aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/mt7628an_netgear_r6120.dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: consolidate Netgear devices for mt7628Adrian Schmutzler2020-07-131-78/+15
| | | | | | | | | | | | | | | This creates a common DTSI and shared image definition for the relatively similar Netgear devices for mt7628 platform. As a side effect, this raises SPI flash frequency for the R6120, as it's expected to work there as well if it works for R6080 and R6020. Based on the data from the other devices, it also seems probable the 5g MAC address for R6120 could be extracted from the caldata, and the mtd-mac-address there could be dropped. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move Netgear R6120 LED trigger to DTSAlex Lewontin2020-06-231-0/+1
| | | | | | | | | | | | This moves the trigger for the Netgear R6120's wlan2g_green LED from base-files/etc/board.d/01_leds to the device-tree file. This has been applied to R6120 based on findings for the very similar Netgear R6080. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [merge case in 01_leds, slightly adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace pinctrl property namesChuanhong Guo2020-04-121-2/+2
| | | | | | | | | | | | | | Upstream pinctrl driver in drivers/staging uses groups/function/ralink,num-gpios instead of ralink,group/ralink,function/ralink,nr-gpio Replace these properties in dts as well as the pinctrl driver in patches-4.14. This commit is created using: sed -i 's/ralink,group/groups/g' sed -i 's/ralink,function/function/g' sed -i 's/ralink,nr-gpio/ralink,num-gpios/g' Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7628: update dts for upstream gpio-mt7621 driverChuanhong Guo2020-04-121-8/+8
| | | | | | | | | | upstream driver merged 3 separated gpio banks into one gpio node. and gpioX Y in our local driver should be replaced with gpio X*32+Y. This patch is created using the following sed command: sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge' Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: harmonize Netgear R6120 DT LED node namesAlex Lewontin2020-04-061-3/+3
| | | | | | | | | This changes the node names for the LEDs in the Netgear R6120 device-tree file to provide consistency with other devices. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [improve commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: simplify state_default/pinctrl0 in device DTS filesAdrian Schmutzler2019-12-231-8/+6
| | | | | | | | | The node pinctrl0 is already set up in the SOC DTSI files, but defined again as member of pinctrl in most of the device DTS(I) files. This patch removes this redundancy for the entire ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-eeprom in mt76x8 DTS filesAdrian Schmutzler2019-10-271-1/+0
| | | | | | | | | | In mt7628an.dtsi, calibration data for wmac is already defined: mediatek,mtd-eeprom = <&factory 0x0>; Thus, this patch removes redundant entries of this property in derived DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-mac-address for WiFiAdrian Schmutzler2019-10-271-1/+0
| | | | | | | | | | When caldata locations are defined with mediatek,mtd-eeprom the MAC address is automatically read from offset +4. Thus, specifying that location explicitly is redundant. This patch removes those redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt762x: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-10-211-2/+1
| | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. While at it, add/remove newlines in keys and leds node where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide label MAC addressAdrian Schmutzler2019-09-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ramips. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - cudy,wr1000 - dlink,dir-615-d - dlink,dir-615-h1 - dlink,dir-860l-b1 - glinet,gl-mt300a - glinet,gl-mt300n - glinet,gl-mt750 - vocore,vocore2 - vocore,vocore2-lite - zbtlink,zbt-we1326 - zbtlink,zbt-wg3526 For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - dlink,dir-510l - dlink,dwr-116-a1 - dlink,dwr-118-a1 - dlink,dwr-118-a2 - dlink,dwr-921-c1 - dlink,dwr-922-e2 - all hiwifi devices - lava,lr-25g001 - xiaomi,mir3p Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: dts: drop memory nodesChuanhong Guo2019-07-111-5/+0
| | | | | | | | mt7621 and mt7628 now have the ability to detect memory size automatically. Drop memory nodes and let kernel determine memory size. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips/mt76x8: Name DTS files based on schemeAdrian Schmutzler2019-07-101-0/+161
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-06 12:22:43 +0000