aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7620.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-241-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit dfecf94c2059998411f95067de3866aa7cdf5ec9)
* mt7620: disable image generation for Nexx WT3020 (4MB)Hauke Mehrtens2019-09-081-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file openwrt-19.07-snapshot-r10495-db5164d3d0-ramips-mt7620-wt3020-4M-squashfs-factory.bin is too big Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mt7620: disable image generation for Netgear EX2700Petr Štetiar2019-07-201-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-241-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkdlinkfw: add kernel image offsetPawel Dembicki2019-03-241-33/+21
| | | | | | | | Some boards with JBOOT have partiton between bootloader and kernel image. This patch add possibility to change kernel partition start address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-211-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-111-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-141-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVBDeng Qingfang2019-02-051-0/+1
| | | | | | This enables MT7610E of the EVB Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: consolidate seama image build codeMathias Kresin2018-12-301-11/+2
| | | | | | | | Create a common template which has the required image build code defined. Add some new variables to pass individual parts to the seama recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for DLINK DWR-922-E2Simon Quigley2018-12-291-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not sure if supported, I didn't try), wireless router with QMI LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-922-e2:green:signalstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Works correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui, or via recovery interface: How to recover/revert to OEM firmware: 1.) Push and hold the reset button and turn on the power. Wait until all LEDs start rapidly blinking (~10sec.) 2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set one manually 3.) Upload original factory image via JBOOT http interface at IP 192.168.123.254 4.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. 5.) You can optionally telnet to 192.168.123.254 before or during the upload and it will report the flashing status, memory address etc. 6.) Once web UI and/or telnet says "Success", power cycle the router, or type "reboot" into the telnet session. Signed-off-by: Simon Quigley <squigley@squigley.net> [squashed commits, word wrap commit message, rename signal strenght led name to match what is used for the DWR-921-C1 since they share the led configuration, add label referenced in the aliases node] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb packagesMathias Kresin2018-12-151-4/+16
| | | | | | | | | Add the usb drivers for all boards with enabled ochi/ehci node in the dts file. Fixes: FS#1987 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: remove unnecessary usb packagesMathias Kresin2018-12-151-3/+3
| | | | | | These are either installed as dependency or not required at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add usb ohci driverMathias Kresin2018-12-151-6/+6
| | | | | | | Add the USB 1.1 driver for all boards not having a fixed USB 2.0 device attached to the USB bus. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: several fixes for HC5x61Deng Qingfang2018-12-151-5/+5
| | | | | | | | | | | | | | | | | | | | | - Mark other partitions as read-only for HC5x61 - Only enable USB and PCIe for HC5761/HC5861 HC5661 doesn't have a USB port, and there is nothing attached to its PCIe. - Fix HC5761 switch ports HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports. - Fix HC5861 5GHz radio HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN. - Fix HC5761/HC5861 WiFi LEDs After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1. - Fix HC5x61 image size It should be 15872k (0xf80000) Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix Netgear EX3700/EX3800 wireless driver selectionMathias Kresin2018-12-041-1/+1
| | | | | | Fix the typo to select kmod-mt76x2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A1Pawel Dembicki2018-12-031-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: select only the matching mt76 driverChen Minqiang2018-12-031-24/+27
| | | | | | | | | | | | | Because every device has selected the corresponding mt76 driver, we can now disable the mt76 metapackage by default to make sure that other devices (those don't need mt76) avoid selecting unwanted packages. We can find the hardware specifies and determine the dependencies on these sites: https://wikidevi.com/wiki/ https://openwrt.org/toh/hwdata/ Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: drop mt76 driver for boards without mt76 wirelessChen Minqiang2018-12-031-4/+4
| | | | | | | These boards don't have a mt76 wireless at all and don't need any of the mt76 family drivers. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: bdcom-wap2100: Enable mt7610e 5GHz radioPetr Štetiar2018-11-281-1/+1
| | | | | | | | | | | | The 5GHz radio of this device uses an mt7610e PCI-E chip, which has been recently started to be supported. mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 mt76x0e 0000:01:00.0: ASIC revision: 76100002 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: add DIR-810L's mt7610e 5 GHz radioRoger Pueyo Centelles2018-11-281-1/+2
| | | | | | | | | | The 5 GHz radio of this device uses an mt7610e pci-e chip, which has been recently added support. Tested on the actual device as AP and client, TCP throughput ~90 Mbps U/D. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: improve BDCOM WAP2100-SK supportMathias Kresin2018-11-261-5/+4
| | | | | | | | | | | | | | | | | | | | | Use the generic board detection instead of the target specific one as all recent additions are doing. Setup the USB led via devicetree (a58535771f11) and include the required driver by default. Merge the led userspace setting with an existing identical case. Use the wps led for boot status indication. Move the partitions into a partition table node (6031ab345df8) and drop needless labels. Drop misplaced cells properties (53624c1702e6). Cleanup the pinmux and only switch pins to gpio functions which a referenced as gpio in the dts. Match the maximum image size with the size of the firmware partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Lava LR-25G001Pawel Dembicki2018-11-261-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Lava LR-25G001 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN) - 2x external, detachable antennas - 1x USB 2.0 - UART (J3) header on PCB (57600 8n1) - 8x LED (3x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - Work only three Gigabit ports (3/5, 1 WAN and 2LAN) Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SKPetr Štetiar2018-11-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory OpenWrt image it's referenced as BDCOM WAP2100-SK device. Specifications: - SoC: MediaTek MT7620A - RAM: 128 MB - Flash: 16 MB - Ethernet: 5 FE ports - Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported) - UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config - LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G - Other: USB port, SD card slot and 2x external antennas (non-detachable) Flashing instructions: A) The U-Boot has HTTP based firmware upgrade A1) Flashing notes We've identified so far two different batches of units, unfortunately each batch has different U-Boot bootloader flashed with different default environment variables, thus each batch has different IP address for accessing web based firmware updater. * First batch has web based bootloader IP address 1.1.1.1 * Second batch has web based bootloader IP address 192.168.1.250 In case you can't connect to either of those IPs, you can try to get the default IP address via two methods: A1.1) Serial console, then the IP address is visible during the boot ... HTTP server is starting at IP: 1.1.1.1 raspi_read: from:40004 len:6 HTTP server is ready! ... A1.2) Over telnet/SSH using this command: root@bdcom:/# grep ipaddr= /dev/mtd0 ipaddr=1.1.1.1 A2) Flashing with browser * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask * Reboot the device and try to reach web based bootloader in the browser with the following URL http://1.1.1.1 * Quickly select the firmware sysupgrade file and click on the `Update firmware` button, this all has to be done within 10 seconds, bootloader doesn't wait any longer If done correctly, the web page should show UPDATE IN PROGRESS page with progress indicator. Once the flashing completes (it takes roughly around 1 minute), the device will reboot to the OpenWrt firmware A3) Flashing with curl sudo ip addr add 1.1.1.2/24 dev eth0 curl \ --verbose \ --retry 3 \ --retry-delay 1 \ --retry-max-time 30 \ --connect-timeout 30 \ --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \ http://1.1.1.1 Now power on the router. B) The U-boot is based on Ralink SDK so we can flash the firmware using UART. 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX) 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3Daniel Golle2018-11-251-0/+1
| | | | | | | | | Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio which wasn't supported at the time the devices were added to OpenWrt. Now that we got it, include kmod-mt76x0e in images for those devices. Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix Archer C20 sysupgradeSteffen Förster2018-09-261-1/+0
| | | | | | | | | | The sysupgrade image failed the check due to the wrong string in the supported devices. This patch provides the correct name by dropping the SUPPORTED_DEVICES to use the default generated name. Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net> [drop the SUPPORTED_DEVICES, the old name was never used in a release] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: ex2700: actually remove kmod-mt76*Joseph C. Lehner2018-09-261-1/+1
| | | | | | | | | | | | | | When building using the multiple devices option with per-device root filesystem, only the meta package mt76 is omitted but not the dependencies selected by the package. Explicitly exclude all 3 mt76 packages, plus the metapackage. Otherwise, these modules will be included in the build, wasting a few hundred kilobytes. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [mention the root cause of the issue in the commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-151-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-131-3/+3
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Edimax BR-6478AC v2Daniel Gimpelevich2018-08-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie. Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated. Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Macronix MX25L6405D - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7612E 5GHz 802.11ac - Switch: Mediatek MT7530W Gigabit Switch - USB: Yes 1 x 2.0 Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 4. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: add support for Blueendless Kimax U35WFAdemar Arvati Filho2018-07-071-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908 Based on: https://github.com/lede-project/source/pull/965 Specification: - SoC: MediaTek MT7620N - CPU/Speed: 580 MHz - Flash-Chip: KH25L12835F Spi Flash - Flash size: 16 MiB - RAM: 64 MiB - LAN: 1x 100 Mbps Ethernet - WiFi SoC-integrated: 802.11bgn - 1x USB 2.0 - UART: for serial console Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 3. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* ramips: move zyimage define to common MakefileMaxim Anisimov2018-07-041-4/+0
| | | | Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for TP-Link Archer C2Franz Flasch2018-06-251-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Winbond 25Q64BVSIG - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac - Switch: RTL8367RB Gigabit Switch - USB: Yes 1 x 2.0 Preparing a TFTP recovery image for initial flashing: Currently the only method to install openwrt for the first time is via TFTP download in u-boot. After first install you can use regular updates. WARNING: This method also overwrites the bootloader partition! Create a TFTP recovery image: 1) Download a stock TP-Link Firmware file here: https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware 2) Extract u-boot from the binary file: #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072 3) Now merge the sysupgrade image and the u-boot into one binary: #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin The resulting image can be flashed via TFTP recovery mode. Flash instructions: 1) To flash the recovery image, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC2V1_tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS/Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds. It will try to download the recovery image and flash it. It can take up to 20-25 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: Add support for Phicomm K2GChuanhong Guo2018-06-211-0/+8
| | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for YUKAI Engineering Inc. BOCCOYuheiOKAWA2018-05-181-0/+7
| | | | | | | | | | | | | BOCCO is a communication robot provided by YUKAI Engineering Inc. SoC: MT7620A MEM: 256MB Flash: 8MB NAND: 512MB (non support) Include Sound DAC and AMP. No Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
* ramips: add support for Ravpower WD03Matthias Badaire2018-05-071-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RavPower WD03 is a battery powered SD card reader and a USB port. Specifications: SOC: MediaTek MT7620N BATTERY: 6000mah WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: PM Tech PMD708416CTR-5CN 32 MB FLASH: Holtek HT66F40 - 8 MB Flash LED: Power button and 4 leds to indicate power level of the battery (could not get control of that) INPUT: Power, reset button OTHER: USB SD-Card reader with card detect on GPIO#42 Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Installation: - Download the sysupgrade image - Place it in the root of a clean TFTP server running on your computer. - Rename the image to "kernel" — be sure there is no file extension. - Plug the WD03 into your computer via ethernet. - Set your computer to use 10.10.10.254 as its IP address. - With your WD03 shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254 and install the kernel file. Once it has finished installation of the kernel file, it will search for a (nonexistent) rootfs file — when it begins searching for this file, shut down the WD03 by holding the power button normally. - Start up your WD03 normally. Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-2/+2
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add U-Boot env support for ALFA Network AC1200RMPiotr Dymacz2018-04-061-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: image: drop redundant SUPPORTED_DEVICESPiotr Dymacz2018-04-061-1/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for DLINK DWR-921-C3Pawel Dembicki2018-04-041-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-921-C3 Wireless Routers with LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for DLINK DWR-921-C1Giuseppe Lippolis2018-04-041-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-921-c1:green:sigstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: add support for D-Link DWR-116-A1/2Pawel Dembicki2018-03-181-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC. Specification: MediaTek MT7620N (580 Mhz) 32 MB of RAM 8 MB of FLASH 802.11bgn radio 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) 2x external, non-detachable antennas UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1) 6x LED (GPIO-controlled), 2x button JBOOT bootloader Known issues: WAN LED is drived by uartl tx pin. I decide to use this pin as uartlite tx pin. Installation: Apply factory image via http web-gui. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1Maxim Anisimov2018-01-151-14/+14
| | | | | | | | This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1" because of TPLINK released new TP-Link Archer C20 v4. Additionally migration to the generic board detection has been made. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for ALFA Network AC1200RMPiotr Dymacz2018-01-151-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN. Specification: - MT7620A (580 MHz) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4 - 2T2R 2.4 GHz (MT7620A) - 2T2R 5 GHz (MT7612EN) - 1x USB 2.0 - 9x LED (8 driven by GPIO) - 1x button (reset) - DC jack for main power input (12-24 V) - 2x UART, I2C, I2S and LED headers Flash instruction (do it under U-Boot, using UART and TFTP server): Select option "2: Load system code then write to Flash via TFTP" and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Vonets VAR11N-300Andrew Crawley2017-12-211-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet cable, one extra Ethernet port, and an internal antenna, based on the MediaTek MT7620n chipset. Specs: - MT7620n WiSoC @ 600MHz - 32 MB SDRAM - 4 MB SPI flash - 2T2R 2.4GHz WiFi-N - 1 attached 10/100 Ethernet cable (LAN) - 1 10/100 Ethernet port (WAN) - 1 attached USB / barrel 5vdc power cable - 5 LEDs (see notes below) - 1 reset button - 1 UART (3 pads on board) Installation: The stock firmware does not support uploading new firmware directly, only checking the manufacturer's site for updates. This process may be possible to spoof, but the update check uses some kind of homebrew encryption that I didn't investigate. Instead, you can install via a backdoor: 1. Set up a TFTP server to serve the firmware binary (lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin) 2. Factory reset the device by holding the reset button for a few seconds. 3. Open the web interface (default IP: 192.168.253.254) 4. Log in with the "super admin" credentials: username `vonets`, password `vonets26642519`. 5. On the "Operative Status" page, click the text "System Uptime", then quickly click the uptime value. 6. If successful, an alert dialog will appear reading "Ated start", and the device will now accept telnet connections. If the alert does not appear, repeat step 5 until it works (the timing is a bit tricky). 7. Telnet to the device using credentials "admin / admin" 8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin -r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g <tftp-server-ip>` 9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4` 10. Reboot Tested: - LAN / WAN ethernet - WiFi - LAN / WAN / status LED GPIOs (see notes below) - Reset button - Sysupgrade Notes: LEDs: The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue LED for WiFi, and a pair of "status" LEDs connected to the same GPIO (the blue LED lights when the GPIO is low, and the green when it's high). I was unable to determine how to operate the WiFi LED, as it does not appear to be controlled by a GPIO directly. Recovery: The default U-boot installation will only boot from flash due to a missing environment block. I generated a valid 4KB env block using U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an external programmer. After this, it was possible to enter the U-boot commandline interface and download a new image via TFTP (`tftpboot 81b00000 <image-filename>`), but while I could boot this image sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted the flash chip. The sysupgrade file can be written to flash at 0x50000 using an external programmer. Signed-off-by: Andrew Crawley <acrawley@gmail.com>
* ramips: sync image filename with boardnameMathias Kresin2017-12-211-0/+6
| | | | | | | | | | | | | Use <manufacturer>_<modelname> as image name for board using the devicetree compat string as boardname. Replace the underline of the device define, to keep the SUPPORTED_DEVICES in sync with a devicetree compat string based boardname. Override the default SUPPORTED_DEVICES for board which are having an userspace boardname with an underline. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Asus RT-N11P / RT-N12+ / RT-N12E b1Zoltan HERPAI2017-12-061-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | This is a variant of the MT7620N-based Asus routers. Specifications: - MT7620N (580 MHz) - 32 MB RAM - 8 MB Flash - 5x 10/100Mbps Ethernet (built-in switch) - 2.4 GHz WLAN - 2x external, non-detachable antennas - UART (J2) header on PCB (115200 8n1) Flash instructions: 1. Configure PC with static IP 192.168.1.75/24 2. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds. All 4 LEDs will start to blink, which is when the router will accept firmware files via TFTP. No known limitations on firmware filenames, just send it with a TFTP client to 192.168.1.1. 3. Router will download file from server, write it to flash and reboot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 12:14:12 +0000