aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: replace pinctrl property namesChuanhong Guo2020-04-12256-719/+719
| | | | | | | | | | | | | | Upstream pinctrl driver in drivers/staging uses groups/function/ralink,num-gpios instead of ralink,group/ralink,function/ralink,nr-gpio Replace these properties in dts as well as the pinctrl driver in patches-4.14. This commit is created using: sed -i 's/ralink,group/groups/g' sed -i 's/ralink,function/function/g' sed -i 's/ralink,nr-gpio/ralink,num-gpios/g' Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7628: update dts for upstream gpio-mt7621 driverChuanhong Guo2020-04-1256-320/+278
| | | | | | | | | | upstream driver merged 3 separated gpio banks into one gpio node. and gpioX Y in our local driver should be replaced with gpio X*32+Y. This patch is created using the following sed command: sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge' Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: increase spi frequency for newifi d1/d2Chuanhong Guo2020-04-122-3/+2
| | | | | | | | increase spi frequency for both devices to 45MHz. while at it, also remove m25p,fast-read for newifi d1 as it's only needed when spi clock is higher than 50MHz. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: enable broken-flash-reset for some 32M flash boardsChuanhong Guo2020-04-127-0/+7
| | | | | | | These are boards known to start on 3-byte address mode, which requires broken-flash-reset if 4B_OPCODES isn't supported by the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: tidy up names for Ubiquiti devicesAdrian Schmutzler2020-04-125-25/+25
| | | | | | | | | | | | | | | The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in all targets except ramips and also recommended by the kernel. This patch adjusts the various board/image/device name variables accordingly. Since we touch it anyway, this also adds the space in "EdgeRouter X" as a hyphen to those variables to really make them consistent with the model name. While at it, create a real shared definition for the devices in image/mt7621.mk instead of deriving one device from another. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WN-AX2033GRYanase Yuki2020-04-121-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX2033GR is roughly the same as I-O DATA WN-AX1167GR2. The difference is Wi-Fi feature. Specification ============= - SoC: MediaTek MT7621A - RAM: DDR3 128 MiB - Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100) - Wi-Fi: MediaTek MT7603E - Wi-Fi: MediaTek MT7615 - Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN) - LED: 2x green LED - Input: 2x tactile switch, 1x slide switch - Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND) - Power: DC 12V This device only supports channel 1-13 and 36-140. Thus, narrower frequency limits compared to other devices are required for limiting wi-fi frequency correctly. Without this, non-supported frequencies are activated. Flash instructions ================== 1. Open the router management page (192.168.0.1). 2. Update router firmware using "initramfs-kernel.bin". 3. After updating, run sysupgrade with "sysupgrade.bin". Recovery instructions ===================== WN-AX2033GR contains Zyxel Z-LOADER 1. Setup TFTP server (IP address: 10.10.10.3). 2. Put official firmware into TFTP server directory (distribution site: https://www.iodata.jp/lib/software/w/2068.htm) 3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server. 4. Connect to serial console. 5. Interrupt booting by Esc key. 6. Flash firmware using "ATNR 1,[firmware filename]" command. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [adjust for kernel 5.4, add recovery instructions/frequency comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use full 8MB flash on ZyXEL KeeneticAlexey Dobrovolsky2020-04-081-1/+1
| | | | | | | | | | | | | | | | ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB. This commit fixes the problem. WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is an article with specs [2] (in Russian). [1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic [2] https://3dnews.ru/608774/page-2.html Fixes: FS#2487 Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
* ramips: add support for D-Link DWR-960Pawel Dembicki2020-04-081-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-960 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610 mpcie card) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Ethernet (1 LAN) (AR8035) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem - UART (J4) header on PCB (57600 8n1) - 9x LED, 2x button - JBOOT bootloader Known issues: - Flash is extremely slow. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: harmonize naming scheme for MikrotikAdrian Schmutzler2020-04-083-12/+12
| | | | | | | | | | | | | | | | | So far, image/device/board names for Mikrotik devices in mt7621 have been used quite inconsistently. This patch harmonizes the naming scheme by applying the same style as used lately in ath79, i.e. using "RouterBOARD" as separate word in the model name (instead of RB prefix for the number) and deriving the board/device name from that (= make lower case and replace spaces by hyphens). This style has already been used for most the model/DEVICE_MODEL variables in mt7621, so this is essentially just adjusting the remaining variables to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: reenable rbm11gTobias Schramm2020-04-081-1/+0
| | | | | | | I have a rbm11g and can confirm that the LAN port is indeed switch port 0. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
* ramips: add support for Buffalo WSR-2533DHPLINAGAKI Hiroshi2020-04-071-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N) - Ethernet : 10/100/1000 Mbps - Switch : MediaTek MT7530 (SoC) - LED/keys : 8x/6x (3x buttons, 2x slide-switches) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from triangle-mark - 57600n8 - Power : 12VDC 1.5A Flash instruction using initramfs image: 1. prepare the TFTP server with the initramfs image renamed to "linux.trx-recovery" and IP address "192.168.11.2" 2. press the "AOSS" button while powering on the WSR-2533DHPL 3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads the initramfs image and boot with it automatically 4. on the initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 5. wait ~120 seconds to complete flashing Switch position overview: - slide-switch1 (2x positions) - "AUTO" - "MANUAL" (not connected to gpio) - slide-switch2 (3x positions) - "ROUTER" - "AP" (not connected to gpio) - "WB" Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [add note on switches, fix group->groups for state_default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: harmonize Netgear R6120 DT LED node namesAlex Lewontin2020-04-061-3/+3
| | | | | | | | | This changes the node names for the LEDs in the Netgear R6120 device-tree file to provide consistency with other devices. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [improve commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add DTS triggers to USB LEDs for F9K1109v1Kip Porterfield2020-04-061-0/+18
| | | | | | | Alter DTS for Belkin F9K1109v1 to trigger USB leds from the echi/ochi ports. Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ramips: correct MTC WR1201 LAN ports namesRené van Dorst2020-04-041-4/+4
| | | | | | | LAN ports of MTC WR1201 are reversed, so correct their names Signed-off-by: René van Dorst <opensource@vdorst.com> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: add new NAND driverDENG Qingfang2020-04-041-2/+12
| | | | | | Add new NAND driver for MT7621 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: drop obsolete mx25l25635f dts hackDENG Qingfang2020-04-042-2/+2
| | | | | | 5.4 kernel has fixed this issue, so the hack is no longer needed. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix MikroTik 750Gr3 LAN ports namesDENG Qingfang2020-04-041-4/+4
| | | | | | They are labeled as LAN2..LAN5 instead of LAN1..LAN4 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFPDENG Qingfang2020-04-042-12/+7
| | | | | | | The original idea of bitbanged I2C is to use i2c-gpio-custom Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addressesDENG Qingfang2020-04-041-7/+14
| | | | | | | | | | | | | | | | | The name of each user port should be eth0..4, instead of lan1..4 and there is no WAN port. Rename them to match the official firmware. To avoid conflict with the master port (gmac0), rename it to "dsa". The official firmware assigns MAC address in this way: eth0 = label mac eth1 = label mac + 1 ... eth4 = label mac + 4 Since we have switched to DSA, it's possible to use different MAC for each port. Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621 remove unused pinctrl groups in dtsDENG Qingfang2020-04-0412-12/+12
| | | | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [split commit, remove leftover uart3->gpio setup] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: update dts/defconfig for DSADENG Qingfang2020-04-0468-103/+1820
| | | | | | | | | | | update dts and network/LED configuration for DSA driver. sysupgrade from images prior to this commit with config preserved will cause broken ethernet setup. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Acked-by: Jo-Philipp Wich <jo@mein.io> [split commit] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: update PCIe node in dtsiDENG Qingfang2020-04-041-14/+29
| | | | | | Update PCIe node in dtsi to match the new driver Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: update pinctrl nodesDENG Qingfang2020-04-0466-156/+156
| | | | | | Upstream GPIO driver uses "groups" "function" properties Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: convert GPIO dts refsDENG Qingfang2020-04-0470-374/+374
| | | | | | | The upstream driver does not use &gpio0..2 banks notation anymore, so convert them to &gpio Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: replace gpio/eth nodes in mt7621.dtsiDENG Qingfang2020-04-041-42/+94
| | | | | | | There's different gpio and ethernet drivers upstream for mt7621. Update these two nodes to match upstream dt bindings. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TOTOLINK A3Sungbo Eo2020-03-131-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Tested on device by JasonHCH <hsuan670629@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Ubiquiti UniFi nanoHDDavid Bauer2020-03-101-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621AT WiFi: MediaTek MT7603 bgn 2T2R MediaTek MT7615 ac 4T4R Flash: 32M SPI (Macronix MX25L25635F) RAM: 128M DDR3 (Winbond W631GG6KB) LED: Dome (Blue / White) BTN: Reset Installation ------------ These instructions were written for firmware version v3.9.27. Downgrade if necessary. 1. Copy the OpenWrt sysupgrade image to the devices /tmp folder via scp. On factory defaults, user and password is "ubnt" at 192.168.1.20/24. 2. Write the bootselect flag. Otherwise, the device might boot from the wrong partition. Verify the mtd partition used in the command below is the one labled "bs" in /proc/mtd (as this might change in the future). > dd if=/dev/zero bs=1 count=1 of=/dev/mtd4 3. Write the OpenWrt sysupgrade to the mtd partitions labled "kernel0" and "kernel1". > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6 > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7 4. Reboot or powercycle the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link RE210 v1Christoph Krapp2020-03-093-88/+191
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7620A RAM: 64MB FLASH: 8MB SPI WLAN: 2G: MediaTek MT7620A 5G: MediaTek MT7610EN ETH: 1x 10/100/1000M (Atheros AR8035) LED: RSSI (orange/green) WiFi 2G (green) WiFi 5G (green) Power (green) System (red / green) BTN: Power Reset LED WPS Serial ------ P1 - Tx P2 - Rx P3 - GND P4 - VCC Pin 4 is the one closest to the LAN port. MAC overview ------------ WAN *:4c uboot 0x1fc00 2.4 *:4c uboot 0x1fc00 5 *:4e uboot 0x1fc00 +2 Installation ------------ Web interface: It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial/TFTP: You can use initramfs for booting via RAM or flash the image directly. Additional Notes: If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. In order to flash back to stock, the first header and U-Boot needs to be stripped from the original firmware. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [change rssi LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: increase spi-max-frequency to 50 MHz for D-Link DIR-810LAdrian Schmutzler2020-03-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Read times drop when increasing frequency to 25 MHz and 50 MHz, but not in between or for further increase. So, use 50 MHz as the lowest frequency with the fastest speed. Test results (thanks to Roger): The device reports a mx25l6405d flash chip. I tried all the maximum values in the devices' datasheet (Table 10. AC CHARACTERISTICS). All of them worked with and without "m25p,fast-read": > 10 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 1m 33.00s user 0m 0.01s sys 1m 7.56s > 25 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.42s user 0m 0.02s sys 0m 23.58s > 25 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.45s user 0m 0.02s sys 0m 23.59s > 33 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.39s user 0m 0.00s sys 0m 23.60s > 33 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.46s user 0m 0.01s sys 0m 23.62s > 50 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.81s user 0m 0.01s sys 0m 18.25s > 50 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.84s user 0m 0.00s sys 0m 18.25s > 66 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.01s sys 0m 18.23s > 66 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.02s sys 0m 18.23s > 86 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.84s user 0m 0.01s sys 0m 18.24s > 86 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.02s sys 0m 18.23s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: fix and tidy up DTS for D-Link DIR-810LAdrian Schmutzler2020-03-051-8/+10
| | | | | | | | | | | | | This patch addresses several issues for D-Link DIR-810L: - add correct button codes - harmonize button node names - use generic flash@0 - remove unused pin groups from state_default - improve sorting of properties Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: fix partition offset for D-Link DIR-810LAdrian Schmutzler2020-03-051-2/+2
| | | | | | | | | | | | | | The Jffs2 partition for the D-Link DIR-810L is currently off by 0x10000. Apply the correct offset based on the other partitions' size/offset and the information about stock OS from the Wiki. This is just based on the named information and _not_ verified on device. Fixes: 36e3424fa520 ("ramips: add support for dir810l and asus rp-n53") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-041-0/+122
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-042-0/+249
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: move includes to DTSI for mt7628an_tplink_8m*Adrian Schmutzler2020-02-2213-33/+6
| | | | | | | | | | All devices inherited from mt7628an_tplink_8m.dtsi and mt7628an_tplink_8m-split-uboot.dtsi contain the same additional includes in the DTS files. Move them to the DTSI files instead. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move compatible for Ubiquiti Edgerouter X to DTS fileAdrian Schmutzler2020-02-222-2/+1
| | | | | | | | | | | | So far, the compatible for the Ubiquiti Edgerouter X has been defined in the DTSI file and inherited for the edgerouterx.dts, but overwritten for the edgerouterx-sfp.dts. In contrast, the model was stored in the DTS file in both cases. To resolve this somewhat confusing situation, move the compatible with the device name for edgerouterx to the DTS file as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant includes in DTS filesAdrian Schmutzler2020-02-227-15/+2
| | | | | | | | | | Many DTS files contain the same includes again that are already present in the DTSI files they are derived from. Remove those redundant includes in the DTS files. For vocore, the include is moved to the parent DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix HiWiFi HC5761A USB portDENG Qingfang2020-02-211-1/+12
| | | | | | Export GPIO 41 to power USB port Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix device name of netis WF-2881 to WF2881Sungbo Eo2020-02-071-4/+4
| | | | | | | | | | | The correct model name of WF-2881 is WF2881 without hyphen. The former used boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the sysupgrade-tar image, which is newly added in the previous commit, should not be used to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-071-1/+14
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-051-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-052-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: remove unnecessary execute permission bitSungbo Eo2020-02-041-0/+0
| | | | | | | | dts file does not need to be executable. 644 is enough. Fixes: f098c612b6db ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-012-0/+168
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use tpt DTS trigger for TP-Link TL-MR3020 v3 and TL-WA801ND v5Jan Alexander2020-01-302-0/+2
| | | | | | | | | | | | | | This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput LED trigger in order to react to all VAPs. It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the DTS and merges the now identical LAN LED configs. Verified these changes on a TL-MR3020v3. Signed-off-by: Jan Alexander <jan@nalx.net> [changed commit title and extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "ramips: fix NETGEAR R6260 EEPROM offset"David Bauer2020-01-304-26/+4
| | | | | | | | | | | | | This reverts commit 4716c843d62a5a4c37e7886f54bcf446aa26e786. Netgear seems to use different partition layouts on the R6260, which would require us to dynamically detect the position of (at least) the factory partition. Revert this fix to avoid breaking existing installations until a better solution has been worked out. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix NETGEAR R6260 EEPROM offsetDavid Bauer2020-01-294-4/+26
| | | | | | | | | | The EEPROM offset for the NETGEAR R6260 is incorrect, thus no valid calibration data is used. Fix this only for the NETGEAR R6260, as it's currently unknown whether or not other boards are affected. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for GL.iNet microuter-N300David Bauer2020-01-293-91/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a pocket-size travel router. It is essentially identical to the VIXMINI (internally referred as MT300N-v3) but with double the RAM and SPI-flash. Additionally, set the label-mac for both the VIXMINI as well as the microuter-N300. Hardware -------- SoC: MediaTek MT7628NN RAM: 128M DDR2 FLASH: 16M LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-181-0/+150
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
* ramips: rt305x: remove unnecessary mediatek,portmapSungbo Eo2020-01-182-2/+0
| | | | | | | | | "#mediatek,portmap" is not a valid property name. If mediatek,portmap equals 0x0, then the esw driver ditches it and uses the default value, 0x3f. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt76x8: fix bogus mediatek,portmapSungbo Eo2020-01-1818-14/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with string values. Convert the strings to integers to make it work. According to its switch setup, WRTnode 2P/2R have a WAN port at port 0, so the correct value should be 0x3e. tplink_8m.dtsi uses "llllw", but it does not match switch setups of any device using the DTSI. Remove it from the DTSI and add correct value to DTS for each device. These devices have a WAN port at port 0. Set the value to 0x3e. - tplink,archer-c20-v4 - tplink,archer-c50-v3 - tplink,tl-mr3420-v5 - tplink,tl-wr840n-v4 - tplink,tl-wr841n-v13 - tplink,tl-wr842n-v5 These devices have only one ethernet port. They don't need portmap setting. - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 Signed-off-by: Sungbo Eo <mans0n@gorani.run>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-24 14:51:18 +0000