aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix power LED DTB for wt3020Emil Muratov2018-09-261-1/+1
| | | | | | | Since c134210 power LED is no longer lights after boot-up. Reversing gpio polarity makes it work as it should be. Signed-off-by: Emil Muratov <gpm@hotplug.ru>
* ramips: add support for TP-Link TL-MR3020 v3Carlo Nel2018-09-061-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N. This PR is based on the work of @meyergru[1], with his permission. Specification: - MediaTek MT7628N/N (575 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet Flash instruction: The only way to flash the image in TL-MR3020 v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. [1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3 Signed-off-by: Carlo Nel <carlojnel@gmail.com>
* ramips: add mt7620/1 sdhci pinmuxMathias Kresin2018-09-068-16/+13
| | | | | | | Set the pins to the required mode via the pinmux driver. It allows to get rid of the pinmux related code in the sd card driver. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix mt7620a ND/SD pins pinmuxesMathias Kresin2018-09-064-4/+4
| | | | | | | | | | Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually exclusive and for most of the boards not even used as GPIOs. If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still GPIOs (#45 and #46). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: reference node by labelMathias Kresin2018-09-061-4/+4
| | | | | | Reference the HC5661A sdhci node by label instead of by the full path. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix rt3883 pinmux for second SPIMathias Kresin2018-08-291-2/+2
| | | | | | | The rt3883 doesn't have a pinmux group named spi_cs1. The cs1 is part of the pci group. The function pci-func enables the second chip select. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix rt3883 pci pinmuxMathias Kresin2018-08-291-1/+1
| | | | | | | | | | The PCI pins need to be set to "PCI Host support one device" to allow the use of one PCI device and flash memory. The pci-fnc function is intended to be used if no PCI is used but flash, nand or the codec functionality is. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add missing zbt-cpe102 diag ledMathias Kresin2018-08-291-1/+6
| | | | | | | Based on the userspace led configuration it's quite obvious that the 4g-0 led should be used for boot status indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: express diag led handling via devicetreeMathias Kresin2018-08-295-3/+12
| | | | | | | Use the default-state property to express the desired led handling in the devicetree source file instead of the userspace. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix multi colour led handlingMathias Kresin2018-08-294-2/+14
| | | | | | | | All boards either have a multi colour led or a single lightpipe. It makes it impossible to handle the LEDs individual. Change the LED config for these boards to take it into account. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-2714-20/+4
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: fix mt7620 pinmux for second SPIMathias Kresin2018-08-272-4/+4
| | | | | | | | | | | The mt7620 doesn't have a pinmux group named spi_cs1. The cs1 is part of the "spi refclk" group. The function "spi refclk" enables the second chip select. On reset, the pins of the "spi refclk" group are used as reference clock and GPIO. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix RBM11G partitioningThibaut VARÈNE2018-08-241-9/+36
| | | | | | | | | | | | | | | | | | | | | | | | | This patch improves faf64056ddd46992a75b1e277d94541c7251035c by correcting the partition scheme for the "RouterBoot" section of the flash. The partition scheme initially submitted is incorrect and does not reflect the actual flash structure. The "RouterBoot" section (name matching OEM) is subdivided in several static segments, as they are on ar71xx RB devices albeit with different offsets and sizes. The naming convention from ar71xx has been preserved, except for the bootloaders which are named "bootloader1" and "bootloader2" to avoid confusion with the master "RouterBoot" partition. The preferred 'fixed-partitions' DTS node syntax is used, with nesting support as introduced in 2a598bbaa3. "partition" is used for node names, with associated "label" to match policy set by 6dd94c2781. Leave a note in DTS to explain how the original author selected the SPI speed. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix RBM33G partitioningThibaut VARÈNE2018-08-241-9/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch improves 5684d087418d176cfdef4e045e1950ca7ba3b09f by correcting the partition scheme for the "RouterBoot" section of the flash. The partition scheme initially submitted is incorrect and does not reflect the actual flash structure. The "RouterBoot" section (name matching OEM) is subdivided in several static segments, as they are on ar71xx RB devices albeit with different offsets and sizes. The naming convention from ar71xx has been preserved, except for the bootloaders which are named "bootloader1" and "bootloader2" to avoid confusion with the master "RouterBoot" partition. The preferred 'fixed-partitions' DTS node syntax is used, with nesting support as introduced in 2a598bbaa3. "partition" is used for node names, with associated "label" to match policy set by 6dd94c2781. The OEM source code also define a "RouterBootFake" partition at the beginning of the secondary flash chip: to avoid trouble if OEM ever makes use of that space, it is also defined here. The resulting partition scheme looks like this: [ 10.114241] m25p80 spi0.0: w25x40 (512 Kbytes) [ 10.118708] 1 fixed-partitions partitions found on MTD device spi0.0 [ 10.125049] Creating 1 MTD partitions on "spi0.0": [ 10.129824] 0x000000000000-0x000000040000 : "RouterBoot" [ 10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot [ 10.142894] Creating 5 MTD partitions on "RouterBoot": [ 10.148032] 0x000000000000-0x00000000f000 : "bootloader1" [ 10.154336] 0x00000000f000-0x000000010000 : "hard_config" [ 10.160665] 0x000000010000-0x00000001f000 : "bootloader2" [ 10.167046] 0x000000020000-0x000000021000 : "soft_config" [ 10.173461] 0x000000030000-0x000000031000 : "bios" [ 10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes) [ 10.194950] 2 fixed-partitions partitions found on MTD device spi0.1 [ 10.201271] Creating 2 MTD partitions on "spi0.1": [ 10.206071] 0x000000000000-0x000000040000 : "RouterBootFake" [ 10.212746] 0x000000040000-0x000001000000 : "firmware" [ 10.307216] 2 minor-fw partitions found on MTD device firmware [ 10.313044] 0x000000040000-0x000000220000 : "kernel" [ 10.319002] 0x000000220000-0x000001000000 : "rootfs" [ 10.324906] mtd: device 9 (rootfs) set to be root filesystem [ 10.330678] 1 squashfs-split partitions found on MTD device rootfs [ 10.336886] 0x000000b40000-0x000001000000 : "rootfs_data" Leave a note in DTS to explain how the original author selected the SPI speed. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Rafał Miłecki <rafal@milecki.pl> [rmilecki: dropped "RouterBootFake" partition] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for ELECOM WRC-1900GSTNOGUCHI Hiroshi2018-08-233-172/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: fix compatibles in SoC dtsiMathias Kresin2018-08-233-3/+3
| | | | | | | The former used compatibles aren't defined anywhere and aren't used by the devicetree source files including them. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix GL-MT300N-V2 SoC compatibleMathias Kresin2018-08-231-1/+1
| | | | | | | | According to abbfcc85259a ("ramips: add support for GL-inet GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC compatible to match the used hardware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop not existing groups from pinmuxMathias Kresin2018-08-2310-10/+10
| | | | | | | | | | | | | | RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't have a jtag group. Having these groups defined might cause a boot panic. The pin controller fails to initialise for kernels > 4.9 if invalid groups are used. If a subsystem references a pin controller configuration node, it can not find this node and errors out. In worst case it's the SPI driver which errors out and we have no root filesystem to mount. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-151-0/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for HiWiFi HC5861Bold-masterDeng Qingfang2018-08-141-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN https://www.hiwifi.com/enjoy-view Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7612EN 802.11ac 2T2R 867Mbps - 5x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Everything is working Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-131-48/+44
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear R6120Ludwig Thomeczek2018-08-131-0/+145
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6120, aka Netgear AC1200. Specification: - SoC: MediaTek MT7628 (580 MHz) - Flash: 16 MiB - RAM: 64 MiB - Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E) - LAN speed: 10/100 - LAN ports: 4 - WAN speed: 10/100 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 To flash use nmrpflash with the provided factory.img. Flashing via webinterface will not work, for now. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ramips: use #include syntax for dtsi filesMathias Kresin2018-08-082-2/+2
| | | | | | Use the same syntax for including dtsi for all dts files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove superfluous & confusing DT bindingDaniel Gimpelevich2018-08-064-4/+0
| | | | | | | | | | | Mediatek has a reference platform that pairs an MT7620A with an MT7530W, where the latter responds on MDIO address 0x1f while both chips respond on 0x0 to 0x4. The driver special-cases this arrangement to make sure it's talking to the right chip, but two different ways in two different places. This patch consolidates the detection without the current requirement of both tests to be separately satisfied in the DTS. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: add support for Edimax BR-6478AC v2Daniel Gimpelevich2018-08-061-0/+215
| | | | | | | | | | | | | | | | | | | | | | | | Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie. Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated. Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Macronix MX25L6405D - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7612E 5GHz 802.11ac - Switch: Mediatek MT7530W Gigabit Switch - USB: Yes 1 x 2.0 Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 4. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: move partitions into partition table nodeAlex Maclean2018-08-04257-6412/+7454
| | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: unify partition node names in dts filesMathias Kresin2018-08-043-12/+17
| | | | | | | Use partition@ as name for all partition nodes. Add a label where necessary. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix whitespace and comment issues in dtsMathias Kresin2018-08-0428-86/+82
| | | | | | | | Fix space vs. tabs issue and trainling whitespaces. Use C style comments or drop the comments if they explain what is already to see in the devicetree parameters. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix dtc warningsMathias Kresin2018-08-04232-492/+27
| | | | | | Fix individual boards dtc warnings or obvious mistakes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix hnat dtc warningMathias Kresin2018-08-041-11/+11
| | | | | | | | | | The hardware NAT node has the same reg/unit as the ethernet node. One of them need to be a child of the other. Make the hardware NAT node a child of the ethernet node since the it "reference" the netdev in its properties. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix pci/pcie related dtc warningsMathias Kresin2018-08-0466-684/+575
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the ranges property to the PCI bridges where missing. Add the unit address to PCI bridge where missing. Rework the complete rt3883 pci node. Drop the PCI unit nodes from the dtsi. They are not used by any dts file and should be rather in the dts than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the pci interrupt controller out of the pci node. It doesn't share the same reg and therefore should be an independent/SoC child node. Move the pci related rt3883 pinctrl setting to the dtsi instead of defining the very same for each rt3883 board. If the device_type property is used for PCI units, the unit is treated as pci bridge which it isn't. Drop it for PCI units. Reference pci-bridges or the pci node defined in the dtsi instead of recreating the whole node hierarchy. It allows to change the referenced node in the dtsi without the need to touch all dts. Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips are the first device on the bus. The unit address has to be the bus address instead of the PCI vendor/device id. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use ralink,nr-gpio instead of ralink,num-gpiosMathias Kresin2018-08-047-23/+23
| | | | | | | | | | | Since commit c1e7738988f5 ("checks: add gpio binding properties check") dtc treats any *-gpios and *-gpio property as phandle at least during checks. The only whitelisted property is nr-gpio. Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false positive warnings. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix cpu interrupt controller dtc warningsMathias Kresin2018-08-048-8/+8
| | | | | | | The cpu interrupt controller doesn't have a reg property, hence we can't use a unit address in the node name. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix cpu related dtc warningsMathias Kresin2018-08-049-2/+34
| | | | | | We need a reg property if we are using a unit address. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for ELECOM WRC-2533GSTINAGAKI Hiroshi2018-07-301-0/+178
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - MT7621A (2-Core, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 4T4R 2.4/5 GHz wifi - MediaTek MT7615 - 5x 10/100/1000 Mbps Ethernet - 4x LEDs, 6 keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-2533GST 2. Connect power cable to WRC-2533GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: fix RBM11G nameThibaut VARÈNE2018-07-301-1/+1
| | | | | | | | The device name is corrected to match the hardware-stored (in hard config flash space) device name. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: fix RBM33G nameThibaut VARÈNE2018-07-301-1/+1
| | | | | | | | The device name is corrected to match the hardware-stored (in hard config flash space) device name. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: mmc: Add SD card support to HC5661ALoveSy2018-07-301-0/+4
| | | | | | | | | | Tested on HC5661A and it now fixes the issue that when enabling sd card in HC5661A, the wan and 3 lan ports will down. Known issue: - When enabling SD card support, the led light of system will down and the rest 2 lights keep working. Signed-off-by: LoveSy <shana@zju.edu.cn>
* ramips: Use dts alias based status ledChuanhong Guo2018-07-16207-208/+1034
| | | | | | Also fix several typos in led node name. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: TP-Link TL-WR902AC v3: add missing wps buttonPeter Lundkvist2018-07-121-1/+7
| | | | Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ramips: add support for Blueendless Kimax U35WFAdemar Arvati Filho2018-07-071-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908 Based on: https://github.com/lede-project/source/pull/965 Specification: - SoC: MediaTek MT7620N - CPU/Speed: 580 MHz - Flash-Chip: KH25L12835F Spi Flash - Flash size: 16 MiB - RAM: 64 MiB - LAN: 1x 100 Mbps Ethernet - WiFi SoC-integrated: 802.11bgn - 1x USB 2.0 - UART: for serial console Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 3. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* ramips: add support for I-O DATA WN-AX1167GRINAGAKI Hiroshi2018-07-071-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Stock firmware: In the stock firmware, WN-AX1167GR has two os images each composed of Linux kernel and rootfs. These images are stored in "Kernel" and "app" partition of the following partitions, respectively. (excerpt from dmesg): MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" The flag for boot partition is stored in "Key" partition, and U-Boot reads this and determines the partition to boot. If the image that U-Boot first reads according to the flag is "Bad Magic Number", U-Boot then tries to boot from the other image. If the second image is correct, change the flag to the number corresponding to that image and boot from that image. (example): ## Booting image at bc800000 ... Bad Magic Number,FFFFFFFF Boot from KERNEL 1 !! ## Booting image at bc060000 ... Image Name: MIPS OpenWrt Linux-4.14.50 Image Type: MIPS Linux kernel Image (lzma compressed) Data Size: 1865917 Bytes = 1.8 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK raspi_erase_write: offs:f90000, count:34 . . Done! Starting kernel ... Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AX1167GR 2. Connect power cable to WN-AX1167GR and turn on it 3. Access to "192.168.0.1" on the web browser and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and perform firmware update 5. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR 6. Wait ~180 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for TL-WA801ND v5Romain MARIADASSOU2018-07-041-0/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MediaTek MT7628NN - CPU/Speed: 580 MHz - Flash-Chip: ELM Technology GD25Q64 - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn Currently the only method to install openwrt for the first time is via TFTP recovery. After first install you can use regular updates. Flash instructions: 1) To flash the recovery image, start a TFTP server with IP address 192.168.0.66 and serve the recovery image named tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS and Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds or until the lock LED is lighting up. It will try to download the recovery image and flash it. It can take up to 2-3 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
* ramips: add support for ZyXEL Keenetic Extra IIMaxim Anisimov2018-07-041-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7628N/N - CPU/Speed: 580 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (57600 8n1) - Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn - Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac - USB: Yes 1 x 2.0 - 4x LED, 3x button The device supports dual boot mode. So we use only first half of flash. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin" to "kextra2_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for MikroTik RouterBOARD RBM11gTobias Schramm2018-07-041-0/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik RouterBOARD RBM11g. =Hardware= The RBM11g is a mt7621 based device featuring one GbE port and one miniPCIe slot with a sim card socket and USB 2.0. ==Switch== The single onboard Ethernet port is connected the CPU directly. The internal switch of the mt7621 SoC is disabled. ==Flash== The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS connected to CS0. ==PCIe== The board features a single miniPCIe slot. It has a dedicated mini SIM socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via GPIO9. ==USB== There are no external USB ports. ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack (center-positive). The input voltage range is 11-32 V. ==Serial port== The device does have an onboard UART on an unpopulated header next to the flash chip: GND: pin 2 TX: pin 7 RX: pin 6 Settings: 115200, 8N1 See below illustration for positioning of the header. 0 = screw hole * = some pin T = TX pin R = RX pin G = GND pin Pinout: +--------------- |O | __ | / \ | \__/ | | | | +---+ | |RAM| | +--+ | | | |**| <- unpopulated header with UART | |*T| +---+ | |R*| +--------+ | |**| | | | |G*| | CPU | | +--+ | | | +--+ | | | | | +--------+ | +--+ <- flash chip |O | +-----+ | | | |+--+ | | || | | | +--------------------- =Installation= To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM11G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** When rebooted the board will try booting via ethernet first. If your board does not boot via ethernet automatically you will have to attach to the serial port and set ethernet as boot device within RouterBOOT. 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" initramfs image 2. Connect to ethernet port on board 3. Power on the board 4. Wait for OpenWrt to boot Right now OpenWrt will be running with a SSH server listening. Now OpenWrt must be flashed to the devices flash: 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" Once the flashing completes the board will reboot. Disconnect from the devices ethernet port or stop the DHCP/TFTP server to prevent the device from booting via ethernet again. The device should now boot straight to OpenWrt. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: move mt7620n i2c_pins definition to right placeAndrey Jr. Melnikov2018-06-281-7/+7
| | | | | | | | | | Move to i2c pins pinmux node to the pinctrl node. Fixes: a0685deec458 ("ramips: Add i2c support for mt7620n") Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com> [fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link Archer C2Franz Flasch2018-06-251-0/+178
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Winbond 25Q64BVSIG - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac - Switch: RTL8367RB Gigabit Switch - USB: Yes 1 x 2.0 Preparing a TFTP recovery image for initial flashing: Currently the only method to install openwrt for the first time is via TFTP download in u-boot. After first install you can use regular updates. WARNING: This method also overwrites the bootloader partition! Create a TFTP recovery image: 1) Download a stock TP-Link Firmware file here: https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware 2) Extract u-boot from the binary file: #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072 3) Now merge the sysupgrade image and the u-boot into one binary: #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin The resulting image can be flashed via TFTP recovery mode. Flash instructions: 1) To flash the recovery image, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC2V1_tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS/Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds. It will try to download the recovery image and flash it. It can take up to 20-25 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: fix ZyXEL Keenetic Viva switch configFranz Flasch2018-06-251-1/+1
| | | | | | | | | The rtl8367b driver never supported a mdio property and it is quite likely that the switch never worked for the board. Use the mii-bus property instead to manage the switch via a mdio bus. Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: Add support for Phicomm K2GChuanhong Guo2018-06-211-0/+139
| | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Add support for Mikrotik RouterBOARD RBM33gTobias Schramm2018-06-211-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik RouterBOARD RBM33g. =Hardware= The RBM33g is a mt7621 based device featuring three gigabit ports, 2 miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male onboard RS-232 serial port. Additionally there are a lot of accessible GPIO ports and additional buses like i2c, mdio, spi and uart. ==Switch== The three Ethernet ports are all connected to the internal switch of the mt7621 SoC: port 0: Ethernet Port next to barrel jack with PoE printed on it port 1: Innermost Ethernet Port on opposite side of RS-232 port port 2: Outermost Ethernet Port on opposite side of RS-232 port port 6: CPU ==Flash== The device has two spi flash chips. The first flash chips is rather small (512 kB), connected to CS0 by default and contains only the RouterBOOT bootloader and some factory information (e.g. mac address). The second chip has a size of 16 MB, is by default connected to CS1 and contains the firmware image. ==PCIe== The board features three PCIe-enabled slots. Two of them are miniPCIe slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2). Each of the miniPCIe slots is connected to a dedicated mini SIM socket on the back of the board. Power to all three PCIe-enabled slots is controlled via GPIOs on the mt7621 SoC: PCIe0: GPIO9 PCIe1: GPIO10 PCIe2: GPIO11 ==USB== The board has one external USB 3.0 port at the rear. Additionally PCIe port 0 has a permanently enabled USB interface. PCIe slot 1 shares its USB interface with the rear USB port. Thus only either the rear USB port or the USB interface of PCIe slot 1 can be active at the same time. The jumper next to the rear USB port controls which one is active: open: USB on PCIe 1 is active closed: USB on rear USB port is active ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack. The input voltage range is 11-32 V. =Installation= ==Prerequisites== A USB -> RS-232 Adapter and a null modem cable are required for installation. To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM33G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** Serial settings: 115200 8N1 The installation is a two-step process. First the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted via tftp: 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" initramfs image 2. Connect to WAN port (left side, next to sys-LED and power indicator) 3. Connect to serial port of board 4. Power on board and enter RouterBOOT setup menu 5. Set boot device to "boot over ethernet" 6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server allows dynamic bootp) 6. Save config 7. Wait for board to boot via Ethernet On the serial port you should now be presented with the OpenWRT boot log. The next steps will install OpenWRT persistently. 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" Once the flashing completes reboot the router and let it boot from flash. It should boot straight to OpenWRT. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 07:26:25 +0000