aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/WMDR-143N.dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips/rt288x,rt3883: Name DTS files based on schemeAdrian Schmutzler2019-07-101-69/+0
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: specify "firmware" partition formatINAGAKI Hiroshi2018-11-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specify firmware partition format by compatible string. formats in ramips: - denx,uimage - tplink,firmware - seama It's unlikely but the firmware splitting might not work any longer for the following boards, due to a custom header: - EX2700: two uImage headers - BR-6478AC-V2: edimax-header - 3G-6200N: edimax-header - 3G-6200NL: edimax-header - BR-6475ND: edimax-header - TEW-638APB-V2: umedia-header - RT-N56U: mkrtn56uimg But it rather looks like the uImage splitter is fine with the extra header. The following dts are not touched, due to lack of a compatible string in the matching firmware splitter submodule: - CONFIG_MTD_SPLIT_JIMAGE_FW DWR-116-A1.dts DWR-118-A2.dts DWR-512-B.dts DWR-921-C1.dts LR-25G001.dts - CONFIG_MTD_SPLIT_TRX_FW WCR-1166DS.dts WSR-1166.dts - CONFIG_MTD_SPLIT_MINOR_FW RBM11G.dts RBM33G.dts - CONFIG_MTD_SPLIT_LZMA_FW AR670W.dts - CONFIG_MTD_SPLIT_WRGG_FW DAP-1522-A1.dts Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: move partitions into partition table nodeAlex Maclean2018-08-041-20/+24
| | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for Loewe WMDR-143NOliver Fleischmann2017-07-271-0/+64
The WMDR-143N is a small module originally used as a Wifi client in some Loewe smart TV sets. It is sold cheaply at german surplus shops. The module contains a RT3662 SOC. Specifications: - 500 MHz CPU Clock - 1x 10/100Mbps Ethernet (pin header) - 32 MB of RAM - 8 MB of FLASH - 2T3R 2.4/5 GHz (SOC internal) - 3 Antennas on PCB - UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX and RX are 3,3V only! The square hole is pin 1 - Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND) The square hole is pin 1 The original firmware has two identical kernel/rootfs images and two "Factory" calibration data blocks in flash. The LEDE image leaves only the first "Factory" block in place and uses both "Kernel" blocks and the redundant "Factory" block together to gain enough space for the jffs2 partition. Flash instructions: You need UART and Ethernet connections to flash the board. Use the LEDE "sysupgrade.bin" image with tftp. Apply power to the board and in the first 5 seconds, hit 2 to select TFTP upload. The bootloader asks for board- and server IP addresses and filename. Alternate method: With the vendor firmware running, assign an IP address to the ethernet port, tftp the firmware image to /tmp and write to mtd4 ("KernelA"). Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de> [remove pinctrl node from dts, no pin is used as GPIO] Signed-off-by: Mathias Kresin <dev@kresin.me>