need to adjust the source for /tmp/sysinfo/board_name, too. So remove relevant entries from base-files/lib/ramips.sh and use device compatible for that. Despite that, base-files are updated, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Improve compatible for TP-Link Archer devicesAdrian Schmutzler2019-07-101-4/+6
| | | | | | | | Include "Archer" in compatible as it is part of the device name. Update Makefile device names where necessary to match compatible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add missing DEVICE_VENDORDaniel Golle2019-07-101-1/+1
| | | | | Fixes commit ee66fe4ea9a6f5e3f47a063f850bac57e1fb411a Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: convert DEVICE_TITLE to new variablesDaniel Golle2019-07-061-92/+199
| | | | | | Also unify naming and add details where they were missing. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Edimax EW-7478APCBirger Koblitz2019-06-201-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN) USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header) BTN: Reset/WPS LED: - Power (white) - Internet (blue) - Wifi (blue) - USB (blue) UART: UART is present as Pads with throughholes on the PCB. They are located in the lower right corner (GbE ports facing up) 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimax.setup) Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflicts in 01_leds and mt7620.mk, dts whitespace issues] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax EW-7476RPC / EW-7478ACBirger Koblitz2019-06-201-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: 192.168.9.2/24). http://192.168.9.2/index.asp ramips: add Edimax EW-7478AC SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimaxext.setup) Or push wpa button on power on and send firmware via tftp to 192.168.1.6 The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal antennas it has 2 external ones. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflict in 01_leds] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-241-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkdlinkfw: add kernel image offsetPawel Dembicki2019-03-241-33/+21
| | | | | | | | Some boards with JBOOT have partiton between bootloader and kernel image. This patch add possibility to change kernel partition start address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-211-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-111-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-141-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVBDeng Qingfang2019-02-051-0/+1
| | | | | | This enables MT7610E of the EVB Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: consolidate seama image build codeMathias Kresin2018-12-301-11/+2
| | | | | | | | Create a common template which has the required image build code defined. Add some new variables to pass individual parts to the seama recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for DLINK DWR-922-E2Simon Quigley2018-12-291-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not sure if supported, I didn't try), wireless router with QMI LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-922-e2:green:signalstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Works correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui, or via recovery interface: How to recover/revert to OEM firmware: 1.) Push and hold the reset button and turn on the power. Wait until all LEDs start rapidly blinking (~10sec.) 2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set one manually 3.) Upload original factory image via JBOOT http interface at IP 192.168.123.254 4.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. 5.) You can optionally telnet to 192.168.123.254 before or during the upload and it will report the flashing status, memory address etc. 6.) Once web UI and/or telnet says "Success", power cycle the router, or type "reboot" into the telnet session. Signed-off-by: Simon Quigley <squigley@squigley.net> [squashed commits, word wrap commit message, rename signal strenght led name to match what is used for the DWR-921-C1 since they share the led configuration, add label referenced in the aliases node] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb packagesMathias Kresin2018-12-151-4/+16
| | | | | | | | | Add the usb drivers for all boards with enabled ochi/ehci node in the dts file. Fixes: FS#1987 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: remove unnecessary usb packagesMathias Kresin2018-12-151-3/+3
| | | | | | These are either installed as dependency or not required at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb ohci driverMathias Kresin2018-12-151-6/+6
| | | | | | | Add the USB 1.1 driver for all boards not having a fixed USB 2.0 device attached to the USB bus. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: several fixes for HC5x61Deng Qingfang2018-12-151-5/+5
| | | | | | | | | | | | | | | | | | | | | - Mark other partitions as read-only for HC5x61 - Only enable USB and PCIe for HC5761/HC5861 HC5661 doesn't have a USB port, and there is nothing attached to its PCIe. - Fix HC5761 switch ports HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports. - Fix HC5861 5GHz radio HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN. - Fix HC5761/HC5861 WiFi LEDs After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1. - Fix HC5x61 image size It should be 15872k (0xf80000) Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix Netgear EX3700/EX3800 wireless driver selectionMathias Kresin2018-12-041-1/+1
| | | | | | Fix the typo to select kmod-mt76x2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A1Pawel Dembicki2018-12-031-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: select only the matching mt76 driverChen Minqiang2018-12-031-24/+27
| | | | | | | | | | | | | Because every device has selected the corresponding mt76 driver, we can now disable the mt76 metapackage by default to make sure that other devices (those don't need mt76) avoid selecting unwanted packages. We can find the hardware specifies and determine the dependencies on these sites: https://wikidevi.com/wiki/ https://openwrt.org/toh/hwdata/ Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: drop mt76 driver for boards without mt76 wirelessChen Minqiang2018-12-031-4/+4
| | | | | | | These boards don't have a mt76 wireless at all and don't need any of the mt76 family drivers. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: bdcom-wap2100: Enable mt7610e 5GHz radioPetr Štetiar2018-11-281-1/+1
| | | | | | | | | | | | The 5GHz radio of this device uses an mt7610e PCI-E chip, which has been recently started to be supported. mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 mt76x0e 0000:01:00.0: ASIC revision: 76100002 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: add DIR-810L's mt7610e 5 GHz radioRoger Pueyo Centelles2018-11-281-1/+2
| | | | | | | | | | The 5 GHz radio of this device uses an mt7610e pci-e chip, which has been recently added support. Tested on the actual device as AP and client, TCP throughput ~90 Mbps U/D. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: improve BDCOM WAP2100-SK supportMathias Kresin2018-11-261-5/+4
| | | | | | | | | | | | | | | | | | | | | Use the generic board detection instead of the target specific one as all recent additions are doing. Setup the USB led via devicetree (a58535771f11) and include the required driver by default. Merge the led userspace setting with an existing identical case. Use the wps led for boot status indication. Move the partitions into a partition table node (6031ab345df8) and drop needless labels. Drop misplaced cells properties (53624c1702e6). Cleanup the pinmux and only switch pins to gpio functions which a referenced as gpio in the dts. Match the maximum image size with the size of the firmware partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Lava LR-25G001Pawel Dembicki2018-11-261-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Lava LR-25G001 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN) - 2x external, detachable antennas - 1x USB 2.0 - UART (J3) header on PCB (57600 8n1) - 8x LED (3x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - Work only three Gigabit ports (3/5, 1 WAN and 2LAN) Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SKPetr Štetiar2018-11-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory OpenWrt image it's referenced as BDCOM WAP2100-SK device. Specifications: - SoC: MediaTek MT7620A - RAM: 128 MB - Flash: 16 MB - Ethernet: 5 FE ports - Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported) - UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config - LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G - Other: USB port, SD card slot and 2x external antennas (non-detachable) Flashing instructions: A) The U-Boot has HTTP based firmware upgrade A1) Flashing notes We've identified so far two different batches of units, unfortunately each batch has different U-Boot bootloader flashed with different default environment variables, thus each batch has different IP address for accessing web based firmware updater. * First batch has web based bootloader IP address 1.1.1.1 * Second batch has web based bootloader IP address 192.168.1.250 In case you can't connect to either of those IPs, you can try to get the default IP address via two methods: A1.1) Serial console, then the IP address is visible during the boot ... HTTP server is starting at IP: 1.1.1.1 raspi_read: from:40004 len:6 HTTP server is ready! ... A1.2) Over telnet/SSH using this command: root@bdcom:/# grep ipaddr= /dev/mtd0 ipaddr=1.1.1.1 A2) Flashing with browser * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask * Reboot the device and try to reach web based bootloader in the browser with the following URL http://1.1.1.1 * Quickly select the firmware sysupgrade file and click on the `Update firmware` button, this all has to be done within 10 seconds, bootloader doesn't wait any longer If done correctly, the web page should show UPDATE IN PROGRESS page with progress indicator. Once the flashing completes (it takes roughly around 1 minute), the device will reboot to the OpenWrt firmware A3) Flashing with curl sudo ip addr add 1.1.1.2/24 dev eth0 curl \ --verbose \ --retry 3 \ --retry-delay 1 \ --retry-max-time 30 \ --connect-timeout 30 \ --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \ http://1.1.1.1 Now power on the router. B) The U-boot is based on Ralink SDK so we can flash the firmware using UART. 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX) 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3Daniel Golle2018-11-251-0/+1
| | | | | | | | | Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio which wasn't supported at the time the devices were added to OpenWrt. Now that we got it, include kmod-mt76x0e in images for those devices. Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix Archer C20 sysupgradeSteffen Förster2018-09-261-1/+0
| | | | | | | | | | The sysupgrade image failed the check due to the wrong string in the supported devices. This patch provides the correct name by dropping the SUPPORTED_DEVICES to use the default generated name. Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net> [drop the SUPPORTED_DEVICES, the old name was never used in a release] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: ex2700: actually remove kmod-mt76*Joseph C. Lehner2018-09-261-1/+1
| | | | | | | | | | | | | | When building using the multiple devices option with per-device root filesystem, only the meta package mt76 is omitted but not the dependencies selected by the package. Explicitly exclude all 3 mt76 packages, plus the metapackage. Otherwise, these modules will be included in the build, wasting a few hundred kilobytes. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [mention the root cause of the issue in the commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-151-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-131-3/+3
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Edimax BR-6478AC v2Daniel Gimpelevich2018-08-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie. Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated. Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Macronix MX25L6405D - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7612E 5GHz 802.11ac - Switch: Mediatek MT7530W Gigabit Switch - USB: Yes 1 x 2.0 Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 4. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: add support for Blueendless Kimax U35WFAdemar Arvati Filho2018-07-071-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908 Based on: https://github.com/lede-project/source/pull/965 Specification: - SoC: MediaTek MT7620N - CPU/Speed: 580 MHz - Flash-Chip: KH25L12835F Spi Flash - Flash size: 16 MiB - RAM: 64 MiB - LAN: 1x 100 Mbps Ethernet - WiFi SoC-integrated: 802.11bgn - 1x USB 2.0 - UART: for serial console Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 3. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 21:23:22 +0000