| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | ramips: mt7621: update dts/defconfig for DSA | DENG Qingfang | 2020-04-04 | 1 | -1/+31 |
| | | | | | | | | | | | | update dts and network/LED configuration for DSA driver. sysupgrade from images prior to this commit with config preserved will cause broken ethernet setup. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Acked-by: Jo-Philipp Wich <jo@mein.io> [split commit] Signed-off-by: Chuanhong Guo <gch981213@gmail.com> | ||||
| * | ramips: mt7621: update pinctrl nodes | DENG Qingfang | 2020-04-04 | 1 | -2/+2 |
| | | | | | | | Upstream GPIO driver uses "groups" "function" properties Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> | ||||
| * | ramips: mt7621: convert GPIO dts refs | DENG Qingfang | 2020-04-04 | 1 | -5/+5 |
| | | | | | | | | The upstream driver does not use &gpio0..2 banks notation anymore, so convert them to &gpio Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> | ||||
| * | ramips: simplify state_default/pinctrl0 in device DTS files | Adrian Schmutzler | 2019-12-23 | 1 | -6/+4 |
| | | | | | | | | | | The node pinctrl0 is already set up in the SOC DTSI files, but defined again as member of pinctrl in most of the device DTS(I) files. This patch removes this redundancy for the entire ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | ||||
| * | ramips: clean and improve MAC address setup in 02_network | Adrian Schmutzler | 2019-09-07 | 1 | -1/+1 |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes unnecessary MAC address setup statements in ramips' 02_network by doing several optimizations: 1. For the following devices, lan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The lan_mac statement is removed in 02_network, but wan_mac is kept: - mercury,mac1200r-v2 - phicomm,k2g - skylab,skw92a - wiznet,wizfi630a 2. For the following devices, wan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The wan_mac statement is removed in 02_network, no lan_mac is present: - buffalo,whr-g300n - glinet,gl-mt300n-v2 - zyxel,keenetic-start 3. For the following device, lan_mac and wan_mac were set up with mtd_get_mac_binary to the same address as set in DTS. Both statements are removed in 02_network: - buffalo,whr-600d 4. For some devices, it was possible to move setup from 02_network to DTS by introducing previously missing mtd_mac_address: - buffalo,whr-1166d - buffalo,whr-300hp2 - buffalo,wsr-600dhp - ohyeah,oy-0001 - planex,vr500 5. For one device, mtd_mac_address was just wrong and overwritten by 02_network. Put the correct value in DTS and remove redundant statement in 02_network: - asus,rt-ac57u 6. For one device, MAC address defined in DTS is exchanged together with lan_mac/wan_mac setup in 02_network, so that cases in 02_network can be merged: - phicomm,k2p For some devices, an empty case has to be used to prevent them from falling into the default case and have WAN address = eth0 address + 1 set to them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> | ||||
| * | ramips: add support for ASUS RT-AC57U | David Bauer | 2019-07-11 | 1 | -0/+148 |
| SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net> | |||||
 |
index : openwrt/upstream | |
| upstream openwrt | James |
| aboutsummaryrefslogtreecommitdiffstats |