aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add label-mac for TL-MR3020 v3David Bauer2021-08-281-0/+1
| | | | | | | | The TP-Link TL-MR3020 v3 only has a single MAC address assigned for ethernet LAN as well as WiFi. This MAC address is also printed on the casing. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: enable fast-read for TL-MR3020 v3David Bauer2021-08-281-0/+1
| | | | | | | | The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast read instruction. Add the required DT property in order to enable usage of this property. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: increase SPI frequency for TL-MR3020 v3David Bauer2021-08-281-1/+1
| | | | | | | The GigaDevices GD25Q64B supports higher SPI clocks than 10 MHz. While 100 MHz do not work reliably, 50 MHz works without issues. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix input type for TL-MR3020 v3David Bauer2021-08-281-0/+2
| | | | | | | | | The modec{1,2} keys are actually switches. Add the respective DTS properties to avoid accidental activation of failsafe mode. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: expose ephy leds for miwifi-miniDavid Yang2021-08-251-4/+20
| | | | | | | | Give users more control by exposing ephy leds. Signed-off-by: David Yang <mmyangfl@gmail.com> [remove execute bit on 01_leds, add status for gpio2] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: lock u-boot partition and unlock u-boot-env for miwifi-miniDavid Yang2021-08-251-1/+1
| | | | | | | | Generally u-boot should keep read-only to avoid mis-overwriting and bricking the device, but u-boot-env could be safely modified with u-boot setenv tool. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: increase flash freq for miwifi-miniDavid Yang2021-08-251-1/+2
| | | | | | | The flash is Winbond 25Q128. As it has large rom, better to increase flash frequency to 70MHz according to the flash spec and enable fast-read. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: add support for D-Link DAP-1325-A1Giovanni Cascione2021-08-251-0/+139
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300) Specifications: - SoC: 580Mhz MT7628NN - RAM: 64MB, DDR2 SDRAM - Storage: 8MB, SPI (W25Q64JVSSIQ) - Ethernet: 1x 10/100 LAN port - WIFI: 2.4 GHz 802.11bgn - LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x) - Buttons: Reset, WPS - UART: Serial console (57600, 8n1) Row of 4 holes near LAN port, starting from square hole: 3.3V, TX,RX,GND - FCC ID: fccid.io/KA2AP1325A1/ Installation: Failsafe UI Firmware can be uploaded with Failsafe UI web page: - turn device off - press and hold reset button - turn device on - keep holding reset until red wifi strength led turns on (ab. 10sec) - connect to device through LAN port PC must be configured with static ip (192.168.0.x) - connect to 192.168.0.50 - select image to be flashed and upload. Device will reboot after successful update Serial port/TFTP server - Connect through serial connectors on PCB (e.g. with teraterm) - Set up a TFTP server, and connect through LAN with static IP - Put image file in the root of the server - Boot the device and select '2' at U-Boot startup - Set device IP, server IP and image file name - Start upload and flash Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com> [fix whitespaces in DTS, convert to nvmem, add mtd-eeprom] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for DomyWifi DM202/DM203/DW22DShiji Yang2021-08-254-0/+213
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7620A + MT7610E * ROM: 16 MiB spi flash (W25Q128FVSG) * RAM: 128 MiB DDR2 (W971GG6KB-25) * WAN: 10/100M *1 * LAN: 10/100M *4 * USB: Type-A USB2.0 *1 * SD: MicroSD *1 * Button: Reset *1 * Antennas: 2.4 GHz *2 + 5 GHz *1 * TTL Baudrate: 57600 * U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3 Installation: * Web UI Update 1. Open http://192.168.10.1/upgrade.html in the browser. 2. Rename firmware to a short name like firmware.bin and then upload it. 3. Fill in the password column with the following content: password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware * TFTP + U-Boot 1. Connect device with a TTL cable. 2. Press "2" when booting to select "Load system code then write to Flash via TFTP". 3. Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Motorola MWR03Shiji Yang2021-08-251-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7628AN + MT7612E * ROM: 8 MiB Flash * RAM: 64 MiB DDR2 * WAN: 10/100M *1 * LAN: 10/100M *3 * Button: Reset *1 * LEDs: orange *1, white *1 * Antennas: 2.4 GHz *2 + 5 GHz *2 * TTL Baudrate: 57600 * TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100 MAC addresses as verified by OEM firmware: use address source 2g *:d8 factory 0x0004 (label) 5g *:d9 factory 0x8004 LAN *:d7 factory $label -1 WAN *:da factory $label +2 Installation (TFTP + U-Boot): * Connect device with a TTL cable and open a serial session by PuTTY. * Press "2" when booting to select "Load system code then write to Flash via TFTP". * Configure the IP of local host server. * Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix DTS line endings, fix label MAC address, adjust status LED names, convert mtd-mac-address-increment to mac-address-increment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add new flash layout support to Phicomm K2Shiji Yang2021-08-242-2/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Descriptions： Phicomm K2 (PSG1218) got a new "permanent_config" partition after update firmware to v22.5. This partition located in front of the firmware partition, same as The Phicomm K2P and K2G. Due to this change the new bootloader can't load previous firmware any more. This commit is aimed at add support for Phicomm K2 which official firmware version is 22.5.x or newer. For which runs old firmware version, just update OpenWrt that has a prefix of "k2-v22.4". For uniform naming, this commit also changed the model name PSG1218 to a more recognizable name K2, refer to Phicomm K2G, K2P K2T. OpenWrt selection table: official firmware version OpenWrt v22.4.x.x or older phicomm_k2-v22.4 v22.5.x.x or newer phicomm_k2-v22.5 Installation: Same as Phicomm K2G, K2P, PSG1208. a. TFTP + U-Boot b. Open telnet by some web page vulnerability (Search Baidu by key words "K2 telnet"), and then we can upload firmware image to /tmp and write it to firmware partition with mtd instruction. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [rebase, add/harmonize version in model variables, fix version typo in commit message, wrap commit message properly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: move Phicomm MAC address setup to DTSIAdrian Schmutzler2021-08-244-41/+15
| | | | | | The setup is the same for all devices, so move it up one level. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix ethernet MAC address on Omega2Michael Siegenthaler2021-08-211-3/+3
| | | | | | | | | | | | | | | | According to https://docs.onion.io/omega2-docs/mac-address.html, 0x28 is the correct location to read the address on Onion Omega 2(+) devices. This fixes a regression introduced by commit 77e850fe76e3 ("ramips: tidy up MAC address setup for Linkit Smart and Omega2"), which was a cleanup that intended to preserve existing behavior. In my testing with v19.07.7, however, the MAC address determined from the device tree takes precedence over the one set by 02_network, so the aforementioned commit actually changed the behavior. Signed-off-by: Michael Siegenthaler <msiegen@google.com> [Adapt patch to nvmem usage] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: convert mtd-mac-address to nvmem for UniElec devicesAdrian Schmutzler2021-08-207-18/+80
| | | | | | | | | Convert this series by moving the definitions to the individual devices. Now all devices on ramips are converted. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant nvmem definitionsAdrian Schmutzler2021-08-2017-170/+0
| | | | | | | | Due to use of a script when migrating from mtd-mac-address, a few of the definitions are redundant in DTSI and DTS files. Remove those. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix indent in DTS for GL.iNet VIXMINI/microuter-N300Adrian Schmutzler2021-08-202-2/+2
| | | | | | Use correct indent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert mtd-mac-address to nvmem for D-Link DIR-8xxAdrian Schmutzler2021-08-208-13/+137
| | | | | | | Convert this series by moving the definitions to the individual devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert most mtd-mac-address cases in DTSI to nvmemAdrian Schmutzler2021-08-1847-1021/+938
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert most of the cases from mtd-mac-address to nvmem where MAC addresses are set in the DTSI, but the partitions are only located in the device DTS. This posed some problems earlier, since in these cases we are using partitions before they are defined, and the nvmem system did not seem to like that. There have been a few different resolution approaches, based on the different tradeoffs of deduplication vs. maintainability: 1. In many cases, the partition tables were identical except for the firmware partition size, and the firmware partition was the last in the table. In these cases, the partition table has been moved to the DTSI, and only the firmware partition's "reg" property has been kept in the DTS files. So, the updated nvmem definition could stay in the DTSI files as well. 2. For all other cases, splitting up the partition table would have introduced additional complexity. Thus, the nodes to be converted to nvmem have been moved to the DTS files where the partitioning was defined. 3. For Netgear EX2700 and WN3000RP v3, the remaining DTSI file was completely dissolved, as it was quite small and the name was not really nice either. 4. The D-Link DIR-853 A3 was converted to nvmem as well, though it is just a plain DTS file not taken care of in the first wave. In addition, some minor rearrangements have been made for tidyness. Not covered (yet) by this patch are: * Various unielec devices * The D-Link DIR-8xx family Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add WPS button for newifi d1David Yang2021-08-171-1/+7
| | | | | | This device has a WPS button under WiFi antenna cover, add it to dts. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: mt7628: move mtd-eeprom out of root DTSIAdrian Schmutzler2021-08-1744-9/+90
| | | | | | | | | | | | | | | | | | | | | | | | The mt76x8 subtarget is the only one in ramips that stores the mediatek,mtd-eeprom property directly in the "root" mt7628an.dtsi. This is not optimal for a few different reasons: * If you don't really know it or are used to other (sub)targets, the property will be set somewhat magically. * The property is set based on &factory partition before (if at all) this partition is defined. * There are several devices that have different offset or even different partitions to read from, which will then be overwritten in the DTS files. Thus, definitions are scattered between root DTSI and individual files. Based on these circumstances, the "root" definition is removed and the property is added to the device-based DTS(I) files where needed and applicable. This should be easier to grasp for unexperienced developers and will move the property closer to the partition definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add missing label-mac-device for Xiaomi Mi Router 4A (100M)Fabian Bläse2021-08-051-0/+1
| | | | | | | As both the Mi Router 4A (100M) and the Mi Router 4C use the same label-mac-device, the alias can be moved to the shared dtsi. Signed-off-by: Fabian Bläse <fabian@blaese.de>
* ramips: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-19319-434/+4213
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* treewide: convert mtd-mac-address-increment* to generic implementationAnsuel Smith2021-07-1960-74/+74
| | | | | | | | | | | | | Rework patch 681-NET-add-mtd-mac-address-support to implement only the function to read the mac-address from mtd. Generalize mtd-mac-address-increment function so it can be applied to any source of of_get_mac_address. Rename any mtd-mac-address-increment to mac-address-increment. Rename any mtd-mac-address-increment-byte to mac-address-increment-byte. This should make simplify the conversion of target to nvmem implementation. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ramips: add support for D-Link DIR-853 A3Karim Dehouche2021-07-121-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7621AT * RAM: 256MB * Flash: 128MB NAND flash * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * LAN: 5x1000M * Firmware layout is Uboot with extra 96 bytes in header * Base PCB is DIR-1360 REV1.0 * LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons Reset,WPS, Wifi MAC addresses on OEM firmware: lan factory 0xe000 f4:*:*:a8:*:65 (label) wan factory 0xe006 f4:*:*:a8:*:68 2.4 GHz [not on flash] f6:*:*:c8:*:66 5.0 GHz factory 0x4 f4:*:*:a8:*:66 The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20 x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20 x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Flashing instruction: The Dlink "Emergency Room" cannot be accessed through the reset button on this device. You can either use console or use the encrypted factory image availble in the openwrt forum. Once the encrypted image is flashed throuh the stock Dlink web interface, the sysupgrade images can be used. Header pins needs to be soldered near the WPS and Wifi buttons. The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC. the settings are: Bps/Par/Bits : 57600 8N1 Hardware Flow Control : No Software Flow Control : No Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.101 / 255.255.255.0. Call the recovery page or tftp for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device At the time of adding support the wireless config needs to be set up by editing the wireless config file: * Setting the country code is mandatory, otherwise the router loses connectivity at the next reboot. This is mandatory and can be done from luci. After setting the country code the router boots correctly. A reset with the reset button will fix the issue and the user has to reconfigure. * This is minor since the 5g interface does not come up online although it is not set as disabled. 2 options here: 1- Either run the "wifi" command. Can be added from LUCI in system - startup - local startup and just add wifi above "exit 0". 2- Or add the serialize option in the wireless config file as shown below. This one would work and bring both interfaces automatically at every boot: config wifi-device 'radio0' option serialize '1' config wifi-device 'radio1' option serialize '1' Signed-off-by: Karim Dehouche <karimdplay@gmail.com> [rebase, improve MAC table, update wireless config comment, fix 2.4g macaddr setup] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v2Tee Hao Wei2021-07-111-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
* ramips: mt7628an: remove redundant console setup for bootargsAdrian Schmutzler2021-07-102-8/+0
| | | | | | This is already set in mt7628an.dtsi Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-853-R1Stas Fiduchi2021-07-101-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for router D-Link DIR-853-R1 Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB SPI WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the same time) LAN: 5x1000M LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue USB Blue Buttons Reset,WPS, Wifi MAC addresses: |Interface | MAC | Factory |Comment |------------|-----------------|-------------|---------------- |WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker |LAN |C4:XX:XX:6E:XX:2B| | |Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 | |Wifi (2.4g) |C6:XX:XX:7E:XX:2C| | | | | | | |C4:XX:XX:6E:XX:2E|0x8004 0xe000| | |C4:XX:XX:6E:XX:2F|0xe006 | The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10 f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20 F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Flashing instruction: The Dlink "Emergency Room" Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.101 / 255.255.255.0. Then, power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing Call the recovery page or tftp for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com> [commit title/message improvements, use correct label MAC address, calculate MAC addresses based on 0x4, minor DTS style fixes, add uart2 to state_default, remove factory image, add 2.4g MAC address, use partition DTSI, add macaddr comment in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for minew g1-cAlexander Couzens2021-07-051-0/+146
| | | | | | | | | | | | | | | | | | | | | | The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for Tenbay T-MB5EU-V01David Bauer2021-06-271-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7621 SoC 256M DDR3 16MB BoHong SPI-NOR MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax RGB LED WPS + RESET Button UART on compute module (silkscreened / 115200n8) The router itself is just a board with Power / USB / RJ-45 connectors and DC/DC converters. The SoC and WiFi components are on a daughterboard which connect using two M.2 connectors. The compute module has the model number "T-CB1800K-DM2 V02" printed on it. The main baord has "T-MB5EU V01" printed on it. This information might be useful, as it's highly likely either of these two will be reused in similar designs. The router itself is sold as Tenbay T-MB5EU directly from the OEM as well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a slightly different case. Installation ------------ A Tool for creating a factory image for the Vendor Web Interface can be found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/ As the OEM Firmware is just a modified LEDE 17.01, you can also access failsafe mode via UART while the OS boots, by connecting to UART and pressing "f" when prompted. The Router is reachable at 192.168.1.1 via root without password. Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade using the -n and -F flags. Alternatively, the board can be flashed by attaching to the UART console, interrupting the boot process by keeping "0" pressed while attaching power. Serve the OpenWrt initramfs using a TFTP server with address 192.168.1.66. Rename the initramfs to ax1800.bin. Attach your TFTP server to one of the LAN ports. Execute the following commands. $ setenv ipaddr 192.168.1.67 $ setenv serverip 192.168.1.66 $ tftpboot 0x84000000 ax1800.bin $ bootm Wait for the device to boot. Then transfer the OpenWrt sysupgrade image to the device using SCP and apply sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: ethernet: ralink: move reset of the esw into the esw instead of feAlexander Couzens2021-06-252-4/+4
| | | | | | The esw reset should only done by the esw driver and not by the fe itself. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: use the reset controller api for esw & ephyAlexander Couzens2021-06-254-8/+8
| | | | | | Instead of writing direct into the reset registers. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: fix software reboot failure on HILINK HLK-7628NLiu Yu2021-06-231-0/+1
| | | | | | | | | | | In the new kernel version 5.X,reboot will fail. When SOC is reset, flash has not exited the 4-byte address mode, which causes the operation mode mismatch of flash during boot.Add broken-flash-reset to make flash exit 4-byte address mode before SOC reset Signed-off-by: Liu Yu <f78fk@live.com>
* ramips: add missing "pinctrl-names" for Youku YK1Shiji Yang2021-06-231-0/+1
| | | | | | | | | Without this definition ethernet led can work as usual, but it's better to re-add it. Relying on default values may cause uncontrollable factors. Fixes: 882a6116d3d6 ("ramips: improve pinctrl for Youku YK-L1") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7620: move mt7620_mdio_mode() to ethernet driverMichael Pratt2021-06-233-25/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The function mt7620_mdio_mode is only called once and both the function and mdio_mode block have been named incorrectly, leading to confusion and useless commits. These lines in the mdio_mode block of mt7620_hw_init are only intended for boards with an external mt7530 switch. (see commit 194ca6127ee18cd3a95da4d03f02e43b5428c0bb) Therefore, move lines from mdio_mode to the place in soc_mt7620.c where the type of mt7530 switch is identified, and move lines from mt7620_mdio_mode to a main function. mt7620_mdio_mode was called from mt7620_gsw_init where the priv struct is available, so the lines must stay in mt7620_gsw_init function. In order to keep things as simple as possible, keep the DTS property related function calls together, by moving them from mt7620_gsw_probe to init. Remove the now useless DTS properties and extra phy nodes. Fixes: 5a6229a93df8 ("ramips: remove superfluous & confusing DT binding") Fixes: b85fe43ec8c4 ("ramips: mt7620: add force use of mdio-mode") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: use DTS to set PHY base address for external PHYsMichael Pratt2021-06-2323-1/+56
| | | | | | | | | | | | | | | | | | | | | | | Set the PHY base address to 12 for mt7530 and 8 for others, which is based on the default setting for some devices from printing the register with the following command after it is written to by uboot during the boot cycle. `md 0x10117014 1` PHY_BASE option only uses 5 bits of the register, bits 16 to 20, so use 8-bit integer type. Set the option using the DTS property mediatek,ephy-base and create the gsw node if missing. Also, added a kernel message to display the EPHY base address. Note: If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf) then there is adverse effects with Atheros switches. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: remove useless GMAC nodesMichael Pratt2021-06-233-26/+0
| | | | | | | | | | | | | | | | | | | These nodes are used for configuring a GMAC interface and for defining external PHYs to be accessed with MDIO. None of this is possible on MT7620N, only MT7620A, so remove them from all MT7620N DTS. When the mdio-bus node is missing, the driver returns -NODEV which causes the internal switch to not initialize. Replace that return so that everything works without the DTS node. Also, an extra kernel message to indicate for all error conditions that mdio-bus is disabled. Fixes: d482356322c9 ("ramips: mt7620n: add mdio node and disable port4 by default") Fixes: aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: simplify DTS properties for GMACMichael Pratt2021-06-2338-107/+17
| | | | | | | | | | | | | | | | | | | There are only 2 options in the driver for the function of mt7620 internal switch port 4: EPHY mode (RJ-45, internal PHY) GMAC mode (RGMII, external PHY) Let the DTS property be boolean instead of string where EPHY mode is the default. Fix how the properties are written for all DTS that use them, and add missing nodes where applicable, and remove useless nodes, and minor DTS formatting. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: reorganize DTSI files for D-Link DIR-8xxAdrian Schmutzler2021-06-208-27/+40
| | | | | | | | | | | * Remove micro-DTSI mt7621_dlink_dir-882-x1.dtsi to ease reading config without too much inheritance * Use "separate" partitioning DTSIs so we can use the partitioning without a complete match on the other settings (i.e. without the former parent DTSI) * Rename files to express the new organization Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link Archer C6 v3Amish Vishwakarma2021-06-133-180/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3) The patch adds identification changes to the existing TP-Link Archer A6, by Vinay Patil <post2vinay@gmail.com>, which has identical hardware. Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated by powercycling the router four times before the boot process is complete. Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com> [fix indent] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix LAN LED trigger assignment for Xiaomi Router 3 ProAdam Elyas2021-06-091-2/+2
| | | | | | | | | | | | The default trigger for the amber lights on lan1 and lan3 were mistakenly swapped after the device's migration to DSA. This caused activity on one port to trigger the amber light on the other port. Swapping their default trigger in the DTS file fixes that. Signed-off-by: Adam Elyas <adamelyas@outlook.com> [minor commit title adjustment, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix Ethernet random MAC address for HILINK HLK-7628NLiu Yu2021-06-091-0/+4
| | | | | | | | | | | | | | | | | | Set the ethernet address from flash. MAC addresses as verified by OEM firmware: use interface source 2g wlan0 factory 0x04 (label) LAN eth0.1 factory 0x28 (label+1) WAN eth0.2 factory 0x2e (label+2) Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N") Signed-off-by: Liu Yu <f78fk@live.com> [drop old MAC address setup from 02_network, cut out state_default changes, face-lift commit message, add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Add support for SERCOMM NA502Andreas Böhler2021-06-061-0/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for the Wavlink WL-WN579X3Ben Gainey2021-06-061-0/+210
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | About the device ---------------- SoC: MediaTek MT7620a @ 580MHz RAM: 64M FLASH: 8MB WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 2x (RTL8211F) BTN: - WPS - Reset - Router/Repeater/AP (3-way slide-switch) LED: - WPS (blue) - 3-segment Wifi signal representation (blue) - WiFi (blue) - WAN (blue) - LAN (blue) - Power (blue) UART: UART is present as Pads with through-holes on the PCB. They are located next to the reset button and are labelled Vcc/TX/RX/GND as appropriate. Use 3.3V, 57600-8N1. Installation ------------ Using the webcmd interface -------------------------- Warning: Do not update to the latest Wavlink firmware (version 20201201) as this removes the webcmd console and you will need to use the serial port instead. You will need to have built uboot/sqauashfs image for this device, and you will need to provide an HTTP service where the image can be downloaded from that is accessible by the device. You cannot use the device manufacturers firmware upgrade interface as it rejects the OpenWrt image. 1. Log into the device's admin portal. This is necessary to authenticate you as a user in order to be able to access the webcmd interface. 2. Navigate to http://<device-ip>/webcmd.shtml - you can access the console directly through this page, or you may wish to launch the installed `telnetd` and use telnet instead. * Using telnet is recommended since it provides a more convenient shell interface that the web form. * Launch telnetd from the form with the command `telnetd`. * Check the port that telnetd is running on using `netstat -antp|grep telnetd`, it is likely to be 2323. * Connect to the target using `telnet`. The username should be `admin2860`, and the password is your admin password. 3. On the target use `curl` to download the image. e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\ wavlink_wl-wn579x3-squashfs-sysupgrade.bin`. Check the hash using `md5sum`. 4. Use the mtd_write command to flash the image. * The flash partition should be mtd4, but check /sys/class/mtd/mtd4/name first. The partition should be called 'Kernel'. * To flash use the following command: `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>` Where mtd<n> is the Kernel partition, and <image-file> is the OpenWrt image previously downloaded. * The command above will erase, flash and then reboot the device. Once it reboots it will be running OpenWrt. Connect via ssh to the device at 192.168.1.1 on the LAN port. The WAN port will be configured via DHCP. Using the serial port --------------------- The device uses uboot like many other MT7260a based boards. To use this interface, you will need to connect to the serial interface, and provide a TFTP server. At boot follow the bootloader menu and select option 2 to erase/flash the image. Provide the address and filename details for the tftp server. The bootloader will do the rest. Once the image is flashed, the board will boot into OpenWrt. The console is available over the serial port. Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
* ramips: split Youku YK1 to YK-L1 and YK-L1cShiji Yang2021-06-053-5/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Model: Youku YK-L1/L1c * CPU: MT7620A * RAM: 128 MiB * Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c) * LAN: 2* 10M/100M Ports * WAN: 1* 10M/100M Port * USB: 1* USB2.0 * SD: 1* MicroSD socket * UART: 1* TTL, Baudrate 57600 Descriptions: Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look really different, the only hardware difference between the two models is flash size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can compatible with YK-L1's firmware but it's better to split it to different models. It is easy to identify the models by looking at the label on the bottom of the device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update" to install compatible firmware, so please backup config file before system upgrade. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [use more specific name for DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-053-0/+232
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
* ramips: add support for Linksys E5600Aashish Kulkarni2021-06-051-0/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Linksys EA7300 v1/ v2. Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: 128M DDR3-1600 * Flash: 128M NAND * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz) * Antennae: 2 internal fixed in the casing and 2 on the PCB * LEDs: Blue (x4 Ethernet) Blue+Orange (x2 Power + WPS and Internet) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This device has 2 partitions for the firmware called firmware and alt_firmware. To successfully flash and boot the device, the device should have been running from alt_firmware partition. To get the device booted through alt_firmware partition, download the OEM firmware from Linksys website and upgrade the firmware from web GUI. Once this is done, flash the OpenWrt Factory firmware from web GUI. Reverting to factory firmware: 1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of the following: Press the "wps" button as soon as power LED turns on when booting. (OR) Hard-reset the router consecutively three times to force it to boot from 'alt_firmware'. 2. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com> [fix hanging indents and wrap to 74 characters per line, add kmod-mt7663-firmware-sta package for 5GHz STA mode to work, remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk, set default-state "on" for power LED] Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com> [move check-size before append-metadata, remove trailing whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable additional UART on MikroTik RouterBOARD M33GPhilipp Borgers2021-06-051-0/+4
| | | | | | | The RouterBOARD M33G has an additional UART that should be enabled by default. Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
* ramips: add support for Wavlink WL-WN578A2Thomas Aldrian2021-05-281-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* ramips: add support for JCG Q20Chukun Pan2021-05-261-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-18 04:40:21 +0000