aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for ALFA Network AX1800RMPiotr Dymacz2023-09-111-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6 (AX1800) router, based on MediaTek MT7621A + MT79x5D platform. Specifications: - SOC: MT7621A (880 MHz) - DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK) - Flash: 16 MiB SPI NOR (EN25QH128A-104HIP) - Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch) - Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN) (MT7905DAN doesn't support background DFS scan/BT) - LED: 6x green, 1x green/red - Buttons: 2x (reset, WPS) - Antenna: 4x external, non-detachable omnidirectional - UART: 1x 4-pin (2.54 mm pitch, J4, not populated) - Power: 12 V DC/1 A (DC jack) MAC addresses: LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2) WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3) 2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label) 5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa) Flash instructions for web-based U-Boot recovery: 1. Power the device with WPS button pressed and wait around 10 seconds. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'recovery' image. The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe' mode available which allows alternative upgrade method: 1. Run device in 'failsafe' mode and change password for default user. 2. SSH to the device, transfer 'sysupgrade' image and perform upgrade in forced mode, without preserving settings: 'sysupgrade -n -F ...'. Other notes: If you own early version of this device, the vendor firmware might refuse OpenWrt image because of missing custom header. In that case, ask vendor's customer support for stock firmware without custom header support/requirement. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit f1aaa267f0ea18ffe5840f3ce46a48be123d2f62)
* ramips: improve Xiaomi mi-mini indicationsIvan Pavlov2023-08-151-5/+4
| | | | | | | Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com> (cherry picked from commit 54e5e396c59948224dfb8ccf7aa8afe11462f647)
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-031-0/+151
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5)
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-023-0/+480
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
* ramips: fix lan leds for Wavlink WL-WN535K1Davide Fioravanti2023-06-251-2/+2
| | | | | | | | | | Previously both lan1 and lan2 leds were wrongly labelled as lan2. Moreover they were connected to the wrong lan port. Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1") Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit c71dada92654a53c63bbc5bebcc40fe924750ed7)
* ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)Kim DoHyoung2023-06-252-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr> (cherry picked from commit 0bbd5699c81d6887c4d895e85b56d8c23b1211ec)
* ramips: Add support for Beeline SmartBox TURBO+Maximilian Weinmann2023-06-171-0/+248
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router. Device specification -------------------- SoC Type: MediaTek MT7621AT (880 MHz, 2 cores) RAM (Nanya NT5CC64M16GP): 128 MiB Flash (Macronix MX30LF1G18AC): 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615N): a/n/ac, 4x4 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) USB ports: 1xUSB3.0 Buttons: 2 button (reset, wps) LEDs: Red, Green, Blue Zigbee (EFR32MG1B232GG): 3.0 Stock bootloader: U-Boot 1.1.3 Power: 12 VDC, 1.5 A Installation (fw 2.0.9) ----------------------- 1. Login to the web interface under SuperUser (root) credentials. Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the device written on the backplate stick. 2. Navigate to Setting -> WAN. Add: Name - WAN1 Connection Type - Static IP Address - 172.16.0.1 Netmask - 255.255.255.0 Save -> Apply. Set default: WAN1 3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add: Protocol - SSH Port - 22 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN Interface - WAN1 Save ->Apply Add: Protocol - HTTP Port - 80 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN interface - WAN1 Save -> Apply 4. Set up your PC ethernet: Connection Type - Static IP Address - 172.16.0.2 Netmask - 255.255.255.0 Gateway - 172.16.0.1 5. Connect PC using ethernet cable to the WAN port of the router 6. Connect to the router using SSH shell under SuperUser account 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface under admin account 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 171.16.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses (fw 2.0.9) ------------------------ +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:e8 | | WAN | label + 1 | *:e9 | | 2g | label + 4 | *:ec | | 5g | label + 5 | *:ed | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 Factory image format -------------------- +---+-------------------+-------------+--------------------+ | # | Offset | Size | Description | +---+-------------------+-------------+--------------------+ | 1 | 0x0 | 0x200 | Tag Header Factory | | 2 | 0x200 | 0x100 | Tag Header Kernel1 | | 3 | 0x300 | 0x100 | Tag Header Kernel2 | | 4 | 0x400 | SIZE_KERNEL | Kernel | | 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) | +---+-------------------+-------------+--------------------+ Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org> (cherry picked from commit 8fcfb21b16e7537b9a871a1f67cb218c6be93149)
* ramips: mt7621-dts: move wan port to gmac1 YunCore FAP-640Volodymyr Puiul2023-06-111-7/+20
| | | | | | | | move wan port to gmac1 to achieve 2Gbps CPU bandwidth between wan and lan on YunCore FAP-640 Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com> (cherry picked from commit 47c2d50c0312412582fff7950b843d619400da9f)
* ramips: fix button definitions for Zyxel WSM20Thomas Schröder2023-06-101-2/+2
| | | | | | | | | Setting the events of the WPS and LED buttons to the best matching values based from the documentation: <https://openwrt.org/docs/guide-user/hardware/hardware.button#procd_buttons> Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com> (cherry picked from commit b0120f7c8bb35088f298f00eb4a630f62fb4183f)
* ramips: mt7621: fix Xiaomi Router 3G/Pro LEDsDENG Qingfang2023-05-202-20/+53
| | | | | | | | | | The PHY name has been changed to "mt7530-0" since IRQ support was added to MT7530 driver. Fixes: f9cfe7af1f1f ("kernel: backport MT7530 IRQ support") Signed-off-by: DENG Qingfang <dqfext@gmail.com> (node names, added color, function+function-enumerator properties) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: rename to D-Team Newifi D2 and Lenovo Newifi D1Arınç ÜNAL2023-05-182-2/+2
| | | | | | | Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1. Let's not make naming exceptions because of marketing whims. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for TOZED ZLT S12 PROArınç ÜNAL2023-05-181-0/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: Fix Wireless Frequencies for HYC-G920Muhammad AL-Qadhy2023-05-181-0/+2
| | | | | | Fix wireless frequencies to show correct wireless interfaces. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
* ramips: remove device tree legacy compatibilityNick Hainke2023-05-121-60/+0
| | | | | | | We switched to 5.15 kernel, so we don't need to maintain 5.10 compatibility anymore. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: add support for Linksys RE7000Christoph Krapp2023-05-091-0/+154
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com>
* ramips: fix dts file name for SNR-CPE-ME1Maximilian Weinmann2023-05-081-0/+0
| | | | | | | | | Rename file mt7621_snr_snr-spe-me-1.dts Fixes: #12562 Fixes: ecdb248 ("ramips: add support for SNR-CPE-ME1") Tested-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: add support for SNR-CPE-ME1Maximilian Weinmann2023-05-071-0/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 16 MiB (GD25Q128CSIG) - WLAN : 2.4 GHz (MediaTek MT7603EN) 5 GHz (MediaTek MT7610EN) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (in SoC) - USB : 3.0 x1 - UART : through-hole on PCB - [J4] 3.3V, RX, TX, GND (57600n8) - Power : 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME1 to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: mt7621: rename Asus RT-AC57U to v1Felix Baumann2023-05-061-2/+2
| | | | | | rename RT-AC57U to avoid confusion with unsupported revisions 2 and 3 Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-023-48/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: TP-Link EC330-G5u v1: switch to mac-address-asciiMikhail Zhilkin2023-04-291-0/+26
| | | | | | | | | | | | | The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd in ascii format. This commit makes the router use of "mac-address-ascii" in dts. After the change: 1. All MAC addresses are explicitly assigned in dts (the workarounds in network scripts are no longer needed); 2. gmac0 (eth0) MAC address is no longer random. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for D-Link DAP-1620 B1Rani Hod2023-04-291-0/+158
| | | | | | | | | | | | | | | | | | | | | | | | | The DAP-1620 rev B is a wall-plug AC1300 repeater. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI NOR - MT7615DN 2x2 802.11n +2x2 802.11ac (DBDC) - Ethernet: 1 port 10/100/1000 - Status LEDs (1x red+green) - LED RSSI bargraph (2x green, 1x red+green) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tail -c+117 DAP1620B1_FW212B03.bin | \ openssl aes-256-cbc -d -md md5 -out decrypted.bin \ -k 905503a4e0c3cd3c1ce062246de427a68962347e - flash decrypted.bin via D-Link Web Recovery Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: mt7621: add support for ZyXEL WSM20Andreas Böhler2023-04-291-0/+233
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device
* ramips: reduce Archer AX23 / MR70X SPI-frequencyDavid Bauer2023-04-272-2/+2
| | | | | | | | | | | | | | It was brought to attention the Archer AX23 v1 fails to read jffs2 data from time to time. While this is not reproducible on my unit, it is on others. Reducing the SPI frequency does the trick. While it worked with at lest 40 MHz, opt for the cautious side and choose a save frequency of 25 MHz. Apply the same treatment to the Mercusys MR70X which uses a similar design just in case. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix green LED for D-Link DAP-X1860Sebastian Schaper2023-04-241-4/+9
| | | | | | | | | | | It was found this device uses a single tri-color power/status LED rather than individual red/orange LEDs, which also supports green. Add GPIO for green color and use with `boot` and `running` aliases. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Cudy X6 fixes / improvementsFelix Baumann2023-04-241-14/+15
| | | | | | | | | | | | | | | | | | | | | | - Correct WiFi MACs, they didn't match oem firmware - Move nvmem-cells to bdinfo partition and remove &bdinfo reference - Add OEM device model name R13 to SUPPORTED_DEVICES This allows sysupgrading from Cudy's OpenWrt fork without force - Label red_led and use it during failsafe mode and upgrades MAC addresses as verified by OEM firmware: use address source LAN b4:4b:d6:2d:c8:4a label WAN b4:4b:d6:2d:c8:4b label + 1 2g b4:4b:d6:2d:c8:4a label 5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [read wifi mac from flash offset] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: MSG1500 X.00: switch to mac-address-ascii dtsChukun Pan2023-04-211-10/+29
| | | | | | | | The Config partition of some machines is special, and the openwrt script cannot read the protest_lan_mac correctly. This problem can be solved by reading the mac address (ascii) in dts. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add Xiaomi RA75 red signal ledOleksandr Zharov2023-04-171-0/+11
| | | | | | | | | | | | | | | | | RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes: Indicator "System": GPIO0: blue GPIO2: amber Indicator "Signal": GPIO44: blue GPIO37: amber GPIO46: red All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by default, so it needs additional pin control change in devicetree to be operational. Verified on my RA75. Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
* ramips: lower re305-v3 spi-max-frequencyJoe Mullally2023-04-081-1/+1
| | | | | | | | | | | | | Fix flash I/O instability observed in newer devices with cFeon QH64A-104HIP (detected as en25qh64). Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91 Reported-by: Dimitri Souza <dimitri.souza@gmail.com> Tested-by: Dimitri Souza <dimitri.souza@gmail.com> Signed-off-by: Joe Mullally <jwmullally@gmail.com> [alter commit-message - target master] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: define remapping-range for DAP-X1860David Bauer2023-04-081-0/+7
| | | | | | | | | Prevent the BBT translation layer from remapping the UBI used for storing rootfs. Explicitly define the number of blocks reserved for remapping. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for OrayBox X1Bin We2023-04-021-0/+129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N. Specifications: SoC: MediaTek MT7628N (580MHz) RAM: 64 MiB Flash: 16 MiB NOR (Winbond W25Q128JVSIQ) Wireless: 802.11b/g/n 2x2 2.4GHz (Built In) Ethernet: 1x 100Mbps only USB: 1x USB Type-A 2.0 Host Port Button: 1x "Reset" button LED: 1x Blue LED + 1x Red LED + 1x White LED Power: 5V Micro-USB input Manufacturer Page: https://pgy.oray.com/router/x1.html/parameter Flash Layout: 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "kpanic" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000fe0000 : "firmware" 0x000000fe0000-0x000000ff0000 : "bdinfo" 0x000000ff0000-0x000001000000 : "reserve" Install via SSH: Original firmware is based on OpenWRT, but SSH is not start by default, You should enable it first 1. Login into web admin (10.168.1.1), default password is 'admin' 2. Open the following link, and the result should be {"code":0}; SSH is now started, username is root, password is same as web admin password http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1 4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware Signed-off-by: Bin We <me@udp.pw>
* ramips: Add support for CJ-Hello HYC-G920Muhammad AL-Qadhy2023-04-011-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
* ramips: mt7621: ASUS RT-AX53U add NMBM, nest firmwareFelix Baumann2023-04-011-7/+26
| | | | | | | | | | | | Nests kernel and ubi into firmware partition in-order to be compatible with OEM firmware. This allows restoring oem firmware from a backup of firmware2. Add jffs2 partition which is present in the oem firmware. Add support for mediatek NMBM (wear leveling on newer mediatek devices). Exclude UBI partition from NMBM management. Continues PR #10685. Tested-by: Felix Baumann <felix.bau@gmx.de> Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: add support for Keenetic Lite III rev. AAlexey Bartenev2023-03-271-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General specification: SoC Type: MediaTek MT7620N (580MHz) ROM: 8 MB SPI-NOR (W25Q64FV) RAM: 64 MB DDR (EM6AB160TSD-5G) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Buttons: 3 button (POWER, RESET, WPS) Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT) Bootloader: U-Boot 1.1.3 Power: 9 VDC, 0.6 A MAC in stock: |- + | | LAN | RF-EEPROM + 0x04 | | WLAN | RF-EEPROM + 0x04 | | WAN | RF-EEPROM + 0x28 | OEM easy installation 1. Use a PC to browse to http://my.keenetic.net. 2. Go to the System section and open the Files tab. 3. Under the Files tab, there will be a list of system files. Click on the Firmware file. 4. When a modal window appears, click on the Choose File button and upload the firmware image. 5. Wait for the router to flash and reboot. OEM installation using the TFTP method 1. Download the latest firmware image and rename it to klite3_recovery.bin. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.1.2 and subnet mask 255.255.255.0. 5. Power up the router while holding the reset button pressed. 6. Wait approximately for 5 seconds and then release the reset button. 7. The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me>
* ramips: mt7621: enable unused PCIe port to fix potential boot failureShiji Yang2023-03-264-16/+0
| | | | | | | | | | | | | One user reported that his SIMAX1800T couldn't boot like the others. After debugging, I found that this was caused by the disabled PCIe port. I cannot reproduce this issue on my SIMAX1800T. But when I disabled pcie2 on the ASUS RT-AC57U, I got the same result. It seems that disabling these unused PCIe ports on some mt7621 revisions will cause PCIe to fail to initialize. So we'd better to re-enable them on all related mt7621 devices. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Mercusys MR70XDavid Bauer2023-03-241-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: Winbond W25Q128JV (SPI-NOR 16MB) - WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC) - UART: >TX RX GND 3v3 (115200 8N1, J1) Do not connect 3v3. TX is marked with an arrow. Installation ============ Flash factory image. This can be done using stock web ui. Revert to stock firmware ======================== Flash stock firmware via OEM Web UI Recovery mode. Web UI Recovery method ====================== 1. Unplug the router 2. Plug in and hold reset button 5~10 secs 3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0 4. Flash image with web browser to 192.168.1.1 Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: cudy wr1300v2 reduce SPI freq to 40000000Óscar García Amor2023-03-201-2/+1
| | | | | | | | | Cases have been reported in which certain devices do not boot correctly or have errors. After various tests by users who have such errors it has been concluded that the SPI frequency should be reduced to 40Mhz, at this speed it appears that all devices work correctly. Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
* ramips: add support for TP-Link Archer AX23 v1David Bauer2023-03-151-0/+203
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR () WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Upload the factory image using the Web-UI. Web-Recovery ------------ The router supports a HTTP recovery mode by holding the reset-button when powering on. The interface is reachable at 192.168.0.1 and supports installation using the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for SNR-CPE-ME2-SFPAleksey Nasibulin2023-03-081-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
* ramips: fix wrong pcie port number for Arcadyan WE420223-99Mikhail Zhilkin2023-03-041-1/+1
| | | | | | | | | | | | | Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15 kernel on Arcadyan WE420223-99 (KPN Experia WiFi). This changes port from pcie0 to pcie1. [1.331556] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK) [1.345299] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [1.359116] mt7621-pci 1e140000.pcie: PCIE1 enabled Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for D-Link Dir-853 A1Hang Zhou2023-03-041-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7621AT * RAM: 256MB (NT5CC64M16GP-DI) * Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver) * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * Ethernet: 4x1000M LAN, 1x 1000M WAN * LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons: Reset,WPS, Wifi * Serial interface: on board but not populated, pinout (from the DC jack side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600, settings are 8 data bits, no parity bit, one stop bit, and no flow control. Stock flash layout: ``` GD25Q128C(c8 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "Config2" 0x000000060000-0x000000fb0000 : "Kernel" 0x000000fb0000-0x000001000000 : "Private" ``` The kernel partition will be replaced with the OpenWrt image, the other partitions are left untouched. "Config2" seems to be the config storage used by the stock firmware. "Private" is a 320kB empty JFFS2 partition that comes with the stock firmware. One can get a larger space for OpenWrt by merging it with "Kernel". OpenWrt flash layout: ``` 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "u-boot-env" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000060000 : "config2_stock" 0x000000060000-0x000000fb0000 : "firmware" 0x000000fb0000-0x000001000000 : "private_stock" ``` The OpenWrt image must have 96 bytes of padding in the header. MAC addresses on OEM firmware: | | location on the flash | notes | |------ |----------------------- |---------- | | lan (eth2) | factory + 0xe000 | on label | | wan (eth3) | factory + 0xe006 | | | 2.4g (rax0) | not on flash | lan + 1 | | 5g (ra0) | not on flash | lan + 2 | Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in the u-boot-env partition, but they are not used. OpenWrt calculates Wifi Mac addresses based on the LAN Mac. Flash and test instructions: Flash the encrypted image (available in the OpenWrt forum) through the stock D-Dink web interface. 1. Open the case, and solder the 4-pin header near the WAN port. 2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC. 3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with the settings mentioned above. 4. Setup a TFTP server on your PC that can serve `xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`. 5. Connect any LAN port to your PC and set a static IPv4 address to 192.168.0.101 (netmask 255.255.255.0). 6. Power on the device and keeps pressing 1 until you see the prompt. 7. Use default IP addresses and enter the file name accordingly, then hit enter. 8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1, you need to change your PC network adapter to use DHCP in order to access LUCI. 9. So far, the OpenWrt runs in RAM and the flash contents are not touched. You can try OpenWrt without having to overwrite the stock firmware, a reboot clears all changes. 10. Optionally, backup the stock firmware (the "firmware" partition) in Luci. 11. To permantly install OpenWrt to the device , click on "System -> Backup/Flash Firmware" in Luci and flash `xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin` Known problems: * WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network, you need to config it manually in LUCI. * If you see jffs2 related warnings/errors after updating from the stock web interface, you need to do a reset in LUCI. The error will be gone after a cold reboot. Signed-off-by: Hang Zhou <929513338qq@gmail.com>
* treewide: remove label = "cpu" from DSA dt-bindingArınç ÜNAL2023-02-261-1/+0
| | | | | | | This is not used by the DSA dt-binding, so remove it from all devicetrees. Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: correct the PCIe port number for some mt7621 devicesFelix Baumann2023-02-252-2/+2
| | | | | | | | | | | | | | | | | | | | MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe port will cause the PCIe NIC to not work properly. This commit fixes the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5. According to bootlog, MT7612E (5GHz) is connected to pcie0, and MT7603E (2GHz) is connected to pcie2: [2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) [2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled [2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled ... [3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com> [felix.bau@gmx.de: adjust commit message for Netgear devices] Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: correct the PCIe port number for Zbtlink ZBT-WE1326Shiji Yang2023-02-191-2/+2
| | | | | | | | | | | | | | | | | MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe port will cause the PCIe NIC to not work properly. This commit fixes the wrong port numbers on Zbtlink ZBT-WE1326. According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and MT7603E (2 GHz) is connected to pcie2: [4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK) [4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled [4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled ... [4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Huasifei WS1208V2Arınç ÜNAL2023-02-181-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a Quectel RM520N-GL cellular modem which supports QMI and MBIM modes. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI Flash - MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN - Quectel RM520N-GL Cellular Modem - 2 WLAN & 4 Cellular Antennas - 5 Gigabit Ethernet Ports - 1 USB 2.0 port - 1 PCI-E Slot - 1 M.2 slot - 1 SIM card slot - 1 SD card slot Installation: - Install sysupgrade image via ROOter OS. TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for Senao Engenius EPG600Michael Pratt2023-02-181-0/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EPG600 Engenius EPG600 is an indoor wireless router with 1 Gb ethernet switch, dual-band wireless, internal antenna plates, USB, and phone lines (not supported) this board is a Senao device: the hardware is equivalent to EnGenius ESR600 (except for phone lines) the software is Senao SDK which is based on openwrt and uboot which uses the legacy Senao header with Vendor / Product IDs to verify the firmware upgrade image. **Specification:** - MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2 - RT5592N WLAN PCI chip, 5 GHz, 2x2 - QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 64 MB RAM NT5TU32M16 - UART console J2, populated - USB 2.0 port direct to SOC - 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line - 3 buttons reset, wps, "reg" (registeration) - 4 antennas internal omni-directional plates NOT YET SUPPORTED: VoIP - Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data - Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins) **MAC addresses:** MAC address labeled as MAC ADDRESS MACs present in both wifi cal data and uboot environment eth0.1/phy1 ---- *:82 rf 0x4 phy0 ---- *:83 factory 0x4 eth0.2 MAC *:b8 "wanaddr" **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.0.1 username and password 'admin' Navigate to gear icon, "Device Management", "Tools" select the factory.dlf image Upload and verify checksum Method 2: Serial to upload initramfs: Follow directions for TFTP recovery upload and boot initramfs and do a sysupgrade **TFTP recovery:** Requires UART serial console, reset button does nothing rename initramfs-kernel.bin to 'uImageEPG600' make available on TFTP server at 192.168.99.8 power board, interrupt boot with "4" execute `tftpboot` and `bootm` (with the load address) **Return to OEM:** Images from OEM are provided, but not compatible with openwrt sysupgrade. So it must be modified. Alternatively, back up all mtd partitions before flashing **Note on switch registers:** The necessary registers needed for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by using the following lines in the switch driver ar8327.c in the function 'ar8327_hw_config_of' where 'qca,ar8327-initvals' is parsed from DTS before the new register values are written: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE)); pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE)); pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: fix wrong pcie port number for Arcadyan devicesMikhail Zhilkin2023-02-171-1/+1
| | | | | | | | | | | Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15 kernel. This changes port from pcie0 to pcie1 in dtsi. [1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK) [1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ASUS RT-AX54Karl Chan2023-02-121-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX54 (AX1800S/HP,AX54HP) - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 4 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x POWER (blue, configurable) 1x LAN (blue, configurable) 1x WAN (blue, configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Karl Chan <exkc@exkc.moe>
* ramips: fix dts whitespaceFelix Baumann2023-02-096-15/+15
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2Arınç ÜNAL2023-02-031-1/+1
| | | | | | | | The phy-mode property must be defined on the MAC instead of the PHY. Define phy-mode under gmac1 which the external phy is connected to. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-WallArınç ÜNAL2023-02-031-1/+0
| | | | | | | | | | The correct compatible string for the multi-chip module MT7530 switch in MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the property on TP-Link EAP615-Wall which will default to the said string. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 15:23:03 +0000