aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* rampis: fix Reference to non-existent node for GB-PC2Arınç ÜNAL2022-12-311-2/+1
| | | | | | | | | | | | | | | Fix cannot build: Reference to non-existent node or label "macaddr_factory_e000" dtb compilation error. The cherry-pick had to be reworked to use the old mtd-mac-address way as openwrt-21.02 still wasn't migrated to nvmem implementation. Fixes: d604032c2a50 ("ramips: fix GB-PC1 and GB-PC2 device support") Fixes: #11654 Fixes: #11385 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> [ rework commit message, add more fixes tag ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: fix GB-PC1 and GB-PC2 LEDsArınç ÜNAL2022-11-272-14/+14
| | | | | | | | | | | | | | | | Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the device schematics. Tests on a GB-PC2 by me and Petr proved otherwise. Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired to GPIO 3 or 4 and the wiring is currently unknown. Set ethyellow-orange to display link state and activity of the ethyellow interface for GB-PC2. Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 2a6ef7f53d7b96e4ee0200196c28ed6b0a7c8465)
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-11-272-52/+60
| | | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 4807bd6a00bcf44dd821047db76a2a799f403cd4)
* rampis: feed zbt-we1026 external watchdogFederico Capoano2022-09-241-0/+8
| | | | | | | | | | | Without feeding the gpio watchdog, the board will reset after 90 seconds Signed-off-by: Arvid E. Picciani <aep@exys.org> (cherry picked from commit 1a97c03d864ee5ab917aff2988c62fce223c041e) [adapted to config-5.4] Signed-off-by: Federico Capoano <f.capoano@openwisp.io>
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-08-281-0/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea) [switch to mtd-mac-address instead of nvmem-cells]
* ramips: add support for Sitecom WLR-4100 v1 002Andrea Poletti2022-08-281-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router Specification: SoC: MT7620A RAM: 64 MB DDR2 Flash: MX25L6405D SPI NOR 8 MB WIFI: 2.4 GHz integrated Ethernet: 5x 10/100/1000 Mbps QCA8337 USB: 1x 2.0 LEDS: 2x GPIO controlled, 5x switch Buttons: 1x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB: VCC 3.3V GND TX RX baud: 115200, parity: none, flow control: none Installation Connect to one of LAN (yellow) ethernet ports, Open router configuration interface, Go to Toolbox > Firmware, Browse for OpenWrt factory image with dlf extension and hit Apply, Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues Some USB 2.0 devices work at full speed mode 1.1 only MAC addresses factory partition only contains one (binary) MAC address in 0x4. u-boot-env contains four (ascii) MAC addresses, of which two appear to be valid. factory 0x4 **:**:**:**:b9:84 binary u-boot-env ethaddr **:**:**:**:b9:84 ascii u-boot-env wanaddr **:**:**:**:b9:85 ascii u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii The factory firmware only assigns ethaddr. Thus, we take the binary value which we can use directly in DTS. Additional information OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), based on RT3352 SoC The nvmem feature (commit 06bb4a5) was introduced in master after the splitting of the 21.02 branch. It need to be reverted in 21.02.. Signed-off-by: Andrea Poletti <polex73@yahoo.it> [remove config DT label, convert to nvmem, remove MAC address setup from u-boot-env, add MAC address info to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit de0c380a5f8289839ab970e794a45f0e04a466a3) Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 535b0c70b1c466733b009144f81f5207f1ecd311)
* ramips: zbt-wg2626: Add the reset gpio for PCIe port 1Alban Bedel2022-05-011-0/+3
| | | | | | | | | | | | | | The 2.4GHz interface doesn't come up properly with the log showing: mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) As seen on other MT7621 boards this is caused by a missing reset GPIO. The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO list to also reset the 2.4GHz interface on port 1. Signed-off-by: Alban Bedel <albeu@free.fr> (cherry picked from commit f953a1a4bfba2fa70c12bb80938aa66481a673b6)
* ramips: mt7620: move mt7620_mdio_mode() to ethernet driverMichael Pratt2022-04-193-25/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The function mt7620_mdio_mode is only called once and both the function and mdio_mode block have been named incorrectly, leading to confusion and useless commits. These lines in the mdio_mode block of mt7620_hw_init are only intended for boards with an external mt7530 switch. (see commit 194ca6127ee18cd3a95da4d03f02e43b5428c0bb) Therefore, move lines from mdio_mode to the place in soc_mt7620.c where the type of mt7530 switch is identified, and move lines from mt7620_mdio_mode to a main function. mt7620_mdio_mode was called from mt7620_gsw_init where the priv struct is available, so the lines must stay in mt7620_gsw_init function. In order to keep things as simple as possible, keep the DTS property related function calls together, by moving them from mt7620_gsw_probe to init. Remove the now useless DTS properties and extra phy nodes. Fixes: 5a6229a93df8 ("ramips: remove superfluous & confusing DT binding") Fixes: b85fe43ec8c4 ("ramips: mt7620: add force use of mdio-mode") Signed-off-by: Michael Pratt <mcpratt@pm.me> (cherry picked from commit 6972e498d33ec896c676b7af91e3bfb00aa846a1)
* ramips: mt7620: use DTS to set PHY base address for external PHYsMichael Pratt2022-04-1923-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | Set the PHY base address to 12 for mt7530 and 8 for others, which is based on the default setting for some devices from printing the register with the following command after it is written to by uboot during the boot cycle. `md 0x10117014 1` PHY_BASE option only uses 5 bits of the register, bits 16 to 20, so use 8-bit integer type. Set the option using the DTS property mediatek,ephy-base and create the gsw node if missing. Also, added a kernel message to display the EPHY base address. Note: If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf) then there is adverse effects with Atheros switches. Signed-off-by: Michael Pratt <mcpratt@pm.me> (cherry picked from commit 0976b6c4262a11a8d0dab9aeb64f5cdee266c44a)
* ramips: mt7620: remove useless GMAC nodesMichael Pratt2022-04-193-26/+0
| | | | | | | | | | | | | | | | | | | | These nodes are used for configuring a GMAC interface and for defining external PHYs to be accessed with MDIO. None of this is possible on MT7620N, only MT7620A, so remove them from all MT7620N DTS. When the mdio-bus node is missing, the driver returns -NODEV which causes the internal switch to not initialize. Replace that return so that everything works without the DTS node. Also, an extra kernel message to indicate for all error conditions that mdio-bus is disabled. Fixes: d482356322c9 ("ramips: mt7620n: add mdio node and disable port4 by default") Fixes: aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default") Signed-off-by: Michael Pratt <mcpratt@pm.me> (cherry picked from commit a2acdf9607045e5669c305c57dd7c77be8351ba0)
* ramips: mt7620: simplify DTS properties for GMACMichael Pratt2022-04-1938-107/+17
| | | | | | | | | | | | | | | | | | | | There are only 2 options in the driver for the function of mt7620 internal switch port 4: EPHY mode (RJ-45, internal PHY) GMAC mode (RGMII, external PHY) Let the DTS property be boolean instead of string where EPHY mode is the default. Fix how the properties are written for all DTS that use them, and add missing nodes where applicable, and remove useless nodes, and minor DTS formatting. Signed-off-by: Michael Pratt <mcpratt@pm.me> (cherry picked from commit 953bfe2eb3b7236a72fa41ab2204fdaa9fd09f65)
* ramips: add support for the Wavlink WL-WN579X3Ben Gainey2022-04-191-0/+210
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | About the device ---------------- SoC: MediaTek MT7620a @ 580MHz RAM: 64M FLASH: 8MB WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 2x (RTL8211F) BTN: - WPS - Reset - Router/Repeater/AP (3-way slide-switch) LED: - WPS (blue) - 3-segment Wifi signal representation (blue) - WiFi (blue) - WAN (blue) - LAN (blue) - Power (blue) UART: UART is present as Pads with through-holes on the PCB. They are located next to the reset button and are labelled Vcc/TX/RX/GND as appropriate. Use 3.3V, 57600-8N1. Installation ------------ Using the webcmd interface -------------------------- Warning: Do not update to the latest Wavlink firmware (version 20201201) as this removes the webcmd console and you will need to use the serial port instead. You will need to have built uboot/sqauashfs image for this device, and you will need to provide an HTTP service where the image can be downloaded from that is accessible by the device. You cannot use the device manufacturers firmware upgrade interface as it rejects the OpenWrt image. 1. Log into the device's admin portal. This is necessary to authenticate you as a user in order to be able to access the webcmd interface. 2. Navigate to http://<device-ip>/webcmd.shtml - you can access the console directly through this page, or you may wish to launch the installed `telnetd` and use telnet instead. * Using telnet is recommended since it provides a more convenient shell interface that the web form. * Launch telnetd from the form with the command `telnetd`. * Check the port that telnetd is running on using `netstat -antp|grep telnetd`, it is likely to be 2323. * Connect to the target using `telnet`. The username should be `admin2860`, and the password is your admin password. 3. On the target use `curl` to download the image. e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\ wavlink_wl-wn579x3-squashfs-sysupgrade.bin`. Check the hash using `md5sum`. 4. Use the mtd_write command to flash the image. * The flash partition should be mtd4, but check /sys/class/mtd/mtd4/name first. The partition should be called 'Kernel'. * To flash use the following command: `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>` Where mtd<n> is the Kernel partition, and <image-file> is the OpenWrt image previously downloaded. * The command above will erase, flash and then reboot the device. Once it reboots it will be running OpenWrt. Connect via ssh to the device at 192.168.1.1 on the LAN port. The WAN port will be configured via DHCP. Using the serial port --------------------- The device uses uboot like many other MT7260a based boards. To use this interface, you will need to connect to the serial interface, and provide a TFTP server. At boot follow the bootloader menu and select option 2 to erase/flash the image. Provide the address and filename details for the tftp server. The bootloader will do the rest. Once the image is flashed, the board will boot into OpenWrt. The console is available over the serial port. Signed-off-by: Ben Gainey <ba.gainey@googlemail.com> (cherry picked from commit a509b80065b6680e3e007203084c147f77b6717f)
* ramips: split Youku YK1 to YK-L1 and YK-L1cShiji Yang2022-04-193-5/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Model: Youku YK-L1/L1c * CPU: MT7620A * RAM: 128 MiB * Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c) * LAN: 2* 10M/100M Ports * WAN: 1* 10M/100M Port * USB: 1* USB2.0 * SD: 1* MicroSD socket * UART: 1* TTL, Baudrate 57600 Descriptions: Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look really different, the only hardware difference between the two models is flash size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can compatible with YK-L1's firmware but it's better to split it to different models. It is easy to identify the models by looking at the label on the bottom of the device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update" to install compatible firmware, so please backup config file before system upgrade. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [use more specific name for DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 4a9f389ed2dcee18a5c5e1f0d4e5c406f9290579)
* ramips: improve pinctrl for Youku YK-L1Shiji Yang2022-04-191-12/+4
| | | | | | | | 1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it. 2. led "wan" can be triggered by ethernet pinctrl by default so just drop it. Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 882a6116d3d6394dd109350287067accebbf6114)
* ramips: speed up spi frequency for Youku YK-L1Shiji Yang2022-04-191-1/+1
| | | | | | | | | | | | Youku YK-L1 has a huge storage space up to 32 MB. It is better to use a higher spi clock to read or write serial nor flash chips. Youku YK-L1 has Winbond w25q256fvfg on board that can support 104 MHz spi clock so 48 MHz is safe enough. The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz defined in dts file will set only 48 MHz in spi bus. Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit bf7ddb18f1bfa0b61b4dc43732c114f20900bd4b)
* ramips: remove obsolete mx25l25635f compatible hackDENG Qingfang2022-04-194-4/+4
| | | | | | | | The kernel bump to 5.4 has removed the mx25l25635f hack, and the mx25l25635f compatible is no longer required. Signed-off-by: DENG Qingfang <dqfext@gmail.com> (cherry picked from commit 06af45ec0502d5cb0529ac46fcb34c4c63394723)
* ramips: fix reboot for remaining 32 MB boardsMichael Pratt2022-04-0818-4/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following devices have a Winbond W25Q256FV flash chip, which does not have the RESET pin enabled by default, and otherwise would require setting a bit in a status register. Before moving to Linux 5.4, we had the patch: 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch which kept specific flash chips with explicit 3-byte and 4-byte address modes to stay in 3-byte address mode while idle (after an erase or write) by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch. this was obsoleted by the patch: 481-mtd-spi-nor-rework-broken-flash-reset-support.patch which uses the newer upstream flag SNOR_F_BROKEN_RESET for devices with a flash chip that cannot be hardware reset with RESET pin and therefore must be left in 3-byte address mode when idle. The new patch requires that the DTS of affected devices have the property "broken-flash-reset", which was not yet added for most of them. This commit adds the property for remaining affected devices in ramips target, specifically because of the flash chip model. However, it is possible that there are other devices where the flash chip uses an explicit 4-byte address mode and the RESET pin is not connected to the SOC on the board, and those DTS would also need this property. Ref: 22d982ea0033 ("ramips: add support for switching between 3-byte and 4-byte addressing") Ref: dfa521f12953 ("generic: spi-nor: rework broken-flash-reset") Signed-off-by: Michael Pratt <mcpratt@pm.me> [pepe2k@gmail.com: backported to 21.02] Fixes: #9655, #9636, #9547 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit 74516f4357d281f093f0daac01c4c5c239acc443)
* Revert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"Sungbo Eo2022-02-271-1/+1
| | | | | | | | | | | | | | | | | | | | | This reverts commit 13a185bf8acb67da4a68873e560876c0e60b1a87. There was a report that one A1004ns device fails to detect its flash chip correctly: [ 1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08 [ 1.484110] spi-nor: probe of spi0.0 failed with error -2 It also uses a different flash chip model: * in my hand: Winbond W25Q128FVSIG (SOIC-8) * reported: Macronix MX25L12845EMI-10G (SOP-16) Reducing spi-max-frequency solved the detection failure. Hence revert. Reported-by: Koasing <koasing@gmail.com> Tested-by: Koasing <koasing@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit 9968a909c248169064446ed40e66d18986d93d11)
* ramips: minew g1-c: Allow dynamic RAM sizesBruno Randolf2021-11-011-5/+0
| | | | | | | | Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB versions of Minew G1-C. This is also in line with the behaviour of most other RAMIPS boards. Signed-off-by: Bruno Randolf <br1@einfach.org>
* ramips: add support for minew g1-cAlexander Couzens2021-09-211-0/+142
| | | | | | | | | | | | | | | | | | | | | | The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: fix LAN LED trigger assignment for Xiaomi Router 3 ProAdam Elyas2021-06-121-2/+2
| | | | | | | | | | | | | The default trigger for the amber lights on lan1 and lan3 were mistakenly swapped after the device's migration to DSA. This caused activity on one port to trigger the amber light on the other port. Swapping their default trigger in the DTS file fixes that. Signed-off-by: Adam Elyas <adamelyas@outlook.com> [minor commit title adjustment, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit edaf432bf411767f3e8a9e5effc3a416bcac46c7)
* ramips: fix Ethernet random MAC address for HILINK HLK-7628NLiu Yu2021-06-121-0/+4
| | | | | | | | | | | | | | | | | | | Set the ethernet address from flash. MAC addresses as verified by OEM firmware: use interface source 2g wlan0 factory 0x04 (label) LAN eth0.1 factory 0x28 (label+1) WAN eth0.2 factory 0x2e (label+2) Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N") Signed-off-by: Liu Yu <f78fk@live.com> [drop old MAC address setup from 02_network, cut out state_default changes, face-lift commit message, add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit ae9c5cd37bf5c08452f314b54afa963a00bdde30)
* ramips: Add support for SERCOMM NA502Andreas Böhler2021-06-101-0/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit a3d8c1295ed9eeceabd78ab86e73b151ae2868a9)
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-101-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b232680f847f4ea8d058849a51dedebb8e398a01)
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-103-0/+232
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com> (cherry picked from commit 6d23e474ad9d0eba935696c66db4fb6e2037bb72)
* ramips: add support for Linksys E5600Aashish Kulkarni2021-06-101-0/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Linksys EA7300 v1/ v2. Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: 128M DDR3-1600 * Flash: 128M NAND * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz) * Antennae: 2 internal fixed in the casing and 2 on the PCB * LEDs: Blue (x4 Ethernet) Blue+Orange (x2 Power + WPS and Internet) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This device has 2 partitions for the firmware called firmware and alt_firmware. To successfully flash and boot the device, the device should have been running from alt_firmware partition. To get the device booted through alt_firmware partition, download the OEM firmware from Linksys website and upgrade the firmware from web GUI. Once this is done, flash the OpenWrt Factory firmware from web GUI. Reverting to factory firmware: 1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of the following: Press the "wps" button as soon as power LED turns on when booting. (OR) Hard-reset the router consecutively three times to force it to boot from 'alt_firmware'. 2. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com> [fix hanging indents and wrap to 74 characters per line, add kmod-mt7663-firmware-sta package for 5GHz STA mode to work, remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk, set default-state "on" for power LED] Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com> [move check-size before append-metadata, remove trailing whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Sannihith Kinnera <digislayer@protonmail.com> (cherry picked from commit 251c995cbb1ea5ad1de14775312c2bd19ed10439)
* ramips: add support for JCG Q20Chukun Pan2021-06-101-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit 57cb387cfeee2a07902a2f1383ca471ef47265f3)
* ramips: add support for cudy WR2100Leon M. George2021-06-101-0/+201
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications SoC: MT7621 CPU: 880 MHz Flash: 16 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac MT7603E / MT7615E Ethernet: 5x Gbit ports Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. R4 & R5 need to be shorted (0-100Ω) for the UART to work. Signed-off-by: Leon M. George <leon@georgemail.eu> [remove non-required switch-port node - remove trgmii phy-mode] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 3501db9b9b4a71ae52c539b46af817783c327866)
* ramips: add support for TP-Link Archer C6U v1 (EU)Georgi Vlaev2021-06-101-0/+213
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6U v1 (EU). The device is also known in some market as Archer C6 v3. This patch supports only Archer C6U v1 (EU). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (Winbond 25Q128) * WiFi 5GHz: Mediatek MT7613BEN (2x2:2) * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) * Ethernet: MT7630, 5x 1000Base-T. * LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB * Buttons: Reset, WPS. * UART: Serial console (115200 8n1), J1(GND:3) * USB: One USB2 port. Installation: ------------ Install the OpenWrt factory image for C6U is from the TP-Link web interface. 1) Go to "Advanced/System Tools/Firmware Update". 2) Click "Browse" and upload the OpenWrt factory image: openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. 3) Click the "Upgrade" button, and select "Yes" when prompted. Recovery to stock firmware: -------------------------- The C6U bootloader has a failsafe mode that provides a web interface (running at 192.168.0.1) for reverting back to the stock TP-Link firmware. The failsafe interface is triggered from the serial console or on failed kernel boot. Unfortunately, there's no key combination that enables the failsafe mode. This gives us two options for recovery: 1) Recover using the serial console (J1 header). The recovery interface can be selected by hitting 'x' when prompted on boot. 2) Trigger the bootloader failsafe mode. A more dangerous option is force the bootloader into recovery mode by erasing the OpenWrt partition from the OpenWrt's shell - e.g "mtd erase firmware". Please be careful, since erasing the wrong partition can brick your device. MAC addresses: ------------- OEM firmware configuration: D8:07:B6:xx:xx:83 : 5G D8:07:B6:xx:xx:84 : LAN (label) D8:07:B6:xx:xx:84 : 2.4G D8:07:B6:xx:xx:85 : WAN Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com> (cherry picked from commit a46ad596a3e076599f38a4132b5d6dfee8a3102a)
* ramips: add support for TP-Link Archer A6 v3Vinay Patil2021-06-101-0/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer A6 v3 The router is sold in US and India with FCC ID TE7A6V3 Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated from serial console only. Press 'x' while u-boot is starting Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Thanks to: Frankis for Randmon MAC address fix. Signed-off-by: Vinay Patil <post2vinay@gmail.com> [remove superfluous factory image definition, whitespacing] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f8f8935adb2be1ebce46a8d7058c76a8d3a9bd89)
* ramips: mt7621: Add support for ZyXEL NR7101Bjørn Mork2021-06-101-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE with integrated directional 5G/LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E - Switch: 1 LAN port (Gigabiti) - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC - SIM: 2 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/yellow under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to 5G/LTE bridge or router. The Wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover, the WLAN button and 12 screws holding the back plate and antenna cover together. The GPS antenna is fixed to the cover, so be careful with the cable. Remove 4 screws fixing the antenna board to the main board, again being careful with the cables. A bluetooth TTL adapter is recommended for permanent console access, to keep the router water and dustproof. The 3.3V pin is able to power such an adapter. MAC addresses: OpenWrt OEM Address Found as lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex) wwan0 usb0 random WARNING!! ISP managed firmware might at any time update itself to a version where all known workarounds have been disabled. Never boot an ISP managed firmware with a SIM in any of the slots if you intend to use the router with OpenWrt. The bootloader lock can only be disabled with root access to running firmware. The flash chip is physically inaccessible without soldering. Installation from OEM web GUI: - Log in as "supervisor" on https://172.17.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Installation from OEM ssh: - Log in as "root" on 172.17.1.1 port 22022 - scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp - Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit - Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Copying OpenWrt to the recovery partition: - Verify that you are running a working OpenWrt recovery image from flash - ssh to root@192.168.1.1 and run: fw_setenv CheckBypass 0 mtd -r erase Kernel2 - Wait while the bootloader mirrors Image1 to Image2 NOTE: This should only be done after successfully booting the OpenWrt recovery image from the primary partition during installation. Do not do this after having sysupgraded OpenWrt! Reinstalling the recovery image on normal upgrades is not required or recommended. Installation from Z-Loader: - Halt boot by pressing Escape on console - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image NOTE: ATNR will write the recovery image to both primary and recovery partitions in one go. Booting from RAM: - Halt boot by pressing Escape on console - Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu - Press "4" to select "4: Entr boot command line interface." - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Load it using "tftpboot 0x88000000 initramfs-recovery.bin" - Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL header This method can also be used to RAM boot OEM firmware. The warning regarding OEM applies! Never boot an unknown OEM firmware, or any OEM firmware with a SIM in any slot. NOTE: U-Boot configuration is incomplete (on some devices?). You may have to configure a working mac address before running tftp using "setenv eth0addr <mac>" Unlocking the bootloader: If you are unebale to halt boot, then the bootloader is locked. The OEM firmware locks the bootloader on every boot by setting DebugFlag to 0. Setting it to 1 is therefore only temporary when OEM firmware is installed. - Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware - Run "fw_setenv DebugFlag 0x1" in OpenWrt NOTE: OpenWrt does this automatically on first boot if necessary NOTE2: Setting the flag to 0x1 avoids the reset to 0 in known OEM versions, but this might change. WARNING: Writing anything to flash while the bootloader is locked is considered extremely risky. Errors might cause a permanent brick! Enabling management access from LAN: Temporary workaround to allow installing OpenWrt if OEM firmware has disabled LAN management: - Connect to console - Log in as "root" - Run "iptables -I INPUT -i br0 -j ACCEPT" Notes on the OEM/bootloader dual partition scheme The dual partition scheme on this device uses Image2 as a recovery image only. The device will always boot from Image1, but the bootloader might copy Image2 to Image1 under specific conditions. This scheme prevents repurposing of the space occupied by Image2 in any useful way. Validation of primary and recovery images is controlled by the variables CheckBypass, Image1Stable, and Image1Try. The bootloader sets CheckBypass to 0 and reboots if Image1 fails validation. If CheckBypass is 0 and Image1 is invalid then Image2 is copied to Image1. If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to Image2. If CheckBypass is 1 then all tests are skipped and Image1 is booted unconditionally. CheckBypass is set to 1 after each successful validation of Image1. Image1Try is incremented if Image1Stable is 0, and Image2 is copied to Image1 if Image1Try is 3 or larger. But the bootloader only tests Image1Try if CheckBypass is 0, which is impossible unless the booted image sets it to 0 before failing. The system is therefore not resilient against runtime errors like failure to mount the rootfs, unless the kernel image sets CheckBypass to 0 before failing. This is not yet implemented in OpenWrt. Setting Image1Stable to 1 prevents the bootloader from updating Image1Try on every boot, saving unnecessary writes to the environment partition. Keeping an OpenWrt initramfs recovery as Image2 is recommended primarily to avoid unwanted OEM firmware boots on failure. Ref the warning above. It enables console-less recovery in case of some failures to boot from Image1. Signed-off-by: Bjørn Mork <bjorn@mork.no> Tested-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 2449a632084b29632605e5a79ce5d73028eb15dd)
* ramips: add support for ZTE MF283+Lech Perczak2021-06-021-0/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem. Hardware highlighs: - CPU: MIPS24KEc at 400MHz, - RAM: 64MB DDR2, - Flash: 16MB SPI, - Ethernet: 4 10/100M port switch with VLAN support, - Wireless: Dual-stream 802.11n (RT2860), with two internal antennas, - WWAN: Built-in ZTE P685M modem, with two internal antennas and two switching SMA connectors for external antennas, - FXS: Single ATA, with two connectors marked PHONE1 and PHONE2, internally wired in parallel by 0-Ohm resistors, handled entirely by internal WWAN modem. - USB: internal miniPCIe slot for modem, unpopulated USB A connector on PCB. - SIM slot for the WWAN modem. - UART connector for the console (unpopulated) at 3.3V, pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND, settings: 57600-8-N-1. - LEDs: Power (fixed), WLAN, WWAN (RGB), phone (bicolor, controlled by modem), Signal, 4 link/act LEDs for LAN1-4. - Buttons: WPS, reset. Installation: As the modem is, for most of the time, provided by carriers, there is no possibility to flash through web interface, only built-in FOTA update and TFTP recovery are supported. There are two installation methods: (1) Using serial console and initramfs-kernel - recommended, as it allows you to back up original firmware, or (2) Using TFTP recovery - does not require disassembly. (1) Using serial console: To install OpenWrt, one needs to disassemble the router and flash it via TFTP by using serial console: - Locate unpopulated 4-pin header on the top of the board, near buttons. - Connect UART adapter to the connector. Use 3.3V voltage level only, omit VCC connection. Pin 1 (VCC) is marked by square pad. - Put your initramfs-kernel image in TFTP server directory. - Power-up the device. - Press "1" to load initramfs image to RAM. - Enter IP address chosen for the device (defaults to 192.168.0.1). - Enter TFTP server IP address (defaults to 192.168.0.22). - Enter image filename as put inside TFTP server - something short, like firmware.bin is recommended. - Hit enter to load the image. U-boot will store above values in persistent environment for next installation. - If you ever might want to return to vendor firmware, BACK UP CONTENTS OF YOUR FLASH NOW. For this router, commonly used by mobile networks, plain vendor images are not officially available. To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the most important, and copy them over network to your PC. But in case anything goes wrong, PLEASE do back up ALL OF THEM. - From under OpenWrt just booted, load the sysupgrade image to tmpfs, and execute sysupgrade. (2) Using TFTP recovery - Set your host IP to 192.168.0.22 - for example using: sudo ip addr add 192.168.0.22/24 dev <interface> - Set up a TFTP server on your machine - Put the sysupgrade image in TFTP server root named as 'root_uImage' (no quotes), for example using tftpd: cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage - Power on the router holding BOTH Reset and WPS buttons held for around 5 seconds, until after WWAN and Signal LEDs blink. - Wait for OpenWrt to start booting up, this should take around a minute. Return to original firmware: Here, again there are two possibilities are possible, just like for installation: (1) Using initramfs-kernel image and serial console (2) Using TFTP recovery (1) Using initramfs-kernel image and serial console - Boot OpenWrt initramfs-kernel image via TFTP the same as for installation. - Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/ - Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is your backup taken before OpenWrt installation, and /dev/mtd3 is the "firmware" partition. (2) Using TFTP recovery - Follow the same steps as for installation, but replacing 'root_uImage' with firmware backup you took during installation, or by vendor firmware obtained elsewhere. A few quirks of the device, noted from my instance: - Wired and wireless MAC addresses written in flash are the same, despite being in separate locations. - Power LED is hardwired to 3.3V, so there is no status LED per se, and WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED for status - original firmware also does this in bootup. - FXS subsystem and its LED is controlled by the modem, so it work independently of OpenWrt. Tested to work even before OpenWrt booted. I managed to open up modem's shell via ADB, and found from its kernel logs, that FXS and its LED is indeed controlled by modem. - While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for each and every one of them manually, so this might not be complete - it looks like bicolor LED is used for FXS, possibly to support dual-ported variant in other device sharing the PCB. - Flash performance is very low, despite enabling 50MHz clock and fast read command, due to using 4k sectors throughout the target. I decided to keep it at the moment, to avoid breaking existing devices - I identified one potentially affected, should this be limited to under 4MB of Flash. The difference between sysupgrade durations is whopping 3min vs 8min, so this is worth pursuing. In vendor firmware, WWAN LED behaviour is as follows, citing the manual: - red - no registration, - green - 3G, - blue - 4G. Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan looks reasonable at the moment, for full replacement, a script similar to "rssileds" would need to be developed. Behaviour of "Signal LED" in vendor firmware is as follows: - Off - no signal, - Blinking - poor coverage - Solid - good coverage. A few more details on the built-in LTE modem: Modem is not fully supported upstream in Linux - only two CDC ports (DIAG and one for QMI) probe. I sent patches upstream to add required device IDs for full support. The mapping of USB functions is as follows: - CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools. - CDC (PCUI) - not supported by upstream 'option' driver yet. Patch submitted upstream. - CDC (Modem) - Exactly the same as above - QMI - A patch is sent upstream to add device ID, with that in place, uqmi did connect successfully, once I selected correct PDP context type for my SIM (IPv4-only, not default IPv4v6). - ADB - self-explanatory, one can access the ADB shell with a device ID added to 51-android.rules like so: SUBSYSTEM!="usb", GOTO="android_usb_rules_end" LABEL="android_usb_rules_begin" SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes" ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess" LABEL="android_usb_rules_end" While not really needed in OpenWrt, it might come useful if one decides to move the modem to their PC to hack it further, insides seem to be pretty interesting. ADB also works well from within OpenWrt without that. O course it isn't needed for normal operation, so I left it out of DEVICE_PACKAGES. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [remove kmod-usb-ledtrig-usbport, take merged upstream patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 59d065c9f81c4d1a89464d071134a50529449f34) [Manually remove no longer needed patches for modem] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: fix mac addresses of Youku YK1Shiji Yang2021-05-141-1/+2
| | | | | | | | | | | | | | | MAC addresses read from official firmware value location Wlan xx 71 de factory@0x04 Lan xx 71 dd factory@0x28 Wan xx 71 df factory@0x2e Label xx 71 dd factory@0x28 Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix sorting in 02_network, redact commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit e57e460dc75836d3227e7370b9e64a0eabc9d91d)
* ramips: reduce spi-max-frequency for Xiaomi MI Router 4AGDavid Bentham2021-04-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Reduce spi-max-frequency for Xiaomi MI Router 4AG model Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV. These flash chips are capable of high frequency, but due to poor board design or manufacture process. We are seeing the following errors in the linux kernel bootup: `spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c spi-nor: probe of spi0.0 failed with error -2` This causes the partitions not to be detected `VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6` Then creates a bootloop and a bricked router. The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz. Signed-off-by: David Bentham <db260179@gmail.com> (cherry picked from commit 17e690017d76c49070bc99d6a376b1926259c5ff)
* ramips: add support for ELECOM WRC-1750GST2INAGAKI Hiroshi2021-03-221-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB (NT5CC128M16JR-EK) - Flash : SPI-NOR 32 MiB (MX25L25645GMI-08G) - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX, from ethernet port side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-1750GST2 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC addresses: LAN : 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex)) WAN : 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex)) 2.4GHz : 04:AB:18:xx:xx:25 (Factory, 0x4 (hex)) 5GHz : 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit b3ca1f30efd7bb96a22f72b766d302e552265276)
* ramips: overwrite reset gpio properties in DIR-860L DTSStijn Segers2021-02-241-0/+3
| | | | | | | | | | | | | | | As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1) on PCI-E port 1 comes up reliably. Fixes the following error that popped up in dmesg: [ 1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Stijn Segers <foss@volatilesystems.org> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> (cherry picked from commit 06356f00200639c48d95330e633965957b0347ab)
* ramips: overwrite reset gpio properties in EX6150 DTSStijn Segers2021-02-201-0/+3
| | | | | | | | | | | | | | | | The Netgear EX6150 can, just like the D-Link DIR-860L rev B1, fail to initialise both radios in some cases. Add the reset GPIOs explicitly so the PCI-E devices get re-initialised properly. See also FS #3632. Error shows up in dmesg as follows: [ 1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) Tested-by: Kurt Roeckx <kurt@roeckx.be> Signed-off-by: Stijn Segers <foss@volatilesystems.org> [removed period from commit title] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit af1b6799c6ec9af7a30d63a5ddfed20f443b991c)
* ramips: mt7621: add TP-Link EAP235-Wall supportSander Vanheule2021-02-191-0/+180
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access point with four gigabit ethernet ports. When connecting to the device's serial port, it is strongly advised to use an isolated UART adapter. This prevents linking different power domains created by the PoE power supply, which may damage your devices. The device's U-Boot supports saving modified environments with `saveenv`. However, there is no u-boot-env partition, and saving modifications will cause the partition table to be overwritten. This is not an issue for running OpenWrt, but will prevent the vendor FW from functioning properly. Device specifications: * SoC: MT7621DAT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (MT7603EN): b/g/n, 2x2 * Wireless 5GHz (MT7613BEN): a/n/ac, 2x2 * Ethernet: 4× GbE * Back side: ETH0, PoE PD port * Bottom side: ETH1, ETH2, ETH3 * Single white device LED * LED button, reset button (available for failsafe) * PoE pass-through on port ETH3 (enabled with GPIO) Datasheet of the flash chip specifies a maximum frequency of 33MHz, but that didn't work. 20MHz gives no errors with reading (flash dump) or writing (sysupgrade). Device mac addresses: Stock firmware uses the same MAC address for ethernet (on device label) and 2.4GHz wireless. The 5GHz wireless address is incremented by one. This address is stored in the 'info' ('default-mac') partition at an offset of 8 bytes. From OEM ifconfig: eth a4:2b:b0:...:88 ra0 a4:2b:b0:...:88 rai0 a4:2b:b0:...:89 Flashing instructions: * Enable SSH in the web interface, and SSH into the target device * run `cliclientd stopcs`, this should return "success" * upload the factory image via the web interface Debricking: U-boot can be interrupted during boot, serial console is 57600 baud, 8n1 This allows installing a sysupgrade image, or fixing the device in another way. * Access serial header from the side of the board, close to ETH3, pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3. * Interrupt bootloader by holding '4' during boot, which drops the bootloader into its shell * Change default 'serverip' and 'ipaddr' variables (optional) * Download initramfs with `tftpboot`, and boot image with `bootm` # tftpboot 84000000 openwrt-initramfs.bin # bootm Revert to stock: Using the tplink-safeloader utility from the firmware-utils package, TP-Link's firmware image can be converted to an OpenWrt-compatible sysupgrade image: $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \ -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin This can then be flashed using the OpenWrt sysupgrade interface. The image will appear to be incompatible and must be force flashed, without keeping the current configuration. Known issues: - DFS support is incomplete (known issue with MT7613) - MT7613 radio may stop responding when idling, reboot required. This was an issue with the ddc75ff704 version of mt76, but appears to have improved/disappeared with bc3963764d. Error notice example: [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout Hardware was kindly provided for porting by Stijn Segers. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 1e75909a35a2b361cdfdfcf18a26ad61271b174e)
* ramips: mark toggle input on EX6150 as a switchKurt Roeckx2021-02-151-0/+1
| | | | | | | | | The Netgear EX6150 has an Access Point/Extender switch. Set it as an EV_SW. Otherwise when it's set to Access Point, it will trigger failsafe mode during boot. Fixes: FS#3590 Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
* ramips: add support for ELECOM WRC-1167FSINAGAKI Hiroshi2021-02-111-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Cudy WR1300Andrew Pikler2021-02-091-0/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7612E - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB - Power: DC 12V 1A tip positive UART Serial: 115200 baud Located on unpopulated 4 pin header near J4: J4 [o] Rx [o] Tx [o] GND [ ] Vcc - Do not connect Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html MAC addresses as verified by OEM firmware: use address source LAN *:f0 label WAN *:f1 label + 1 2g *:f0 label 5g *:f2 label + 2 The label MAC address is found in bdinfo 0xde00. Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
* ramips: add support for JCG Y2Chukun Pan2021-02-091-0/+130
| | | | | | | | | | | | | | | | | | | | | | | | JCG Y2 is an AC1300M router Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615) Ethernet: 10/100/1000 Mbps x5 LED: POWER, INTERNET, 2.4G, 5G Button: Reset Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page. MAC addresses map: 0x0004 *:c8 wlan2g/wlan5g/label 0xe000 *:c7 lan 0xe006 *:c6 wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add support for I-O DATA WN-DX1200GRINAGAKI Hiroshi2021-02-071-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : raw NAND 128 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7603E - 5 GHz : MediaTek MT7613BE - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/keys : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: 3.3V, TX, RX, NC, GND from triangle-mark - 57600n8 - Power : 12 VDC, 1 A Flash instruction using initramfs image: 1. Boot WN-DX1200GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with the squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - currently, mt7615e driver in mt76 doesn't fully support MT7613 (MT7663) wifi chip - the eeprom data in flash is not used by mt7615e driver and the driver reports the tx-power up to 3dBm - the correct MAC address for MT7613BE in eeprom data cannot be assigned to the phy - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" (called as "combo image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC") - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32" - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b) : kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs MAC addresses: LAN: 50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex)) WAN: 50:41:B9:xx:xx:0A (Factory, 0x1E006 (hex)) 2.4GHz: 50:41:B9:xx:xx:08 (Factory, 0x4 (hex)) 5GHz: 50:41:B9:xx:xx:09 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [add check whether dflag_offset is set] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace full-text licenses by SPDX identifierAdrian Schmutzler2021-02-0512-269/+12
| | | | | | | | | | This replaces several full-text and abbreviated licenses found in DTS files by the corresponding SPDX identifiers. This should make it easier to identify the license both by humans and machines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for UniElec U7621-01David Bentham2021-02-052-0/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7621-01 is a router platform board, the smaller model of the U7621-06. The device has the following specifications: - MT7621AT (880 MHz) - 256 of RAM (DDR3) - 16 MB of FLASH (SPI NOR) - 5x 1 Gbps Ethernet (MT7621 built-in switch) - 1x 2.4Ghz MT7603E - 1x 5Ghz MT7612 - 1x miniPCIe slots (PCIe bus only) - 1x miniSIM slot - 1x USB 2.0 (uses the usb 3.0 driver) - 8x LEDs (1x GPIO-controlled) - 1x reset button - 1x UART header (4-pins) - 1x GPIO header (30-pins) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - 1x 2.4Ghz MT7603E (wifi) - 1x 5Ghz MT7612 (wifi) - miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) - miniSIM slot (works with normal size simcard) - sysupgrade - reset button Installation: This board has no locked down bootloader. The seller can be asked to install openwrt v18.06, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. LEDs list (left to right): - ESW_P0_LED_0 - ESW_P1_LED_0 - ESW_P2_LED_0 - ESW_P3_LED_0 - ESW_P4_LED_0 - CTS2_N (GPIO10, configured as "status" LED) - LED_WLAN# (connected with pin 44 in wifi1 slot) Signed-off-by: David Bentham <db260179@gmail.com> [add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Hi-Link HLK-7688AEwan Parker2021-02-051-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7688AN - RAM: 128 MB - Flash: 32 MB - Ethernet: 5x 10/100 (1x WAN, 4x LAN) - Wireless: built in 2.4GHz (bgn) - USB: 1x USB 2.0 port - Buttons: 1x Reset - LEDs: 1x (WiFi) Flash instructions: - Configure TFTP server with IP address 10.10.10.3 - Name the firmware file as firmware.bin - Connect any Ethernet port to the TFTP server's LAN - Choose option 2 in U-Boot - Alternatively choose option 7 to upload firmware to the built-in web server MAC addresses as verified by OEM firmware: use address source 2g *:XX factory 0x4 LAN *:XX+1 factory 0x28 WAN *:XX+1 factory 0x2e Notes: This board is ostensibly a module containing the MediaTek MT7688AN SoC, 128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in IoT Gateway Mode or IoT Device Mode. From some vendors the U-Boot that comes installed operates on UART 2 which is inaccessible in gateway mode and operates unreliably in the Linux kernel when using more than 64 MB of RAM. For those, updating U-Boot is recommended. Signed-off-by: Ewan Parker <ewan@ewan.cc> [add WLAN to 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ELECOM WRC-2533GHBK-IINAGAKI Hiroshi2021-01-291-0/+199
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, RX, GND, TX from SoC side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-2533GHBK-I normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing MAC addresses: LAN : BC:5C:4C:xx:xx:89 (Config, ethaddr (text)) WAN : BC:5C:4C:xx:xx:88 (Config, wanaddr (text)) 2.4GHz : BC:5C:4C:xx:xx:8A (Factory, 0x4 (hex)) 5GHz : BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* kernel: mtdsplit_uimage: replace "edimax, uimage" parserBjørn Mork2021-01-227-7/+28
| | | | | | | | The "edimax,uimage"" parser can be replaced by the generic parser using device specific openwrt,partition-magic and openwrt,offset properties. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: mtdsplit_uimage: replace "openwrt, okli" parserBjørn Mork2021-01-221-1/+3
| | | | | | | | | The only difference between the "openwrt,okli" and the generic parser is the magic. Set this in device tree for all affected devices and remove the "openwrt,okli" parser. Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202 Signed-off-by: Bjørn Mork <bjorn@mork.no>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 16:16:09 +0000