aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/files
Commit message (Collapse)AuthorAgeFilesLines
* ramips: remove further mt7621 code from local ethernet driverAdrian Schmutzler2020-08-265-265/+2
| | | | | | | | | | | | | | | While commit 734a8c46e703 focussed on removing stuff directly selected by the NET_RALINK_* symbols, this patch removes additional unused mt7621-specific code from the ethernet driver. As with the previous patch, the main reason is to reduce the amount of code we have to maintain and care about. Note that this patch still keeps a few lines with IS_ENABLED(CONFIG_SOC_MT7621) in mtk_eth_soc.h/.c, as this file is still selected for the mt7621 subtarget. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove legacy ethernet driver components for mt7621Adrian Schmutzler2020-08-218-1433/+6
| | | | | | | | | | | | | | | | The mt7621 subtarget has been switched to DSA quite a while ago and seems to run sufficiently fine. Build with older kernels than 5.4 has been disabled directly during the kernel bump, so our local ethernet driver is unused in master since then. Therefore, let's remove the mt7621-specific parts of "our" ethernet driver, so we don't have to maintain them and it's obvious to everybody that they are not used anymore. This also drops the offloading components as this was specifically implemented to depend on mt7621. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add arl_table support for MT7530Salvatore Mesoraca2020-07-171-0/+119
| | | | | | | Use switch.h API to expose MT7530's ARL table to user space. Signed-off-by: Salvatore Mesoraca <salvatore@samknows.com>
* ramips: fix sd pollingQin Wei2020-06-271-0/+4
| | | | | | | | | | This is fixed in 18.06, it appears again in 19.07. Currently mt7628 sdcard driver do not support polling mode which is for the device do not have card-detect pin to detect sd card insert. Without this patch, device will not detect sdcard is inserted. This patch is a fix of that. Signed-off-by: Qin Wei <support@vocore.io>
* ramips: 5.4: handle ERR_PTR properlySungbo Eo2020-05-191-1/+1
| | | | | | | of_get_mac_address can return ERR_PTR since 5.2, so the return pointer should be checked before used. Otherwise it might cause an oops during boot. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: ralink-eth: fix leftover dma dev argumentChuanhong Guo2020-04-131-1/+1
| | | | | Fixes: 05dee5833a ("ramips: ralink-eth: fix device struct passed to dma functions") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: ralink-eth: add support for 5.4 kernelChuanhong Guo2020-04-122-0/+34
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: ralink-eth: fix device struct passed to dma functionsChuanhong Guo2020-04-121-14/+12
| | | | | | | dma functions needs the struct from platform_device instead of the one for ethernet interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: move and rename out-of-tree mtk eth driverChuanhong Guo2020-04-1226-0/+8616
| | | | | | | move the driver into shared 'files' directory and rename all symbols from mediatek/mtk to ralink. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mtk-mmc: set correct DMA maskDENG Qingfang2020-04-041-1/+1
| | | | | | | | | | | Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for simple noncoherent platforms") changed MIPS dma handling, the mmc driver fails because it doesn't have a dma mask is set. So set the correct dma mask. Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: move MTK MMC driver to files directoryDENG Qingfang2020-04-047-0/+4021
| | | | | | | Move MTK MMC driver from "files-4.14" to "files" so kernel 5.4 can use it Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ralink: drop old ethernet driverJohn Crispin2015-12-1721-6842/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47899
* ralink: remove stray "+" from ethernet driverJohn Crispin2015-12-121-1/+1
| | | | | | | | this is what you get if you manually apply patches with c&p Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47877
* ralink: bump to the target to v4.3John Crispin2015-12-102-8/+11
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47831
* ramips: fix for kernel 4.0 napi repoll need return budgets numberFelix Fietkau2015-10-301-1/+4
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47306
* ramips: Enable rx of 1536 bytes ethernet frames on MT7621John Crispin2015-10-051-4/+4
| | | | | | | | | | | The default switch frame size (with FCS + header) is 1536 bytes. But the GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to receive ethernet frames using the full of MTU 1500 + an extra VLAN header + VLAN header added by the switch. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47117
* ramips: Fix too small rx bufferJohn Crispin2015-10-051-4/+12
| | | | | | | | | | | | | | | | | | The driver assumes that the maximum received buffer for non-jumbo frames is 1536 bytes. But the allocation of the rx fragment doesn't reflect that. It currently allocates fragments which will only be large enough to be used as rx buffer with the size of 1534 bytes. This is problematic because the GMAC will now try to write to 2 bytes which don't belong to its receive buffer when a large enough ethernet frame is received. This may already be a problem on existing chips but will at least become a problem when the 1536 byte rx modus is enabled on MT7621a. It is required on this SoC to receive ethernet frames which use their full 1500 bytes MTU and a VLAN header next to the switch VLAN tag. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47116
* ramips: Fix setting of rx buffer lengthJohn Crispin2015-10-052-2/+3
| | | | | | | | | | | | | | The length of the DMA rx buffer was always set to 0 because the function for extracting the length was used to calculate the value for setting it. Instead the macro has to be split in a get and set function similar to the TX_DMA_(GET_|)PLEN(0|1) macro. No problem was noticed on MT7621a before this was changed and thus maybe it was hidden by different problem which is not yet fixed. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47115
* ramips: Allow to receive vlan over untag ports on MT7530John Crispin2015-10-051-3/+33
| | | | | | | | | | | | | | | | | | | | The MT7530 switch driver with enable_vlan set will automatically set all ports to the user port mode. The hardware will remove the incoming vlan tag on these ports and use it for its internal vlan. This is usually not wanted and makes it impossible to communicate via vlan over the switch in both directions. It is possible to configure a switch port to "transparent mode" when this port is only used as untag in the switch VLANs. This will disable the VLAN untagging of packets when they were received on this port. The tagging on "tag" ports based on the vlan id is still working. The transparent port mode cannot be used when a port is both used in a VLAN as "tag" and in another one as "untag" port. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47114
* ramips: collect rx related members to fe_rx_ring structFelix Fietkau2015-07-103-58/+69
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 46295
* ramips: add xmit_more supportFelix Fietkau2015-07-102-20/+33
| | | | | | | | | | | | | | | use pktgen to verify on rt3662. can improve transmit rate. pkt_size 1500 burst 1 : 807Mb/sec burst 8 : 984Mb/sec pkt_size 60 burst 1 : 57Mb/sec burst 8 : 236Mb/sec Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 46294
* ralink: add support for mt7621 switch countersJohn Crispin2015-06-181-1/+187
| | | | | | Signed-off-by: Cristian Morales Vega <cristian@samknows.com> SVN-Revision: 46050
* ramips: improve tx clean up and add fe_tx_ring structFelix Fietkau2015-06-053-70/+83
| | | | | | | | | | if there is any new tx need to clean up. do it in next napi poll. collect tx related members to fe_tx_ring struct. for better cache usage and more readable. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 45895
* ramips: change ethernet napi interrupt sequenceFelix Fietkau2015-06-051-5/+4
| | | | | | | | | | when open device. first ready napi software rx. then enable hardware interrupt. final start software tx queue to send data. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 45894
* ramips: fix ethernet vlan tx offload support check when deleteFelix Fietkau2015-06-051-1/+1
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 45893
* ramips: make ethernet register map u16 instead of u32Felix Fietkau2015-03-224-6/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44940
* ramips: increase NAPI weight for mt7621 to improve routing performance a bit ↵Felix Fietkau2015-03-211-3/+3
| | | | | | | | more Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44918
* ralink: support change tx/rx ring sizeJohn Crispin2015-03-133-31/+52
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44741
* ralink: use random generate mac address instead of default one.John Crispin2015-03-136-10/+6
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44740
* ralink: fix when tx done is 0 also need to clean interrupt statusJohn Crispin2015-02-111-3/+3
| | | | | | | Signed-off-by: michael lee <igvtee@gmail.com> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44401
* ralink: fix hw status almost full not work on mt7620 and mt7621John Crispin2015-02-096-6/+31
| | | | | | | | | | | | | | the old FE_INT_STATUS register becomes two registers. FE_INT_STATUS and INT_STATUS. so the hw status almost full must change to read from FE_INT_STATUS register. tx/rx done read from INT_STATUS register. mt7620 datasheet define CNT_GDM1_AF at BIT(29). but after test it should be BIT(13). why? Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44371
* ralink: add 3.18 supportJohn Crispin2015-02-093-5/+11
| | | | | | | | keep default as 3.14, mt7621 gic need to be ported to 3.18 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44349
* ramips: fix ethernet driver tx completion pollingFelix Fietkau2015-02-011-2/+2
| | | | | | | | | | | - budget is decremented with completed frames, so don't check if done is smaller - ACK the interrupt before processing further frames to fix a small race condition. Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44234
* ralink: check ethernet MAC address whether it is validJohn Crispin2015-01-281-1/+3
| | | | | | | | | The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff. This patch is purpose to fix this issue. Signed-off-by: wengbj <linux.c@foxmail.com> SVN-Revision: 44166
* ralink: fix ethernet feature TSO not workFelix Fietkau2015-01-247-155/+197
| | | | | | | | | | | | | | | | * fix TSO features verify on mt7621 firewrt board * improve tx clean up. no need to access uncached memory. also use TX_DTX register instead of read tx ring DONE bit * mt7621 need napi weight 64 to get more performance * remove netif_receive_skb, after kernel version 3.7 tcp4_gro_receive can handle tcp checksum. on rt2880 use iperf tcp LAN to WAN throughput test. with gro 135 Mbits/sec. without gro 80.4Mbits/sec. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44118
* ralink: init tx/rx vlan offload register for mt7621Felix Fietkau2015-01-242-5/+23
| | | | | | | | | | on mt7621 don't have tx vlan vid registers. so set FE_REG_FE_DMA_VID_BASE to 0. set rx vlan offload register to disable. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44117
* ralink: use fe_max_buf_size to get rx buffer sizeFelix Fietkau2015-01-241-7/+5
| | | | | | | | | | the rx_buf_size now is 1534 when mtu is 1500. the ethernet frame with vlan tag and FCS is 1522. so the buffer is enough. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44116
* ramips: fix ethernet vlan tx offload support checkFelix Fietkau2015-01-241-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44115
* ralink: fix ethernet rx buffer size breakageFelix Fietkau2015-01-181-2/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44047
* ralink: improve check rx sg function. use check frags instead of function callFelix Fietkau2015-01-183-14/+8
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44046
* ralink: correct handle hardware rx 2bytes offsetFelix Fietkau2015-01-183-13/+25
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44045
* ralink: use fe_reset to control all resetFelix Fietkau2015-01-188-41/+28
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44044
* ralink: improve tx_timeout functionFelix Fietkau2015-01-184-15/+87
| | | | | | | | | | * use default timeout value * print more debug ring info * move timeout reset function to workqueue Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44043
* ralink: reduce access to uncached tx/rx dma ring bufferFelix Fietkau2015-01-184-53/+81
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44041
* ramips: fix tx bql related race condition in the ethernet driverFelix Fietkau2015-01-171-4/+5
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43995
* ramips: use a larger number of rx descriptors on mt7621 to work around rx ↵Felix Fietkau2015-01-131-0/+4
| | | | | | | | overrun related packet loss Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43953
* ramips: remove interrupt coalescing, it is unnecessary with napi polling and ↵Felix Fietkau2015-01-137-78/+40
| | | | | | | | could reduce throughput Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43952
* ramips: disable ethernet checksum offloads for mt7621, they are brokenFelix Fietkau2015-01-021-1/+10
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43811
* ramips: use netif_receive_skb instead of napi_gro_receive when rx csum ↵Felix Fietkau2015-01-021-1/+4
| | | | | | | | offload is unavailable Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43810
* ralink: fix tx vlan offload and hardware statusJohn Crispin2014-11-192-27/+40
| | | | | | | | | | | | | hardware status and tx vlan offload support on all targets except rt5350. so i modify the IS_ENABLE condition only for mt7621. support mt7621 hardware status reference by SDK. but i don't have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE to 0 to let software count. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 43303