aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/kn_rc.dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for indicating the boot state using multiple ledsMathias Kresin2018-10-071-1/+4
| | | | | | | | | Use diag.sh version used for other targets supporting different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: set usb led trigger via devicetreeMathias Kresin2018-10-071-0/+2
| | | | | | | | | | Assign the usbdev trigger via devicetree for all subtargets and drop the userspace handling of the usb leds. With the change all usb ports are triggering the usb led instead of only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move partitions into partition table nodeAlex Maclean2018-08-041-23/+27
| | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: fix dtc warningsMathias Kresin2018-08-041-2/+0
| | | | | | Fix individual boards dtc warnings or obvious mistakes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Use dts alias based status ledChuanhong Guo2018-07-161-1/+5
| | | | | | Also fix several typos in led node name. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: update device tree source filesL. D. Pinney2017-08-031-0/+1
| | | | | | | | Use the GPIO dt-bindings macros and add compatible strings in the ramips device tree source files. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix ZyXEL Keenetic Omni/Omni II GPIOsAlexey Belyaev2017-04-251-3/+11
| | | | | | | Each GPIO bank has only 24 gpios. Use and enable the correct banks for GPIOs > 24. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* ramips: fix ZyXEL Keenetic Omni switch configAlexey Belyaev2017-04-251-1/+1
| | | | | | | The wan port is connected to switch port 0. Fix the mediatek,portmap as well as the default switch config. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* ramips: replace remaining instances of ralink, port-mapDaniel Golle2017-02-151-1/+1
| | | | | | | | | | | | Some boards were apparently forgotten when ralink,portmap was renamed to mediatek,portmap -- probably because they used the long obsolete ralink,port-map attribute. If this commit breaks ethernet wan/lan assignment, this is because the port-map attribute wasn't actually parsed, you'll have to replace "wllll" by "llllw" in the dts file belonging to that board (and send a patch doing that!) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb powerVitaly Chekryzhev2017-01-261-0/+11
| | | | | | Export gpio usb to allow power management of USB port. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-221-0/+120
Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>