aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7620.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix Planex CS-QR10 device packagesMathias Kresin2017-11-221-1/+3
| | | | | | | | | Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will not be autoselected. Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix DCH-M225 supportMathias Kresin2017-11-221-1/+1
| | | | | | | | | | | | | | Setting the pins of the UARTF group to GPIO+I2S at the time the I2C driver loads is to late for the wps GPIO button. The gpio-keys driver fails to load since the pin used by the wps button is not yet set to GPIO. The wps button with the rfkill keycode is essential for this wireless only board. Add the missing sound and I2C kernel modules corresponding to the device nodes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mt7620: image.mk: make elecom-header reproducibleAlexander Couzens2017-11-061-1/+3
| | | | | | | | | elecom-header adds a timestamp dependency. Replace the timestamps with SOURCE_DATE_EPOCH [0] variable. [0] https://reproducible-builds.org/specs/source-date-epoch/ Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: fix Youku-YK1 supportEdmunt Pienkowsky2017-10-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix default usb support for nexx wt3020-8MAlberto Bursi2017-10-251-0/+1
| | | | | | | the nexx wt3020-8M has a usb 2.0 port, add usb 2.0 support packages to its default package list. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* ramips: add support for Kimax U25AWF-H1Daniel Kucera2017-10-141-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection and battery, based on MediaTek MT7620A. Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643 Specification: - MT7620A CPU - 64 MB of RAM - 16 MB of FLASH - 802.11bgn WiFi - 1x 10/100 Mbps Ethernet - USB 2.0 Host - UART for serial console Flash instruction: 1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin 2. Open webinterface a upgrade 3. After boot connect via ethernet to ip 192.168.1.1 Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com> [fix reset button gpio, don't add a lan/wan vlan config for single port board, add -H1 suffix do make sure that this revision of the board is supported/tested] Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: add mktplinkfw2 hardcoded values to makefileThibaut VARÈNE2017-10-061-10/+21
| | | | | | | | | | | This patch adds all the board-specific values currently hardcoded in mktplinkfw2.c back to the respective device declarations in the makefiles. The rationale is to avoid modifying the source code every time a new board or board variant is added. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: add support for TP-Link Archer C20 v1Maxim Anisimov2017-09-131-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v1 is a router with 5-port FE switch and non-detachable antennas. It's very similiar to TP-Link Archer C50. Also it's based on MediaTek MT7620A+MT7610EN. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 8x LED (GPIO-controlled*), 2x button, power input switch - 1 x USB 2.0 port * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the blue part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. So, to flash this device we must to prepare image using original firmware from tp-link site with uboot. Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot. There are two ways to flash the device to LEDE: 1) Using tftp mode with UART connection and original LEDE image - Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp server directory - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, power up the router and press key "4" to access U-Boot CLI. - Use the following commands to update the device to LEDE: setenv serverip 192.168.0.66 tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset - After that the device will reboot and boot to LEDE 2) Using tftp mode without UART connection but require some manipulations with target image - Download and unpack TP-Link Archer C20 v1 firmware from original web site - Split uboot.bin from original firmware by this command (example): dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1 - Create ArcherC20V1_tp_recovery.bin using this command: cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin - Place ArcherC20V1_tp_recovery.bin in tftp server directory. - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. - Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: Add support for ZBT WE1026-5GKristian Evensen2017-09-111-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZBT WE1026-5G (http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the ZBT WE826 image could be used. However, as the name implies, the -5G comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz radio, the addition of 5GHz means that a separate image is needed for the WE1026-5G. I suspect that this image will also work on the previous WE1026, but I don't have a device to test with. The WE1026-5G has following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x 5GHz wifi (MT7612) * 1x button. * 3x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working: * The 5GHz WIFI LED is completely dead. I suspect the issue is the same as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is controlled by the driver, and mt76 (currently) does not support this. Not tested: * SD card reader. Notes: * The modem (labeled 3G/4G) and power LEDs are controlled by the hardware. * There is a 32MB version of this device available, but I do not have access to it. I have therefor only added support for the 16MB version, but added all the required infrastructure to make adding support for the 32MB version easy. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the reset button pressed for ~5sec when booting to start the web server. Set the address of the network interface on your machine to 192.168.1.2/24, and point your browser to 192.168.1.1 to access the recovery UI. From the recovery UI you can upload a firmware image. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Archer C50v1: support US and EU versionsThibaut VARENE2017-09-091-4/+6
| | | | | | | | | | | | | | | | | For the Archer C50v1, the EU and US versions are differentiated by their respective HW additional version (0x0 for US, 0x2 for EU). The stock web interface checks this field before flashing, making it impossible to flash the current (US) factory image on EU hardware. However the bootloader does not check this field, making it possible to use a single sysupgrade image for both hardware. This patch adds the necessary build bits to generate both EU and US factory images, and renames the target as "Archer C50v1" since there are as of now 3 different versions of Archer C50 (all with different CPUs). Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add support for the HNET C108Kristian Evensen2017-09-091-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. Only power is connected, this port is meant for charging other devices. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working (also applies to the factory firmware): * Wifi LED. It is always switched on, there is no relation to the up/down state or activity of the wireless interface. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Netgear EX3800Thibaut VARENE2017-08-031-3/+4
| | | | | | | | | | | | The Netgear EX3800 is essentially an EX3700 with a mains output socket. Both devices use the exact same firmware image (original firmware is named EX3700-EX3800-version.chk). This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and updating the necessary glue. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: EX3700: rename factory.bin to factory.chkThibaut VARENE2017-08-031-2/+2
| | | | | | | The stock firmware upgrade interface requires the file to end with a .chk extension. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: image: simplify TP-Link Archer devices definitionsPiotr Dymacz2017-06-291-11/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: move mktplinkfw2 related commands to image-commands.mkPiotr Dymacz2017-06-291-12/+12
| | | | | | | | | There are already two targets (lantiq, ramips) which use mktplinkfw2 tool for creating images. This de-duplicates code, introduces two new build commands: tplink-v2-header, tplink-v2-image and makes use of them in place of old, (sub)target specific ones. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* Move enablemodem from ramips to new package adb-enablemodem and make it used ↵Filip Moc2017-05-271-1/+1
| | | | | | also by TL-MR6400 Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for Asus RT-AC51UØrjan Malde2017-05-101-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A (580 MHz) - RAM: 64 MiB (Winbond W9751G6JB-25) - Flash: 16 MiB (Spansion S25FL128SAIF00) - LAN: x4 100M - WAN: x1 100M - Others: USB 2.0, reset button, wps button and 9 LEDs Issues: - 5 GHz band is not functional (missing driver support) Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75; Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the sysupgrade image, and press upload TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin tftp> quit Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
* ramips: strip padding from TP-Link sysupgrade imagesHenryk Heisig2017-05-051-3/+3
| | | | | | This reduce size of sysupgrade firmware. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add factory firmware for Tp-Link C20i/C50Henryk Heisig2017-05-051-0/+4
| | | | | | TP-Link firmware doesn't accept sysupgrade.bin with metadata. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add ZBT-WE826 32MB variantMathias Kresin2017-04-251-4/+13
| | | | | | | | The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the device tree source file, rename the currently supported 16 MByte version and add the 32 MByte variant. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add former board names to PSG1218 variantsDaniel Golle2017-04-211-0/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add former used board names to metadataMathias Kresin2017-04-211-0/+2
| | | | | | | | | We need to keep the former used (unmodified) boardname in the metadata. Otherwise an upgrade from an board using the old boardname will be refused. Fixes: a75ce960ac1b ("ramips: use different board names for variants") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rename PSG1218 to match labelDaniel Golle2017-04-211-8/+8
| | | | | | | | Fix previous commit to be less ambigous: PSG1218 rev.A = 5 ports, external PA, heatsinks PSG1218 rev.B = 4 ports, internal PA, no heatsinks Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: split Phicomm PSG1218 and PSG1218K2CDaniel Golle2017-04-211-1/+8
| | | | | | | | | PSG1218 got only 4 Ethernet ports and WAN on port 3 while PSG1218K2C got 5 Ethernet ports and WAN on port 4 Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Zbtlink ZBT-WE2026Vaclav Svoboda2017-03-171-0/+6
| | | | | | | | | | | | | | | | | | This patch adds support for the Zbtlink ZBT-WE2026. Specification: - SoC: MediaTek MT7620N (580MHz) - RAM: 64 MiB - Flash: 8 MiB SPI - LAN: 4x100M - WAN: 1x100M Installation through bootloader webserver: - With the power unplugged press and hold reset button. - Plug power and hold reset button until LED starts to blink. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ramips: sort mt7620 image file alphabeticalMathias Kresin2017-03-121-246/+246
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear EX3700Joseph C. Lehner2017-03-121-0/+12
| | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. Co-authored-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: Improve Sanlinking D240 configKristian Evensen2017-03-111-1/+1
| | | | | | | | | | | | | | | | | * The left most mini-PCIe slot (the one attached to SIM2) can be power-cycled by setting GPIO 0 to high/low. * The D240 only needs the MT76x2 module, so update makefile to reflect this. Note that until the default mt7620 target is updated, then kmod-mt76 (and thus kmod-mt7603) will be selected by default. v2->v3: * Indentation error. v1->v2: * Rename gpio and remove redundant comment (thanks Piotr Dymacz) Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmcFurong Xu2017-03-111-3/+3
| | | | | | | mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block. And, we remove kmod-sdhci dependence assignment from all related target devices. Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: remove kmod-mt76* from EX2700 imagesJoseph C. Lehner2017-03-011-1/+1
| | | | | | | These modules are not needed by the EX2700, since it does not have an external wifi chip (MT7620A is covered by rt2x00). Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: include only kmod-mt76-core in EX2700 imageJoseph C. Lehner2017-02-261-0/+1
| | | | | | | This patch frees up flash space on the EX2700, by removing unused mt76 drivers and firmware. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: add support for Sanlinking D240Kristian Evensen2017-02-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* build: centralize fakeroot codeJoseph C. Lehner2017-02-041-2/+2
| | | | | | | | | | | | | This patch moves the fakeroot code required by some devices to `image-commands.mk`. Create the fakeroot on the fly by using the undocumented -s (skip copy) parameter of mkimage. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy rootfs for mkimage] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: cleanup mt7620 Netgear image codeJoseph C. Lehner2017-01-271-16/+8
| | | | | | | 1. Reuse functions defined in `image-commands.mk` 2. Rename fakeroot image Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: ZyXEL Keenetic Viva: align factory imagesVitaly Chekryzhev2017-01-261-1/+1
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Omni align factory imagesVitaly Chekryzhev2017-01-201-2/+2
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add support for Netgear WN3000RPv3Thibaut VARENE2017-01-181-0/+11
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* build: use mkhash to replace various quirky md5sum/openssl callsFelix Fietkau2017-01-051-4/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: use new image build code for more devicesMathias Kresin2016-12-241-7/+0
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use different board names for variantsMathias Kresin2016-12-241-2/+0
| | | | | | | | | | | | Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix image validation errorsMathias Kresin2016-12-241-0/+2
| | | | | | | | | | | The name from the Device define will be used in the metadata. Due to typos/different spelling, this name might not match the one exported in /lib/ramips.sh. Fix all name mismatches which were found by checking if the name used in the metadata exists in /lib/ramips.sh. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix tplink image building fix sysupgrade firmware on MR200Henryk Heisig2016-12-241-4/+5
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-221-0/+10
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-221-0/+20
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add size checks/append metadata where missingMathias Kresin2016-11-271-6/+12
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: append metadata to imagesFelix Fietkau2016-11-191-8/+10
| | | | | | | metadata checks are not enforced yet, because some images are still being built by legacy code Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-181-0/+14
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-3/+3
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-041-0/+7
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-271-0/+7
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-10 07:21:48 +0000