aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/files
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Allow ethernet interface to be taken down and up againGabor Juhos2010-10-051-0/+4
| | | | | | | | | | Taking the ramips ethernet interface down and up again resulted in the driver not receiving any frames anymore. Fix this by correctly disabling interrupts in the hw on ifdown. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> SVN-Revision: 23243
* ramips: Ralink RT305x, support for Prolink PWH2004 (Abocom5205)Gabor Juhos2010-09-274-0/+111
| | | | | | | | | | | The attached patch adds a preliminary support for Prolink PWH2004 board (Ralink RT305x based). LAN and flash appear to work. However, the USB port and WLAN I have not managed to activate properly yet, but that problem appears to be present with other rt305x targets as well(?). Signed-off-by: Esa Hyytia <esa at netlab.tkk.fi> SVN-Revision: 23129
* ramips: add support for Sparklan WCR-150GN boardGabor Juhos2010-08-154-0/+76
| | | | | | | | | | | This patch adds support for Sparklan WCR-150GN board. Network configuration should be tweaked to make it work fully. The reason it's not in this patch is that ramips target should be modified to support different /etc/config/network files for different boards. Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 22658
* ramips: register ethernet device on the RT-N15Gabor Juhos2010-07-151-0/+8
| | | | SVN-Revision: 22213
* ramips: add generic ethernet device for the RT288xGabor Juhos2010-07-152-0/+44
| | | | SVN-Revision: 22212
* ramips: add mdio_cfg configuration for the ethernet driverGabor Juhos2010-07-153-0/+86
| | | | SVN-Revision: 22211
* ramips: Fix bridging in ramips ethernet driverGabor Juhos2010-07-131-1/+1
| | | | | | | | | | | | | | | | | | Bridging between the ramips ethernet driver and rt2800pci was somewhat broken. Frames received by the ethernet driver which were passed to the wifi driver for transmission were sometimes corrupted or sent out with huge delays. The reason for this is the missing assignment of skb->tail in the ramips ethernet driver's rx path resulting in skb->tail pointing to skb->data. Since skb->tail is used by mac80211 it writes into skb->data which messes up the frames content. Fix this by using skb_put to correctly set skb->len and skb->tail. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> SVN-Revision: 22172
* ramips: protect GPIO register access with a spinlockGabor Juhos2010-07-131-1/+11
| | | | SVN-Revision: 22171
* Fix ramips build when CONFIG_RALINK_DEV_GPIO_BUTTONS is not set.John Crispin2010-05-311-1/+1
| | | | | | Signed-off-by: Helmut Schaa SVN-Revision: 21643
* ramips: merge slab patchGabor Juhos2010-05-282-0/+2
| | | | SVN-Revision: 21607
* ramips: use COMMAND_LINE_SIZE directlyGabor Juhos2010-05-281-1/+1
| | | | SVN-Revision: 21606
* ramips: use KEY_RESTART and KEY_WPS_BUTTON code for the appropriate buttonsGabor Juhos2010-04-225-9/+9
| | | | SVN-Revision: 21083
* ramips: annotate device register function prototypes with __initGabor Juhos2010-03-311-2/+2
| | | | SVN-Revision: 20627
* ramips: register wifi device for the RT2880 based boardsGabor Juhos2010-03-312-0/+3
| | | | SVN-Revision: 20625
* ramips: add wifi device for the RT2880 as wellGabor Juhos2010-03-312-0/+27
| | | | SVN-Revision: 20624
* ramips: register wifi device on the rt305x based boardsGabor Juhos2010-03-304-0/+4
| | | | SVN-Revision: 20616
* The ralink rt305x board has a wireless card that can be used with the ↵John Crispin2010-03-302-0/+27
| | | | | | rt2800pci driver (it does not work yet but basically should). Hence, register the appropriate platform device to allow developing/testing the rt2800pci driver. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> SVN-Revision: 20599
* Fix the base address of the wireless card. Otherwise it is not possible to ↵John Crispin2010-03-301-1/+1
| | | | | | register a platform wireless device as it overlaps with something else. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> SVN-Revision: 20596
* ramips_eth: cleanup mac_address changingGabor Juhos2010-01-311-19/+12
| | | | SVN-Revision: 19464
* ramips_eth: update register offsetsGabor Juhos2010-01-311-8/+8
| | | | SVN-Revision: 19463
* ramips_eth: pass sys_clk via platform_dataGabor Juhos2010-01-313-2/+5
| | | | SVN-Revision: 19462
* ramips_eth: add helper functions to {ed,dis}able interruptsGabor Juhos2010-01-311-6/+21
| | | | SVN-Revision: 19446
* ramips_eth: remove unnecessary typecastsGabor Juhos2010-01-311-2/+2
| | | | SVN-Revision: 19445
* ramips_eth: simplify tx_next computationGabor Juhos2010-01-311-5/+2
| | | | SVN-Revision: 19444
* ramips_eth: simplify tx descriptor initializationGabor Juhos2010-01-311-3/+2
| | | | SVN-Revision: 19443
* ramips_eth: pass 'raeth_priv' struct directly to dma specific functionsGabor Juhos2010-01-311-39/+35
| | | | SVN-Revision: 19442
* ramips_eth: convert to use netdev_opsGabor Juhos2010-01-311-6/+12
| | | | SVN-Revision: 19440
* ramips_eth: fix invalid register writesGabor Juhos2010-01-301-4/+5
| | | | SVN-Revision: 19417
* ramips_eth: move memset call out from the loopGabor Juhos2010-01-301-1/+1
| | | | SVN-Revision: 19416
* ramips_eth: header file cleanupGabor Juhos2010-01-301-144/+146
| | | | SVN-Revision: 19415
* ramips_eth: coding style cleanupGabor Juhos2010-01-301-54/+66
| | | | SVN-Revision: 19414
* ramips: register gpio buttons on the Fonera 2.0N boardGabor Juhos2010-01-302-0/+27
| | | | SVN-Revision: 19413
* ramips: register gpio buttons on the WHR-G300N boardGabor Juhos2010-01-302-1/+45
| | | | SVN-Revision: 19412
* ramips: register gpio buttons on the V22RW-2x2 boardGabor Juhos2010-01-302-1/+26
| | | | SVN-Revision: 19411
* ramips: register gpio buttons on the DIR-300 revB boardGabor Juhos2010-01-302-1/+26
| | | | SVN-Revision: 19410
* ramips: fix wrong base addresses for the RT288xGabor Juhos2010-01-301-4/+5
| | | | SVN-Revision: 19409
* ramips: include 'linux/leds.h' from 'dev-gpio-leds.h'Gabor Juhos2010-01-307-8/+2
| | | | SVN-Revision: 19408
* ramips: rename dev_gpio_leds.h to dev-gpio-leds.hGabor Juhos2010-01-307-6/+6
| | | | SVN-Revision: 19407
* ramips: cleanup WZR-AGL300NH board support fileGabor Juhos2010-01-301-33/+9
| | | | SVN-Revision: 19406
* ramips: register gpio-buttons on the RT-N15 boardGabor Juhos2010-01-302-0/+26
| | | | SVN-Revision: 19405
* ramips: add common gpio-buttons deviceGabor Juhos2010-01-304-1/+93
| | | | SVN-Revision: 19404
* ramips: register rtl8366s device on the RT-N15 boardGabor Juhos2010-01-301-2/+21
| | | | SVN-Revision: 19403
* ramips: sanitize return value of ramips_gpio_getGabor Juhos2010-01-301-1/+1
| | | | SVN-Revision: 19401
* ramips: update mips multi-machine stuffGabor Juhos2010-01-309-59/+17
| | | | SVN-Revision: 19400
* add initial support for the WZR-AGL300NH - patch by Joonas Lahtinen ↵Jo-Philipp Wich2010-01-245-0/+119
| | | | | | <joonas.lahtinen@gmail.com> SVN-Revision: 19321
* ramips: register ethernet device on the WHR-G300N and V22RW-2x2 boardsGabor Juhos2009-10-302-2/+2
| | | | SVN-Revision: 18229
* missing header file changes, and fix mtu valueJohn Crispin2009-10-302-1/+2
| | | | SVN-Revision: 18220
* fixes rx path for eth, spinlock it, increases buffer size, board now ↵John Crispin2009-10-291-28/+23
| | | | | | survives ping -f SVN-Revision: 18212
* hopefully fixes dma issues seen on ethernet driver when under high loadJohn Crispin2009-10-291-2/+7
| | | | SVN-Revision: 18203
* ramips: move 'arch/mips/include/asm/mach-ralink/eth.h' to ↵Gabor Juhos2009-10-262-1/+1
| | | | | | 'drivers/net/ramips_eth.h' SVN-Revision: 18176